SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The phenomenon of Leaky Lamb Wave (LLW) in composite materials was first observed in 1982 using a Schlieren system. It has been studied extensively by numerous investigators and successfully shown to be an effective quantitative NDE tool.
An overview of nondestructive evaluation (NDE) is presented to indicate the availability and application potentials of techniques for quantitative characterization of the mechanical properties of structural materials. The purpose is to review NDE techniques that go beyond the usual emphasis on flaw detection and characterization. Discussed are current and emerging NDE techniques that can verify and monitor entrinsic properties (e.g., tensile, shear, and yield strengths; fracture toughness, hardness, ductility; elastic moduli) and underlying microstructural and morphological factors. Most of the techniques described are, at present, neither widely applied nor widely accepted in commerce and industry because they are still emerging from the laboratory. The limitations of the techniques may be overcome by advances in applications research and instrumentation technology and perhaps by accommodations for their use in the design of structural parts.
Numerous analytical and theoretical studies of the behavior of leaky Lamb waves (LLW) in composite materials were documented in the literature. One of the key issues that are constraining the application of this method as a practical tool is the amount of data that needs to be acquired and the slow process that is involved with such experiments. Recently, a methodology that allows quasi real-time acquisition of LLW dispersion data was developed. At each angle of incidence the reflection spectrum is available in real time from the experimental setup and it can be used for rapid detection of the defects. This technique can be used to rapidly acquire the various plate wave modes along various angles of incidence for the characterization of the material elastic properties. The experimental method and data acquisition technique will be described in this paper. Experimental data was used to examine a series of flaws including porosity and delaminations and demonstrated the efficiency of the developed technique.
Acoustic waves propagate in thin plates as guided or Lamb modes. The velocities of these modes are dispersive in that they depend not only on the material elastic properties and density, but also on the frequency. Accurate characterization of Lamb wave dispersion is important in many acoustic based nondestructive evaluation techniques. It is necessary for ultrasonic measurements in thin plates to determine elastic properties and for flaw detection and localization. In acoustic emission (AE) testing, if not taken into account, highly dispersive Lamb mode propagation can lead to large errors in source location. In this study, the pseudo Wigner-Ville distribution (PWVD) was used for measurement of group velocity dispersion of Lamb waves in a unidirectional graphite/epoxy (AS4/3502) laminate. The PWVD is one of a number of transforms which provide a time-frequency representation of a digitized time series. Broad band acoustic waves were generated by a pencil lead fracture (Hsu-Neilsen source) and were detected with broad band ultrasonic transducers. The arrival times for the lowest order symmetric (S(sub 0)) and antisymmetric (A(sub 0)) Lamb modes were determined from measurements of the time at which the respective peak amplitudes occurred in the PWVD. Measurements were made at several source-to-detector distances and a least squares fit used to calculate the velocity. Results are presented for propagation along, and perpendicular to, the fiber direction. Theoretical dispersion curves were also calculated and a comparison between theory and experiment demonstrates good agreement.
