Search NASA⌕ Search

SEARCH · Search NASA

Results for “decal transfer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Optimization of catalyst-coated membranes for enhancing performance in proton exchange membrane electrolyzer cells

To achieve large-scale application of proton exchange membrane electrolyzer cells (PEMECs) for hydrogen production, it is highly desirable to reduce the manufacturing cost while enhancing cell performance. In the PEMPECs, a catalyst-coated membrane (CCM) is the vital component where electrochemical reactions and mass transport mainly occur. The fabrication methods and catalyst layer (CL) structure can significantly affect the cell performance. Herein, for the first time, a comparative study of CCM fabrications with decal transfer and direct spray deposition methods have been conducted by both ex-situ materials characterization and in-situ performance testing in PEMECs. It is found CCMs that are fabricated with a direct spray deposition method display enhanced cell performance compared to CCMs fabricated with a decal transfer method, mainly due to the largely reduced ohmic resistance and improved mass transport. More importantly, cell performance can be greatly enhanced by simply regulating the Nafion ionomer content at the anode CL. The optimal Nafion ionomer content of 10 wt% gives the best cell performance at 80 °C with a low cell voltage of 1.887 V at 2 A cm -2 , outperforming the commercial CCM and most other previous publications. Our study provides a valuable guidance for fabrication and optimization of CCMs with significantly enhanced performance and reduced cost for practical application of the PEMECs.

08 HYDROGEN↗
DOE OSTI2020

Roll-to-roll production of catalyst coated membranes for low-temperature electrolyzers

Here we demonstrate a roll-to-roll (R2R) process for direct coating of anode catalyst layers on a polymer electrolyte membrane for low-temperature water electrolysis. To develop this process, we studied catalyst ink formulation, ink-membrane interactions, and coating quality. The catalyst inks were a mixture of iridium oxide (IrO2) and Nafion in a water and alcohol dispersion medium. The type of alcohol (methanol, ethanol, propanols) and water-to-alcohol ratio were varied to determine their influence on membrane swelling, dispersion quality, and coatability. Interactions of the ink dispersion medium with the membrane were characterized using sessile-drop contact-angle measurements. These measurements show that the ratio of water to alcohol has a strong influence on how rapidly the dispersion media is absorbed by the membrane. Rheology of the catalyst inks was measured to understand the microstructure of the catalyst particles in the ink. This analysis found that 1-propanol leads to better dispersion of the IrO2 particles than ethanol. Small-scale coating samples were prepared to understand coating uniformity and formation of irregularities. Subsequently, two water/1-propanol ratios (90:10 and 75:25) were down-selected for large-scale R2R slot die coating. The R2R catalyst-coated membrane (CCM) coating process increased catalyst layer production throughput by over 500x compared to our standard lab-scale spray coating. The CCMs obtained from this process were tested as single-cell membrane electrode assemblies. They exhibited a cell voltage of 1.91 V at a current density of 2 A/cm2, which is comparable to spray-coated CCMs. In conclusion, the work presented here demonstrates a continuous, scalable manufacturing process that eliminates the need for the decal transfer step typically used in CCM production.

42 ENGINEERING↗
NASA NTRS2000

Thin Film Catalyst Layers for Direct Methanol Fuel Cells

One of the primary obstacles to the widespread use of the direct methanol fuel cell (DMFC) is the high cost of the catalyst. Therefore, reducing the catalyst loading well below the current level of 8-12 mg/cm 2 would be important to commercialization. The current methods for preparation of catalyst layers consisting of catalyst, ionomer and sometimes a hydrophobic additive are applied by either painting, spraying, decal transfer or screen printing processes. Sputter deposition is a coating technique widely used in manufacturing and therefore particularly attractive. In this study we have begun to explore sputtering as a method for catalyst deposition. Present experiments focus on Pt-Ru catalyst layers for the anode.

