Search NASA⌕ Search

SEARCH · Search NASA

Results for “divertor simulator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Study of detached plasma profile in the divertor simulation experimental module of tandem mirror GAMMA 10/PDX

A divertor simulation experimental module (D-module) in the tandem mirror GAMMA 10/PDX was used for the study of plasma detachment. In previous studies, it was difficult to measure far-upstream plasma parameters in the D-module, and only electrostatic probes on the target plate were used to perform electron temperature and density measurements. Furthermore, to study the detached plasma structure, a Thomson scattering (TS) system and a microwave interferometer system have been installed to measure the inside plasma parameters of the D-module, and a movable electrostatic probe has been placed at the inlet of the D-module to measure the inlet plasma density and temperature. The TS system in the central cell observed the electron temperature and density of the core plasma simultaneously. These measurements revealed the entire density and temperature structure from the core plasma to the divertor plate. The line average electron density measured by the microwave interferometer showed a rollover behavior during detachment. The results indicated that the ionization region was located around the center of the D-module, and it appears to move upstream along the axis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Parallel transport modeling of linear divertor simulators with fundamental ion cyclotron heating *

Abstract The Material Plasma Exposure eXperiment (MPEX) is a steady state linear device with the goal to perform plasma material interaction studies at future fusion reactor relevant conditions. A prototype of MPEX referred as ‘Proto-MPEX’ is designed to carry out research and development related to source, heating and transport concepts on the planned full MPEX device. The auxiliary heating schemes in MPEX are based on cyclotron resonance heating with radio frequency (RF) waves. Ion cyclotron heating (ICH) and electron cyclotron heating in MPEX are used to independently heat the ions and electrons and provide fusion divertor conditions ranging from sheath-limited to fully detached divertor regimes at a material target. A hybrid particle-in-cell code- PICOS++ is developed and applied to understand the plasma parallel transport during ICH in MPEX/Proto-MPEX to the target. With this tool, evolution of the distribution function of MPEX/Proto-MPEX ions is modeled in the presence of (a) Coulomb collisions, (b) volumetric particle sources and (c) quasi-linear RF-based ICH. The code is benchmarked against experimental data from Proto-MPEX and simulation data from B2.5 EIRENE. The experimental observation of ‘density-drop’ near the target in Proto-MPEX and MPEX during ICH is demonstrated and explained via physics-based arguments using PICOS++ modeling. In fact, the density drops at the target during ICH in Proto-MPEX/MPEX to conserve the flux and to compensate for the increased flow during ICH. Furthermore, sensitivity scans of various plasma parameters with respect to ICH power are performed for MPEX to investigate its role on plasma transport and particle and energy fluxes at the target.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Simulations of divertor heat flux width using transport code with cross-field drifts under the BOUT++ framework

The fluid transport code [trans-electric field (Er) module] under the BOUT++ framework has been used to simulatedivertor heat flux width and boundary Er with all drifts and the sheath potential in the scrape-off layer. The calculated steady state radial Er in the pedestal region has been compared with that of experimental measurements from the Alcator C-Mod tokamak. The magnitude and shape of Er are similar to those of the experimental data. In order to understand the relative role of cross-field drifts vs turbulent transport in setting the heat flux width, four C-Mod enhanced Dα H-mode discharges with a lower single null divertor configuration should be simulated. BOUT++ transport simulations with cross-field drifts included yield similar heat flux width λq to that of experimental measurements (within a factor of 2) from both the probe and the surface thermocouple diagnostics and show a similar trend with plasma current to that of the Eich experimental scaling. The simulations show that both drifts and turbulent transport compete to determine the heat flux width. The magnetic drifts play a dominant role in setting the divertor heat-flux width, while the E × B drift decreases the heat flux width by 10%–25%, leading to improved agreement with the experiment relative to Goldston’s model. A turbulence diffusivity scan (χ) identifies two distinct regimes: a drift dominant regime when χ is small and a turbulence dominant regime when χ is large. The Goldston heuristic drift model yields a lower limit of the width λq.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Simulations of divertor plasmas with inverse sheaths

