Search NASA⌕ Search

SEARCH · Search NASA

Results for “drag modulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2020

Experimental Investigation of Drag Modulation Aerocapture: Drag-Skirt Separation in Hypersonic Free Flight

Free flight tests were conducted in carbon dioxide at Mach 12 of notional drag modulation aerocapture configurations for a small satellite mission to Venus. The configurations were based on research conducted at the Georgia Institute of Technology, University of Colorado Boulder, Jet Propulsion Laboratory, and Ames Research Center. The drag modulation aerocapture approach being studied involves an atmospheric entry vehicle that employs an attached drag device, a drag skirt, that is jettisoned at the appropriate time to allow the payload-portion of the vehicle to exit the atmosphere, slowed enough to be captured into orbit. A total of eight tests were performed. Reynolds numbers, based on the pre-separation base diameter, ranged from 0.82 x 106 to 2.96 x 106. The tests demonstrated the feasibility of a clean drag skirt separation at hypersonic speeds and, for the conditions of the tests, the stability of the central flight system body during and after separation from the drag skirt. Two drag skirt geometries were tested: an axisymmetric conical frustum, and a faceted frustum representative of a mechanically-deployable device. Drag skirts of various masses were tested to examine the effect of pre- and post-separation ballistic coefficient ratio on the separation dynamics. A new test capability for multi-body interactions in hypersonic free flight was developed for these tests, and is described.

aerocapture↗
NASA NTRS2018

Studies in Support of Venus Aerocapture Utilizing Drag Modulation

Aerocapture has been extensively studied and these studies have shown the benefit for planetary exploration missions. While the traditional approach to aerocapture with lifting configurations and lift-guided modulations have been assessed to be technologically feasible, aerocapture using purely drag modulation was proposed and studied by Prof. Braun and his students. These studies show that if one can assess the feasibility of aerocapture using drag modulation at Venus, and develop tall pole technologies needed at Venus, then this concept is much easier to execute at all other relevant destinations. Based on the above finding, partnered proposals were submitted by Adam Nelessen at JPL and Ethiraj Venkatapathy at Ames in collaboration with Prof. Braun at the University of Colorado, Boulder (UCB). Under this partnership, Ames Research Center (ARC) is working to address some of the key entry technology challenges associated with drag modulation aerocapture at Venus. Drag modulation aerocapture is a simple, scalable, and likely cost-effective way to enhance planetary science missions. The approach envisioned is to design a small spacecraft, that would most likely be a secondary payload, with a removable drag skirt. The vehicle would enter the atmosphere at Venus with a low ballistic coefficient, decelerate rapidly, drop the skirt resulting in a smaller vehicle with a higher ballistic coefficient which would skip out of the atmosphere and enter into a desired orbit. ARC's role in this collaboration is multifold. First of which is to perform design studies on various pre- and post-jettison geometries utilizing a 3-DOF trajectory code to determine the aerodynamics and aerothermodynamics of the vehicles and evaluate viable thermal protection material system designs. Once these design studies are complete, Ames will then perform higher fidelity CFD and TPS sizing to further design the vehicles. Second, the multi-body separation dynamics of the drag modulation event will be explored using both CFD simulations (CART3-D and US3D) as well as possible ballistic range testing. ARC's tools and expertise have been used to assess and advise on the selection of the separating configuration. In addition to the preliminary evaluation, ARC will provide tools and expertise to UCB team members to further assess aerodynamic interactions between the separating bodies and provide guidance as to the feasibility of stable transition.

