Experimental Detonation Velocities and Induction Distances in Hydrogen- Nitrous Oxide Mixtures
Experimental detonation velocities and induction distances in hydrogen-nitrous oxide mixtures
NITROGEN OXIDE↗
SEARCH · Search NASA
Results for “detonation velocity”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Determination of detonation wave velocities.
Detonation wave velocity measurement using piezoelectric coaxial transducer pins and solid state pulse amplifiers
Bowen, J. R.↗
Start/stop switches for testing detonation velocity of explosives
Printed-circuit process produces ordnance-initiated start/stop switches. Method is faster and less costly than fabriction by hand, and produces switches of uniform quality.
Wise, J. P.↗
An Investigation Into Some Important Aspects of Droplet Breakup/Vaporization Behavior Caused By a Gas Flow (Both Nonreacting & Detonative Combustion) in a Shock Tube
As a part of the rotating detonation engine (RDE) technology enablement project at NASA Glenn Research Center (GRC), an effort was undertaken to extend our current computational capabilities of OpenNCC in some important ways with the implementation of a modeling approach to account for the droplet breakup caused by a shock-induced gas motion, & a vaporization model valid over a wide range of pressure conditions encountered in multiphase detonation. With the modified code, a study was undertaken to investigate the individual droplet behavior followed by the passage of a shock front. The study is carried out by tracking a sparse group of droplets to gain some understanding of shock induced droplet behavior under various shock strengths & fuel injector conditions. The study also looks into the effect of randomization involved in determining the droplet breakup outcomes. Over a wide range of sub-critical conditions examined, larger droplets are observed to undergo significant changes in droplet behavior following their breakup. However, smaller droplets (10 µm or less ) remain unaffected by any shock induced breakup. In a follow-on work, we investigated the impact of shock and droplet interaction in a detonation study involving both gaseous as well as gas/liquid (droplet clouds) fuel/air stoichiometric mixtures in a simple 3D shock-tube configuration. The droplet clouds are made up of different initial droplet sizes of either 6, 10, or 30 µm. We also investigated the individual droplet behavior followed by the passage of a detonation front. The results represent conditions that lead to both overdriven and C-J (ChapmanJouguet) detonations. Under both test conditions, most of the droplet vaporization is completed within a short distance (duration) behind the detonation front & well within the region of complete combustion observed in a corresponding equivalent gas-phase fuel/air mixture. The impact of the shock-induced droplet breakup is found to be significant in the calculations involving the 30-µm droplets. Subsequent to the breakup, the drop sizes vary from 1 to 10 µm. Another factor that contributed to the observed rapid vaporization is the result of vaporization taking place under supercritical conditions. The overall detonation properties of various droplet clouds (made up of different initial sizes) are similar to those observed in a corresponding gaseous fuel/air mixture. In the calculation involving a gaseous fuel, the calculated C-J detonation velocity is 1822 m/s involving Jet-A/air and φ = 1. In the overdriven detonation, it is 2044 m/s. In the calculations involving droplet clouds, the corresponding detonation velocities are lower. The impact of increased droplet size is primarily seen in a higher reduction in the detonation velocity.
shock/droplet interaction↗
Hydrazine vapor detonations
The detonation velocity and cell widths for hydrazine decomposition were measured over a wide range of temperatures and pressures. The detonation velocity in pure hydrazine was within 5 percent of the calculated C-J velocity. The detonation cell width measurements were interpreted using the Zeldovich-Doering-von Neumann model with a detailed reaction mechanism for hydrazine decomposition. Excellent agreement with experimental data for pure hydrazine was obtained using the empirical relation that detonation cell width was equal to 29 times the kinetically calculated reaction zone length.
Pedley, M. D.↗
Age Life Evaluation of Space Shuttle Crew Escape System Pyrotechnic Components Loaded with Hexanitrostilbene (HNS)
Determining deterioration characteristics of the Space Shuttle crew escape system pyrotechnic components loaded with hexanitrostilbene would enable us to establish a hardware life-limit for these items, so we could better plan our equipment use and, possibly, extend the useful life of the hardware. We subjected components to accelerated-age environments to determine degradation characteristics and established a hardware life-limit based upon observed and calculated trends. We extracted samples using manufacturing lots currently installed in the Space Shuttle crew escape system and from other NASA programs. Hardware included in the study consisted of various forms and ages of mild detonating fuse, linear shaped charge, and flexible confined detonating cord. The hardware types were segregated into 5 groups. One was subjected to detonation velocity testing for a baseline. Two were first subjected to prolonged 155 F heat exposure, and the other two were first subjected to 255 F, before undergoing detonation velocity testing and/or chromatography analysis. Test results showed no measurable changes in performance to allow a prediction of an end of life given the storage and elevated temperature environments the hardware experiences. Given the lack of a definitive performance trend, coupled with previous tests on post-flight Space Shuttle hardware showing no significant changes in chemical purity or detonation velocity, we recommend a safe increase in the useful life of the hardware to 20 years, from the current maximum limits of 10 and 15 years, depending on the hardware.
