Search NASA⌕ Search

SEARCH · Search NASA

Results for “defect microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Revealing multiple classes of stable quantum emitters in hexagonal boron nitride with correlated optical and electron microscopy

Defects in hexagonal boron nitride (hBN) exhibit high-brightness, room-temperature quantum emission, but their large spectral variability and unknown local structure challenge their technological utility. Here, we directly correlate hBN quantum emission with local strain using a combination of photoluminescence (PL), cathodoluminescence (CL) and nanobeam electron diffraction. Across 40 emitters, we observe zero phonon lines (ZPLs) in PL and CL ranging from 540 to 720 nm. CL mapping reveals that multiple defects and distinct defect species located within an optically diffraction-limited region can each contribute to the observed PL spectra. Local strain maps indicate that strain is not required to activate the emitters and is not solely responsible for the observed ZPL spectral range. Instead, at least four distinct defect classes are responsible for the observed emission range, and all four classes are stable upon both optical and electron illumination. Our findings offer a foundation for future atomic-scale optical characterization of colour centres.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Single-defect phonons imaged by electron microscopy

Crystal defects affect the thermal and heat-transport properties of materials by scattering phonons and modifying phonon spectra. To appreciate how imperfections in solids influence thermal conductivity and diffusivity, it is thus essential to understand phonon–defect interactions. Sophisticated theories are available to explore such interactions, but experimental validation is limited because most phonon-detecting spectroscopic methods do not reach the high spatial resolution needed to resolve local vibrational spectra near individual defects. In this paper, we demonstrate that space- and angle-resolved vibrational spectroscopy in a transmission electron microscope makes it possible to map the vibrational spectra of individual crystal defects. We detect a red shift of several millielectronvolts in the energy of acoustic vibration modes near a single stacking fault in cubic silicon carbide, together with substantial changes in their intensity, and find that these changes are confined to within a few nanometres of the stacking fault. These observations illustrate that the capabilities of a state-of-the-art transmission electron microscope open the door to the direct mapping of phonon propagation around defects, which is expected to provide useful guidance for engineering the thermal properties of materials.

42 ENGINEERING↗
NASA NTRS1992

Leveling coatings for reducing the atomic oxygen defect density in protected graphite fiber epoxy composites

Pinholes or other defect sites in a protective oxide coating provide pathways for atomic oxygen in low Earth orbit to reach underlying material. One concept for enhancing the lifetime of materials in low Earth orbits is to apply a leveling coating to the material prior to applying any reflective and protective coatings. Using a surface tension leveling coating concept, a low viscosity epoxy was applied to the surface of several composite coupons. A protective layer of 1000 A of SiO2 was deposited on top of the leveling coating, and the coupons were exposed to an atomic oxygen environment in a plasma asher. Pinhole populations per unit area were estimated by counting the number of undercut sites observed by scanning electron microscopy. Defect density values of 180,000 defects/sq cm were reduced to about 1000 defects/sq cm as a result of the applied leveling coating. These improvements occur at a mass penalty of about 2.5 mg/sq cm.

Jaworske, D. A.↗
NASA NTRS1992

Leveling coatings for reducing the atomic oxygen defect density in protected graphite fiber epoxy composites

Pinholes or other defect sites in a protective oxide coating provide pathways for atomic oxygen in low Earth orbit to reach underlying material. One concept of enhancing the lifetime of materials in low Earth orbit is to apply a leveling coating to the material prior to applying any reflective and protective coatings. Using a surface tension leveling coating concept, a low viscosity epoxy was applied to the surface of several composite coupons. A protective layer of 1000 A of SiO2 was deposited on top of the leveling coating, and the coupons were exposed to an atomic oxygen environment in a plasma asher. Pinhole populations per unit area were estimated by counting the number of undercut sites observed by scanning electron microscopy. Defect density values of 180,000 defects/sq cm were reduced to about 1000 defects/sq cm as a result of the applied leveling coating. These improvements occur at a mass penalty of about 2.5 mg/sq cm.