For propulsion related applications, materials must be able to demonstrate excellent ablation and oxidation resistance at temperature approaching 3500'C, adequate load bearing capabilities, non-catastrophic failure modes, and ability to withstand transient thermal shock. A potential list of propulsion-material property requirements includes, low density, high elastic modulus, low thermal-expansion coefficient, high thermal conductivity, excellent erosion and oxidation/corrosion resistance, and flaw-insensitivity. In many cases, they will also need to be able to be joined, survive thermal cycling and multi-axial stress states, and for reusable applications, the materials must maintain the above attributes after prolonged exposure to extremely harsh chemical environments. The final and possibly most important attribute for these materials are the need to be lower cost and readily available in large quantities. Recently, Advanced Ceramics Research, Inc. (ACR) has developed low cost, flexible- manufacturing processes for Zr & Hf-based carbon fiber reinforced composites, materials with good oxidation and ablation resistance up to 3500 C. This process, called Continuous Composite Co-extrusion (C(sup 3)), incorporates carbon fibers to fabricate 'in-situ' carbide and boride-matrix/carbon fiber composites. This is a variation of ACR's manufacturing process for low-cost structural ceramic materials called Fibrous Monoliths With carbon fiber reinforcements. Fibrous Monolithic materials have a distinct fibrous texture, consist of intertwined cells of a primary phase, separated by cell boundaries of a tailored secondary phase and show very high fracture energies, damage tolerance, and graceful failure. Since they are monolithic powder based composites-, they can be manufactured by conventional powder processing techniques using inexpensive raw materials. This combination of high performance and low cost is a breakthrough that could enable wider application of ceramics in high temperature applications. Typical volume fractions of the two phases are 80 to 95% for the cell phase and 5 to 20% for the interpenetrating cell boundary phase. ACR is currently developing an innovative solid freeform form fabrication (SFF) approach to produce Hf and Zr based ceramic composite components reinforced with continuous carbon fiber tows for critical structural components such as tubes and blisks. The process is simple, robust and will be widely applicable to a number of material systems. This technique was originally developed at the University of Delaware Center for Composite Materials (UD-CCM) for rapid fabrication of polymer matrix composites by a technique called automated tow placement or ATP. The current process is being developed in collaboration with UD-CCM. The paper will detail the freeform fabrication process to create low-cost ceramic fiber reinforced composites for high-temperature applications. The results of mechanical properties and microstructural characterization will be presented, together with examples of complex shapes and parts. It is believed that the process will be able to create complex shaped parts for propulsion applications at an order of magnitude lower cost than current CVI and PIP process.
For propulsion related applications, materials must be able to demonstrate excellent ablation and oxidation resistance at temperature approaching 3500 C, adequate load bearing capabilities, non-catastrophic failure modes, and ability to withstand transient thermal shock. A potential list of propulsion-material property requirements includes, low density, high elastic modulus, low thermal-expansion coefficient, high thermal conductivity, excellent erosion and oxidation/corrosion resistance, and flaw-insensitivity. In many cases, they will also need to be able to be joined, survive thermal cycling and multi-axial stress states, and for reusable applications, the materials must maintain the above attributes after prolonged exposure to extremely harsh chemical environments. The final and possibly most important attribute for these materials are the need to be lower cost and readily available in large quantities. Recently, Advanced Ceramics Research, Inc. (ACR) has developed low cost, flexible-manufacturing processes for Zr & Hf-based carbon fiber reinforced composites, materials with good oxidation and ablation resistance up to 3500 C. This process, called Continuous Composite Co-extrusion (C(sup 3)), incorporates carbon fibers to fabricate 'in-situ' carbide and boride-matrix/carbon fiber composites. M is a variation of ACR's manufacturing process for low-cost structural ceramic materials called Fibrous Monoliths with carbon fiber reinforcements. Fibrous Monolithic materials have a distinct fibrous texture, consist of intertwined cells of a primary phase, separated by cell boundaries of a tailored secondary phase and show very high fracture energies, damage tolerance, and graceful failure. Since they are monolithic powder based composites; they can be manufactured by conventional powder processing techniques using inexpensive raw materials. This combination of high performance and low cost is a breakthrough that could enable wider application of ceramics in high temperature applications. Typical volume fractions of the two phases are 80 to 95% for the cell phase and 5 to 20% for the interpenetrating cell boundary phase. ACR is currently developing an innovative solid freeform form fabrication (SFF) approach to produce Hf and Zr based ceramic composite components reinforced with continuous carbon fiber tows for critical structural components such as tubes and blisks. The process is simple, robust and will be widely applicable to a number of material systems. This technique was originally developed at the University of Delaware Center for Composite Materials (UD-CCM) for rapid fabrication of polymer matrix composites by a technique called automated tow placement or ATP. The current process is being developed in collaboration with UD-CCM. The paper will detail the freeform fabrication process to create low-cost ceramic fiber reinforced composites for high-temperature applications. The results of mechanical properties and microstructural characterization will be presented, together with examples of complex shapes and parts. It is believed that the process will be able to create complex shaped parts for propulsion applications at an order of magnitude lower cost than current CVI and PIP processes.