Hoffman, William C., III↗
The effect of boundaries on the velocity deficit and the limit of gaseous detonations
Boundary effects on gaseous detonation velocity deficit and limit using approximation into boundary layer equations, comparing to experimental data
Tsuge, S.↗
Thermodynamic Calculations of Hydrogen-Oxygen Detonation Parameters for Various Initial Pressures
Composition, temperature, pressure and density behind a stable detonation wave and its propagation rate have been calculated for seven hydrogen-oxygen mixture at 1, 5, 25 and 100 atm initial pressure, and at an initial temperature of 40C. For stoichiometric mixtures that calculations also include an initial temperature of 200C. According to these calculations the detonation velocities of hydrogen-oxygen mixtures increase with increasing initial pressure, but decrease slightly when the initial temperature is raised from 40 to 200 C. The calculated detonation velocities agree satisfactorily with values determined experimentally. These values will be published in the near future.
Bollinger, Loren E.↗
Development of a Gas-Fed Pulse Detonation Research Engine
In response to the growing need for empirical data on pulse detonation engine performance and operation, NASA Marshall Space Flight Center has developed and placed into operation a low-cost gas-fed pulse detonation research engine. The guiding design strategy was to achieve a simple and flexible research apparatus, which was inexpensive to build and operate. As such, the engine was designed to operate as a heat sink device, and testing was limited to burst-mode operation with run durations of a few seconds. Wherever possible, maximum use was made of standard off-the-shelf industrial or automotive components. The 5-cm diameter primary tube is about 90-cm long and has been outfitted with a multitude of sensor and optical ports. The primary tube is fed by a coaxial injector through an initiator tube, which is inserted directly into the injector head face. Four auxiliary coaxial injectors are also integrated into the injector head assembly. All propellant flow is controlled with industrial solenoid valves. An automotive electronic ignition system was adapted for use, and spark plugs are mounted in both tubes so that a variety of ignition schemes can be examined. A microprocessor-based fiber-optic engine control system was developed to provide precise control over valve and ignition timing. Initial shakedown testing with hydrogen/oxygen mixtures verified the need for Schelkin spirals in both the initiator and primary tubes to ensure rapid development of the detonation wave. Measured pressure wave time-of-flight indicated detonation velocities of 2.4 km/sec and 2.2 km/sec in the initiator and primary tubes, respectively. These values implied a fuel-lean mixture corresponding to an H2 volume fraction near 0.5. The axial distribution for the detonation velocity was found to be essentially constant along the primary tube. Time-resolved thrust profiles were also acquired for both underfilled and overfilled tube conditions. These profiles are consistent with previous time-resolved measurements on single-cycle tubes where the thrust is found to peak as the detonation wave exits the tube, and decay as the tube blows down.
Litchford, Ron J.↗
Detonability of hydrocarbon fuels in air
Studies were conducted of the detonation of gas-phase mixtures of n-hexane and JP-4, with oxidizers as varied as air and pure oxygen, measuring detonation velocities and cell sizes as a function of stoichiometry and diluent concentration. The induction length of a one-dimensional Zeldovich-von Neumann-Doering detonation was calculated on the basis of a theoretical model that employed the reaction kinetics of the hydrocarbon fuels used. Critical energy and critical tube diameter are compared for a relative measure of the heavy hydrocarbon fuels studied; detonation sensitivity appears to increase slightly with increasing carbon number.
Beeson, H. D.↗
Explosive Welding of Aluminum, Titanium and Zirconium to Copper Sheet Metal
The main material properties affecting the explosive weldability of a certain metal combination are the yield strength, the ductility, the density and the sonic velocity of the two metals. Successful welding of the metal combination depends mainly on the correct choice of the explosive welding parameters; i.e., the stand off distance, the weight of the explosive charge relative to the weight of the flyer plate and the detonation velocity of the explosive. Based on the measured and the handbook values of the properties of interest, the explosive welding parameters were calculated and the arrangements for the explosive welding of the Al alloy 6061-T6, titanium and zirconium to OFHC copper were determined. The relatively small sheet metal thickness (1/8") and the fact that the thickness of the explosive layer must exceed a certain minimum value were considered during the determination of the explosive welding conditions. The results of the metallographic investigations and the measurements of the shear strength at the interface demonstrate the usefulness of these calculations to minimize the number of experimental trials.
Hegazy, A. A.↗
Analysis and demonstration of a Scramaccelerator system
The Scramaccelerator, a novel type of supersonic-combustion, tube-based launcher has been developed that can accelerate almost any mass to velocities of 3 to over 7 km/sec. This paper describes the technology demonstration of the concept by firing 120-g projectiles into a 38 mm barrel at 2.8 to 3.2 km/sec. The results from the technology demonstration are presented along with calculated performance of the demonstration tests. Critical test issues discussed include sabot separation, venting requirements, and test performance. The results, obtained during testing indicate projectile accelerations were achieved of approximately 5000 g. Hence, these tests demonstrate successful Scramaccelerator operation and acceleration at approximately 1.95 times the Chapman Jouguet detonation velocity, far greater than the 1.15 to 1.3 times previously demonstrated. In addition, the tests demonstrate hypersonic propulsion at Mach numbers above 8, acceleration at greater than 3 km/s, and system integration technology sufficient to accomplish this success.