Jaworske, D. A.↗
NASA NTRS1974

Effect of surface topography on structural growth of thick sputtered films

Primarily thick sputtered S-Monel, silver, and 304 stainless steel coatings were deposited on mica, glass, and metal substrates with various surface finishes to investigate the structural growth of the coating by scanning electron microscopy. Compositional changes within the coating were analyzed by X-ray dispersion microscopy. Defects in the surface finish act as preferential nucleation sites and form isolated and complex nodules and various surface overgrowths in the coating. These nodules do not disappear after full annealing. Further, they have undesirable effects on mechanial properties; cracks are initiated at the nodules when the coating is stressed by mechanical forces. These effects are illustrated by micrographs. Nodular growth within a coating can be minimized or eliminated by reducing the surface roughness.

Spalvins, T.↗
NASA NTRS1974

Surface topographical effects on the structural growth of thick sputtered metal and alloy coatings

Thick sputtered S-Monel, silver, and 304 stainless steel coatings were deposited on mica and metal substrates with various surface finishes to investigate the structural growth of the coating by scanning electron microscopy. The geometry and the surface structure of the nodules are characterized. Compositional changes within the coating were analyzed by X-ray dispersion microscopy. Defects in the surface finish (i.e., scratches, inclusions, etc.) act as preferential nucleation sites and form isolated and complex nodules and various surface overgrowths in the coating. The nodule boundaries are very vulnerable to chemical etching and these nodules do not disappear after full annealing. Further, they have undesirable effects on mechanical properties; cracks are initiated at the nodules when the coating is stressed by mechanical forces. These effects are illustrated by micrographs. Nodular growth within a coating can be minimized or eliminated by reducing the surface roughness.

Spalvins, T.↗
NASA NTRS1989

Ballistic-electron-emission microscopy of subsurface defects at the Au-GaAs(100) interface

The application of ballistic-electron-emission microscopy (BEEM) to a study of the influence of GaAs(100) substrate conditions on the formation of a multidefect structure at the Au-GaAs(100) Schottky barrier interface is described. Interfaces prepared on both melt-grown GaAs(100) wafer substrates and MBF-deposited GaAs(100) buffer layers are considered. As a comparison to the study of Au-GaAs(100) interfaces, BEEM imaging is performed on Au-Si(100) interfaces. It is noted that Au-GaAs(100) interface formation is relatively insensitive to the effects of substrate surface condition and substrate bulk defect density, and that the combination of BEEM imaging and BEEM spectroscopy indicates that the heterogeneous interface defects are the result of diffusion between the Schottky barrier electrodes.

Hecht, M. H.↗
DOE OSTI2024

Unsupervised learning-enabled pulsed infrared thermographic microscopy of subsurface defects in stainless steel

Metallic structures produced with laser powder bed fusion (LPBF) additive manufacturing method (AM) frequently contain microscopic porosity defects, with typical approximate size distribution from one to 100 microns. Presence of such defects could lead to premature failure of the structure. In principle, structural integrity assessment of LPBF metals can be accomplished with nondestructive evaluation (NDE). Pulsed infrared thermography (PIT) is a non-contact, one-sided NDE method that allows for imaging of internal defects in arbitrary size and shape metallic structures using heat transfer. PIT imaging is performed using compact instrumentation consisting of a flash lamp for deposition of a heat pulse, and a fast frame infrared (IR) camera for measuring surface temperature transients. However, limitations of imaging resolution with PIT include blurring due to heat diffusion, sensitivity limit of the IR camera. We demonstrate enhancement of PIT imaging capability with unsupervised learning (UL), which enables PIT microscopy of subsurface defects in high strength corrosion resistant stainless steel 316 alloy. PIT images were processed with UL spatial–temporal separation-based clustering segmentation (STSCS) algorithm, refined by morphology image processing methods to enhance visibility of defects. The STSCS algorithm starts with wavelet decomposition to spatially de-noise thermograms, followed by UL principal component analysis (PCA), fine-tuning optimization, and neural learning-based independent component analysis (ICA) algorithms to temporally compress de-noised thermograms. The compressed thermograms were further processed with UL-based graph thresholding K-means clustering algorithm for defects segmentation. The STSCS algorithm also includes online learning feature for efficient re-training of the model with new data. For this study, metallic specimens with calibrated microscopic flat bottom hole defects, with diameters in the range from 203 to 76 µm, were produced using electro discharge machining (EDM) drilling. While the raw thermograms do not show any material defects, using STSCS algorithm to process PIT images reveals defects as small as 101 µm in diameter. To the best of our knowledge, this is the smallest reported size of a sub-surface defect in a metal imaged with PIT, which demonstrates the PIT capability of detecting defects in the size range relevant to quality control requirements of LPBF-printed high-strength metals.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Multimodal microscopy of extended defects in β-Ga 2 O 3 (010) EFG crystals

