Search NASA⌕ Search

SEARCH · Search NASA

Results for “docking”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Magnetic docking aid for orbiter to ISS docking

The present docking system for the Orbiter uses mechanical capture latches that are actuated by contact forces. The forces are generated when the two approaching masses collide at the docking mechanism. There is always a trade-off between having high enough momentum to effect capture and low enough momentum to avoid structural overload or unacceptable angular displacements. The use of the present docking system includes a contact thrusting maneuver that causes high docking loads to be included into Space Station. A magnetic docking aid has been developed to reduce the load s during docking. The magnetic docking aid is comprised of two extendible booms that are attached adjacent to the docking structure with electromagnets attached on the end of the boom. On the mating vehicle, two steel plates are attached. As the Orbiter approaches Space Station, the booms are extended, and the magnets attach to the actuated (without thrusting), by slowly driving the extendible booms to the stowed position, thus reacting the load into the booms. This results in a docking event that has lower loads induced into Space Station structure. This method also greatly simplifies the Station berthing tasks, since the Shuttle Remote Manipulation System (SRMS) arm need only place the element to be berthed on the magnets (no load required), rather than firing the Reaction Control System (RCS) jets to provide the required force for capture latch actuation. The Magnetic Docking Aid was development testing on a six degree-of-freedom (6 DOF) system at JSC.

Schneider, William C.↗
NASA NTRS2017

Ground Demonstration on the Autonomous Docking of Two 3U CubeSats Using a Novel Permanent-Magnet Docking Mechanism

Small spacecraft autonomous rendezvous and docking is an essential technology for future space structure assembly missions. A novel magnetic capture and latching mechanism is analyzed that allows for docking of two CubeSats without precise sensors and actuators. The proposed magnetic docking hardware not only provides the means to latch the CubeSats but it also significantly increases the likelihood of successful docking in the presence of relative attitude and position errors. The simplicity of the design allows it to be implemented on many CubeSat rendezvous missions. A CubeSat 3-DOF ground demonstration effort is on-going at NASA Langley Research Center that enables hardware-in-the loop testing of the autonomous approach and docking of a follower CubeSat to an identical leader CubeSat. The test setup consists of a 3 meter by 4 meter granite table and two nearly frictionless air bearing systems that support the two CubeSats. Four cold-gas on-off thrusters are used to translate the follower towards the leader, while a single reaction wheel is used to control the attitude of each CubeSat. An innovative modified pseudo inverse control allocation scheme was developed to address interactions between control effectors. The docking procedure requires relatively high actuator precision, a novel minimal impulse bit mitigation algorithm was developed to minimize the undesirable deadzone effects of the thrusters. Simulation of the ground demonstration shows that the Guidance, Navigation, and Control system along with the docking subsystem leads to successful docking under 3-sigma dispersions for all key system parameters. Extensive simulation and ground testing will provide sufficient confidence that the proposed docking mechanism along with the choosen suite of sensors and actuators will perform successful docking in the space environment.

Pei, Jing↗
NASA NTRS2011

Overview of the NASA Docking System (NDS) and the International Docking System Standard (IDSS)

The NASA/JSC Engineering Directorate has been developing the technology for a Low Impact Docking System (LIDS) for many years. LIDS had been chosen to be the Constellation Program baseline. In February 2009, the International Space Station (ISS) Multilateral control Board (MCB) began an initiative to develop an International Docking System Standard (IDSS) to facilitate greater international cooperation in space and enable emergency crew rescue missions. Discussions as to whether the LIDS could be made compatible with the IDSS were under way. With the cancellation of the Constellation Program, NASA made a policy decision to convert both of the docking ports on the United States On-orbit Segment (USOS) to IDSS ports and NASA moved the LIDS project under the ISS Program. LIDS was redesigned to become the NASA implementation of the emerging IDSS, and its name was changed to the NASA Docking System (NDS). The NDS design will be certified as a gblack box h which can be integrated onto vehicles planning to dock to the ISS IDSS ports. This presentation will discuss the evolution of the IDSS from both the LIDS and the Androgynous Peripheral Assembly System (APAS) and outline the interface requirements which are given in the IDSS Interface Definition Document (IDD). It also will give an overview of the current NDS design, and touch on ISS plans for converting its docking ports to be IDSS compliant.