Humphrey, Joseph W.↗
Initiation of insensitive explosives by laser energy
Instantaneous longitudinal detonations were observed in confined columns of pentaerythritol tetranitrate (PETN), cyclotrimethylene trinitramine (RDX), and tetryl when these materials were pulsed with light energy from a focused Q-switch ruby laser. The laser energy ranged from 0.5 to 4.2 J with a pulse width of 25 ns. Enhancement of the ignition mechanism is hypothesized when a 100-nm (1000-A) thick aluminum film is vacuum-deposited on the explosive side of the window. Upon irradiation from the laser, a shock is generated at the aluminum explosive interface. Steady state detonations can be reached in less than 0.5 microseconds with less than 10% variation in detonation velocity for PETN and RDX.
Menichelli, V. J.↗
Detonation of insensitive high explosives by a Q-switched ruby laser.
Immediate longitudinal detonations have been observed in confined small-diameter columns of PETN, RDX, and tetryl by using a focused Q-switched ruby laser. The energy ranged from 0.8 to 4.0 J in a pulse width of 25 nsec. A 1000-A-thick aluminum film deposited on a glass window was used to generate a shock wave at the window-explosive interface when irradiated by the laser. In some cases, steady-state detonations were reached in less than .5 microsec with less than 10% variation in the detonation velocity.
Yang, L. C.↗
Direct laser initiation of insensitive explosives.
Instantaneous longitudinal detonations have been observed in confined columns of PETN, RDX, and tetryl when pulsed with light energy from a focused Q-switched ruby laser. The laser energy ranged from 0.5 to 4.2 J with a pulse width of 25 nsec. Enhancement of the ignition mechanism is hypothesized when a 1000 A thick aluminum film is vacuum deposited on the explosive side of the window. Upon irradiation from the laser, a shock is generated at the aluminum-explosive interface. Steady-state detonations can be reached in less than 0.5 microsec with less than 10% variation in detonation velocity for PETN and RDX.
Menichelli, V. J.↗
Explosives for Lunar Seismic Profiling Experiment (LSPE)
Explosive charges of various sizes were investigated for use in lunar seismic studies. Program logistics, and the specifications for procurement of bulk explosives are described. The differential analysis, thermal properties, and detonation velocity measurements on HNS/Teflon 7C 90/10 are reported along with the field tests of the hardware. It is concluded that nearly all large explosive charges crack after fabrication, from aging or thermal shock. The cracks do not affect the safety, or reliability of the explosives.
Source record↗
Experiments on hypersonic ramjet propulsion cycles using a ram accelerator
Work on hypersonic propulsion research using a ram accelerator is presented. Several different ram accelerator propulsive cycles have been experimentally demonstrated over the Mach number range of 3 to 8.5. The subsonic, thermally choked combustion mode has accelerated projectiles to near the Chapman-Jouguet (C-J) detonation velocity within many different propellant mixtures. In the transdetonative velocity regime (85 to 115 percent of C-J speed), projectiles have established a propulsive cycle which allows them to transition smoothly from subdetonative to superdetonative velocities. Luminosity data indicate that the combustion process moves forward onto the projectile body as it approaches the C-J speed. In the superdetonative velocity range, the projectiles accelerate while always traveling faster than the C-J velocity. Ram accelerator projectiles operating continuously through these velocity regimes generate distinctive hypersonic phenomena which can be studied very effectively in the laboratory. These results would be very useful for validating sophisticated CFD computer codes and in collecting engineering data for potential airbreathing hypersonic propulsive systems.
Chew, G.↗
A Multiphase Equation of State for Hydrazine and Monomethylhydrazine
The objective of this work was to obtain a validated equation of state for hydrazine and monomethylhydrazine (MMH) and use this equation to calculate thermodynamic properties. The approach was based on using both reliable critical property values and a value of the acentric factor in the Soave Redlich Kwong and the Peng Robinson model equations of state. These equations were validated by comparing calculated molar volumes for phase equilibrium with published experimental values and comparing calculated vapor pressures with published experimental values over the temperature range appropriate for the corresponding state equations. The equation of state giving the best results was used to calculate enthalpy and entropy departure functions and fugacity values. Additional thermodynamic property calculations were performed to produce partial Mollier diagrams and thermodynamic properties containing internal energy, enthalpy, and entropy values for hydrazine and MMH. The analyses of systems in which either adiabatic or near-adiabatic compression of liquid or vapor hydrazine or low velocity detonations occur require a validated equation of state for representing occurring molar volumes and for energy calculations. Other calculations for thermodynamic properties of hydrazine are available, but the values are for a strict ideal gas state. This work characterized destructive events using hydrazine by calculating for isentropic compression temperatures. The final temperatures were calculated and compared using the ideal and real gas fluid equations of state.
Barragan, Michelle↗