Cooling of gas turbine IV : calculated temperature distribution in the trailing part of a turbine blade using direct liquid cooling
Explore the source record for details and available documents.
Brown, W Byron↗
SEARCH · Search NASA
Results for “direct liquid cooling”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Cooling of Gas Turbines, IV - Calculated Temperature Distribution in the Trailing Part of a Turbine Blade Using Direct Liquid Cooling
A theoretical analysis of the temperature distribution through the trailing portion of a blade near the coolant passages of liquid cooled gas turbines was made. The analysis was applied to obtain the hot spot temperatures at the trailing edge and influence of design variables. The effective gas temperature was varied from 2000 degrees to 5000 degrees F in each investigation.
Brown, W. Byron↗
Ceramic Heat Pipe for Thermal Management of a High Frequency Inductor
As the power density of electric machines and power electronics continues to increase to meet the demands of more electric aircraft, the thermal management of these devices becomes increasingly important. Ideally, the thermal management solution of the device should have high thermal conductivity and be electrically insulating so that it can be directly integrated with the device in question. Technical ceramics are a class of materials that meet these two requirements. Direct liquid cooling by submerging electric components in a dielectric fluid is an alternate option, but adds system complexity and may incur pumping loss. In this work, the thermal management solution for a high frequency inductor is presented. A conventional wicked heat pipe is designed that is made from a solid ceramic case with a sintered ceramic wick. This heat pipe can provide structural support for the core and windings and is electrically insulating, so it does not incur any additional eddy current losses from the high frequency magnetic fields. It does not require additional pumping power, because conventional wicked heat pipes are passive devices. In this paper, the manufacturing process of the ceramic heat pipe is also presented. It is shown that the sintering of large diameter spherical ceramic particles is difficult due to their high specific surface area and low surface free energy. To overcome this difficulty, a flux material was used to initiate liquid phase sintering. The results of the sintering trials show that for the 120 μm diameter α-Al2O3powder selected for the wick, the combination of 1650°C sintering temperature and the addition of 5 wt% talc sintered the porous matrix together sufficiently for use as a heat pipe wic
High-frequency Inductor↗
Ceramic Heat Pipe for Thermal Management of a High Frequency Inductor
As the power density of electric machines and power electronics continues to increase to meet the demands of more electric aircraft, the thermal management of these devices becomes increasingly important. Ideally, the thermal management solution of the device should have high thermal conductivity and be electrically insulating so that it can be directly integrated with the device in question. Technical ceramics are a class of materials that meet these two requirements. Direct liquid cooling by submerging electric components in a dielectric fluid is an alternate option, but adds system complexity and may incur pumping loss. In this work, the thermal management solution for a high frequency inductor is presented. A conventional wicked heat pipe is designed that is made from a solid ceramic case with a sintered ceramic wick. This heat pipe can provide structural support for the core and windings and is electrically insulating, so it does not incur any additional eddy current losses from the high frequency magnetic fields. It does not require additional pumping power, because conventional wicked heat pipes are passive devices. In this paper, the manufacturing process of the ceramic heat pipe is also presented. It is shown that the sintering of large diameter spherical ceramic particles is difficult due to their high specific surface area and low surface free energy. To overcome this difficulty, a flux material was used to initiate liquid phase sintering. The results of the sintering trials show that for the 120 μm diameter α-Al2O3 powder selected for the wick, the combination of 1650°C sintering temperature and the addition of 5 wt% talc sintered the porous matrix together sufficiently for use as a heat pipe wick.
High frequency inductor↗
Operating SIRTF for maximum lifetime
The instruments of the Space Infrared Telescope Facility (SIRTF) are cooled directly by liquid helium, while the optical system is cooled by helium vapor. The greater the power dissipation into the liquid helium, the more vapor is produced, and the colder the telescope. Observations at shorter wavelengths do not require telescope temperatures as low as those required at longer wavelengths. By taking advantage of this, it may be possible to extend the helium and mission lifetime by 10% or even 20%.