Beck, Robin↗
NASA NTRSDate not supplied

Performance Analysis of Magnetohydrodynamic Drag Modulation for Actively Controlled Aerocapture at Neptune

Missions to the Ice Giants are a top priority for flagship missions this coming decade. However, a fully propulsive orbital insertion into these planets requires an immense amount of fuel, taking a significant portion of the spacecraft mass and restricting the scientific payload. To mitigate this, aerocapture has been heavily investigated. Although simulations have shown that aerodynamically controlled aerocapture can successfully insert into an orbit around both Ice Giants, the deep atmospheric pass required necessitates a complex, mass expensive, and sometimes prohibitive thermal protection system. Magnetohydrodynamic drag modulation serves as a potential alternative control method for aerocapture which could not only save propellant mass compared to fully propulsive orbital insertion, but also save thermal protection system mass compared to conventional aerocapture methods. Both aerodynamically controlled and magnetohydrodynamically controlled aerocapture methodologies were simulated in NASA Langley’s high-fidelity six degree-of-freedom flight dynamics code, the Program to Optimize Simulated Trajectories II. Each method was simulated to identical missions to Neptune using a numerical predictor-corrector algorithm to optimize the control towards the target orbit. The results concluded that magnetohydrodynamic drag modulation can successfully capture and performs on par with aerodynamic drag modulation while significantly reducing the heatflux and aeroshell complexity.

Danny N Nguyen↗
NASA NTRS2023

Computational Aerothermal Modeling and Simulation of Hypersonic, Low-density Flows for the ADEPT Drag Modulated Aerocapture Mission

NASA Ames Entry Systems and Technology Division has been leading development and testing of the Adaptable, Deployable, Entry and Placement Technology (ADEPT). A teaming partnership with JPL has been established to study and develop a compelling application of the ADEPT mechanically deployable hypersonic decelerator as part of the Venus Drag Modulated Aerocapture (VDMA) JPL R&TD effort. The primary work of this activity is to develop a design tool for the ADEPT drag skirt (e.g. a CFD-anchored CBAERO model) that enables rapid estimation of aerothermal environments for a range of candidate trajectories. This capability will enable rapid feasibility trades and design assessments for early stage mission concept evaluation for ADEPT Drag Modulated Aerocapture applications. Results of using TPSizer provided an ADEPT carbon fabric design thickness of the required number of fabric layers needed for predicted aerothermal environments and still have sufficient fabric remaining for overall vehicle integrity. This resulted in aerothermal design closure of the ADEPT drag skirt. In addition, the similar methodology for Venus DMA was used to assess a similar DMA operation at Earth as part of a possible Technology Demonstration Mission (TDM) for ADEPT DMA. This analysis showed that there is a close similarity of design approaches for an Earth DMA TDM that would be applicable to Venus DMA mission designs.

Drag Modulated Aerocapture↗
NASA NTRS1983

Optimization and closed loop guidance of drag modulated aeroassisted orbital transfer

An analysis of optimal and near optimal atmospheric flight trajectories for drag modulated aeroassisted orbital transfer is presented. An explicit and adaptive closed loop guidance approach for this mode of orbit transfer is also presented with performance near the optimal nominal trajectories. The orbital transfer of interest is for return from high earth orbit to low earth orbit. Most of what is discussed in this paper concerns the aeroassisted or atmospheric segment which lowers the apogee of the high earth orbit to the apogee of the low earth orbit. Minimization of the total impulsive delta-V at this low earth orbit apogee is the optimization criterion. Control about this impulse due to a number of potential error sources in atmospheric braking is the requirement imposed on closed loop guidance.

Kechichian, J. A.↗
NASA NTRS2019

A Neptune Orbiter Concept Using Drag Modulated Aerocaptue (DMA) and the Adaptable, Deployable Entry and Placement Technology (ADEPT)

Conceptual Neptune orbiter was designed for the purpose of assessing mission feasibilityBuilt off of the 2017 Pre-Decadal Study, but adapted for drag modulation aerocapture.Science payload includes: Narrow Angle camera, Doppler Imager, Magnetometer, Atmospheric Probe (w/ ASI, Nephelometer, Mass Spectrometer). Baseline concept of operations releases probe prior to orbit insertion, but investigations are ongoing to assess the feasibility of bringing the probe to orbit before release.