The effect of strong electron emission from material surfaces has been proposed to form an “inverse sheath”: a region with a positive potential relative to the near-wall plasma which prevents the flow of ions to the wall [M. D. Campanell, “Negative plasma potential relative to electronemitting surfaces,” Phys. Rev. E. 88, 033103 (2013); M. D. Campanell and M. V. Umansky, “Strongly emitting surfaces unable to float below plasma potential,” Phys. Rev. Lett. 116, 1–5 (2016); M. D. Campanell and G. R. Johnson, “Thermionic cooling of the target plasma to a sub-ev temperature,” Phys. Rev. Lett. 122, 1–5 (2019)]. We assess the viability of this regime in a tokamak device using the 2D edge plasma transport code UEDGE [T. Rognlien et al ., “A fully implicit, time dependent 2-D fluid code for modeling tokamak edge plasmas,” J. Nucl. Mater. 196–198, 347–351 (1992)]. Since the UEDGE code does not consider the sheath region directly, we apply boundary conditions at the divertor targets which emulate the physics of both “standard” and “inverse” sheath regimes [R. Masline et al ., “Influence of the inverse sheath on divertor plasma performance in tokamak edge plasma simulations,” Contrib. Plasma Phys. 60, e201900097 (2020)]. Using these boundary conditions, we perform scoping studies to assess plasma parameters near the target by varying the density at the core-edge interface. We observe a smooth transition in the resultant profiles of plasma parameters for the standard sheath, and a bifurcation across the simulation set for plasmas with an inverse sheath. The cause of this bifurcation is assessed by performing the parameter scan both with and without impurity radiation; we observe that the bifurcation persists in both cases, indicating that this bifurcation is caused by plasma recombination.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Implementation of a 9-point stencil in SOLPS-ITER and implications for Alcator C-Mod divertor plasma simulations

The SOLPS-ITER code suite is used worldwide for plasma edge modeling, the interpretation of experiments, as well as for the design of the ITER divertor. The numerical scheme of the plasma solver of the code, B2.5, is based on the assumption of perfectly field-aligned grids, while in practice grids are often strongly distorted to match divertor target shapes. Neglecting these grid distortion leads to qualitatively and quantitatively incorrect results for fluid neutral simulations, and may affect results in cold (detached) divertors even when using kinetic neutral simulations. In this contribution, we present the first results of a newly implemented 9-point stencil in B2.5 to properly handle misaligned grids. The new scheme is then applied to fluid neutral simulations of a well-diagnosed and previously modeled Alcator C-Mod discharge. Results are compared with the original 5-point scheme neglecting grid distortion effects, as well as with simulations including a full kinetic neutral model. We conclude that the 9-point stencil is essential to correctly model the transport of fluid neutrals on distorted grids, and to capture the effects of divertor closure on the fluid neutral behavior.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Simulations of divertor designs that spatially separate power and particle exhaust using mid-leg divertor particle pumping

Predictive design modeling of a Dissipation-Focused Divertor for future operation in DIII-D reveals that increasing the poloidal distance of the pump duct entrance from the target surface along the low-field side divertor baffle increases neutral compression and modifies the spatial distribution of power dissipation. With a divertor pump located mid-leg between the target and the X-point, SOLPS-ITER boundary plasma simulations without drifts predict the formation of a dense neutral cloud near the target with > 30x higher neutral compression in detachment, a more stable detachment front located further from the target, and ~25% lower outer midplane separatrix density required for detachment onset, compared to a pump located in the scrape-off layer at the target surface. Up to 19 MW of power flowing into the divertors is modeled using the following two numerical implementations for particle pumping: a specified fraction of particles incident on variable wall sections of the plasma grid is removed from the computational domain (so-called albedo pumping), and a pump duct is modeled which includes dynamics of kinetic neutrals in the duct. The simulations show that the detachment front is located between the divertor target and the X-point and is relatively stable near the pump entrance, without a strong dependence on gas puff rate or injected power. The mid-leg pump design spatially separates the two primary functions of a divertor (power handling and particle exhaust), with the majority of power dissipation occurring near the target plate and particle exhaust taking place further upstream. The benefit of enhanced dissipation using mid-leg pumping comes at the cost of a higher outer midplane separatrix density for a given amount of particle injection.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Simulation of divertor heat flux width on EAST by BOUT++ transport code