Beta-phase gallium oxide (β-Ga 2 O 3 ) has attracted attention in recent years as a potentially low cost, large area substrate and active layer material for high power, high temperature power electronics and sensing devices. However, growth of β-Ga 2 O 3 crystals is complicated by easily activated (100) and (001) cleavage planes, the presence of low angle grain boundaries (LAGBs) and twins, and the potential formation of polycrystalline grains. In this study, β-Ga 2 O 3 crystals were grown by the edge-defined film-fed growth technique with an (010) principal face. Two crystals with apparently randomly formed high angle grain boundaries (HAGBs) were selected and analyzed by electron backscatter diffraction, electron channeling contrast imaging, and cathodoluminescence to investigate the nature of the LAGBs and the source of the HAGB formation. It was discovered that planar LAGBs lying parallel to the (010) plane exist in the region immediately preceding the start of an HAGB. Increased misorientation across the LAGB was observed, approaching the initiation of a new grain. We present multimodal microscopy characterization, correlating misorientation and variation in optoelectronic properties with LAGBs and the associated dislocations.

14 SOLAR ENERGY↗
DOE OSTI2024

Optical tuning of the diamond Fermi level measured by correlated scanning probe microscopy and quantum defect spectroscopy

Quantum technologies based on quantum point defects in crystals require control over the defect charge state. Here we tune the charge state of shallow nitrogen-vacancy and silicon-vacancy centers by locally oxidizing a hydrogenated surface with moderate optical excitation and simultaneous spectral monitoring. The loss of conductivity and change in work function due to oxidation are measured in atmosphere using conductive atomic force microscopy and Kelvin probe force microscopy (KPFM). We correlate these scanning probe measurements with optical spectroscopy of the nitrogen-vacancy and silicon-vacancy centers created via implantation 15–25 nm beneath the diamond surface and annealing. The observed charge state of the defects as a function of optical exposure demonstrates that laser oxidation provides a way to precisely tune the Fermi level over a range of at least 2.00 eV. We also observe a significantly larger oxidation rate for implanted surfaces compared to unimplanted surfaces under ambient conditions. Here, combined with knowledge of the electron affinity of a surface, these results suggest KPFM is a powerful, high-spatial-resolution technique to advance surface Fermi level engineering for charge stabilization of quantum defects.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Probing polarization dynamics at specific domain configurations: Computer-vision based automated experiment in piezoresponse force microscopy

Topological defects in ferroelectric materials have attracted much attention due to the emergence of conductive, ferroic, and magnetic functionalities. However, many topological configurations dynamically evolve during the switching processes, making them a challenge to characterize via traditional techniques. Here, we implement an automated experimentation approach for the exploration of functional properties in BiFeO 3 thin films. Specifically, we visualize the ferroelectric domain structures via single frequency piezoresponse force microscopy and implement a computer vision-based algorithm to discover features of interest at which spectroscopic measurements are taken. Subsequently, we employ dimensionality reduction techniques to reveal characteristic polarization behaviors at these features. This approach can be extended to other spectroscopies and modalities to probe only specific features of interest, ultimately enabling dynamical processes in ferroelectrics to be studied.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Magnetic states of atomic vacancies in graphite probed by scanning tunneling microscopy

Intrinsic defects in graphitic materials, like vacancies and edges, have been expected to possess magnetic states from the many-body interaction of localized electrons. However, charge screening from graphite bulk carriers significantly reduces the localization effect and hinders the observation of those magnetic states. Here, we use an ultra-low-temperature scanning tunneling microscope with a high magnetic field to observe the magnetic states of atomic vacancies in graphite generated by ion sputtering. Scanning tunneling spectroscopy reveals localized states at the vacancies, which exhibit splitting at a certain magnetic field whose separation increases with the field strength. The transition is well described by the “Anderson model,” which describes the emergence of localized magnetic states inside the metallic reservoir through electron–electron interaction. The interaction strength is estimated to be between 1 meV and 3 meV, which is supported by the density functional theory calculation. The observation provides an important foundation for application of intrinsic defects to carbon-based spintronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Scanning probe spectroscopy of sulfur vacancies and MoS 2 monolayers in side-contacted van der Waals heterostructures