Wercinski, P.↗
NASA NTRS2016

Modeling the Exo-Brake and the Development of Strategies for De-Orbit Drag Modulation

The Exo-Brake is a simple, non-propulsive means of de-orbiting small payloads from orbital platforms such as the International Space Station (ISS). Two de-orbiting experiments with fixed surface area Exo-Brakes have been successfully conducted in the last two years on the TechEdSat-3 and -4 nano-satellite missions. The development of the free molecular flow aerodynamic data-base is presented in terms of angle of attack, projected front surface area variation, and altitude. Altitudes are considered ranging from the 400km ISS jettison altitude to 90km. Trajectory tools are then used to predict de-orbit/entry corridors with the inclusion of the key atmospheric and geomagnetic uncertainties. Control system strategies are discussed which will be applied to the next two planned TechEdSat-5 and -6 nano-satellite missions - thus increasing the targeting accuracy at the Von Karman altitude through the proposed drag modulation technique.

Exo-Brake↗
NASA NTRS1984

Explicit guidance of drag modulated aeroassisted transfer between elliptical orbits

This paper presents the complete analysis of the problem of minimum-fuel aeroassisted transfer between coplanar elliptical orbits in the case where the orientation of the final orbit is free for selection in the optimization process. The comparison between the optimal pure propulsive transfer and the idealized aeroassisted transfer, by several passages through the atmosphere, is made. In the case where aeroassisted transfer provides fuel saving, a practical scheme for its realization by one passage is proposed. The maneuver consists of three phases: a deorbit phase for nonzero entry angle, followed by an atmospheric fly-through with variable drag control and completed by a postatmospheric phase. An explicit guidance formula for drag control is derived and it is shown that the required exit speed for ascent to the final orbit can be obtained with a very high degree of accuracy.

Vinh, N. X.↗
NASA NTRS1961

The Use of Drag Modulation to Limit the Rate at Which Deceleration Increases During Nonlifting Entry

The method developed in NASA TN D-319 for studying the atmosphere entry of vehicles with varying aerodynamic forces has been applied to obtain a closed-form solution for the motion, heating, range, and variation of the vehicle parameter m/C(D)A for nonlifting entries during which the rate of increase of deceleration is limited. The solution is applicable to vehicles of arbitrary weight, size, and shape, and to arbitrary atmospheres. Results have been obtained for entries into the earth's atmosphere at escape velocity during which the maximum deceleration and the rate at which deceleration increases were limited. A comparison of these results with those of NASA TN D-319, in which only the maximum deceleration was limited, indicates that for a given corridor depth, limiting the rate of increase of deceleration and the maximum deceleration requires an increase in the magnitude of the change in M/C(D)A and results in increases in maximum heating rate, total heat absorbed at the stagnation point, and range.

Levy, Lionel L., Jr.↗
NASA NTRSDate not supplied

Performance Analysis of Magnetohydrodynamic Drag Modulation for Actively Controlled Aerocapture at Neptune

While the Ice Giants are a top priority for flagship missions in the NASA’s near-term future, current technologies limit the scientific payload and mission timeline for future Uranian and Neptunian missions due to the need for fuel for orbit insertion maneuvers. Thus, to maximize the scientific potential of future missions, atmospheric aerocapture has been heavily researched. While atmospheric aerocapture simulations have proven enabling for capturing around Neptune, its deep atmospheric pass requires an aeroshell with robust thermal protection systems (TPS). Magnetohydrodynamically-controlled aerocapture serves as a potential solution to the limitations of both fully propulsive orbit insertion and aerodynamically controlled aerocapture. Through NASA Langley’s high-fidelity flight dynamics simulation, the Program to Optimize Simulated Trajectories II, both the aerodynamic-only and magnetohydrodynamic aerocapture methods were simulated and compared for identical missions to Neptune. After applying an optimized numerical predictor-corrector guidance algorithm for both methods, the results showed that magnetohydrodynamics has not only the control authority to successfully capture around Neptune, but also the unique advantage of a shallower atmospheric pass, decreasing the maximum heat load and the required TPS mass.