Parma, George F.↗
NASA NTRS2018

NASA Docking System Block 1: NASA's New Direct Electric Docking System Supporting ISS and Future Human Space Exploration

The NASA Docking System (NDS) Block 1 is a key component of NASA's vision for space exploration. It is designed to provide capability for visiting vehicles to dock to the International Space Station's recently-installed International Docking Adapter ports. It is the first docking system to be developed by NASA since the Apollo-Soyuz Test Project of the 1970's. The NDS Block 1 includes provisions for capture, structural attachment, power/data transfer, and undocking. It uses a direct-drive electromechanical Stewart Platform capture system architecture, along with an innovative automated control scheme, to achieve an unprecedented level of performance and simplicity. Its design implements the new International Docking System Standard, which will be a key enabler of diverse and flexible exploration missions in future iterations. NDS qualification was completed in 2017 to support a planned first flight in 2018 on the Boeing CST-100 Starliner.

NASA Docking System↗
NASA NTRS2015

Design and Preliminary Testing of the International Docking Adapter's Peripheral Docking Target

The International Docking Adapter's Peripheral Docking Target (PDT) was designed to allow a docking spacecraft to judge its alignment relative to the docking system. The PDT was designed to be compatible with relative sensors using visible cameras, thermal imagers, or Light Detection and Ranging (LIDAR) technologies. The conceptual design team tested prototype designs and materials to determine the contrast requirements for the features. This paper will discuss the design of the PDT, the methodology and results of the tests, and the conclusions pertaining to PDT design that were drawn from testing.

Foster, Christopher W.↗
NASA NTRS1974

Analyses of the dynamic docking test system for advanced mission docking system test programs

Results are given of analytical studies performed in support of the design, implementation, checkout and use of NASA's dynamic docking test system (DDTS). Included are analyses of simulator components, a list of detailed operational test procedures, a summary of simulator performance, and an analysis and comparison of docking dynamics and loads obtained by test and analysis.

Gates, R. M.↗
NASA NTRS1991

Standard remote manipulator system docking target augmentation for automated docking

A docking target is provided for use in automated docking of a first vehicle on which the target is located. The target comprises a pair of laterally extending arm portions lying in substantially the same plane and a central post extending outwardly from the plane of the arm portions. At least three reflectors are located on the target. Two of the reflectors are located at the outboard ends of the arms portions and another reflector is located at the end of the central post. In an important embodiment, the reflectors comprise individual pieces of retroreflective tape. The reflectors, when viewed from the front of the target, are aligned along the longitudinal center line of the target, and can take a number of different shapes including circular or square.

Dabney, Richard W.↗
NASA NTRS1974

Dynamic Docking Test System (DDTS) active table computer program NASA Advanced Docking System (NADS)

A computer program was developed to describe the three-dimensional motion of the Dynamic Docking Test System active table. The input consists of inertia and geometry data, actuator structural data, forcing function data, hydraulics data, servo electronics data, and integration control data. The output consists of table responses, actuator bending responses, and actuator responses.

Gates, R. M.↗
NASA NTRS2016

International Docking Standard (IDSS) Interface Definition Document (IDD) : Revision - E

This International Docking System Standard (IDSS) Interface Definition Document (IDD) is the result of a collaboration by the International Space Station membership to establish a standard docking interface to enable on-orbit crew rescue operations and joint collaborative endeavors utilizing different spacecraft. This IDSS IDD details the physical geometric mating interface and design loads requirements. The physical geometric interface requirements must be strictly followed to ensure physical spacecraft mating compatibility. This includes both defined components and areas that are void of components. The IDD also identifies common design parameters as identified in section 3.0, e.g., docking initial conditions and vehicle mass properties. This information represents a recommended set of design values enveloping a broad set of design reference missions and conditions, which if accommodated in the docking system design, increases the probability of successful docking between different spacecraft. This IDD does not address operational procedures or off-nominal situations, nor does it dictate implementation or design features behind the mating interface. It is the responsibility of the spacecraft developer to perform all hardware verification and validation, and to perform final docking analyses to ensure the needed docking performance and to develop the final certification loads for their application. While there are many other critical requirements needed in the development of a docking system such as fault tolerance, reliability, and environments (e.g. vibration, etc.), it is not the intent of the IDSS IDD to mandate all of these requirements; these requirements must be addressed as part of the specific developer's unique program, spacecraft and mission needs. This approach allows designers the flexibility to design and build docking mechanisms to their unique program needs and requirements. The purpose of the IDSS IDD is to provide basic common design parameters to allow developers to independently design compatible docking systems. The IDSS is intended for uses ranging from crewed to autonomous space vehicles, and from Low Earth Orbit (LEO) to deep-space exploration missions.The purpose of the IDSS IDD is to provide basic common design parameters to allow developers to independently design compatible docking systems. The IDSS is intended for uses ranging from crewed to autonomous space vehicles, and from Low Earth Orbit (LEO) to deep-space exploration missions. The purpose of the IDSS IDD is to provide basic common design parameters to allow developers to independently design compatible docking systems. The IDSS is intended for uses ranging from crewed to autonomous space vehicles, and from Low Earth Orbit (LEO) to deep-space exploration missions.

