Search NASA⌕ Search

SEARCH · Search NASA

Results for “delay variations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

A test of water vapor radiometer-based troposphere calibration using VLBI observations on a 21-kilometer baseline

Simultaneous very long baseline interferometry (VLBI) and water vapor radiometer (WVR) measurements on a 21 km baseline showed that calibration by WVRs removed a significant fraction of the effect of tropospheric delay fluctuations for these experiments. From comparison of the residual delay variations within scans and between scans, the total tropospheric contribution t the delay residuals for each of the three 5 to 20 hour sessions was estimated as 1, 17, and 10%, with the first value being uncertain. The observed improvement in rms residual delay from WVR calibration during these three sessions was 4, 16, and 2%, respectively. The improvement is consistent with the estimated 2 to 3 mm path delay precision of current WVRs. The VLBI measurements, of natural radio sources, were conducted in April and May 1993 at Goldstone, California. Dual-frequency (2.3 and 8.4 GHz) observations were employed to remove the effects of charged particles from the data. Measurements with co-pointed WVRs, located within 50 m of the axis of each antenna, were performed to test the ability of the WVRs to calibrate line-of-sight path delays. Factors that made WVR performance assessment difficult included (1) the fact that the level of tropospheric fluctuations was smaller than is typical for Goldstone during these experiments and (2) VLBI delay variations on longer time scales (i.e., over multiple scans) contained uncalibrated instrumental effects (probably a result of slow temperature variations in the VLBI hardware) that were larger than the tropospheric effects.

Linfield, R. P.↗
NASA NTRS1996

A Demonstration of Precise Calibration of Tropospheric Delay Fluctuations with Water Vapor Radiometers

The ability of water vapor radiometers (WVRs) to calibrate changes in tropospheric delay was demonstrated during very long baseline radio interferometer (VLBI) observations at Goldstone, California. WVR measurements reduced the observed VLBI delay variations over a 13 hr period by a factor of approx. = 2.5. When applied to shorter time scales, a approx. = 50% reduction in 100-700 s delay variations was achieved during conditions of high tropospheric activity. Thermal WVR noise precluded calibration of short time scale delay fluctuations during quiet tropospheric conditions.

Teitelbaum, L. P.↗
NASA NTRS1982

Variations in propagation delay times for line ten (TV) based time transfers

Variation in the propagation delay for a 30 km TV (Line Ten) radio link was evaluated for a series of 30 independent measurements. Time marks from TV Channel 5 WTTG in Washington, D.C. were simultaneously measured at the Johns Hopkins University Applied Physics Laboratory and at the United States Naval Observatory against each stations' local cesium standard clocks. Differences in the stations' cesium clocks were determined by portable cesium clock transfers. Thirty independent timing determinations were made. The root mean square deviation in the propagation delay calculated from the timing determinations was 11 ns. The variations seen in the propagation delays are believed to be caused by environmental factors and by errors in the portable clock timing measurements. In correlating the propagation delay variations with local weather conditions, only a moderate dependence on air temperature and absolute humidity was found.

Chiu, M. C.↗
NASA NTRS1981

Precise T and F intercomparison via VLF phase measurements

Continuous phase recording of the 16kHz transmission from GBR (UK) are being made and published midday phase data of GBR are received regularly from laboratories in the US, FGR, and UK. The local time scale (UTC, India), at the National Physical Laboratory in New Delhi, and those at the foreign laboratories are intercompared using the VLF phase data. A major factor which limits the accuracy of long term comparison is the seasonal variation in the VLF over delay over long paths. By taking into account the seasonal delay variations in a semiempirical way, the accuracy of time and frequency comparisons can be improved. Over a one year period, accuracy of a few parts in 10 to the 14th power in frequency and 1 to 2 micron sec in time were obtained. The relative frequency offset difference between UTC, (India) and UTC (PTB, Germany) of (7.0 + or - 0.1) x 10 to the -13 power agrees well with that obtained in a satellite experiment.

Gupta, A. S.↗
NASA NTRS2000

Postural control model interpretation of stabilogram diffusion analysis

Collins and De Luca [Collins JJ. De Luca CJ (1993) Exp Brain Res 95: 308-318] introduced a new method known as stabilogram diffusion analysis that provides a quantitative statistical measure of the apparently random variations of center-of-pressure (COP) trajectories recorded during quiet upright stance in humans. This analysis generates a stabilogram diffusion function (SDF) that summarizes the mean square COP displacement as a function of the time interval between COP comparisons. SDFs have a characteristic two-part form that suggests the presence of two different control regimes: a short-term open-loop control behavior and a longer-term closed-loop behavior. This paper demonstrates that a very simple closed-loop control model of upright stance can generate realistic SDFs. The model consists of an inverted pendulum body with torque applied at the ankle joint. This torque includes a random disturbance torque and a control torque. The control torque is a function of the deviation (error signal) between the desired upright body position and the actual body position, and is generated in proportion to the error signal, the derivative of the error signal, and the integral of the error signal [i.e. a proportional, integral and derivative (PID) neural controller]. The control torque is applied with a time delay representing conduction, processing, and muscle activation delays. Variations in the PID parameters and the time delay generate variations in SDFs that mimic real experimental SDFs. This model analysis allows one to interpret experimentally observed changes in SDFs in terms of variations in neural controller and time delay parameters rather than in terms of open-loop versus closed-loop behavior.