Danny N. Nguyen↗
NASA NTRS2017

Guidance Scheme for Modulation of Drag Devices to Enable Return from Low Earth Orbit

Passive drag devices provide opportunities to return payloads from low Earth orbits quickly without using onboard propulsive systems to de-orbit the spacecraft. However, one potential disadvantage of such systems has been the lack of landing accuracy. Drag modulation or changing the shape of the drag device during flight offer a way to control the de-orbit trajectory and target a specific landing location. This paper discusses a candidate passive drag based system, called Exo-brake, as well as efforts to model the dynamics of the vehicle as it de-orbits and guidance schemes used to control the trajectory. Such systems can enable quick return of payloads from low Earth orbit assets like the International Space Station without the use of large re-entry cargo capsules or propulsive systems.

Dutta, Soumyo↗
NASA NTRS1961

Atmosphere Entries with Vehicle Lift-Drag Ratio Modulated to Limit Deceleration and Rate of Deceleration: Vehicles with Maximum Lift-Drag Ratio of 0.5

An analysis has been made of atmosphere entries for which the vehicle lift-drag ratio was modulated to maintain specified maximum decelerations and/or maximum deceleration rates. The part of the vehicle drag polar used during modulation was from maximum lift coefficient to minimum drag coefficient. The entries were at parabolic velocity and the vehicle maximum lift-drag ratio was 0.5. Two-dimensional trajectory calculations were made for a nonrotating, spherical earth with an exponential atmosphere. The results of the analysis indicate that for a given initial flight-path angle, modulation generally resulted in a reduction of the maximum deceleration to 60 percent of the unmodulated value or a reduction of maximum deceleration rate to less than 50 percent of the unmodulated rate. These results were equivalent, for a maximum deceleration of 10 g, to lowering the undershoot boundary 24 miles with a resulting decrease in total convective heating to the stagnation point of 22 percent. However, the maximum convective heating rate was increased 18 percent; the maximum radiative heating rate and total radiative heating were each increased about 10 percent.

Katzen, Elliott D.↗
NASA NTRS2018

Adaptive Deployable Entry Placement Technology (ADEPT) Development for Small Sat Class Venus Missions

The Adaptable, Deployable Entry and Placement Technology (ADEPT) is a novel approach for entry vehicle design. Similar to an umbrella, it is stowed during launch and deployed prior to entry. ADEPT employs a high performance, 3-D woven, carbon fabric to serve as the primary surface of the mechanically deployed system. The successful ADEPT sounding rocket flight test matured the 1-meter Class ADEPT in the areas of deployment and structural integrity, and provided aerodynamic flight characteristics of the ADEPT open-back configuration from Mach 3 to Mach 0.3. Aerocapture uses the aerodynamic drag from a single hyperbolic atmospheric pass to provide the delta-V needed for orbit insertion. Studies suggest that, compared to propulsive orbit insertion, aerocapture could increase delivered payload by 70 percent at Venus. Drag modulation aerocapture, which shows promise of being simpler and more cost-effective than the more-often studied lift modulation methods, uses in-flight transformations of an entry vehicle's drag area to control the amount of deceleration produced during an atmospheric pass. In single-event drag modulation, a drag device is jettisoned after the appropriate deceleration. ADEPT, due to its unique ability to fold and unfold, is being considered for this SmallSat class payload mission applications.

Cassell, Alan M.↗
NASA NTRSDate not supplied

Hall Magnetohydrodynamic Power Generation and Drag Augmentation Using A Coaxial-Electrode Configuration During Hypersonic Entry

