SEARCH · Search NASA

Results for “dither”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

18 records

All sources NASA NTRS DOE OSTI

DOE OSTI2020

O 2 dosage as a descriptor of TWC performance under lean/rich dithering in stoichiometric natural gas engines

The effects of oscillations in gas composition, known as lean/rich dithering, on the performance of a commercial Pd-based three-way catalyst (TWC) for stoichiometric natural gas (NG) engines were evaluated using synthetic exhaust flow reactor experiments. Under simulated NG exhaust conditions, NO conversion was intimately correlated to CH 4 conversion at slightly fuel-rich operating conditions. CH 4 conversion significantly varied with lambda (or O 2 concentration) and depended on the direction of the lambda change. The dynamic CH 4 conversion is likely related to the change of catalyst oxidation state and structures of Pd active sites. The CH 4 -NO cross-over point was found at a rich-biased lambda rather than stoichiometry. Compared to static operation, catalyst performance was much higher under a realistic dithering condition. The impacts of dithering parameters including amplitude and frequency on CH 4 and NO conversions were explored. O 2 dosage is proposed as an effective descriptor of the TWC dithering performance. In the O 2 -dosage space, the performance of distinct dithering parameters collapse, helping to elucidate the fundamental influence of dithering parameters on TWC performance. With the help of O2 dosage, an optimal operating window leading to high CH 4 and NO conversions was identified. A higher dithering amplitude is required to keep the catalyst in a reduced state for higher CH 4 and NO conversions, while an appropriate O 2 dosage that does not exceed the breakthrough OSC is necessary to avoid excess O 2 that results in NO slip. The dithering amplitude and O 2 -dosage-metric maps provide a new method for studying dynamic TWC performance and identifying optimum operation strategies.

03 NATURAL GAS↗

DOE OSTI2023

Discrete offset dithered waveform averaging for high-fidelity digitization of repetitive signals

Methods and devices for digitizing an analog repetitive signal using waveform averaging are described. An example method includes generating a discrete set of analog dither offset voltages, wherein at least two of the discrete set of analog dither offset voltages are different from each other, receiving the analog repetitive signal comprising multiple instances of a waveform, wherein the waveform has a waveform duration, generate a timing alignment to align each waveform of the analog repetitive signal and the corresponding analog dither offset voltage over the waveform duration, combining, based on the timing alignment, each waveform and the corresponding analog dither offset voltage over the waveform duration to produce an analog output signal, converting the analog output signal to a digital output signal, and producing, based on the timing alignment, a digital averaged signal based on averaging the multiple instances of the waveform in the analog output signal.

Buckley, Brandon Walter↗

DOE OSTI2023

Continuous dithered waveform averaging for high-fidelity digitization of repetitive signals

Methods and devices for digitizing an analog repetitive signal using waveform averaging are described. An example method includes generating a time-varying dither signal, receiving the analog repetitive signal comprising multiple instances of a waveform, wherein each waveform has a waveform duration, wherein an average of the time-varying dither signal over multiple waveform durations is substantially zero, and wherein the time-varying dither signal varies over each waveform duration, generating a timing alignment, combining each waveform with the corresponding portion of the time-varying dither signal over each waveform duration to produce an analog output signal, converting the analog output signal to a digital output signal, and producing, based on the timing alignment, a digital averaged signal based on averaging the multiple instances of the waveform in the analog output signal, wherein the timing alignment is used to align the multiple instances of the waveform in the analog output signal.

