Search NASA⌕ Search

SEARCH · Search NASA

Results for “divertor damage”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Detecting divertor damage during steady state operation of Wendelstein 7-X from thermographic measurements

Wendelstein 7-X (W7-X) aims to demonstrate the reactor capability of the stellarator concept, by creating plasmas with pulse lengths of up to 30 min at a heating power of up to 10 MW. The divertor plasma facing components will see convective steady state heat flux densities of up to 10 MW/m 2 . These high heat flux target elements are actively cooled and are covered with carbon fibre reinforced carbon (CFC) as plasma facing material. The CFC is bonded to the CuCrZr cooling structure. Over the life time of the experiment this interface may weaken and cracks can occur, greatly reducing the heat conduction between the CFC tile and the cooling structure. Furthermore, there is not only the need to monitor the divertor to prevent damage by overheating but also the need to detect these fatigue failures of the interface. A method is presented for an early detection of fatigue failures of the interface layer, solely by using the information delivered by the IR-cameras monitoring the divertor. This was developed and validated through experiments made with high heat flux target elements prior to installation in W7-X.

47 OTHER INSTRUMENTATION↗

Retention properties in displacement damaged ultra-fine grain tungsten exposed to divertor plasma

One of the main advantages of using tungsten (W) as a plasma facing material (PFM) is its low uptake and retention of tritium. However, in high purity (ITER grade) W, hydrogenic retention increases significantly with neutron-induced displacement damage in the W lattice. This experiment examines an alternative W grade PFM, ultra-fine grain (UFG) W, to compare its retention properties with ITER grade W after 12 MeV Si ion displacement damage up to 0.6 dpa (displacements per atom.) Following exposure to plasma in the DIII-D divertor, D retention was then assessed with Nuclear Reaction Analysis (NRA) depth profiling up to 3.5 µm and thermal desorption spectrometry (TDS). Undamaged specimens were also included in our test matrix for comparison. For all samples, D release peaks were observed during TDS at approximately 200 °C and 750 °C. For the ITER-grade W specimens, the intensity of the 750 °C release peak was more pronounced for specimens that had been pre-damaged. Conversely, UFG samples that had been damaged by 12 MeV Si showed enhancement of the lower temperature release peak (200 °C). NRA profiles also reveal a higher D concentration for UFG W samples up to the peak in the damage profile at a depth of 2 m. Overall, we observed that the total trapped inventory in UFG W was 20% higher than ITER grade W in the undamaged case and 10% higher in the damaged case. A comparison of NRA and TDS data indicates that a larger fraction of the total retained D is trapped near the surface (86–100%) in UFG W pre-damaged to 0.6 dpa compared with ITER grade W (39–61%). Further examination of the UFG material with microscopy is recommended for a definitive determination of the types of defects responsible for D trapping. Our results highlight some potential trade-offs associated UFG W regarding its performance from a tritium retention standpoint. That said, our TDS results indicate that this enhanced inventory can be released by baking at relatively low temperatures (<500 °C), providing an avenue for minimizing tritium retention in this material that would be practical for implementation in a tokamak.

Barton, J↗

Real-time radiative divertor feedback control development for the NSTX-U tokamak using a vacuum ultraviolet spectrometer

A radiative divertor technique is planned for the NSTX-U tokamak to prevent excessive erosion and thermal damage of divertor plasma-facing components in H-mode plasma discharges with auxiliary heating up to 12 MW. In the radiative (partially detached) divertor, extrinsically seeded deuterium or impurity gases are used to increase plasma volumetric power and momentum losses. A real-time feedback control of the gas seeding rate is planned for discharges of up to 5 s duration. The outer divertor leg plasma electron temperature T{sub e} estimated spectroscopically in real time will be used as a control parameter. A vacuum ultraviolet spectrometer McPherson Model 251 with a fast charged-coupled device detector is developed for temperature monitoring between 5 and 30 eV, based on the Δn = 0, 1 line intensity ratios of carbon, nitrogen, or neon ion lines in the spectral range 300–1600 Å. A collisional-radiative model-based line intensity ratio will be used for relative calibration. A real-time T{sub e}-dependent signal within a characteristic divertor detachment equilibration time of ∼10–15 ms is expected.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Liquid lithium as divertor material to mitigate severe damage of nearby components during plasma transients