NASA Program Biomedical Research and Countermeasur↗
NASA NTRS1987

A study of the effect of group delay distortion on an SMSK satellite communications channel

The effects of group delay distortion on an SMSK satellite communications channel have been investigated. Software and hardware simulations have been used to determine the effects of channel group delay variations with frequency on the bit error rate for a 220 Mbps SMSK channel. These simulations indicate that group delay distortions can significantly degrade the bit error rate performance. The severity of the degradation is dependent on the amount, type, and spectral location of the group delay distortion.

Kerczewski, Robert J.↗
NASA NTRS1990

Cable delay compensator for microwave signal distribution over optical fibers

The basic principles of microwave fiber-optic systems are outlined with emphasis on fiber-optic cable delay compensators (CDC). Degradation of frequency and phase stability is considered, and it is pointed out that the long-term stability of a fiber-optic link is degraded by group delay variations due to temperature fluctuations in the optical fiber and low-frequency noise characteristics of the laser. A CDC employing a voltage-controlled oscillator to correct for phase variations in the optical fiber is presented, and the static as well as dynamic closed-loop analyses of the fiber-optic CDC are discussed. A constructed narrow-band fiber-optic CDC is shown to reduce phase variations caused by temperature fluctuations by a factor of 400. A wide-band CDC utilizing a temperature-controlled coil of fiber to compensate for phase delay is also proposed.

Primas, Lori E.↗
NASA NTRS1978

GEOS-3 coherent C-band tracking data reduction and analysis

The availability of a coherent C-Band transponder on an orbiting vehicle has permitted the development of calibration techniques for C-Band radars. Prior coherent tracking was limited to test vehicles in powered flight or skin tracking of orbiting spacecraft. The pulse Doppler range rate data available concurrently and independently with normal range and angle data provides an extremely useful data set for assessing the internal consistency of the radars measurements, particularly when coupled with a trajectory well constrained by orbit dynamics. In order to further assess the precision of the range rate data, a technique was developed to numerically integrate the rate measurements into a pseudo-range data set showing extremely low noise and high sensitivity to systematic radar errors. Evaluation of integrated range data led to improvements in calibration of both the rate and conventional range data. In particular, proper evaluation of the very sensitive integrated ranges required the development of a processing correction for beacon delay variation with signal strength, a significant error in the conventional ranging data.

Krabill, W. B.↗
NASA NTRS1980

Performance analysis and simulation of the SPS reference phase control system

The major elements required in the operation of an SPS which employs retrodirectivity as a means of pointing the beam to Earth include the spacetenna, the rectenna, and the pilot signal transmitter. The phase control system is faced with several problems: (1) path delay variations due to imperfect SPS circular orbits; (2) ionospheric effects; (3) initial phase beam forming; (4) beam pointing; (5) beam safing; (6) high power phase noise effects; and (7) interference. The use of SOLARISM, a computer program to select pilot signal parameters and evaluate SPS performance is described.

Lindsey, W. C.↗
NASA NTRS1989

A low-loss linear analog phase modulator for 8415 MHz transponder application

A breadboard single-section low-loss analog phase modulator with good thermal stability for a spacecraft transponder application has been analyzed, fabricated, and evaluated. A linear phase shift of 70 degrees with a linearity tolerance of plus or minus 7 percent was measured for this modulator from 8257 to 8634 MHz over the temperature range -20 C to 75 C. The measured insertion loss and the static delay variation with temperature were within 2 plus or minus 0.3 dB and 0.16 ps/C, respectively. Four sections will be cascaded to provide the X-band (8415 MHz) phase modulator. The generic modulator design can also be utilized at 7950 to 8075 MHz followed by X4 multiplication to provide modulation of a Ka-band downlink signal.

Mysoor, N.↗
NASA NTRS1988

The GPS based precision orbit determination experiment on TOPEX

The objectives of the GPS-based precision orbit determination (POD) experiment on TOPEX are discussed. Problems facing this experiment include the careful design of all network receivers to control uncalibrated systematic group-delay biases and delay variations between channels, and the careful design of both the GPS-antenna-TOPEX satellite interface and the ground antennas to mimimize multipath. Questions of reference frames, geoid recovery, and the application of innovative orbit determination strategies must also be addressed.