Buckley, Brandon Walter↗

DOE OSTI2021

ELECTRON COOLING USING A PULSED AND DITHERING BEAM FROM AN ELECTROSTATIC ELECTRON COOLER

Electron cooling continues to be an invaluable technique to reduce and maintain the emittance in hadron storage rings such as the EIC and EICC where stochastic cooling is inefficient and radiative cooling is negligible. Extending the energy range of electron coolers beyond what is feasible with the conventional, electrostatic approach necessitates the use of RF fields for acceleration and, thus, a bunched electron beam. To experimentally investigate how the relative time structure of the two beams affects the cooling properties, we have set up a pulsed-beam cooling device by adding a synchronized pulsing circuit to the conventional electron source of the CSRm cooler at Institute of Modern Physics. Using both constant and modulated synchronization between electron pulses and ion bunches, we have measured the effects of the electron bunch length and longitudinal ion focusing strength on the temporal evolution of the longitudinal and transverse ion beam profile and demonstrated the detrimental effect of timing jitter as predicted by space-charge theory and simulations. Our experiment suggests a need for further investigations of specific aspects of bunched cooling such as synchro-betatron coupling and phase dithering effects when using short electron bunches to cool longer ion bunches. However, given the comparatively long IBS lifetime of higher-energy proton storage rings like the EIC, slow dithering could potentially provide an option to save cost on the electron cooler linac.

Wang, Haipeng↗

DOE OSTI2024

Measuring Fiber Positioning Accuracy and Throughput with Fiber Dithering for the Dark Energy Spectroscopic Instrument

Highly multiplexed, fiber-fed spectroscopy is enabling surveys of millions of stars and galaxies. The performance of these surveys depends on accurately positioning fibers in the focal plane to capture target light. We describe a technique to measure the positioning accuracy of fibers by dithering fibers slightly around their ideal locations. This approach also enables measurement of the total system throughput and point-spread function delivered to the focal plane. We then apply this technique to observations from the Dark Energy Survey Instrument (DESI), and demonstrate that DESI positions fibers to within 0farcs08 of their targets (5% of a fiber diameter) and achieves a system throughput within about 7% of expectations.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2024

Extremum seeking control of distributed energy resources with decaying dither and equilibrium-based switching

Embodiments relate to an operating system coupled to and controlling at least one Distributed Energy Resource (DER) in a smart grid and includes an electricity distribution network and a 2-dimensional Extremum Seeking (2D-ES) controller coupled to network. The electricity distribution network has first and second inputs and one output and maps all active power and reactive power inputs to the smart grid providing measurements of an objective function. The 2D-ES controller controls the DER and includes an active power loop and a reactive power loop. The active power loop is in communication with the first input and the output, governs active power contribution, and receives measurements of the objective function which contain static and oscillatory components. The reactive power loop is in communication with the second input and the output, governs reactive power contribution, and receives measurements of the objective function which contain static and oscillatory components.

Arnold, Daniel↗

DOE OSTI2021

The role of edge plasma parameters in H-mode density limit on the JET-ILW

A study of a dataset of JET H-mode plasma with the Be/W ITER-like wall (JET-ILW) shows that reaching the edge MHD ballooning limit leads to confinement degradation. However, unlike JET plasmas with a carbon wall (JET-C), the JET-ILW plasmas stay in a marginal dithering phase for a relatively long period, associated with a higher (≈20%) H-mode density limit (HDL) than JET-C equivalents. This suggests that ITER could be operated in H-mode with higher density than the scaling based on carbon wall devices, but likely with a dithering phase plasma with lower confinement. A new, reliable estimator for JET E r, min has been derived by combining HRTS measurements of pedestal gradient and edge-SOL decay lengths. JET radial E r ETB wells are observed in the range of -15 to -60 kV m -1 in high performance H-modes, consistent with previous CXRS results in ASDEX Upgrade. The results imply that a higher positive E × B shear in the near SOL plays a role in sustaining a marginal phase in JET-ILW which leads to a higher HDL than that in JET-C. The results of the JET-ILW dataset show agreement with the Goldston finite collisionality HD model for SOL broadening at high collisionality. A hypothesis for the dithering H-mode phase is proposed: as n e,SOL increases, ν *,SOL increases, SOL broadens, E r shear decreases, triggers L-mode; n e drops, ν *,SOL decreases, SOL becomes narrower, and E r shear increases, triggering H-mode, resulting in a cycle of H–L–H- oscillations. For burning plasma devices, such as ITER, operating just below the MHD limit for the dithering phase could be a promising regime for maximising core density, and fusion performance while minimising plasma-material interaction. The oscillatory signal during the dithering phase could be used as a precursor of undesirable plasma performance for control purposes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Optimizing LSST observing strategy for weak lensing systematics

