Search NASA⌕ Search

SEARCH · Search NASA

Results for “divertor ;fusion materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Impact of gas injection location and divertor surface material on ITER fusion power operation phase divertor performance assessed with SOLPS-ITER *

Abstract The ITER divertor design and performance assessment, primarily based on the SOLPS-4.3 burning plasma database (Pitts R. et al 2019 Nucl. Mater. Energy 20 100696), assumes the use of beryllium (Be) as the divertor surface material and the injection of gas from the main chamber top. However, the current ITER baseline favors gas injection from the more toroidally symmetric sub-divertor region. This paper evaluates the implications of these assumptions for divertor performance in the ITER fusion power operation phase. The impact of the divertor surface material and the gas injection location on the main ions mirrors the hydrogen only low power phase scenario shown in Park J.-S. et al (2020 Nucl. Fusion 61 016021). However, during burning plasma operation, extrinsic impurity seeding will be required. In the case of neon (Ne), studied here, impurity retention is influenced by both the divertor surface material and the fueling location. Neon leakage increases due to more energetic reflection from tungsten than beryllium, but equivalent divertor performance can be achieved by adjusting the neon seeding rate. While the impurity seeding location does not affect the distributions of impurity or radiation, the fueling location does. Top fueling provides local ionization sources mainly in the mid-SOL under detached conditions, enhancing divergences of the flux there (source-driven flow), bringing stagnation points close to the fueling location, and equilibrating flows towards both targets. In contrast, the global flow pattern (in the absence of fluid drifts) in the case of sub-divertor fueling is biased towards the inner target. Impurity flows, driven by force balance, largely mirror those of the main ion flow, including the stagnation point. The case with top fueling enhances Ne retention and corresponding radiation in the outer divertor, effectively reducing the total and peak target heat fluxes by 20%–40%, compared to the case with divertor fueling. Meanwhile, the case with outer target fueling also achieves similar reductions by enhancing plasma-neutral interactions. These results suggest the possibility that the selection of the fueling location and throughput can be used as an actuator to control impurity divertor retention and divertor radiation asymmetry.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Final Design of the Material Plasma Exposure eXperiment

The Material Plasma Exposure eXperiment (MPEX) has completed its design phase. MPEX will be a unique facility to investigate plasma material interactions (PMIs) under fusion prototypic divertor conditions in steady state. This includes plasma exposure conditions expected in a fusion reactor divertor. Materials to be investigated will include solids, liquids, and neutron pre-irradiated materials. Electron and ion heating will allow for a large operational domain ranging from erosion-dominated PMI conditions to deposition-dominated PMI conditions. An overview of the final design for all MPEX systems is given. Here, in particular, it is shown how mission-driven project requirements have led to detailed design choices with innovative solutions. Examples are the water-cooled helicon window, the electron cyclotron heating launcher, the target holder and manipulator, and the autonomous decouplers.

Fusion reactor↗
DOE OSTI2023

The comparative strength and fracture toughness properties of commercial 95W-3.5Ni1.5Fe and 95W-3.5Ni1.5Cu tungsten heavy alloys

Due to the sharp surface cracks resulting from high and cyclic thermal loads, fracture toughness is a crucial property for fusion divertor materials. Tungsten heavy alloys (WHA) have emerged as a leading candidate for plasma facing component applications. Both the WNiFe and WNiCu WHAs have been considered. However, there is no fracture toughness data in the literature on the WNiCu WHA. Therefore, maximum load elastic–plastic fracture toughness (K Jm ) of a commercial 95W-3.5Ni1.5Cu (NiCu) WHA plate is reported here for the first time. The NiCu WHA K Jm is compared to a corresponding K Jm for commercial 95W-3.5Ni1.5Fe (NiFe) WHA, along with comparisons of their respective microstructures, microhardness, and tensile properties. Although their room temperature yield strengths are similar (≈ 600 MPa), the NiFe WHA has higher ultimate stress (818 MPa vs. 642 MPa) and total elongation (8% vs. 1.2%) compared to the NiCu WHA. Most notably, the room temperature elastic–plastic K Jm for the NiFe WHA of ≈ 80 ± 8 MPa$\sqrt{m}$, is nearly twice that of the NiCu WHA at ≈ 47 ± 4 MPa$\sqrt{m}$. Further, while the NiFe WHA experienced stable ductile tearing, the crack propagated unstably (approximately elastically) after reaching the maximum load in the NiCu WHA. The higher K Jm of the NiFe WHA is attributed to its higher flow stress and ductility, along with the energy dissipation and microcrack dilatational stress shielding, provided by a wide distribution of arrested process-zone microcracks, which are largely absent in the NiCu WHA. Since, the 95W-NiFe WHA has distinctly better mechanical properties than 95W-NiCu WHA, it is a more suitable candidate for the fusion reactor application.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Informing ARC divertor design and plasma facing material selection through integrated modeling