docking↗
NASA NTRS2007

Magnet-Based System for Docking of Miniature Spacecraft

A prototype system for docking a miniature spacecraft with a larger spacecraft has been developed by engineers at the Johnson Space Center. Engineers working on Mini AERCam, a free-flying robotic camera, needed to find a way to successfully dock and undock their miniature spacecraft to refuel the propulsion and recharge the batteries. The subsystems developed (see figure) include (1) a docking port, designed for the larger spacecraft, which contains an electromagnet, a ball lock mechanism, and a service probe; and (2) a docking cluster, designed for the smaller spacecraft, which contains either a permanent magnet or an electromagnet. A typical docking operation begins with the docking spacecraft maneuvering into position near the docking port on the parent vehicle. The electromagnet( s) are then turned on, and, if necessary, the docking spacecraft is then maneuvered within the capture envelope of the docking port. The capture envelope for this system is approximated by a 5-in. (12.7-cm) cube centered on the front of the docking-port electromagnet and within an angular misalignment of <30 . Thereafter, the magnetic forces draw the smaller spacecraft toward the larger one and this brings the spacecraft into approximate alignment prior to contact. Mechanical alignment guides provide the final rotational alignment into one of 12 positions. Once the docking vehicle has been captured magnetically in the docking port, the ball-lock mechanism is activated, which locks the two spacecraft together. At this point the electromagnet( s) are turned off, and the service probe extended if recharge and refueling are to be performed. Additionally, during undocking, the polarity of one electromagnet can be reversed to provide a gentle push to separate the two spacecraft. This system is currently being incorporated into the design of Mini AERCam vehicle.

Howard, Nathan↗
NASA NTRS2012

A Comparison of Candidate Seal Designs for Future Docking Systems

NASA is developing a new docking system to support future space exploration missions to low Earth orbit, the Moon, and other destinations. A key component of this system is the seal at the main docking interface which inhibits the loss of cabin air once docking is complete. Depending on the mission, the seal must be able to dock in either a seal-on-flange or seal-on-seal configuration. Seal-on-flange mating would occur when a docking system equipped with a seal docks to a system with a flat metal flange. This would occur when a vehicle docks to a node on the International Space Station. Seal-on-seal mating would occur when two docking systems equipped with seals dock to each other. Two types of seal designs were identified for this application: Gask-O-seals and multi-piece seals. Both types of seals had a pair of seal bulbs to satisfy the redundancy requirement. A series of performance assessments and comparisons were made between the candidate seal designs indicating that they meet the requirements for leak rate and compression and adhesion loads under a range of operating conditions. Other design factors such as part count, integration into the docking system tunnel, seal-on-seal mating, and cost were also considered leading to the selection of the multi-piece seal design for the new docking system. The results of this study can be used by designers of future docking systems and other habitable volumes to select the seal design best-suited for their particular application.

Dunlap, Patrick, H., Jr.↗
NASA NTRS1974

Six degree of freedom FORTRAN program, ASTP docking dynamics, users guide

The digital program ASTP Docking Dynamics as outlined is intended to aid the engineer using the program to determine the docking system loads and attendant vehicular motion resulting from docking two vehicles that have an androgynous, six-hydraulic-attenuator, guide ring, docking interface similar to that designed for the Apollo/Soyuz Test Project (ASTP). This program is set up to analyze two different vehicle combinations: the Apollo CSM docking to Soyuz and the shuttle orbiter docking to another orbiter. The subroutine modifies the vehicle control systems to describe one or the other vehicle combinations; the rest of the vehicle characteristics are changed by input data. To date, the program has been used to predict and correlate ASTP docking loads and performance with docking test program results from dynamic testing. The program modified for use on IBM 360 computers. Parts of the original docking system equations in the areas of hydraulic damping and capture latches are modified to better describe the detail design of the ASTP docking system.