The BOUT++ edge plasma transport code is applied to study the effects of neutral recycling, drifts and heating scheme on edge plasma profiles and the divertor heat flux width of two discharges of the experimental advanced superconducting tokamak (EAST) steady-state H-mode plasmas heated by low hybrid wave (LHW) and neutral beam (NB), respectively. Neutral recycling seems to have played an important role in the plasma density profile. The edge plasma density drops dramatically for the case w/o neutral recycling, while it can be sustained for the case w/ neutral recycling. Drifts are found to have significant influences on edge plasma profiles. Both the amplitude and width of the divertor heat flux are found to have increased a lot due to drifts. The simulated heat flux width w/ drifts for the two discharges shows reasonable agreement with the experiments. However, the width from the simulation and experiment for the LHW heated discharge is much larger than that of the NB heated discharge. Comparison with Goldston's drift-based model and more detailed analysis on the heat flux contributions from drifts versus turbulence show that drifts are the dominant factor in edge plasma transport for both LHW and NB heated discharges, while turbulence may have played a more important role in determining the heat flux width in LHW heated discharges than that in NB heated discharges. This may account for the larger heat flux width in the LHW heated discharge. The magnetic topology and the equilibrium change by the LHW power may also be a potential reason for the larger heat flux width in the LHW heated discharges, which still needs more evidence and studies to support it. Finally, additional SOLPS simulation w/o drifts for the two discharges show reasonable agreement with the counterpart from the BOUT++ simulation, suggesting the two are both suitable codes for EAST edge plasma simulation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Investigation of the role of hydrogen molecules in 1D simulation of divertor detachment

The role of neutral and charged hydrogenic molecules in detached regimes of tokamak plasmas is investigated using a simplified 1D numerical model. Using MAST Upgrade like conditions, simulations are implemented to study the rollover of target flux Γ in upstream density scan. It is found that if H 2 and H 2 + are considered in simulations a lower target temperature and a larger upstream density will be required to trigger divertor detachment under the same input power and particle flux, and the critical detachment threshold (the critical ratio of upstream static pressure to the power entering the recycling region) is found to be $^{ρ_{up}}_{ρ_{recl}}$ ~ 8.1 NMW -1 at rollover. Molecule–plasma interactions are found to be as crucial as atom–plasma interactions during divertor detachment, both of which account for the majority of plasma momentum loss in the cases studied here. Further analysis of the momentum loss decomposition shows molecule-plasma elastic collisions dominate molecule-plasma interactions, while molecular charge exchange cannot effectively reduce plasma momentum. In terms of H alpha emission, a strong rise of H alpha signal is found to be due to molecular excitation channels when the upstream density further increases after rollover.

SD1D↗
DOE OSTI2026

Simulation of Divertor Performance in ST40 Under Dynamic Double-Null Plasmas

A power fraction model was implemented for the simultaneous prediction of 3-D surface temperature evolution at all four divertor targets in near-double-null (DN) tokamak configurations, which is especially important for compact high-field devices that may not have the ability to dissipate large amounts of power on the high-field side. Evaluating the power-sharing between the four divertor strike points in a disconnected DN configuration is important for understanding the overall power balance, as well as for optimizing the power exhaust performance and prolonging the survivability of the plasma facing components (PFCs). This power-sharing is typically evaluated in terms of the separation between the primary and secondary separatrices at the outboard midplane, $\textit {dR}_{\text {sep}}$. The Heat flux Engineering Analysis Toolkit (HEAT) is coupled with Brunner’s power fraction model to simulate the deposited heat flux and resultant temperature change on 3-D divertor targets in a dynamic DN (DDN) pulse operation in ST40, a high-field spherical tokamak. The simulation results showed that with DDN operation, the operation time has significantly increased compared with single-null geometry configurations.