This INFUSE 2023 project between UCLA and Commonwealth Fusion Systems used computer modeling to test whether tungsten materials can survive in CFS's ARC fusion reactor divertor. The team simulated plasma conditions and material responses, finding that tungsten-rhenium alloys resist grain growth better than pure tungsten, and that hydrogen buildup depends more on particle flux than temperature. The work helps CFS design durable plasma-facing components for their fusion power plant.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Ion heating in the PISCES-RF liquid-cooled high-power, steady-state, helicon plasma device

Radio frequency (RF) driven helicon plasma sources are commonly used for their ability to produce high-density argon plasmas ( n > 10 19 m -3 ) at relatively moderate powers (typical RF power < 2 kW). Typical electron temperatures are <10 eV and typical ion temperatures are <0.6 eV. A newly designed helicon antenna assembly (with concentric, double-layered, fully liquid-cooled RF-transparent windows) operates in steady-state at RF powers up to 10 kW. We report on the dependence of argon plasma density, electron temperature and ion temperature on RF power. At 10 kW, ion temperatures >2 eV in argon plasmas are measured with laser induced fluorescence, which is consistent with a simple volume averaged 0D power balance model. 1D Monte Carlo simulations of the neutral density profile for these plasma conditions show strong neutral depletion near the core and predict neutral temperatures well above room temperatures. The plasmas created in this high-power helicon source (when light ions are employed) are ideally suited for fusion divertor plasma-material interaction studies and negative ion production for neutral beams.

Physics↗
DOE OSTI2021

Report on the Second MPEX User Research Forum

The Material Plasma Exposure eXperiment (MPEX) User Research Forum (MURF), a 2 day workshop, was held virtually on September 13–14, 2021, to seek community input for MPEX, a new high-power linear plasma device that is currently being built at Oak Ridge National Laboratory (ORNL). This was the second MURF workshop. The first MURF workshop was held in October 2019 in La Jolla, California, and focused exclusively on the definition of the surface analysis station for MPEX. MPEX is designed to address crucial R&D gaps in plasma material interactions (PMI) for future fusion reactors. The MPEX plasma source and heating systems will allow plasma exposures of plasma-facing materials and components to prototype fusion reactor divertor plasma conditions. The MPEX design accommodates the introduction of previously neutron-irradiated materials for fusion reactor-relevant plasma exposures. This capability will be unique worldwide. The US fusion program has advocated for such a device in numerous community reports in recent years, and now ORNL is building this new device. MPEX is a Major Item of Equipment project executed by the US Department of Energy’s Office of Science Fusion Energy Sciences.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Physical and technical basis of Materials Plasma Exposure eXperiment from modeling and Proto-MPEX results *

Abstract The Materials Plasma Exposure eXperiment (MPEX) is a steady-state linear plasma device that will address plasma-material interaction (PMI) science and enable testing of fusion reactor-relevant divertor plasma-facing materials. The MPEX source concept consists of a helicon plasma source to generate the plasma, electron cyclotron heating (ECH) for electron heating, and ion cyclotron heating (ICH) for ion heating. The MPEX source plasma is then transported axially to the PMI material target region to test material samples in fusion reactor-relevant divertor conditions. This paper will summarize the physical and technical basis of MPEX. The paper will first define the MPEX parameters and scenarios at the target relevant to PMI science for various fusion reactor-relevant divertor conditions and show plasma transport modeling results to set the MPEX source parameters. Recent experimental and modeling results from Proto-MPEX, a short-pulse experiment to develop the plasma production, heating, and transport physics for MPEX, will be shown. From these results, it will be shown that MPEX can reach its desired scenarios. The MPEX physical and technical basis will also determine important functional requirements for magnetic field, radiofrequency (RF) power, RF frequency, and neutral pressure in the helicon, ECH, ICH, and PMI regions that are required to achieve the desired MPEX scenarios. The necessity for key in-vessel components such as skimmers, limiters, and microwave absorbers will also be highlighted.

