Search NASA⌕ Search

SEARCH · Search NASA

Results for “drag estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Cauchy Drag Estimation For Low Earth Orbiters

Recent work on minimum variances estimators based on Cauchy distributions appear relevant to orbital drag estimation. Samples form Cauchy distributions which are part of a class of heavy-tailed distributions, are characterized by long stretches of fairly small variation, punctuated by large variations that are many times larger than could be expected from a Gaussian. Such behavior can occur when solar storms perturb the atmosphere. In this context, the present work describes an embedding of the scalar Idan-Speyer Cauchy Estimator to estimate density corrections, within an Extended Kalman Filter that estimates the state of a low Earth orbiter. In contrast to the baseline Kalman approach, the larger formal errors of the present approach fully and conservatively bound the predictive error distribution, even in the face of unanticipated density disturbances of hundreds of percent.

Low Earth↗
NASA NTRS1961

External-Drag Estimation for Slender Conical Ducted Bodies at High Mach Numbers and Zero Angle of Attack

A method of estimation of the external drag of slender conical ducted bodies at high Mach numbers and zero angle of attack is presented. Charts of the pressure drag computed with the use of characteristics theory and charts of the skin-friction drag evaluated from boundary-layer theory are presented. In addition, some sample plots of the variation of drag characteristics with Mach number and with geometric parameters are presented.

Valentine, E. Floyd↗
NASA NTRS1980

Comparisons of subsonic drag estimates derived from Pioneer Venus probes flight data with wind-tunnel results

Subsonic drag coefficients have been obtained from flight data for the Pioneer Venus multiprobes. The technique used to extract the information from the data consisted of utilizing in situ pressure and temperature measurements. Analysis of the major model parameter error sources indicates overall error levels of five percent or less in the flight values of the drag coefficient. Comparisons of the flight coefficients with preflight wind-tunnel test data showed generally good agreement except for the Sounder descent probe configuration. To preclude atmospheric phenomena as a possible explanation of this difference, additional wind-tunnel tests were performed on the Sounder descent probe. Special attempts were made to duplicate the probe geometry for tests in a high Reynolds number environment in order to achieve as realistic model and flight conditions as practical. Preliminary results from this testing in the NASA LaRC Low Turbulence Pressure Tunnel produced a drag coefficient of 0.68 at 0 deg angle of attack which is within the expected accuracy limits of the flight derived drag coefficient value of 0.72 + or - 0.04, thus eliminating atmospheric phenomena as the explanation for the initial difference.

Blanchard, R. C.↗
NASA NTRS1984

Method to estimate drag coefficient at the air/ice interface over drifting open pack ice from remotely sensed data

A knowledge in near real time, of the surface drag coefficient for drifting pack ice is vital for predicting its motions. And since this is not routinely available from measurements it must be replaced by estimates. Hence, a method for estimating this variable, as well as the drag coefficient at the water/ice interface and the ice thickness, for drifting open pack ice was developed. These estimates were derived from three-day sequences of LANDSAT-1 MSS images and surface weather charts and from the observed minima and maxima of these variables. The method was tested with four data sets in the southeastern Beaufort sea. Acceptable results were obtained for three data sets. Routine application of the method depends on the availability of data from an all-weather air or spaceborne remote sensing system, producing images with high geometric fidelity and high resolution.

Feldman, U.↗
NASA NTRS2019

Estimating Drag and Heating Coefficients for Hollow Reentry Objects in Transitional Flow Using DSMC

In NASA’s Object Reentry Survival Analysis Tool (ORSAT), aerodynamic drag and aerothermal heating coefficients are computed for each of the free-molecular, continuum, and transitional flow regimes using analytical and semi-analytical methods. These methods are typically limited to convex, blunt objects (such as spheres) and are applied to other objects such as boxes and cylinders using multiplicative “shape factors” to account for the different behavior. Previous literature has analyzed the aerodynamic and aerothermodynamic properties of flow around sharp-edged objects like boxes and cylinders in transitional flow, though only those objects with solid external boundaries. However, many reentry objects we have encountered in real spacecraft have been hollow (i.e., with the potential to allow flow through them). We present here preliminary results from analyses performed using the NASA Direct Simulation Monte Carlo (DSMC) Analysis Code (DAC) on hollow cylinders and boxes (with varying wall thickness-diameter ratio).