The successful operation of thermonuclear fusion reactors such as ITER, DEMO, and future commercial plants is mainly determined by the optimum choice of materials for various components. The objective of this work is to accurately and comprehensively simulate the entire device in 3D to predict pros and cons of various materials, e.g., liquid lithium in comparison to tungsten and carbon to predict future ITER-like and DEMO divertor performances. We used our comprehensive HEIGHTS simulation package to investigate ITER-like components response during transient events in exact 3D geometry. Starting from the lost hot core plasma particles through SOL, deposition on the divertor surface, and the generation of secondary plasma of divertor materials. Our simulations predicted significant reduction in the heat loading and damage to the divertor nearby and internal components in the case when lithium is used on the divertor plates. While if tungsten or carbon are used on the divertor plate, significant melting areas and vaporization spots can occur (less for carbon) on the reflector, dome, and stainless steel tubes, and even parts of the first walls can melt due to the high radiation power of the secondary divertor plasma. Lithium photon radiation deposition into the divertor and nearby surfaces was decreased by two orders of magnitude compared to tungsten and by one order of magnitude compared to carbon. This analysis showed that using liquid lithium for ITER-like surfaces and future DEMO can lead to significant enhancement in components lifetime.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Real-time Radiative Divertor Feedback Control Development for the NSTX-U Tokamak using a Vacuum Ultraviolet Spectrometer

A radiative divertor technique is planned for the NSTX-U tokamak to prevent excessive erosion and thermal damage of divertor plasma-facing components in H-mode plasma discharges with auxiliary heating up to 12 MW. In the radiative (partially detached) divertor, extrinsically seeded deuterium or impurity gases are used to increase plasma volumetric power and momentum losses. A real-time feedback control of the gas seeding rate is planned for discharges of up to 5 s duration. The outer divertor leg plasma electron temperature Te estimated spectroscopically in real time will be used as a control parameter. A vacuum ultraviolet spectrometer McPherson Model 251 with a fast charged-coupled device detector is developed for temperature monitoring between 5 and 30 eV, based on the delta n=0;1 line intensity ratios of carbon, nitrogen or neon ions lines in the spectral range 300 to 1600 A. A collisional-radiative model-based line intensity ratio will be used for relative calibration. A real-time Te-dependent signal within a characteristic divertor detachment equilibration time of ~ 10 -15 ms is expected.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Influence of electronic effects on the surface erosion of tungsten

Tungsten is a strong contender for a plasma-facing material in future fusion power plant designs, and the material of choice for the divertor of ITER, due to its high melting point, thermal conductivity, and resistance to sputtering erosion. Sputtering erosion is a major concern for plasma-facing materials because sputtered atoms could enter the plasma and result in cooling. Atomistic modeling, using molecular dynamics, has previously been successful in identifying fundamental mechanisms of surface damage caused by ion bombardment. The damage has been found to be particularly sensitive to the rate of energy dissipation but energy transport is not well described in classical molecular dynamics simulations of metals. We present a methodology for including a realistic description of electronic energy absorption, transport, and redistribution in molecular dynamics simulations of self sputtering. The results for three different 5 keV self-sputtering events are presented for four distinct thermal transport models. The results demonstrate the sensitivity of surface damage to the model used to describe the electronic thermal transport.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Demonstration of Super-X divertor exhaust control for transient heat load management in compact fusion reactors

Nuclear fusion could offer clean, abundant energy. However, managing the power exhausted from the core fusion plasma towards the reactor wall remains a major challenge. This is compounded in emerging compact reactor designs promising more cost-effective pathways towards commercial fusion energy. Alternative Divertor Configurations (ADCs) are a potential solution. In this work, we demonstrate exhaust control in ADCs, employing a novel method to diagnose the neutral gas buffer, which shields the target. Our work on the Mega Ampere Spherical Tokamak Upgrade shows that ADCs tackle key risks and uncertainties for fusion energy. Their highly reduced sensitivity to perturbations enables active exhaust control in otherwise unfeasible situations and facilitates an increased passive absorption of transients, which would otherwise damage the divertor. We observe a strong decoupling of each divertor from other reactor regions, enabling near-independent control of the divertors and core plasma. Our work showcases the real-world benefits of ADCs for effective heat load management in fusion power reactors.