ST40↗
DOE OSTI2025

Active Divertor Heat Flux Control using Impurity Powder Dropper

Divertor plasma-facing components (PFCs) in a tokamak are typically designed to withstand average steady-state heat loads of about 5–10 MW/m 2 , a limit that applies to both solid and liquid lithium (LL) PFCs. Exceeding these design values can result in surface damage to tungsten PFCs or excessive lithium (Li) evaporation in liquid lithium divertor (LLD) PFCs. Since exceeding the divertor heat load limits has serious consequences, it is therefore prudent to develop a tool to reduce the divertor heat load and bring the heat load to within the design limit without affecting the plasma performance. Active low Z impurity injection such as Li has been suggested as a potential solution to mitigate excess heat flux as suggested previously, given that non-coronal radiation can be quite large ~ 20–30 MJ per mole of injected Li. Li is considered desirable for reducing the edge neutral recycling helping to improve plasma energy confinement. In this paper, we model the Impurity Power Dropper (IPD) to investigate its potential of divertor heat flux control. The IPD is typically located at the top of the tokamak device and uses a vertical drift tube of a few meters. In the 2 m drift tube case, the IPD powder is accelerated to ~ 6 m/sec before reaching the plasma with the upper divertor configuration, matching the condition for the in-board side pellet injection case. By modeling the IPD geometry we determined the IPD powder deposition profile, and thus the non-coronal radiation and ionization profiles in time as well. From the enhanced radiation power loss, it is therefore possible to reduce the divertor heat load using the divertor simulation code. In conclusion, the IPD divertor heat flux control can be tested in the facilities with IPD including ST-40, DIII-D, EAST, WEST and NSTX-U.

Active lithium injection↗
DOE OSTI2024

Machine learning aided line intensity ratio method for helium–hydrogen mixed recombining plasmas

The helium line intensity ratio (LIR) with the help of a collisional radiative (CR) model has long been used to measure the electron density, n e , and temperature, T e , and its potential and limitations for fusion applications have been discussed. However, it has been reported that the CR model approach leads to deviations in helium–hydrogen mixed plasmas and/or recombining plasmas. In this study, a machine learning (ML) aided LIR method is used to measure n e and T e from spectroscopic data of helium–hydrogen mixed recombining plasmas in the divertor simulator Magnum-PSI. To analyze mixed plasmas, which have more complex spectral shapes, the spectroscopy data were used directly for training instead of separating the intensities of each line. Finally, it is shown that the ML approach can provide a robust and simpler analysis method to deduce n e and T e from the visible emissions in helium–hydrogen mixed plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Investigation of divertor detachment induced through neon seeding and density ramp on HL-3

A new self-consistent 1D scrape-off layer model has been recently developed in BOUT++ framework, named SD1D, which includes equations for various particle species (e.g. main plasma, neutrals and impurities) and couples open databases like ADAS and AMJUEL. It is able to quickly and effectively simulate divertor detachment experiments. In this work, a typical detachment experiment (shot #6270) on HL-3 with neon seeding is simulated using the SD1D code. It is found that the target electron temperature and the target ion saturation current in the simulations are consistent with experimental results measured by Langmuir probes on the target plate. The variation of D α radiation intensity in the divertor is qualitatively similar to the measured D α signal. Following the experimental validations, different upstream densities are set in the simulations to study the impurity distribution under different plasma density conditions. It is found that increasing upstream density can be helpful for the control of the neon radiation front (closer to the target). In this work we also compare two detachment regimes in simulations. Based on the same initial experimental parameters (shot #6270) on HL-3, a scan of upstream density and a scan of neon seeding rate are carried out respectively. It is found that the role of atomic and molecular processes is different in the two detachment regimes. The current density roll-over is ascribed to a drop in the divertor ion source, and the variation of D α radiation intensity via different excitation channels is associated with the relevant collisional reaction sources.