ABSTRACT The Legacy Survey of Space and Time (LSST) survey will provide unprecedented statistical power for measurements of dark energy. Consequently, controlling systematic uncertainties is becoming more important than ever. The LSST observing strategy will affect the statistical uncertainty and systematics control for many science cases; here, we focus on weak lensing (WL) systematics. The fact that the LSST observing strategy involves hundreds of visits to the same sky area provides new opportunities for systematics mitigation. We explore these opportunities by testing how different dithering strategies (pointing offsets and rotational angle of the camera in different exposures) affect additive WL shear systematics on a baseline operational simulation, using the ρ-statistics formalism. Some dithering strategies improve systematics control at the end of the survey by a factor of up to ∼3–4 better than others. We find that a random translational dithering strategy, applied with random rotational dithering at every filter change, is the most effective of those strategies tested in this work at averaging down systematics. Adopting this dithering algorithm, we explore the effect of varying the area of the survey footprint, exposure time, number of exposures in a visit, and exposure to the Galactic plane. We find that any change that increases the average number of exposures (in filters relevant to WL) reduces the additive shear systematics. Some ways to achieve this increase may not be favorable for the WL statistical constraining power or for other probes, and we explore the relative trade-offs between these options given constraints on the overall survey parameters.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2021

Suppression of ITG turbulence due to spectral shift during biasing induced H-mode on HBT-EP

Investigations of biasing induced H-mode discharges on HBT-EP show that the edge turbulence is consistent with the ion temperature gradient) mode and have allowed for the controlled observation of the effect of applied flow shear on the turbulence. Measurements of the radial wavenumber spectrum of floating potentials at the edge show that the turbulence intensity decreases with increasing shift in the spectrum average ⟨ k r ⟩ when increasing amounts of bias probe voltage (and increasing amounts of flow shear) is applied. This is in agreement with the spectral shift model [Staebler et al., Phys. Rev. Lett. 110, 055003 2013] for turbulence suppression via sheared flow. A shift in the wavenumber spectrum occurs at applied electrode voltages and currents below the threshold needed for an L–H transition, and a dithering transition is obtained when biasing near the threshold. Suppression of blob-filament turbulence in the scrape-off layer (SOL) precedes the L–H transition, with the SOL turbulence remaining low throughout the dithering phase, despite the modulation of turbulence levels in the nearby edge. This demonstrates that the SOL turbulence “decouples” from the edge turbulence. The spectral shift in the measured radial wavenumber is corroborated by the direct measurement of eddy tilt angle using a novel time delay analysis technique first developed for Doppler reflectometry [Pinzon et al., Plasma Phys. Controlled Fusion 61, 105009 (2019)] but adapted here for floating potential measurements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Bifurcation from L-mode to internal transport barrier triggered by a magnetic island in tokamak plasmas

Magnetic islands are believed to be responsible for triggering the internal transport barrier (ITB) around the rational surface and hence improves confinement in magnetic confinement fusion plasma, for more than two decades. Although some recent theoretical or modelling works support this hypothesis, the direct experimental demonstration on the ITB triggered by a magnetic island is still missing. Here, we report the first experimental observation that the increase in the magnetic island width triggers the bifurcation of the plasma transport state from a low confinement mode (L-mode) to an ITB mode in tokamak plasma. At medium island widths, the bifurcation appears with a dithering phase, i.e. plasma transitions from L-mode to ITB or vice versa quasi-periodically. As the island width further increases, the dithering ITB transitions into a steady ITB. The electron temperature gradient inside the ITB increases with island width. The trigger of the ITB and further enhancement of the ITB performance are also demonstrated by locking the island via applying a resonant magnetic perturbation field. The reduction of density fluctuations in the ITB region is observed and indicates turbulence suppression during ITB formation. These findings offer new insights for understanding ITB formation and robust ITB control.

internal transport barrier↗

DOE OSTI2021

High signal-to-noise ratio differential conductance spectroscopy

The scanning tunneling microscope (STM) has enabled manipulation and interrogation of surfaces with atomic-scale resolution. Electronic information about a surface is obtained by combining the imaging capability of the STM with scanning tunneling spectroscopy, i.e., measurement of current-voltage (I/V) characteristics of the surface. We propose a change in the STM feedback loop that enables capturing a higher quality dI/dV image. A high frequency dither voltage is added to the bias voltage of the sample, and the fundamental frequency component of the resulting current is demodulated. The in-phase component of this signal is then plotted along with the X and Y position data, constructing the dI/dV image. Here, we show that by incorporating notch filters in the STM feedback loop, we may utilize a high-amplitude dither voltage to significantly improve the quality of the obtained dI/dV image.