Imaging techniques↗

Comparison of heat flux measurement techniques during the DIII-D metal ring campaign

The heat fluxes expected in the ITER divertor raise concerns about the damage tolerances of tungsten, especially due to thermal transients caused by edge localized modes (ELMs) as well as frequent temperature cycling from high to low extremes. Thus we are motivated to understand the heat flux conditions that can cause not only enhanced erosion but also bulk thermo-mechanical damage to a tungsten divertor. For the metal ring campaign in DIII-D, tungsten-coated TZM tile inserts were installed making two toroidal arrays of metal tile inserts in the lower divertor. This study examines the deposited heat flux on these rings with embedded thermocouples (TCs) sampling at 10 kHz and compares them to Langmuir probe (LP) and infrared thermography (IRTV) heat flux measurements. We see agreement of the TC, LP, and IRTV data within 20% of the heat flux averaged over the entire discharge, and that all three diagnostics suggest parallel heat flux at the OSP location increases linearly with input heating power. The TC and LP heat flux time traces during the discharge trend together during large changes to the average heat flux. By subtracting the LP measured inter-ELM heat flux from TC data, using a rectangular ELM energy pulse shape, and taking the relative size and duration of each ELM from ${{D}}_{\alpha }$ measurements, we extract the ELM heat fluxes from TC data. This over-estimates the IRTV measured ELM heat fluxes by a factor of 1.9, and could be due to the simplicity of the TC heat flux model and the assumed ELM energy pulse shape. ELM heat fluxes deposited on the inserts are used to model tungsten erosion in this campaign. These TC ELM heat flux estimates are used in addition to IRTV, especially in cases where the IRTV view to the metal ring is obstructed. We observe that some metal inserts were deformed due to exposed leading edges. The thermal conditions on these inserts are investigated with the thermal modeling code ABAQUS using our heat flux measurements when these edges were exposed. We report on how the thermal cycling on the ends of the inserts caused this deformation.

42 ENGINEERING↗

The influence of displacement damage on deuterium retention in tungsten exposed to divertor plasma in DIII-D.

Experiments were conducted to determine the influence of displacement damage on retention of deuterium in tungsten plasma-facing components in a tokamak. Tungsten samples, previously damaged by ion irradiation, were exposed to the outer strike point of attached H-mode plasmas in DIII-D. Nuclear reaction analysis (NRA) was used to measure the depth profile of deuterium retained in the tungsten. Displacement damage increased the concentration of retained deuterium to the maximum depth (about 2.5 {micro}m) of the damage, to concentrations up to 0.003 D/W, compared to D/W < 10{sup -5} in undamaged W. Tungsten coverage on adjacent carbon surfaces of the probe was mapped by Rutherford backscattering, giving the average tungsten erosion rate and spatial variation of redeposition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A new discovery of edge localized modes suppression using ICRH

Here, the high-confinement mode (H-mode) is very important for the fusion performance of ITER and future fusion reactors. The H-mode pedestal is a region featuring strongly reduced turbulence and transport just inside the limiting flux surface with strong plasma gradients, which drive edge localized modes (ELMs) in tokamaks. The ELMs, however, are quasiperiodic relaxations of the pedestal, resulting in a series of hot plasma eruptions similar to magnetospheric substorms, solar and stellar flares, which could potentially damage the ITER divertor plates and first walls. To mitigate and suppress the ELMs in H-mode plasmas, the fusion community has tried to develop effective actuators over the past two decades. Two separate excellent inventions have been awarded to recognize their achievements. The 2018 APS excellence award in Plasma Physics Research was given to Drs. Todd E. Evans, Max E. Fenstermacher, and Richard Alan Moyer for their first experimental demonstration of the stabilization of ELMs in high-confinement diverted discharges by application of very small edge-resonant magnetic perturbations, which led to the adoption of suppression coils in the ITER design. The 2018 Fusion Technology Award from the IEEE’s Nuclear and Plasma Science Society (NPSS) was given to Dr. Larry Baylor for his work designing the fueling, pumping and disruption mitigation system for the US ITER Project and for the implementation of pellet ELM mitigation for ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Microwave Imaging Reflectometry for the study of Edge Harmonic Oscillations on DIII-D [Microwave Imaging Reflectometry (MIR) for the study of Edge Harmonic Oscillations (EHOs) on DIII-D]