For interplanetary missions, a spacecraft must reduce its relative velocity from orbital speeds of multiple kilometers per second to zero in order to safely land on the surface of a planetary body. During this phase known as planetary reentry, the spacecraft undergoes high speed above Mach 5 up to Mach 30. This hyper-sonic flight regime imposes a strong bow shock in front of the vehicle that imparts extreme aerodynamic and thermal effects. In addition, during portions of this regime, a plasma is formed in the post-shock flow-field around the vehicle due to these high temperatures. Interaction between an applied magnetic field with this electrically conductive fluid, or magnetohydrodynamic (MHD) interaction, can be utilized to convert kinetic energy from the flow into storable electrical energy. Onboard MHD energy generation can benefit the spacecraft by increasing the power of active thermal control components and vehicle control systems during reentry. MHD interaction also exerts a Lorentz body force on the plasma flow that can be manipulated to act as an additional drag force through the vehicle body. MHD drag augmentation can benefit the spacecraft with an additional control mechanism that operates without moving parts. This can be utilized at higher altitudes and subsequently reduce convective heat transfer to the vehicle. MHD interaction with plasma flow suggests that both power generation and drag augmentation can be integrated together in one design. Modern numerical studies have only demonstrated the viability and potential of MHD energy generation and drag modulation separately for implementation into future spacecraft designs [1] [2] [3]. Steeves et. al. presented one possible generator design specifically for reentry vehicles that utilized a modular panel with two embedded electromagnets and two extruding electrodes for air plasma to flow between. Fujino et. al. presented results that indicated increased total drag with a permanent magnet embedded in the blunt body of the Orbital Reentry Experiment (OREX) trajectory. Furthermore, experimental investigations of these two MHD applications have been limited and separate due to the difficult technical nature of experimental de-sign and analysis. For MHD energy generation, there have been two designs which used a cylindrical fore-body with two embedded permanent magnets and two outward facing curved electrodes for tangency to an artificially ionized plasma that flowed along the body length [4] [5]. The first design was studied using an air microwave (MW) ionized supersonic plasma wind tunnel and the second design used radio frequency (RF) ionization of Argon, but both physically demonstrated the feasibility of MHD energy generation in reentry plasma conditions. For MHD drag modulation, one study involved a small-scale cylindrical blunt body embedded with permanent magnets immersed in plasma flow in an arcjet tunnel [6], and another utilized a spherical permanent magnet enclosed with a spherical forebody that was evaluated in a shock expansion tunnel [7]. Both experimental studies provided physical evidence of drag augmentation due to MHD interactions. Therefore, because of the multi-faceted effects of MHD along with both applications having been deemed feasible and beneficial during reentry, this indicates that a coupled power generation and drag modulation design could be achievable. The axi-symmetric nature of blunt bodies for reentry suggests that a spherical set of two ring electrodes near the nose along the body axis. Based on first principles, flow along the walls of the spherical body can then produce MHD interactions between the electrodes. As a result, two currents are generated: a Hall current that produces power and a primary inductive current that augments the drag force. The goal of this work is to provide a simulated design of a coaxial-electrode con-figuration for power generation and drag modulation for experimental testing.

E. Leong↗
NASA NTRS2021

Aerocapture Trajectories for Earth Orbit Technology Demonstration and Orbiter Science Missions at Venus, Earth, Mars, and Neptune

The use of aerocapture to provide the delta-V needed to capture a spacecraft into orbit can provide significant fuel savings compared to a propulsive orbit insertion. The aerocapture guidance method described in this paper uses drag modulation, which deploys a drag skirt in the atmosphere until the amount of delta-V needed to capture into the desired orbit is obtained, at which time the drag skirt is separated from the spacecraft. By modulating the time of drag skirt jettison, the vehicle can target a specific orbit apoapsis in the presence of uncertainties such as entry targeting errors and unknown atmospheric conditions.

Jadusingh, Matt↗
NASA NTRS1979

Skylab is falling - Strategies for reentry

Planning for the Skylab reentry, options for influencing the reentry, and a discussion of the Penn State drag modulation scheme are presented. The history of and risks in connection with Skylab reentry, and the NASA and the Penn State schemes for extending Skylab life are discussed. Coordinate systems and equations of motions describing the Skylab attitude motion, aerodynamic damping, and six-degree-of-freedom simulation are considered to derive structural damping models for Skylab, and to determine if stabilization is possible, and if it is, if the TACS (attitude-control) system can retumble the vehicle. It is concluded that at least 12 hours are required to carry out the Penn State drag modulation, and natural stabilization after a period of tumbling is possible but cannot be confirmed due to limitations in the modeling of aerodynamic properties, internal damping, and atmospheric density.

Kaplan, M. H.↗