Lau, C. (ORCID:0000000285765867)↗
DOE OSTI2024

Changes in dislocation punching behavior due to hydrogen-seeded helium bubble growth in tungsten

The accumulation of gas atoms in tungsten is a topic of long-standing interest to the plasma-facing materials community due the metal's use as a divertor material in some tokamak fusion reactors. The nucleation and growth of He/H gas bubbles (along with their isotopes) can result from impinging fluxes of these gases which give rise to damage at the W divertor surface. The inclusion of He or H in W has been studied extensively by the community, finding that He bubbles modify the surface through periodic dislocation punching and bursting mechanisms while H bubbles impact the metal through plastic-strain induced material failure. However, the mechanisms which are present during the combined flux of both He and H is not well-studied atomistically. Motivated by this, an atomistic modeling study is conducted using molecular dynamics to assess the behavior of mixed concentration He:H bubbles in W. Here we find that the introduction of H into a growing He bubble results in a dramatic change in the nature and presence of dislocation loops which are typically generated via dislocation punching in over-pressurized He bubbles. Most notably, at high H concentrations, there is a switchover in energetic favorability from glissile 1/2<111> dislocations to sessile <100> dislocations. This thermodynamic crossover could imply a significant reduction in W surface morphology changes than with pure He bubbles and, additionally, we show this to have implications on the trapping of H in the bubbles and their associated dislocations.

36 MATERIALS SCIENCE↗
DOE OSTI2023

In-situ coating of silicon-rich films on tokamak plasma-facing components with real-time Si material injection

Abstract Experiments have been conducted in the DIII-D tokamak to explore the in-situ growth of silicon-rich layers as a potential technique for real-time replenishment of surface coatings on plasma-facing components (PFCs) during steady-state long-pulse reactor operation. Silicon (Si) pellets of 1 mm diameter were injected into low- and high-confinement (L-mode and H-mode) plasma discharges with densities ranging from 3.9– 7.5 × 10 19 m −3 and input powers ranging from 5.5 to 9 MW. The small Si pellets were delivered with the impurity granule injector at frequencies ranging from 4 to 16 Hz corresponding to mass flow rates of 5–19 mg s −1 (1– 4.2 × 10 20 Si s −1 ) at cumulative amounts of up to 34 mg of Si per five-second discharge. Graphite samples were exposed to the scrape-off layer and private flux region plasmas through the divertor material evaluation system to evaluate the Si deposition on the divertor targets. The Si II emission at the sample correlates with silicon injection and suggests net surface Si-deposition in measurable amounts. Post-mortem analysis showed Si-rich coatings containing silicon oxides, of which SiO 2 is the dominant component. No evidence of SiC was found, which is attributed to low divertor surface temperatures. The in-situ and ex-situ analysis found that Si-rich coatings of at least 0.4–1.2 nm thickness have been deposited at 0.4–0.7 nm s −1 . The technique is estimated to coat a surface area of at least 0.94 m 2 on the outer divertor. These results demonstrate the potential of using real-time material injection to form Si-enriched layers on divertor PFCs during reactor operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Conceptual design of HFIR irradiation experiment for material compatibility study on liquid Sn divertor

Liquid Sn is one of the promising coolants for liquid surface divertor concept of fusion reactors. However, the compatibility between liquid Sn and structural materials is an important issue that has to be addressed, because liquid Sn is extremely corrosive to steels at high temperatures. The corrosion may be mitigated when a protective Al2O 3 layer is formed on the surface of alumina forming steels. However, the effect of neutron irradiation on the integrity of protective layer is not made clear so far. Japan and US joint research project “FRONTIER” started in 2019 to investigate the material compatibility under neutron irradiation. The purpose of the present study is to develop the conceptual design of the irradiation test capsule which enables material compatibility tests for the alumina forming steels - liquid metal systems under neutron irradiation in the High Flux Isotope Reactor at Oak Ridge National Laboratory, TN, USA. The three dimensional drawing of capsule structure was then developed. The validity of the material selections for the capsule design was investigated by means of corrosion tests of SiC, Si3N4, Ti, and Mo in liquid Sn at 773 K for 262 hr.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2020