Quiescent H-mode (QH) is an ELM free mode of operation in which edge-localized harmonic oscillations (EHOs) are believed to enhance particle transport, thereby stabilizing ELMs and preventing damage to the divertor and plasma facing components. Microwave Imaging Reflectometer (MIR) enabling direct comparison between the measured and simulated 2D images of density fluctuations near the edge can determine the 2D structure of density oscillation which can help to explain the physics behind EHO modes. MIR data sometimes indicates a counter-propagation between higher (n>1) and dominant (n=1) harmonics of coherent EHOs in the steep gradient regions of the pedestal. To preclude diagnostic artifacts, we have performed forward modeling that includes possible optical misalignments to show that offsets between transmitting and receiving antennas do not account for this feature. We have also simulated the non-uniform rotation of the EHO structure, which induces multiple harmonics that are properly characterized in the synthetic diagnostic. Excluding these possible explanations for the data, the counter-propagation observed in MIR data, which is not corroborated by external Mirnov coil array measurements, may be due to subtleties of the eigenmode structure, such as an inversion radius consistent with a magnetic island. Similar effects are observed in analysis of internal ECE-Imaging and BES data. Furthermore, the identification of a non-ideal structure motivates further exploration of nonlinear models of this instability.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Changes in dislocation punching behavior due to hydrogen-seeded helium bubble growth in tungsten

The accumulation of gas atoms in tungsten is a topic of long-standing interest to the plasma-facing materials community due the metal's use as a divertor material in some tokamak fusion reactors. The nucleation and growth of He/H gas bubbles (along with their isotopes) can result from impinging fluxes of these gases which give rise to damage at the W divertor surface. The inclusion of He or H in W has been studied extensively by the community, finding that He bubbles modify the surface through periodic dislocation punching and bursting mechanisms while H bubbles impact the metal through plastic-strain induced material failure. However, the mechanisms which are present during the combined flux of both He and H is not well-studied atomistically. Motivated by this, an atomistic modeling study is conducted using molecular dynamics to assess the behavior of mixed concentration He:H bubbles in W. Here we find that the introduction of H into a growing He bubble results in a dramatic change in the nature and presence of dislocation loops which are typically generated via dislocation punching in over-pressurized He bubbles. Most notably, at high H concentrations, there is a switchover in energetic favorability from glissile 1/2<111> dislocations to sessile <100> dislocations. This thermodynamic crossover could imply a significant reduction in W surface morphology changes than with pure He bubbles and, additionally, we show this to have implications on the trapping of H in the bubbles and their associated dislocations.

36 MATERIALS SCIENCE↗

Conceptual design study for heat exhaust management in the ARC fusion pilot plant

The ARC pilot plant conceptual design study has been extended beyond its initial scope to explore options for managing ∼525 MW of fusion power generated in a compact, high field (B 0 = 9.2 T) tokamak that is approximately the size of JET (R 0 = 3.3 m). Taking advantage of ARC’s novel design – demountable high temperature superconductor toroidal field (TF) magnets, poloidal magnetic field coils located inside the TF, and vacuum vessel (VV) immersed in molten salt FLiBe blanket – this follow-on study has identified innovative and potentially robust power exhaust management solutions. The superconducting poloidal field coil set has been reconfigured to produce double-null plasma equilibria with a long-leg X-point target divertor geometry. Here this design choice is motivated by recent modeling which indicates that such configurations enhance power handling and may attain a passively-stable detachment front that stays in the divertor leg over a wide power exhaust window. A modified VV accommodates the divertor legs while retaining the original core plasma volume and TF magnet size. The molten salt FLiBe blanket adequately shields all superconductors, functions as an efficient tritium breeder, and, with augmented forced flow loops, serves as an effective single-phase, low-pressure coolant for the divertor, VV, and breeding blanket. Advanced neutron transport calculations (MCNP) indicate a tritium breeding ratio of ∼1.08. The neutron damage rate (DPA/year) of the remote divertor targets is ∼3–30 times lower than that of the first wall. The entire VV (including divertor and first wall) can tolerate high damage rates since the demountable TF magnets allow the VV to be replaced every 1–2 years as a single unit, employing a vertical maintenance scheme. A tungsten swirl tube FLiBe coolant channel design, similar in geometry to that used by ITER, is considered for the divertor heat removal and shown capable of exhausting divertor heat flux levels of up to 12 MW/m 2 . Several novel, neutron tolerant diagnostics are explored for sensing power exhaust and for providing feedback control of divertor conditions over long time scales. These include measurement of Cherenkov radiation emitted in FLiBe to infer DT fusion reaction rate, measurement of divertor detachment front locations in the divertor legs with microwave interferometry, and monitoring “hotspots” on the divertor chamber walls via IR imaging through the FLiBe blanket.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Active Lithium Injection for a Real Time Control of the Divertor Heat Flux for Fusion Devices