cryogenics↗
Determination of the capture coefficient of a highly directed flow of gaseous carbon dioxide and water vapor on a liquid nitrogen cooled surface, volume II Final report
Capture coefficient of highly directed flow of gaseous carbon dioxide and water vapor on cryogenic quartz crystal microbalance
CRYOPUMPING↗
Al6061-RAM2 Development and Hot-Fire Testing using Additive Manufacturing Laser Powder Directed Energy Deposition for Liquid Rocket Engine Channel-Cooled Nozzles
Aluminum 6061-RAM2 is a high-strength aluminum feedstock developed for additive manufacturing (AM)processes. This alloy leverages Reactive Additive Manufacturing (RAM) technology. The RAM aluminum alloys were developed to be weldable—therefore printable—while equaling or exceeding strength properties of high strength wrought aluminum alloys. NASA and industry partners developed Laser Powder Directed Energy Deposition (LP-DED)additive manufacturing of Al6061-RAM2 for use in aerospace applications. Efforts included establishing build parameters, characterizing the alloy, fabricating components, and completing hot-fire testing of complex internal channel-cooled nozzles. These efforts are to address the growing need for large-scale parts using high-performance light-weight materials. Two rocket engine nozzles were fabricated using LP-DED Al6061-RAM2 that included integral cooling channels. The Al6061-RAM2 has completed process development and initial properties were established. This paper provides an overview of the LP-DED process development, material characterization and properties, component manufacturing, supplemental development, and hot-fire testing. Results from hot-fire testing are provided for a lander-class 31kN (7,000lbf)thrust engine using Liquid Oxygen (LOX)/Liquid Hydrogen(LH2) and LOX/Methane(LCH4).
Al6061-RAM2↗
Al6061-RAM2 Development and Hot-Fire Testing using Additive Manufacturing Laser Powder Directed Energy Deposition for Liquid Rocket Engine Channel-Cooled Nozzles
Aluminum 6061-RAM2 is a high-strength aluminum feedstock developed for additive manufacturing (AM)processes. This alloy leverages Reactive Additive Manufacturing (RAM) technology. The RAM aluminum alloys were developed to be weldable—therefore printable—while equaling or exceeding strength properties of high strength wrought aluminum alloys. NASA and industry partners developed Laser Powder Directed Energy Deposition (LP-DED)additive manufacturing of Al6061-RAM2 for use in aerospace applications. Efforts included establishing build parameters, characterizing the alloy, fabricating components, and completing hot-fire testing of complex internal channel-cooled nozzles. These efforts are to address the growing need for large-scale parts using high-performance light-weight materials. Two rocket engine nozzles were fabricated using LP-DED Al6061-RAM2 that included integral cooling channels. The Al6061-RAM2 has completed process development and initial properties were established. This paper provides an overview of the LP-DED process development, material characterization and properties, component manufacturing, supplemental development, and hot-fire testing. Results from hot-fire testing are provided for a lander-class 31kN (7,000lbf)thrust engine using Liquid Oxygen (LOX)/Liquid Hydrogen(LH2) and LOX/Methane(LCH4).
Al6061-RAM2↗
Al6061-RAM2 Development and Hot-Fire Testing using Additive Manufacturing Laser Powder Directed Energy Deposition for Liquid Rocket Engine Channel-Cooled Nozzles
Aluminum 6061-RAM2 is a high-strength aluminum feedstock developed for additive manufacturing (AM)processes. This alloy leverages Reactive Additive Manufacturing (RAM) technology. The RAM aluminum alloys were developed to be weldable—therefore printable—while equaling or exceeding strength properties of high strength wrought aluminum alloys. NASA and industry partners developed Laser Powder Directed Energy Deposition (LP-DED)additive manufacturing of Al6061-RAM2 for use in aerospace applications. Efforts included establishing build parameters, characterizing the alloy, fabricating components, and completing hot-fire testing of complex internal channel-cooled nozzles. These efforts are to address the growing need for large-scale parts using high-performance light-weight materials. Two rocket engine nozzles were fabricated using LP-DED Al6061-RAM2 that included integral cooling channels. The Al6061-RAM2 has completed process development and initial properties were established. This paper provides an overview of the LP-DED process development, material characterization and properties, component manufacturing, supplemental development, and hot-fire testing. Results from hot-fire testing are provided for a lander-class 31kN (7,000lbf) thrust engine using Liquid Oxygen (LOX)/Liquid Hydrogen (LH2) and LOX/Methane (LCH4).