Nanoscale lattice strains in self-ion implanted tungsten

Developing a comprehensive understanding of the modification of material properties by neutron irradiation is important for the design of future fission and fusion power reactors. Self-ion implantation is commonly used to mimic neutron irradiation damage, however an interesting question concerns the effect of ion energy on the resulting damage structures. The reduction in the thickness of the implanted layer as the implantation energy is reduced results in the significant quandary: Does one attempt to match the primary knock-on atom energy produced during neutron irradiation or implant at a much higher energy, such that a thicker damage layer is produced? In this work, we address this question by measuring the full strain tensor for two ion implantation energies, 2 MeV and 20 MeV in self-ion implanted tungsten, a critical material for the first wall and divertor of fusion reactors. A comparison of 2 MeV and 20 MeV implanted samples is shown to result in similar lattice swelling. Multi-reflection Bragg coherent diffractive imaging (MBCDI) shows that implantation induced strain is in fact heterogeneous at the nanoscale, suggesting that there is a non-uniform distribution of defects, an observation that is not fully captured by micro-beam Laue diffraction. At the surface, MBCDI and high-resolution electron back-scattered diffraction (HR-EBSD) strain measurements agree quite well in terms of this clustering/non-uniformity of the strain distribution. However, MBCDI reveals that the heterogeneity at greater depths in the sample is much larger than at the surface. This combination of techniques provides a powerful method for detailed investigation of the microstructural damage caused by ion bombardment, and more generally of strain related phenomena in micro-volumes that are inaccessible via any other technique.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Novel SOLPS-ITER simulations of X-point target and snowflake divertors

Abstract The design and understanding of alternative divertor configurations may be crucial for achieving acceptable steady-state heat and particle material loads for magnetic confinement fusion reactors. Multiple X-point alternative divertor geometries such as snowflakes and X-point targets have great potential in reducing power loads, but have not yet been simulated widely in codes with kinetic neutrals. This paper discusses recent changes made to the SOLPS-ITER code to allow for the simulation of X-point target and low-field side snowflake divertor geometries. Snowflake simulations using this method are presented, in addition to the first SOLPS-ITER simulation of the X-point target. Analysis of these results show reasonable consistency with the simple modelling and theoretical predictions, supporting the validity of the methodology implemented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