Marichalar, Jeremiah J.↗
NASA NTRS1980

Drag-free estimation feasibility study

A drag compensation system for solar probes and other spacecraft that require a drag-free capability is presented. Estimation techniques, derived from modern control theory, are proposed.

Schaechter, D. B.↗
NASA NTRS2003

Re-examination of Mars Pathfinder parachute drag coefficient estimate

The Mars Exploration Rover (MER) mission utilizes the Mars Pathfinder (MPF) parachute design. The MPF parachute drag coefficient is a driver for the MER entry, descent, and landing (EDL) design. As a result, a good estimate of the performance of the MPF parachute at Mars is required.

Mars Pathfinder parachute drag construction↗
NASA NTRS2009

Hybrid Wing Body Configuration System Studies

The objective of this study was to develop a hybrid wing body (HWB) sizing and analysis capability, apply that capability to estimate the fuel burn potential for an HWB concept, and identify associated technology requirements. An advanced tube with wings concept was also developed for comparison purposes. NASA s Flight Optimization System (FLOPS) conceptual aircraft sizing and synthesis software was modified to enable the sizing and analysis of HWB concepts. The noncircular pressurized centerbody of the HWB concept was modeled, and several options were created for defining the outboard wing sections. Weight and drag estimation routines were modified to accommodate the unique aspects of an HWB configuration. The resulting capability was then utilized to model a proprietary Boeing blended wing body (BWB) concept for comparison purposes. FLOPS predicted approximately a 15 percent greater drag, mainly caused by differences in compressibility drag estimation, and approximately a 5 percent greater takeoff gross weight, mainly caused by the additional fuel required, as compared with the Boeing data. Next, a 777-like reference vehicle was modeled in FLOPS and calibrated to published Boeing performance data; the same mission definition was used to size an HWB in FLOPS. Advanced airframe and propulsion technology assumptions were applied to the HWB to develop an estimate for potential fuel burn savings from such a concept. The same technology assumptions, where applicable, were then applied to an advanced tube-with-wings concept. The HWB concept had a 39 percent lower block fuel burn than the reference vehicle and a 12 percent lower block fuel burn than the advanced tube-with-wings configuration. However, this fuel burn advantage is partially derived from assuming the high-risk technology of embedded engines with boundary-layer-ingesting inlets. The HWB concept does have the potential for significantly reduced noise as a result of the shielding advantages that are inherent with an over-body engine installation.

Nickol, Craig L.↗
NASA NTRS1978

Inlet-engine matching for SCAR including application of a bicone variable geometry inlet

Airflow characteristics of variable cycle engines (VCE) designed for Mach 2.32 can have transonic airflow requirements as high as 1.6 times the cruise airflow. This is a formidable requirement for conventional, high performance, axisymmetric, translating centerbody mixed compression inlets. An alternate inlet is defined, where the second cone of a two cone center body collapses to the initial cone angle to provide a large off-design airflow capability, and incorporates modest centerbody translation to minimize spillage drag. Estimates of transonic spillage drag are competitive with those of conventional translating centerbody inlets. The inlet's cruise performance exhibits very low bleed requirements with good recovery and high angle of attack capability.

Wasserbauer, J. F.↗
NASA NTRS1978

Inlet-engine matching for SCAR including application of a bicone variable geometry inlet

Airflow characteristics of variable cycle engines (VCE) designed for Mach 2.32 can have transonic airflow requirements as high as 1.6 times the cruise airflow. This is a formidable requirement for conventional, high performance, axisymmetric, translating centerbody mixed compression inlets. An alternate inlet is defined where the second cone of a two cone centerbody collapses to the initial cone angle to provide a large off-design airflow capability, and incorporates modest centerbody translation to minimize spillage drag. Estimates of transonic spillage drag are competitive with those of conventional translating centerbody inlets. The inlet's cruise performance exhibits very low bleed requirements with good recovery and high angle of attack capability.