42 ENGINEERING↗

DOE OSTI2023

Understanding the negative triangularity ELM trigger and ELM free state on DIII-D with ECE-imaging

Here, the Electron Cyclotron Emission Imaging (ECEI) diagnostic was used to observe a finite-n interchange mode structure in the edge of negative triangularity shaped plasmas on DIII-D. At a small negative triangularity (δ u = -0.2), the plasma is in the H-mode with ELMs that are triggered by a low-n interchange mode. At a larger negative triangularity (δ u = -0.4) and low NBI power (2 MW), a dithering oscillation is observed that is triggered by a low-n interchange mode, whereas at higher NBI power (>2 MW), the edge reverts to L-mode and the low-n interchange mode is present continuously. In all cases, the edge pressure gradient is clamped when the interchange mode is present. It is concluded that the low-n interchange mode prevents the plasma from transitioning to H-mode at a large negative triangularity. This agrees with linear BOUT++ simulations which suggest that the interchange-type MHD can be a resistive ballooning mode whereby resistivity can significantly increase the finite-n ballooning mode growth rate. The absence of H-mode at large negative triangularity can, thus, be explained by the excitation of low-n pressure driven resistive ballooning modes in the plasma edge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

The La Silla Schmidt Southern Survey

We present the La Silla Schmidt Southern Survey (LS4), a new wide-field, time-domain survey to be conducted with the 1 m ESO Schmidt telescope. The 268 megapixel LS4 camera mosaics 32 2k × 4k fully depleted CCDs, providing a ∼20 deg 2 field of view with 1″ pixel −1 resolution. The LS4 camera will have excellent performance at longer wavelengths: in a standard 45 s exposure the expected 5σ limiting magnitudes in g, i, z are ∼21.5, ∼20.9, and ∼20.3 mag (AB), respectively. The telescope design requires a novel filter holder that fixes different bandpasses over each quadrant of the detector. Two quadrants will have i band, while the other two will be g and z band with color information obtained by dithering targets across the different quadrants. The majority (90%) of the observing time will be used to conduct a public survey that monitors the extragalactic sky at both moderate (3 days) and high (1 day) cadence, as well as focused observations within the Galactic plane and bulge. Alerts from the public survey will be broadcast to the community via established alert brokers. LS4 will run concurrently with the Vera C. Rubin Observatory’s Legacy Survey of Space and Time (LSST). The combination of LS4+LSST will enable detailed holistic monitoring of many nearby transients: high-cadence LS4 observations will resolve the initial rise and peak of the light curve while less-frequent but deeper observations by LSST will characterize the years before and after explosion. Here, we summarize the primary science objectives of LS4 including microlensing events in the Galaxy, extragalactic transients powered by massive black holes or stellar explosions, the search for electromagnetic counterparts to multi-messenger events, and supernova cosmology.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2022

Analysis of combustion chamber deposit growth on temperature swing thermal barrier coatings in a spark ignition engine

Temperature swing thermal barrier coatings (TBCs) have the potential to improve efficiency and performance through thermal management of the combustion chamber. However, the effects of combustion chamber deposits (CCDs) on the surface of the TBCs are unclear. Therefore, this paper analyzes the impact of CCD formation on a temperature swing TBC. A piston and a heat flux probe coated with a novel material are installed in a single-cylinder research engine at a low-load condition for 62.5 h to promote CCD growth. Every 12.5 h, the performance at a knock limited condition is assessed and thermophysical property measurements on the heat flux probe are performed. Net thermal efficiency increased by 0.4% absolute after 12.5 h relative to the baseline condition, but further CCD growth caused a dithering of efficiency between the 12.5 h and baseline points. The KLSA retarded consistently throughout this period. As a result, external property measurements with the coated heat flux probe showed an improvement in the thermophysical properties of the TBC/CCD layer.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2021