MPEX AI Digital Twins

All magnetically confined plasma fusion power plant concepts (Tokamak, Spherical Tokamak, Stellarator, Mirror, ...) must exhaust the heat and plasma from the core confinement region to the material walls. The primary channel for this exhaust is through a plasma divertor which directs plasma along open magnetic field lines to a material target. The Material Plasma Exposure eXperiment (MPEX) illustrated in Figure 1, is a high-power, steady-state linear plasma device designed to produce the plasma material interaction (PMI) conditions of the divertor of future magnetic confinement fusion power plants: energy flux 20MW/m 2 , ion fluence 1031/m 2 , pulse duration 106 sec. These goals of plasma exposure in MPEX are well beyond those achieved in magnetic fusion experimental devices. Successfully achieving these high power steady state conditions for long pulses requires operational control of the heating and particle sources and the plasma flux to the walls and target. The MPEX AI Hot Spot Controller, proposed in this project, will help achieve the operational milestones of MPEX. The MPEX device will begin commissioning at the end of FY26. A smaller proto-MPEX was operated for 14,666 plasma discharges and will resume operation in September of 2025 as proto-MPEX-lite, with reduced capability, to test a new window for the Helicon plasma source. The proto-MPEX data has undergone surrogate modeling with machine learning methods (R. Archibald, 2022 IEEE International Conference on Big Data). This proto-MPEX data will be used to begin development of the AI digital twins described in this white paper. The scientific mission of MPEX is to qualify materials of different composition for use in the high energy and plasma flux conditions of a fusion power plant. The materials exposed in MPEX will in some cases be exposed to high neutron fluxes at other ORNL facilities to measure the changes to their PMI properties. The targets exposed in MPEX will be transported under vacuum to a Surface Analysis Station (SAS). The SAS will be equipped with the following diagnostics: Focused Ion Beam (FIB) for trench milling, 100-400 angstrom resolution scanning electron microscope (SEM), surface mapping x-ray spectrometer, high resolution camera, and a future upgrade to a laser induced breakdown spectroscopy quadruple mass spectrometer (LIBS-QMS). The MPEX experiments will generate diverse pre- and post-exposure measurement data of detailed material properties down to the crystal grain level in 3D for post-exposure assessment of PMI damage (e.g. cracking, melting, erosion and redeposition of the material). Physics models for the PMI, and how the material composition and manufacturing impact its performance under high energy plasma exposure, need to be validated with MPEX data to guide the selection of new candidate materials. Our vision for the MPEX AI Digital Twins project is to supply experimental and physics model simulation data to train Artificial Intelligence (AI) models for data processing, analysis, operational control, PMI and materials simulation to maximize the scientific output of the MPEX device. Ultimately, an AI digital twin of MPEX material assessment metrics for tested and synthetic material types with simulated PMI will be trained by the AI Modeling Teams on the experimental and physics simulation data submitted to the American Science Cloud by this project. A purely empirical search for the best material is inefficient given the finite number of samples that can be tested on MPEX. In order to expand the material properties database for training the MPEX Material Assessment AI Digital Twin, and to gain physics understanding of the PMI processes, physics models of the material properties and PMI processes are required. The physics simulations provide detailed simulation data, like impact angles for plasma ions, sputtering yields, transport of the ionized sputtered target material in the plasma, and redeposition locations. This simulation data expands the measurement data for deeper physics understanding. The experimental data is essential to validate the PMI and material structure simulation models. The validated models can then be used to generate new simulation data of MPEX material assessments for synthetic material compositions that have not been exposed in MPEX. These predictive simulations, plus the whole experimental dataset, will be used to train the MPEX Material Assessment AI Digital Twin allowing a rapid generative AI search for new materials with reduced PMI damage by interpolating the domain of the training set. These new optimum materials can be simulated with the physics codes and/or tested in MPEX. The ability of AI neural networks to interpolate multi-dimensional parameter spaces and generate virtual data is exploited for a more efficient search for optimum materials. The advent of the Transformational AI Models Consortium (TAIMC) is an opportunity to engage with state of the art private and public AI developers to achieve the goals of the AI digital twins and AI accelerated physics models proposed in this project. Our partners at ORNL from the Advance Scientific Computing Research (ASCR) organization will collaborate in accelerating the integrated plasma material interaction simulation framework. This simulation framework will provide a platform for generating simulation data across a range of physical fidelities, including hybrid methods that produce multi-fidelity results. This data will be leveraged for AI model development, both for generation of surrogates and the automation of simulation campaigns. A part of the research below will include collaborative efforts with the TAIMC to (i) adapt data storage approaches to ensure AI-readiness, (ii) provide a protypical exemplar to inform and exercise constructed workflows, and (iii) generate and share data, using the TAIMC unified AI data standard, for foundational models that will be trained from multiple sources across the DOE complex. We will also collaborate with the TAIMC, as well as the planned AI modeling teams, to develop approaches for reducing the cost of data generation. These include tailored multi-fidelity approaches as well as fine-tuning strategies to augment general, large-scale foundational models.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Parallel transport modeling of linear divertor simulators with fundamental ion cyclotron heating *

Abstract The Material Plasma Exposure eXperiment (MPEX) is a steady state linear device with the goal to perform plasma material interaction studies at future fusion reactor relevant conditions. A prototype of MPEX referred as ‘Proto-MPEX’ is designed to carry out research and development related to source, heating and transport concepts on the planned full MPEX device. The auxiliary heating schemes in MPEX are based on cyclotron resonance heating with radio frequency (RF) waves. Ion cyclotron heating (ICH) and electron cyclotron heating in MPEX are used to independently heat the ions and electrons and provide fusion divertor conditions ranging from sheath-limited to fully detached divertor regimes at a material target. A hybrid particle-in-cell code- PICOS++ is developed and applied to understand the plasma parallel transport during ICH in MPEX/Proto-MPEX to the target. With this tool, evolution of the distribution function of MPEX/Proto-MPEX ions is modeled in the presence of (a) Coulomb collisions, (b) volumetric particle sources and (c) quasi-linear RF-based ICH. The code is benchmarked against experimental data from Proto-MPEX and simulation data from B2.5 EIRENE. The experimental observation of ‘density-drop’ near the target in Proto-MPEX and MPEX during ICH is demonstrated and explained via physics-based arguments using PICOS++ modeling. In fact, the density drops at the target during ICH in Proto-MPEX/MPEX to conserve the flux and to compensate for the increased flow during ICH. Furthermore, sensitivity scans of various plasma parameters with respect to ICH power are performed for MPEX to investigate its role on plasma transport and particle and energy fluxes at the target.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Liquid lithium divertor analysis using coupled plasma material interaction model