Al6061-RAM2↗
Determination of capture coefficient of a highly directed flow of gaseous carbon dioxide and water vapor on a liquid nitrogen cooled surface Final report
Continuum source molecular beam to provide highly directed gas flows for determining capture coefficient of gaseous carbon dioxide and water vapor
WATER VAPOR↗
Coupled Reactor Multiphysics and Mass Scalability Assessment for Crewed Megawatt-Class NEP System Architectures
Nuclear Electric Propulsion (NEP) is an in-space propulsion technology capable of enabling opposition and conjunction class crewed Mars missions. NEP subsystems include the reactor for heat generation, a power conversion system (PCS), power management and distribution (PMAD), electric propulsion subsystem (EPS), and a primary heat rejection system. Specific mass, or αe (kg / kWe), is a key performance parameter (KPP) of the propulsion system which is directly scalable with the performance and mass estimates for individual components. To inform technology maturation planning, full system and component level parametric modeling is ongoing to explore the design trade space and illustrate the effect of subsystem design choices on the system KPPs. In this study, scaling of high-assay, low-enriched uranium (HALEU) reactor designs is assessed through coupled reactor physics and thermal hydraulics analyses. Scaling analyses evaluate the impact of system performance parameters (power level, interface temperatures) on mass for direct gas cooled, pumped liquid metal, and passively cooled heat pipe reactor concepts. Each concept requires specific geometries and working fluids to reach the performance goals of PCS interface conditions (temperature, pressure, flow rate) and system mass. The reactor assembly includes the active core (fuel, moderator, cladding, working fluid), axial and radial neutron reflectors, control drums, structural support / pressure vessel, and external radiation shielding. Each of these components are parametrically sized based on performance parameters for a megawatt-class power cycle. Results of this scaling analysis increase NEP propulsion system modeling fidelity and ultimately aim to support technology down-selection along with related technology development planning. The reactor and shield αe are a function of several PCS design choices, and reactor scaling with these parameters must be considered to enable an informed decision on reactor geometry and working fluid combination.
Nuclear Electric Propulsion↗
Coupled Reactor Multiphysics and Mass Scalability Assessment for Crewed Megawatt-Class NEP System Architectures
Nuclear Electric Propulsion (NEP) is an in-space propulsion technology capable of enabling opposition and conjunction class crewed Mars missions. NEP subsystems include the reactor for heat generation, a power conversion system (PCS), power management and distribution, electric propulsion system, and heat rejection system. Specific mass, or α (kg/kWe), is a key performance parameter (KPP) of the propulsion system which is directly scalable with the performance and mass predictions for each individual component. To inform technology maturation planning activities, full system and component level parametric modeling is ongoing to explore the design trade space and illustrate the effect of subsystem design choices on the system KPPs. In this study, scaling of high-assay, low-enriched uranium reactor designs is assessed through coupled reactor physics and thermal hydraulics analyses. Scaling analyses evaluate the impact of system performance parameters (power level, interface temperatures) on mass for direct gas cooled, pumped liquid metal, and passively-cooled heat pipe reactor concepts. Each concept requires specific geometries, fluids, and power conversion interface conditions (temperature, pressure, flow rate) to meet desired performance and mass. The reactor assembly includes the active core (fuel, moderator, cladding, working fluid), axial and radial neutron reflectors, control drums, structural support / pressure vessel, and external radiation shielding. Each of these components are parametrically sized based on performance parameters for a megawatt-class power cycle. Results of this scaling analysis increase NEP propulsion system modeling fidelity and ultimately aim to support concept down-selection along with related technology development planning. The reactor and shield α are a function of several PCS and heat rejection system design choices, and reactor scaling with these parameters must be considered to enable an informed decision on an optimal reactor geometry and working fluid combination.
Nuclear Electric Propulsion↗
Radiative cooling performance of a converging liquid drop radiator
The liquid drop radiator consists of many directed streams of hot liquid drops that are cooled by passing through space and are then collected for reuse. To facilitate the collection of the cooled liquid, a converging geometry might be useful. As the streams converge toward the collector, the density and optical thickness of the droplet cloud are increased. The increase of optical thickness in the flow direction is shown to reduce the local emittance along the length of the radiator.
Siegel, Robert↗
Review of design and operational characteristics of the 0.3-meter transonic cryogenic tunnel
The past 6 years of operation with the NASA Langley 0.3 m transonic cryogenic tunnel (TCT) show that there are no insurmountable problems associated with cryogenic testing with gaseous nitrogen at transonic Mach numbers. The fundamentals of the concept were validated both analytically and experimentally and the 0.3 m TCT, with its unique Reynolds number capability, was used for a wide variety of aerodynamic tests. Techniques regarding real-gas effects were developed and cryogenic tunnel conditions can be set and maintained accurately. Cryogenic cooling by injecting liquid nitrogen directly into the tunnel circuit imposes no problems with temperature distribution or dynamic response characteristics. Experience with the 0.3 m TCT, indicates that there is a significant learning process associated with cryogenic, high Reynolds number testing. Many of the questions have already been answered; however, factors such as tunnel control, run logic, economics, instrumentation, and model technology present many new and challenging problems.