We investigate the interplay between vertical tunneling and lateral transport phenomena in electrically contacted van der Waals heterostructures made from monolayer MoS 2 , hBN, and graphene. We compare data taken by low-temperature scanning tunneling spectroscopy to results from room-temperature conductive atomic force spectroscopy on monolayer MoS 2 with sulfur vacancies and with varying hBN layers. We show that for thick hBN barrier layers, where tunneling currents into the conductive substrate are suppressed, a side-contact still enables addressing the defect states in the scanning tunneling microscopy via the lateral current flow. Few-layer hBN realizes an intermediate regime in which the competition between vertical tunneling and lateral transport needs to be considered. The latter is relevant for device structures with both a thin tunneling barrier and a side-contact to the semiconducting layers.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Exploring Charged Defects in Ferroelectrics by the Switching Spectroscopy Piezoresponse Force Microscopy

Monitoring the charged defect concentration at the nanoscale is of critical importance for both the fundamental science and applications of ferroelectrics. However, up-to-date, high-resolution study methods for the investigation of structural defects, such as transmission electron microscopy, X-ray tomography, etc., are expensive and demand complicated sample preparation. Here, with an example of the lanthanum-doped bismuth ferrite ceramics, a novel method is proposed based on the switching spectroscopy piezoresponse force microscopy (SSPFM) that allows probing the electric potential from buried subsurface charged defects in the ferroelectric materials with a nanometer-scale spatial resolution. When compared with the composition-sensitive methods, such as neutron diffraction, X-ray photoelectron spectroscopy, and local time-of-flight secondary ion mass spectrometry, the SSPFM sensitivity to the variation of the electric potential from the charged defects is shown to be equivalent to less than 0.3 at% of the defect concentration. Additionally, the possibility to locally evaluate dynamics of the polarization screening caused by the charged defects is demonstrated, which is of significant interest for further understanding defect-mediated processes in ferroelectrics.

42 ENGINEERING↗
DOE OSTI2025

Defect Complexes in CrSBr Revealed Through Electron Microscopy and Deep Learning

Atomic defects underpin the properties of van der Waals materials, and their understanding is essential for advancing quantum and energy technologies. Scanning transmission electron microscopy is a powerful tool for defect identification in atomically thin materials, and extending it to multilayer and beam-sensitive materials would accelerate their exploration. Here, we establish a comprehensive defect library in a bilayer of the magnetic quasi-1D semiconductor CrSBr by combining atomic-resolution imaging, deep learning, and calculations. We apply a custom-developed machine learning work flow to detect, classify, and average point vacancy defects. This classification enables us to uncover several distinct Cr interstitial defect complexes, combined Cr and Br vacancy defect complexes, and lines of vacancy defects that extend over many unit cells. We show that their occurrence is in agreement with our computed structures and binding energy densities, reflecting the intriguing layer interlocked crystal structure of CrSBr. Our ab initio calculations show that the interstitial defect complexes give rise to highly localized electronic states. These states are of particular interest due to the reduced electronic dimensionality and magnetic properties of CrSBr and are, furthermore, predicted to be optically active. Our results broaden the scope of defect studies in challenging materials and reveal new defect types in bilayer CrSBr that can be extrapolated to the bulk and to over 20 materials belonging to the same FeOCl structural family.

deep learning↗
DOE OSTI2020

Characterizing Dislocation Defects in Dark Field X-ray Microscopy Images of Bulk Aluminum

Material defects play a large role in material response under shock loading, yet the process of how these defects initiate, propagate, and annihilate is not well understood. Using a newly developed diagnostic, dark field X-ray microscopy (DFXM), we can now visualize the behavior of dislocation defects in materials at the mesoscale under varying conditions. Using data from the European Synchrotron Radiation Facility, we apply a variety of image processing techniques to capture relevant features to locate and characterize size and orientation of dislocation defects in bulk aluminum DFXM images. Beyond simple visualization, this analysis drives statistical characterization of the defects and their dynamic response to further improve the relevant physics models.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