Stabilization of the 81-channel coherent beam combination using machine learning

We develop a rapidly converging algorithm for stabilizing a large channel-count diffractive optical coherent beam combination. An 81-beam combiner is controlled by a novel, machine-learning based, iterative method to correct the optical phases, operating on an experimentally calibrated numerical model. A neural-network is trained to detect phase errors based on interference pattern recognition of uncombined beams adjacent to the combined one. Due to the non-uniqueness of solutions in the full space of possible phases, the network is trained within a limited phase perturbation/error range. This also reduces the number of samples needed for training. Simulations have proven that the network can converge in one step for small phase perturbations. When the trained neural-network is applied to a realistic case of 360 degree full range, an iterative scheme exploits random walking at the beginning, with the accuracy of prediction on phase feedback direction, to allow the neural-network to step into the training range for fast convergence. This neural-network-based iterative method of phase detection works tens of times faster than the commonly used stochastic parallel gradient descent approach (SPGD) using a single-detector and random dither when both are tested with random phase perturbations.

Wang, Dan↗

DOE OSTI2021

Demonstration of Electron Cooling using a Pulsed Beam from an Electrostatic Electron Cooler

Electron cooling continues to be an invaluable technique to reduce and maintain the emittance in hadron storage rings in cases where stochastic cooling is inefficient and radiative cooling is negligible. Extending the energy range of electron coolers beyond what is feasible with the conventional, electrostatic approach necessitates the use of RF fields for acceleration and, thus, a bunched electron beam. To experimentally investigate how the relative time structure of the two beams affects the cooling properties, we have set up a pulsed-beam cooling device by adding a synchronized pulsing circuit to the conventional electron source of the CSRm cooler at Institute of Modern Physics *. We show the effect of the electron bunch length and longitudinal ion focusing strength on the temporal evolution of the longitudinal and transverse ion beam profile and demonstrate the detrimental effect of timing jitter as predicted by theory and simulations. Compared to actual RF-based coolers, the simplicity and flexibility of our setup will facilitate further investigations of specific aspects of bunched cooling such as synchro-betatron coupling and phase dithering.

Bruker, M. W.↗

DOE OSTI2021

Demonstration of Electron Cooling using a Pulsed Beam from an Electrostatic Electron Cooler

Bruker, M. W.↗

DOE OSTI2023

Impact of Oxygen Storage Components in Prototype Pd-Based Three-Way Catalysts under Exhaust Conditions Relevant to Propane Engines

With increasing concerns about global warming, the push for sustainable and eco-friendly fuels is accelerating. Propane, recognized as liquefied petroleum gas or LPG, has garnered research interest as an alternative fuel due to its notable advantages, including a high-octane rating, reduced greenhouse gas emissions, and potential cost-effectiveness. However, to realize its full potential as an alternative fuel it is essential to develop catalysts that efficiently handle emissions at low temperatures. In our research, we investigated three distinct palladium (Pd)-based three-way catalyst (TWC) formulations (PdRh, Pd-only, and Pd-OSC) to investigate the influence of typical TWC components rhodium (Rh) and oxygen storage components (OSC) in exhaust scenarios relevant to propane-fueled engines. Among these, the formulation containing oxygen storage components (Pd-OSC) showed the highest reactivity for both NO and C 3 H 8 while minimizing performance degradation from hydrothermal aging (HTA). Notably, the temperature of 50% conversion (T50) for propane in the Pd-OSC fresh and HTA sample was lower by 30 °C and 13 °C, respectively, compared to the Pd-only sample, highlighting the role of oxygen storage materials in enhancing catalyst performance, even without dithering. Additionally, N 2 physisorption showed that the PdOSC sample has a higher surface area and increased pore volume. This underscores the idea that OSC materials not only augment the catalyst’s porosity but also optimize reactant accessibility to active sites, thus elevating catalytic efficiency. In addition to evaluating performance, we further explored the performance and characteristics of the catalysts using catalytic probe reactions, such as water–gas shift and steam reforming reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