Mount, G. O., Jr.↗
NASA NTRS2011

Orion Handling Qualities During ISS Rendezvous and Docking

The Orion spacecraft was designed to rendezvous with multiple vehicles in low earth orbit (LEO) and beyond. To perform the required rendezvous and docking task, Orion must provide enough control authority to perform coarse translational maneuvers while maintaining precision to perform the delicate docking corrections. While Orion has autonomous docking capabilities, it is expected that final approach and docking operations with the International Space Station (ISS) will initially be performed in a manual mode. A series of evaluations was conducted by NASA and Lockheed Martin at the Johnson Space Center to determine the handling qualities (HQ) of the Orion spacecraft during different docking and rendezvous conditions using the Cooper-Harper scale. This paper will address the specifics of the handling qualities methodology, vehicle configuration, scenarios flown, data collection tools, and subject ratings and comments. The initial Orion HQ assessment examined Orion docking to the ISS. This scenario demonstrates the Translational Hand Controller (THC) handling qualities of Orion. During this initial assessment, two different scenarios were evaluated. The first was a nominal docking approach to a stable ISS, with Orion initializing with relative position dispersions and a closing rate of approximately 0.1 ft/sec. The second docking scenario was identical to the first, except the attitude motion of the ISS was modeled to simulate a stress case ( 1 degree deadband per axis and 0.01 deg/sec rate deadband per axis). For both scenarios, subjects started each run on final approach at a docking port-to-port range of 20 ft. Subjects used the THC in pulse mode with cues from the docking camera image, window views, and range and range rate data displayed on the Orion display units. As in the actual design, the attitude of the Orion vehicle was held by the automated flight control system at 0.5 degree deadband per axis. Several error sources were modeled including Reaction Control System (RCS) jet angular and position misalignment, RCS thrust magnitude uncertainty, RCS jet force direction uncertainty due to self plume impingement, and Orion center of mass uncertainty.

Hart, Jeremy J.↗
NASA NTRSDate not supplied

A Multi-Gravity Docking and Utilities Transfer System for a Common Habitat Architecture

The Common Habitat architecture, a study architecture based on a large habitat derived from the SLS Core Stage Liquid Oxygen tank and designed to operate in microgravity, lunar surface, and Mars surface environments, requires a pressurized docking and berthing system that also works in all three domains. Prior flown docking systems have only been designed for microgravity, but a prototype suit port-derived docking system was developed under the Constellation program for the lunar surface. This system employed an active-active mating adapter approach consisting of a simplistic passive docking system on all spacecraft and a pressurized mating adapter with active systems on each end to form the docking connection. Derived from this approach, the Common Habitat architecture will use a multi-gravity active-active mating adapter (MGAAMA) to perform this function on the Moon, Mars, and in microgravity, connecting the various pressurized elements needed for surface base camps or deep space habitation. Design aspects and open trades of the MGAAMA system will be described. In addition to forming a structural connection and enabling the transfer of crew and equipment, the MGAAMA must also transfer utilities in the form of gases, fluids, power, and data. The MGAAMA is also designed with a degree of articulation in order to accommodate significant angular misalignment. Due to the environmental conditions the MGAAMA will experience, dust and thermal protection systems are discussed. Because the MGAAMA involves docking to spacecraft with different docking systems of different sizes, the MGAAMA is a family of docking systems with interfaces compatible with current and legacy spacecraft docking systems.

Docking↗
NASA NTRS1972

Docking system of androgynous and peripheral type

Soviet and American space engineers have proceeded with creating compatible means for closing and docking spacecraft. It was decided to make a new advanced docking system of a peripheral and androgynous type. Because of a more complex design of the new-type docking mechanism, a number of technical problems arose. To a great extent, the solution of these problems depends on a chosen concept of the docking mechanism. The report deals with the docking system concept accepted by the Soviet engineers as the basis for further development. The description and structural arrangement of the docking system as a whole, its basic assemblies, and a kinematic scheme of the docking mechanism using a system of differentials are given. It should be noted that the experience that was gained from the development of previous docking systems was used to create a new type of docking system. The main problems to be solved in the course of designing and developing the advanced system are noted.

Syromyatnikov, V. S.↗
NASA NTRS1988

Docking system for spacecraft

A mechanism is disclosed for the docking of a spacecraft to a space station where a connection for transfer of personnel and equipment is desired. The invention comprises an active docking structure on a spacecraft and a passive docking structure on the station. The passive structure includes a docking ring mounted on a tunnel structure fixed to the space station. The active structure includes a docking ring carried by an actuator-attenuator devices, each attached at one end to the ring and at its other end in the spacecraft payload bay. The devices respond to command signals for moving the docking ring between a stowed position in the spacecraft to a deployed position suitable for engagement with the docking ring. The devices comprise means responsive to signals of sensed loadings to absorb impact energy and retraction means for drawing the coupled spacecraft and station into final docked configuration and moving the tunnel structure to a berthed position in the spacecraft. Latches couple the spacecraft and space station upon contact of the docking rings and latches establish a structural tie between the spacecraft when retracted.

Kahn, Jon B.↗