Melbourne, William G.↗
NASA NTRS1991

Design and status of the RF-digitizer integrated circuit

An integrated circuit currently under development samples a bandpass-limited signal at a radio frequency in quadrature and then performs a simple sum-and-dump operation in order to filter and lower the rate of the samples. Downconversion to baseband is carried out by the sampling step itself through the aliasing effect of an appropriately selected subharmonic sampling frequency. Two complete RF digitizer circuits with these functions will be implemented with analog and digital elements on one GaAs substrate. An input signal, with a carrier frequency as high as 8 GHz, can be sampled at a rate as high as 600 Msamples/sec for each quadrature component. The initial version of the chip will sign-sample (1-bit) the input RF signal. The chip will contain a synthesizer to generate a sample frequency that is a selectable integer multiple of an input reference frequency. In addition to the usual advantages of compactness and reliability associated with integrated circuits, the single chip will replace several steps required by standard analog downconversion. Furthermore, when a very high initial sample rate is selected, the presampling analog filters can be given very large bandwidths, thereby greatly reducing phase and delay instabilities typically introduced by such filters, as well as phase and delay variation due to Doppler changes.

Rayhrer, B.↗
NASA NTRS1991

Design and analysis of a low-loss linear analog phase modulator for deep space spacecraft X-band transponder applications

This article summarizes the design concepts, analyses, and development of an X-band (8145 MHz) transponder low-loss linear phase modulator for deep space spacecraft applications. A single-section breadboard circulator-coupled reflection phase modulator has been analyzed, fabricated, and evaluated. A linear phase deviation of 92 deg with a linearity tolerance of +/- 8 percent was measured for this modulator from 8257 MHz to 8634 MHz over the temperature range -20 to 75 C. The measured insertion loss and the static delay variation with temperature were 2 +/- 0.3 dB and 0.16 psec/ C, respectively. Based on this design, cascaded sections have been modeled, and simulations were performed to provide an X-band deep space transponder (DST) phase modulator with +/- 2.5 radians (+/- 143 deg) of peak phase deviation to accommodate downlink signal modulation with composite telemetry data and ranging, with a deviation linearity tolerance of +/- 8 percent and insertion loss of less than 10 +/- 0.5 dB. A two-section phase modulator using constant gamma hyperabrupt varactors and an efficient modulator driver circuit was breadboarded. The measured results satisfy the DST phase-modulator requirements and show excellent agreement with the predicted results.

Mysoor, N. R.↗
NASA NTRS1995

Accuracy of wet troposphere radio path delay estimated from infrared emission

Several radio science applications require determination of the excess radio-propagation path delay caused by the Earth's atmosphere. These include very long baseline interferometry, spacecraft tracking, and potentially, detection of gravitational waves utilizing a link to a distant interplanetary spacecraft. At Ka band, the major source of variability of path delay is the fluctuations in the moisture content of the troposphere. The path delay characterization requirements for a planned gravitational wave experiment are novel and challenging. the error contribution to the phase observations due to path delay variation must be reduced by nearly two orders of magnitude over that occurring naturally on time scales of 100 to 10,000 seconds. Current approaches relying on microwave water vapor radiometry with ancillary data can deliver one order of magnitude calibration of these fluctuations, and more advanced systems are under development within the 2001-2002 time frame of the Cassini Mission to Saturn. The current work evaluates the potential for an alternative observational approach, using a ground-based Fourier transform spectrometer.

Parker, J. W.↗
NASA NTRS1996

Space-Based Information Infrastructure Architecture for Broadband Services

This study addressed four tasks: (1) identify satellite-addressable information infrastructure markets; (2) perform network analysis for space-based information infrastructure; (3) develop conceptual architectures; and (4) economic assessment of architectures. The report concludes that satellites will have a major role in the national and global information infrastructure, requiring seamless integration between terrestrial and satellite networks. The proposed LEO, MEO, and GEO satellite systems have satellite characteristics that vary widely. They include delay, delay variations, poorer link quality and beam/satellite handover. The barriers against seamless interoperability between satellite and terrestrial networks are discussed. These barriers are the lack of compatible parameters, standards and protocols, which are presently being evaluated and reduced.

Price, Kent M.↗
NASA NTRS1999

Traffic Management in ATM Networks Over Satellite Links

This report presents a survey of the traffic management Issues in the design and implementation of satellite Asynchronous Transfer Mode (ATM) networks. The report focuses on the efficient transport of Transmission Control Protocol (TCP) traffic over satellite ATM. First, a reference satellite ATM network architecture is presented along with an overview of the service categories available in ATM networks. A delay model for satellite networks and the major components of delay and delay variation are described. A survey of design options for TCP over Unspecified Bit Rate (UBR), Guaranteed Frame Rate (GFR) and Available Bit Rate (ABR) services in ATM is presented. The main focus is on traffic management issues. Several recommendations on the design options for efficiently carrying data services over satellite ATM networks are presented. Most of the results are based on experiments performed on Geosynchronous (GEO) latencies. Some results for Low Earth Orbits (LEO) and Medium Earth Orbit (MEO) latencies are also provided.

Goyal, Rohit↗