BOUT++↗
DOE OSTI2022

Kinetic simulations of collision-less plasmas in open magnetic geometries

Laboratory plasmas in open magnetic geometries can be found in many different applications such as (a) scrape-of-layer (SOL) and divertor regions in toroidal confinement fusion devices, (b) linear divertor simulators, (c) plasma-based thrusters and (d) magnetic mirrors etc. A common feature of these plasma systems is the need to resolve, in addition to velocity space, at least one physical dimension (e.g. along flux lines) to capture the relevant physics. In general, this requires a kinetic treatment. Fully kinetic particle-in-cell (PIC) simulations can be applied but at the expense of large computational effort. A common way to resolve this is to use a hybrid approach: kinetic ions and fluid electrons. In the present work, the development of a hybrid PIC computational tool suitable for open magnetic geometries is described which includes (a) the effect of non-uniform magnetic fields, (b) finite fully-absorbing boundaries for the particles and (c) volumetric particle sources. Analytical expressions for the momentum transport in the paraxial limit are presented with their underlying assumptions and are used to validate the results from the PIC simulations. A general method is described to construct discrete particle distribution functions in a state of mirror-equilibrium. This method is used to obtain the initial state for the PIC simulation. Collisionless simulations in a mirror geometry are performed. The results show that the effect of magnetic compression is correctly described and momentum is conserved. The self-consistent electric field is calculated and is shown to modify the ion velocity distribution function in a manner consistent with analytic theory. Based on this analysis, the ion distribution function is understood in terms of a loss-cone distribution and an isotropic Maxwell-Boltzmann distribution driven by a volumetric plasma source. Finally, the inclusion of a Monte Carlo based Fokker-Planck collision operator is discussed in the context of future work.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Toward Verification of RANS Simulations of the T-Tube Modular Divertor Using Large Eddy Simulations of Impinging Turbulent Plane Jets

Turbulent impinging jets have been proposed to cool high heat flux plasma-facing components such as the solid tungsten target plates of the divertor in long-pulse magnetic fusion energy reactors. In particular, the T-tube modular divertor, originally developed by the ARIES Team, consists of two concentric cylindrical tubes where helium flows through a slot in the inner tube, forming an approximately planar jet that impinges upon and cools the inner surface of the pressure boundary (namely, the outer tube) and the ~15-cm 2 plasma-facing W target. The objective of this work is to demonstrate that large eddy simulations (LESs) accurately simulate the thermal transport in canonical flows that comprise the cooling flow in the T-tube, as well as validate temperatures from LES with experimental measurements in a simplified T-tube geometry. Wall‑resolved LESs, validated by experimental data and verified by direct numerical simulations (DNSs), provide benchmark data for two canonical flows in the T‑tube, namely, planar impinging and wall jets, for Reynolds numbers Re B = 4 × 10 3 to 2 × 10 4 . Our LES results are within 4% to 12% root-mean-square error (RMSE) of surface Nusselt number distributions (Nu) from experiments and DNSs. The validated LES results are then used as the ground truth to evaluate four Reynolds‑averaged Navier-Stokes (RANS) turbulence closures, namely, the k‑ω SST, realizable k‑ε, GEKO, and γ‑SST models. The k‑ω SST model has the best overall performance in terms of heat transfer, giving surface Nu within 12% RMSE of the LES results for high‑ReB impinging jets and reduced overprediction in the wall‑jet region. The GEKO model with default constants has the next best performance, providing slightly better Nu predictions for low ReB impinging jets (versus k-ω SST) but worse overall performance over the full range of ReB studied here. The realizable k‑ε turbulence model significantly overestimates turbulence near the stagnation point, while the γ‑SST model suppresses near‑wall production, biasing the simulations toward simulating laminar surface heat transfer. Simulations of the simplified T‑tube show that LES and RANS simulations with the k‑ω SST model give nearly identical average heat transfer coefficients (HTCs) over the impingement surface. The realizable k‑ε model predicts significantly lower wall temperatures due to overestimation of HTC in the outlet flow.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Analysis of Design Alternatives of Actively Cooled RF Window for MPEX