Ray, E. J.↗
Phase 1 Space Fission Propulsion System Design Considerations
Fission technology can enable rapid, affordable access to any point in the solar system. If fission propulsion systems are to be developed to their full potential; however, near-term customers must be identified and initial fission systems successfully developed, launched, and operated. Studies conducted in fiscal year 2001 (IISTP, 2001) show that fission electric propulsion (FEP) systems operating at 80 kWe or above could enhance or enable numerous robotic outer solar system missions of interest. At these power levels it is possible to develop safe, affordable systems that meet mission performance requirements. In selecting the system design to pursue, seven evaluation criteria were identified: safety, reliability, testability, specific mass, cost, schedule, and programmatic risk. A top-level comparison of three potential concepts was performed: an SP-100 based pumped liquid lithium system, a direct gas cooled system, and a heatpipe cooled system. For power levels up to at least 500 kWt (enabling electric power levels of 125-175 kWe, given 25-35% power conversion efficiency) the heatpipe system has advantages related to several criteria and is competitive with respect to all. Hardware-based research and development has further increased confidence in the heatpipe approach. Successful development and utilization of a "Phase 1" fission electric propulsion system will enable advanced Phase 2 and Phase 3 systems capable of providing rapid, affordable access to any point in the solar system.
Houts, Mike↗
Channel Wall Nozzle Manufacturing and Hot-Fire Testing Using a Laser Wire Direct Closeout Technique for Liquid Rocket Engines
A regeneratively-cooled nozzle for liquid rocket engine applications is a significant cost of the overall engine due to the complexities of manufacturing a large thin-walled structure that must operate in extreme temperature and pressure environments. The National Aeronautics and Space Administration (NASA) has been investigating and advancing methods for fabrication of liquid rocket engine channel wall nozzles to realize further cost and schedule improvements over traditional techniques. The methods being evaluated are targeting increased scale required for current NASA and commercial space programs. Several advanced rapid fabrication methods are being investigated for forming of the inner liner, producing the coolant channels, closeout of the coolant channels, and fabrication of the manifolds. NASA's Marshall Space Flight Center (MSFC) has completed process development and subscale hot-fire testing of a series of these advanced fabrication channel wall nozzle technologies to gather performance data in a relevant environment. The primary fabrication technique being discussed in this paper is Laser Wire Direct Closeout (LWDC). This process has been developed to significantly reduce the time required for closeouts of regeneratively-cooled slotted liners. It allows for channel closeout to be formed in place in addition to the structural jacket without the need for channel fillers or complex tooling. Additional technologies were also tested as part of this program including water jet milling and arc-based additive manufacturing deposition. Each nozzle included different fabrication features, materials, and methods to demonstrate durability in a hot-fire environment. The results of design, fabrication, and hot-fire testing are discussed in this paper.
Gradl, Paul R.↗
Actively Cooled SLMS(TM) Technology for HEL Applications
Mr. Jacoby is the Chief Scientist for Schafer's Lightweight Optical Systems business area with twenty four years experience in laser and optical systems for space and military applications. He and colleague Dr. Goodman conceived and developed Silicon Lightweight Mirrors (SLMS(TM)) technologies for space applications from the extreme UV to FAR IR wavelengths. Schafer has demonstrated two different methods for actively cooling our Silicon Lightweight Mirrors (SLMS(TM)) technology. Direct internal cooling was accomplished by flowing liquid nitrogen through the continuous open cell core of the SLMS(TM) mirror. Indirect external cooling was accomplished by flowing liquid nitrogen through a CTE matched Cesic square-tube manifold that was bonded to the back of the mirror in the center. Testing was done in the small 4-foot thermal/vacuum chamber located at the NASA/MSFC X-Ray Calibration Facility. Seven thermal diodes were located over the front side of the 5 inch diameter mirror and one was placed on the outlet side of the Cesic manifold. Results indicate that the mirror reaches steady state at 82K in less than four minutes for both cooling methods. The maximum temperature difference of the eight diodes was less than 200 mK when the mirror was internally cooled and covered with MLI to insulate it from the large 300 K aluminum plate that was used to mount it.
Jacoby, Marc T.↗
The cryogenic wind tunnel for high Reynolds number testing
Experiments performed at the NASA Langley Research Center in a cryogenic low-speed continuous-flow tunnel and in a cryogenic transonic continuous-flow pressure tunnel have demonstrated the predicted changes in Reynolds number, drive power, and fan speed with temperature, while operating with nitrogen as the test gas. The experiments have also demonstrated that cooling to cryogenic temperatures by spraying liquid nitrogen directly into the tunnel circuit is practical and that tunnel temperature can be controlled within very close limits. Whereas most types of wind tunnel could operate with advantage at cryogenic temperatures, the continuous-flow fan-driven tunnel is particularly well suited to take full advantage of operating at these temperatures. A continuous-flow fan-driven cryogenic tunnel to satisfy current requirements for test Reynolds number can be constructed and operated using existing techniques. Both capital and operating costs appear acceptable.
Kilgore, R. A.↗