Results for “dislocation density evolution”

NASA NTRS1988

Microstructural evolution on crystallizing the glassy phase in a 6 weight percent Y2O3-Si3N4 ceramic

X-ray diffraction and analytical electron microscopy have been used to study the crystallization of the grain-boundary glass in a 6 wt pct Y2O3-Si3N4 ceramic. Upon crystallization, high densities of dislocations formed in the Si3N4 grains and remained after 5 h at temperature. However, prolonged holds at the crystallization temperature effectively annealed out the dislocations. Other features present in the microstructure are characterized.

Lee, W. E.↗

NASA NTRS1999

Step Bunching: Influence of Impurities and Solution Flow

Step bunching results in striations even at relatively early stages of its development and in inclusions of mother liquor at the later stages. Therefore, eliminating step bunching is crucial for high crystal perfection. At least 5 major effects causing and influencing step bunching are known: (1) Basic morphological instability of stepped interfaces. It is caused by concentration gradient in the solution normal to the face and by the redistribution of solute tangentially to the interface which redistribution enhances occasional perturbations in step density due to various types of noise; (2) Aggravation of the above basic instability by solution flowing tangentially to the face in the same directions as the steps or stabilization of equidistant step train if these flows are antiparallel; (3) Enhanced bunching at supersaturation where step velocity v increases with relative supersaturation s much faster than linear. This v(s) dependence is believed to be associated with impurities. The impurities of which adsorption time is comparable with the time needed to deposit one lattice layer may also be responsible for bunching; (4) Very intensive solution flow stabilizes growing interface even at parallel solution and step flows; (5) Macrosteps were observed to nucleate at crystal corners and edges. Numerical simulation, assuming step-step interactions via surface diffusion also show that step bunching may be induced by random step nucleation at the facet edge and by discontinuity in the step density (a ridge) somewhere in the middle of a face. The corresponding bunching patterns produce the ones observed in experiment. The nature of step bunching generated at the corners and edges and by dislocation step sources, as well as the also relative importance and interrelations between mechanisms 1-5 is not clear, both from experimental and theoretical standpoints. Furthermore, several laws controlling the evolution of existing step bunches have been suggested, though unambiguous conclusions are still missing. Addressing these issues is the major goal of the present project. The theory addressing the above problem, experimental methods, several figures which include: (1) the spatial wave numbers at which the system is neutrally stable as a function of growth velocity for linear kinetics and supersaturation for nonlinear kinetics; (2) a schematic of the experiment of lysozyme crystal growing under conditions of natural convection; (3) fluctuations in time, t, of the normal growth rate, R(t), vicinal slope, p(t) and Fourier Spectra of R(t), discussions and conclusions are presented.

Chernov, A. A.↗

NASA NTRSDate not supplied

Fast Assessment of Metal Performance through Dislocation Physics and Machine Learning

The microstructure of metals is key to their mechanical properties. The types, density, composition and morphology of crystal defects all have pronounced impact on the properties. Changes to the microstructure occurring during processing and use can be very striking. The emerging technology additive manufacturing (AM) has the potential to improve performance by allowing optimized designs, but the process and environments can lead to unusual microscale features whose properties must be understood and characterized to enable higher technological readiness levels and application. Experimentally, an extensive evaluation of mechanical properties of 3D printed metals is a challenge, and anomalous effects related to the AM process add complexity. We present a new machine learning (ML) model predicting mechanical response based on dislocation mediated plasticity simulations. A large set of 3D discrete dislocation dynamics simulations with wide ranges of loading conditions is transformed to preprocessed data ready for training with the ML model. The trained model can predict the mechanical response of Mo30W for a given microstructure evolution, providing key information essential for optimization of AM processing.

Jaehyun Cho↗

NASA NTRSDate not supplied

Fast Assessment of Metal Performance through Dislocation Physics and Machine Learning

The microstructure of metals is key to their mechanical properties. The types, density, composition and morphology of crystal defects all have pronounced impact on the properties. Changes to the microstructure occurring during processing and use can be very striking. The emerging technology additive manufacturing (AM) has the potential to improve performance by allowing optimized designs, but the process and environments can lead to unusual microscale features whose properties must be understood and characterized to enable higher technological readiness levels and application. Experimentally, an extensive evaluation of mechanical properties of 3D printed metals is a challenge, and anomalous effects related to the AM process add complexity. We present a new machine learning (ML) model predicting mechanical response based on dislocation mediated plasticity simulations. A large set of 3D discrete dislocation dynamics simulations with wide ranges of loading conditions is transformed to preprocessed data ready for training with the ML model. The trained model can predict the mechanical response of Mo30W for a given microstructure evolution, providing key information essential for optimization of AM processing.

Jaehyun Cho↗

NASA NTRS2006

Recent Results from Epitaxial Growth on Step Free 4H-SiC Mesas

This paper updates recent progress made in growth, characterization, and understanding of high quality homoepitaxial and heteroepitaxial films grown on step-free 4H-SiC mesas. First, we report initial achievement of step-free 4H-SiC surfaces with carbon-face surface polarity. Next, we will describe further observations of how step-free 4H-SiC thin lateral cantilever evolution is significantly impacted by crystal faceting behavior that imposes non-uniform film thickness on cantilever undersides. Finally, recent investigations of in-plane lattice constant mismatch strain relief mechanisms observed for heteroepitaxial growth of 3C-SiC as well as 2H-AlN/GaN heterofilms on step-free 4H-SiC mesas will be reviewed. In both cases, the complete elimination of atomic heterointerface steps on the mesa structure enables uniquely well-ordered misfit dislocation arrays to form near the heterointerfaces with remarkable lack of dislocations threading vertically into the heteroepilayers. In the case of 3C-SiC heterofilms, it has been proposed that dislocation half-loops nucleate at mesa edges and glide laterally along the step-free 3C/4H interfaces. In contrast, 3C-SiC and 2H-AlN/GaN heterofilms grown on 4H-SiC mesas with steps exhibit highly disordered interface misfit dislocation structure coupled with 100X greater density of dislocations threading through the thickness of the heteroepilayers. These results indicate that the presence of steps at the heteroepitaxial interface (i.e., on the initial heteroepitaxial nucleation surface) plays a highly important role in the defect structure, quality, and relaxation mechanisms of single-crystal heteroepitaxial films.

Neudeck, Philip G.↗