When the local heat flux exceeds specified flux limit, tungsten PFC surfaces can be damaged, which is not acceptable for a reliable reactor operations. The divertor PFCs are typically designed for a specific heat flux limit usually assuming an average steady-state heat flux which is typically 5–10 MW/m 2 . However, in addition to steady-state heat flux, fusion reactor divertor PFCs could experience transient heat fluxes such as ELMs and/or other magnetic reconnection events which can deposit large transient heat fluxes onto the divertor PFCs. The transient divertor heat flux could be significantly larger than the steady-state heat flux which could damage the solid PFC surfaces. The divertor heat flux can be subjected to additional complications such as the uncertainties in the the divertor strike point heat flux projection. Moreover, there are additional experimental observations of non-axisymmetric power flux which can occur under non-axisymmetric magnetic perturbations. The liquid lithium (LL) PFCs is more resilient against such transient heat fluxes as they could evaporate LL as needed and the lost LL can be then replenished afterward. In this paper, we analyze a case for a transient divertor heat pulse of 1 MJ in 10 ms for a ITER-size reactor. This is a small perturbation (~ 0.1%) to the expected plasma stored energy compared to the previously analyzed case of 20 MJ heat pulse. Even with this relatively modest heat pulse, the LL surface undergoes ~ 100 °C temperature rise. However, the resulting LL surface heating without rapid cooldown mechanism could lead to excessive LL evaporation continuing well after the transient heat flux resulting in a significant Li injection of ~ 0.6 mol in about a 200 ms period. This amount of Li injection could cause plasma dilution and performance degradation. On the other hand, an active Li injection capability if optimized could prevent the LL surface temperature rise and thus reducing subsequent Li evaporation into the plasma by a factor of 7 compared to the passive LL PFC case. A crucial tool of active Li injection is a rapid response pellet injector which could inject light impurity pellets before the excessive heat flux could reach the divertor plate causing serious damage. A simple pellet ablation model suggests a favorable pellet deposition profile for smaller ~ 0.1 mm radius pellet with ~ 10–20 m/s velocity. Moreover, if it is possible to inject from the private flux region, the pellet injection efficiency into the high heat flux strike point region can be as high as 80% compared to ~ 50% for the injection from outer radius region. The pellet deposition efficiency can be further improved by designing a shell-pellet which can burst when a certain ablation fraction is reached. Finally, a possible implementation technique using an inductive pellet injector with a rapid time response of a few msec is proposed here which can be tested in NSTX-U.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Thermal Analysis to Calculate the Vessel Temperature and Stress in Alcator C-Mod Due to the Divertor Upgrade

Alcator C-Mod is planning an upgrade to its outer divertor. The upgrade is intended to correct the existing outer divertor alignment with the plasma, and to operate at elevated temperatures. Higher temperature operation will allow study of edge physics behavior at reactor relevant temperatures. The outer divertor and tiles will be capable of operating at 600oC. Longer pulse length, together with the plasma and RF heat of 9MW, and the inclusion of heater elements within the outer divertor produces radiative energy which makes the sustained operation much more difficult than before. An ANSYS model based on ref. 1 was built for the global thermal analysis of C-Mod. It models the radiative surfaces inside the vessel and between the components, and also includes plasma energy deposition. Different geometries have been simulated and compared. Results show that steady state operation with the divertor at 600oC is possible with no damage to major vessel internal components. The differential temperature between inner divertor structure, or "girdle" and inner vessel wall is ~70oC. This differential temperature is limited by the capacity of the studs that hold the inner divertor backing plates to the vessel wall. At a 70oC temperature differential the stress on the studs is within allowable limits. The thermal model was then used for a stress pass to quantify vessel shell stresses where thermal gradients are significant.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