Witham, C. K.↗
NASA NTRSDate not supplied

Application of Digital Image Correlation in Wind Tunnel

Digital image correlation (DIC) is a non-contact measurement technique that has been used in various applications in multiple industries, from microscopic specimens all the way to large scale structures. This project involved using DIC to capture wing deflection under simulated wind loading at various angles of attack (AoA). A subscale model of a fixed-wing aircraft, shown in Figure 1, was used in the 14-footby 22-footsubsonicwind tunnel at the NASA Langley Research Center. The setup used two pairs of cameras mounted on the ceiling of the tunnel to view the starboard and port side wings. Aluminum framing was used to rigidly mount the cameras to beams in the ceiling. Camera setup challenges due to the confined space included obtaining even lighting and working around infrared (IR) cameras that were used to capture the flow over the wing. Remote connection was used to access data acquisition computers from computers in the control room. Eight measurement locations on each wing were made of 1-inch-diametercircular silver dry transfer decals that did not alter the air flow across the wing. These circles were speckled with a black ink pen and were used for the IR camera as well as for DIC systems. A mock setup outside the wind tunnel was used to optimize the camera setup and verify that the speckled tape provided sufficient correlation. DIC was used to track the position of seven locations as the AoA of the subscale model changed from −10 degrees to +10 degrees in 1-degree increments. The model was rotated at a fixed height about the center of the fuselage from −7 degrees to +10 degrees. The height of the model had to be lowered to achieve AoA slower than −7degrees due to geometric constraints of the cart supporting the model and the wind tunnel. The source of light was stationary relative to the model, so the exposure time had to be adjusted for different wing regions and AoA values. The three-dimensional (3D) visualization of the markings and the two-dimensional (2D) projection of these points onto the port wing at 0-degree AoA is shown in Figure 2.

Matlock Mennu↗
DOE OSTI2020

Influence of Coating Method on the Performance of Roll-to-Roll Coated PEM Fuel Cell Catalyst Layers

As production of fuel cell vehicles and power systems increases there is a need to understand the process science of fuel cell manufacturing. Industrial production of polymer electrolyte membrane fuel cell (PEMFC) electrodes will rely on continuous roll-to-roll (R2R) coating methods to meet the rates needed for mass production. There are a variety of coating methods that could be used to coat catalyst layers. The different physics of each method may result in different morphologies and performance. Here we present the results of a study comparing fuel cell catalyst layers coated using two R2R coating methods: slot-die and gravure. These two methods were selected because the physics of applying the liquid to the substrate is very different between the two cases. Pt/C catalysts layers were coated directly onto carbon-fiber gas diffusion media to create gas diffusion electrodes (GDEs), without the use of a decal transfer process. These GDEs were assembled into membrane electrode assemblies (MEAs) by hot pressing to Nafion membranes. In situ performance and other electrochemical diagnostics were used to determine the influence of coating method on catalyst layer electrochemical properties. Electron microscopy was utilized to understand the influence of coating method on electrode morphology and its influence on electrochemical properties. We also explored the influence of solvent ratio to understand the potential coupling between ink formulation and coating methodology.

DIRECT ENERGY CONVERSION,MATERIALS SCIENCE↗
DOE OSTI2021

Influence of Ink Formulation and Drying Conditions on Ionomer Distribution in High-Performance Roll-to-Roll-Coated Gas-Diffusion Electrodes

To enable mass production of fuel cell membrane electrode assemblies (MEAs) catalyst layers production will require continuous roll-to-roll (R2R) coating processes. Gas diffusion electrodes (GDEs) are advantageous for mass production because the catalyst layer can be directely coated on the microporous layer of the gas diffusion media without the need for a decal-transfer process. It is known that the water-to-alcohol ratio in the catalyst ink influences the interactions of the ionomer with the catalyst leading to different distributions of ionomer in spray-coated catalyst layers. It is also known that during drying of colloidal mixtures, like fuel cell inks, factors such as drying rate, particle size, and agglomeration influence how the materials distribute themselves throughout the thickness of the dired film. Thus far there have only been limited studies to understand how process conditions such as ink formulation and drying temperature influence the distribution of ionomer and catalyst coated using scalable methods. This understanding is especially important for GDEs since it is known that having a sufficient amount of ionomer at the catalyst layer-membrane interface is critical for high performance. In this study we have focused on determining how the ratio of water to 1-propanol in the catalyst ink ink and drying temperature influence the distribution of ionomer throughout the thickness of the catalyst layer. Using a combination of Kelvin probe and x-ray photoelectron spectroscopy we show that an ionomer-rich surface is promoted by a higher drying rate and a water-rich catalyst ink. In contrast, a 1-propanol catalyst ink leads to a lower concentration of ionomer on the top surface. Using x-ray computed tomography, we are able to characterize the ionomer distribution throughout the thickness of the layer. We find that, in addition to promoting an ionomer-rich top surface, water-rich inks lead to a more homogenous distribution of ionomer, whereas a 1-propanol-rich ink leads to a more irregular distribution. It is found that MEA performance is improved by selecting conditions and ink formulations that promote ionomer enrichment at the top surface to facilitate a good interface with the membrane. MEAs prepared with a 75 wt% water catalyst ink with a 0.9 I/C have equivalent performance to spray-coated GDEs. Critically, these R2R-coated GDEs do not need an additional ionomer overlayer like the spray-coated GDEs do, reducing the number of processing steps in a manufacturing setting. This work shows that with the appropriate selection of materials, ink formulation, and processing conditions gas-diffusion electrodes are a viable pathway for fuel cell manufacturing.

ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATION↗