Wasserbauer, J. F.↗
NASA NTRS1993

Determination of balloon gas mass and revised estimates of drag and virtual mass coefficients

In support of the NASA Balloon Program, small-scale balloons were flown with varying lifting gas and total system mass. Instrument packages were developed to measure and record acceleration and temperature data during these tests. Top fitting and instrument payload accelerations were measured from launch to steady state ascent and through ballast drop transients. The development of the small lightweight self-powered Stowaway Special instrument packages is discussed along with mathematical models developed to determine gas mass, drag and virtual mass coefficients.

Robbins, E.↗
NASA NTRS1975

Learjet model 25 drag analysis

Procedures and data for estimating drag were used to calculate the drag characteristics of the Model 25 airplane. Based on cruise flight test data obtained on the Model 25, these methods generally predicted the total drag characteristics within current acceptable and reasonable engineering accuracy.

Ross, R.↗
NASA NTRS1977

A study of commuter airplane design optimization

Problems of commuter airplane configuration design were studied to affect a minimization of direct operating costs. Factors considered were the minimization of fuselage drag, methods of wing design, and the estimated drag of an airplane submerged in a propellor slipstream; all design criteria were studied under a set of fixed performance, mission, and stability constraints. Configuration design data were assembled for application by a computerized design methodology program similar to the NASA-Ames General Aviation Synthesis Program.

Roskam, J.↗
NASA NTRS2019

Interference Drag Associated with Engine Locations for Multidisciplinary Design Optimization

This research aims to quantify the interference drag for various engine locations on a traditional “tube and wing,” 150-passenger commercial aircraft flying at 35,000 ft and Mach 0.8. Engine locations are varied in the chord wise, span wise, and vertical directions near the wing, both under and above the wing, as well as along the fuselage. Euler simulations are performed with representative powered modern engines. The results are intended to supplement empirical drag estimates suitable for multidisciplinary design environments. Large interference drag increases, as compared to the isolated air frame and engine geometry, are found to occur when the engine is placed directly above or below the wing. Interference effects are significantly reduced, and in some instances result in benefits compared to the isolated bodies, when the engines are placed fore or aft of the wing. Interference drag increases are partially explained by flow channels leading to choked flow and shock interactions between bodies.

Blaesser, Nathaniel J.↗
NASA NTRS1966

Summary of External-Store Drag

The drag problems associated with the addition of external stores to airplanes are reviewed. Current analytic techniques for estimating drag penalties associated with the addition of stores in both subsonic and supersonic flight are discussed. In subsonic flight, the drag penalty caused by the addition of external stores is shown to be a function of the type of store installation. In supersonic flight, the drag is shown to be a function of the type of store installation and also of the location of the store installation with respect to the rest of the airplane components. Special store arrangements and attention to the design of the store itself can reduce the drag penalty of the store installation.

Shrout, B. L.↗
NASA NTRS2006

Atmospheric drag model for Cassini orbit determination during low altitude Titan flybys

On April 16, 2005, the Cassini spacecraft performed its lowest altitude flyby of Titan to date, the Titan-5 flyby, flying 1027 km above the surface of Titan. This document discusses the development of a Titan atmospheric drag model for the purpose of the orbit determination of Cassini. Results will be presented for the Titan A flyby, the Titan-5 flyby as well as the most recent low altitude Titan flyby, Titan-7. Different solutions will be compared against OD performance in terms of the flyby B-plane parameters, spacecraft thrusting activity and drag estimates. These low altitude Titan flybys were an excellent opportunity to observe the effect of Titan's atmospheric drag on the orbit determination solution and results show that the drag was successfully modeled to provide accurate flyby solutions.

orbit determination↗