The Materials Plasma Exposure eXperiment (MPEX) has been designed as a linear plasma divertor simulator in order to address plasma material interaction (PMI) science for next-generation fusion devices. It will have the capability to test neutron irradiated samples with plasma fluxes of greater than 10 24 m -2 s -1 . It is expected to operate steady state for up to 10 6 s to consider PMI affects through reactor end of life. The conceptual design of MPEX was completed in 2019, with preliminary design having begun in 2020. The plasma source for MPEX is a helicon antenna, where the energized helical antenna sits outside of the vacuum in order to minimize impurities in the plasma. It is expected to receive up to 200 kW of continuous power, and so the antenna and the window must be actively cooled. The water-cooled copper antenna has been operated at full power on the Proto-MPEX device (which is a test facility to demonstrate the plasma source and heating systems). The water-cooled window, however, is a novel component that must meet numerous competing requirements. It requires a low dielectric loss to allow the Radio Frequency (RF) power to create the plasma within the vacuum boundary. It must be structurally robust to handle the significant heat flux from the plasma and any heat from dielectric coupling. It must be compatible with the coolant (preferably water). It requires a vacuum seal that minimizes impurities into the plasma and does not compromise the structural integrity of the window. Two window designs have been tested. Results from these tests, where temperatures are measured and heat fluxes inferred from infrared camera data, have been correlated with thermal-structural simulations. When these simulations are extrapolated to the full power steady-state heat fluxes that are expected in MPEX, the designs do not appear to have the necessary structural robustness. This study explores design alternatives for the MPEX helicon antenna window, presents analysis results for several of the alternatives, and shows a viable solution that satisfies the requirements for MPEX operation.

Tipton Jr, Joseph↗
DOE OSTI2021

Characterizing the plasma-induced thermal loads on a 200 kW light-ion helicon plasma source via infra-red thermography

The light-ion helicon plasma source of the Proto-MPEX linear plasma device has been recently upgraded to enable pulsed (0.5–1 s) operation up to 200 kW. The main objective of this work is to report on the plasma-induced surface heat fluxes incident on the helicon window during high power operation (60–150 kW net power) for the purpose of the design of the upcoming material plasma exposure eXperiment (MPEX). The IR imaging system and associated physics models for the extraction of surface heat fluxes are presented. Furthermore, experimental results demonstrate that the control of the plasma strike point via magnetic flux mapping and the use of dedicated limiters is effective at reducing the heat loads on the dielectric window. Moreover, it is found that the flux mapping must create a gap between the plasma and the dielectric window of at least the plasma radial decay length. Extrapolated to 200 kW net RF power, this mode of operation can reduce the power lost to the dielectric window by 33%. The results presented have direct application to the design of high-powered helicon plasma sources that operate in a steady state. Examples include linear divertor simulators such as MPEX, electric thrusters, negative ion sources for NBI and linear plasma–material interaction test stands.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Conceptual Design and Analysis of In-Vessel Components for the Materials Plasma Exposure eXperiment (MPEX)

The materials plasma exposure experiment (MPEX) is a linear plasma divertor simulator currently undergoing conceptual design. The facility will expose material samples to steady-state plasma fluxes to examine plasma–material interactions (PMIs) that are expected in the next generation of fusion devices. The plasmas will be generated by a helicon source, with electron and ion heating sources of up to 800 kW possible. The peak heat fluxes of the target are expected to be up to 10 MW/m 2 . The facility will be capable of handling low-activation neutron-irradiated samples in order to examine the multivariate effects of neutron damage and plasma fluence. Neutron-irradiated samples are planned to be roughly of 10-mm diameter; however, plasma-facing components up to 60×600 mm can be accommodated. The steady-state nature of the device will require the magnetic confinement of the plasma to be achieved with superconducting magnets, with a maximum on-axis field of 2.5 T. In addition, since MPEX will be a steady-state device, in-vessel components need to be water cooled. The primary in-vessel components will be the target, the dump plate, the limiter, the skimmers, and the microwave absorber. The conceptual design of these components is presented here, including analyses that confirm that the designs are adequate to meet the requirements of MPEX operation.

Lumsdaine, Arnold↗