A liquid lithium divertor can improve performance of future fusion devices by creating efficient power exhaust and improving the energy confinement via pumping of the hydrogen isotopes. In addition, significantly higher heat fluxes can be handled if controlled vapor shielding is used to redistribute the divertor heat flux over a wider area. Design and optimization of such a system calls for an analysis model which includes a strong two-way coupling between the plasma and divertor material. The incoming plasma heat and particle flux will affect the divertor surface temperature, which is a defining factor of the lithium evaporative and sputtered flux going into the plasma. Results of the coupled model based on the plasma edge code SOLPS-ITER and the computational fluid dynamics (CFD) code ANSYS-CFX will be presented for different configurations. An analytical slab flow model is used as a heat transfer boundary condition for SOLPS, defining particle flux from the wall via calculation of the surface temperature. At the final step, results of the SOLPS analysis are verified using a 3D CFD magnetohydrodynamics (MHD) analysis which uses heat and particle flux from SOLPS as a boundary condition. In addition to plasma heat flux, both analytical and CFD temperature models include several plasma material interaction effects, such as lithium evaporation, condensation and sputtering based on deuterium target flux. New adatom sputtering model based on the available experimental data is presented. Analytical model is expanded to include free surface axisymmetric configurations. Results of parametric studies of the divertor configurations with different lithium inlet temperature and velocity will be presented leading to the optimal design resulting in the lowest possible lithium contamination in the core.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Liquid lithium as divertor material to mitigate severe damage of nearby components during plasma transients

The successful operation of thermonuclear fusion reactors such as ITER, DEMO, and future commercial plants is mainly determined by the optimum choice of materials for various components. The objective of this work is to accurately and comprehensively simulate the entire device in 3D to predict pros and cons of various materials, e.g., liquid lithium in comparison to tungsten and carbon to predict future ITER-like and DEMO divertor performances. We used our comprehensive HEIGHTS simulation package to investigate ITER-like components response during transient events in exact 3D geometry. Starting from the lost hot core plasma particles through SOL, deposition on the divertor surface, and the generation of secondary plasma of divertor materials. Our simulations predicted significant reduction in the heat loading and damage to the divertor nearby and internal components in the case when lithium is used on the divertor plates. While if tungsten or carbon are used on the divertor plate, significant melting areas and vaporization spots can occur (less for carbon) on the reflector, dome, and stainless steel tubes, and even parts of the first walls can melt due to the high radiation power of the secondary divertor plasma. Lithium photon radiation deposition into the divertor and nearby surfaces was decreased by two orders of magnitude compared to tungsten and by one order of magnitude compared to carbon. This analysis showed that using liquid lithium for ITER-like surfaces and future DEMO can lead to significant enhancement in components lifetime.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Directed energy deposition of functionally graded V-4Cr-4Ti to Fe-9Cr transition for fusion power systems

This study proposes a graded structure via additive manufacturing for divertor and first wall blanket applications in fusion reactors. Materials were selected based on thermodynamic calculations to operate from 1100 °C at the plasma-facing level to 550 °C at the structural steel level. Conventional joining methods often lead to failures due to discrete reaction layers with significant mechanical property differences. Using laser beam-directed energy deposition (LB-DED), this study demonstrates the fabrication of a VCrTi-Gr91 steel functionally graded component through a novel process parameter optimization framework. A systematic approach included powder characterization, single-track depositions, and construction of printability maps. Near full-density specimens of each interlayer were additively manufactured, and a transition from V-based alloys to reduced activation ferritic martensitic steels was achieved. Computational material selection of interlayer alloys and thermodynamic/diffusion kinetics simulations prevented most interface incompatibilities. A brittle intermetallic formed at one interface, causing cracking, which was not predicted by current thermodynamic models. Transition alloy design approach was updated with a more recent database and a mitigation strategy has been proposed to eliminate the formation of deleterious intermetallic phases. Ultimately, LB-DED has proven effective for producing multi-material graded systems for fusion applications, with the demonstrated process parameter optimization framework applicable to various materials.

Additive manufacturing↗