Search NASA⌕ Search

SEARCH · Search NASA

Results for “elastomer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2016

Compatibility Assessment of Fuel System Elastomers with Bio-oil and Diesel Fuel

Bio-oil derived via fast pyrolysis is being developed as a renewable fuel option for petroleum distillates. The compatibility of neat bio-oil with six elastomer types was evaluated against the elastomer performance in neat diesel fuel, which served as the baseline. The elastomers included two fluorocarbons, six acrylonitrile butadiene rubbers (NBRs), and one type each of fluorosilicone, silicone, styrene butadiene rubber (SBR), polyurethane, and neoprene. Specimens of each material were exposed to the liquid and gaseous phases of the test fuels for 4 weeks at 60 degrees C, and properties in the wetted and dried states were measured. Exposure to bio-oil produced significant volume expansion in the fluorocarbons, NBRs, and fluorosilicone; however, excessive swelling (over 80%) was only observed for the two fluorocarbons and two NBR grades. The polyurethane specimens were completely degraded by the bio-oil. In contrast, both silicone and SBR exhibited lower swelling levels in bio-oil compared to neat diesel fuel. The implication is that, while polyurethane and fluorocarbon may not be acceptable seal materials for bio-oils, silicone may offer a lower cost alternative.

09 BIOMASS FUELS↗
DOE OSTI2021

Light-Mediated Synthesis and Reprocessing of Dynamic Bottlebrush Elastomers under Ambient Conditions

We introduce a novel grafting-through polymerization strategy to synthesize dynamic bottlebrush polymers and elastomers in one step using light to construct a disulfide-containing backbone. The key starting material—α-lipoic acid (LA)—is commercially available, inexpensive, and biocompatible. When installed on the chain end(s) of poly(dimethylsiloxane) (PDMS), the cyclic disulfide unit derived from LA polymerizes under ultraviolet (UV) light in ambient conditions. Significantly, no additives such as initiator, solvent, or catalyst are required for efficient gelation. Formulations that include bis-LA-functionalized cross-linker yield bottlebrush elastomers with high gel fractions (83–98%) and tunable, supersoft shear moduli in the ~20–200 kPa range. An added advantage of these materials is the dynamic disulfide bonds along each bottlebrush backbone, which allow for light-mediated self-healing and on-demand chemical degradation. These results highlight the potential of simple and scalable synthetic routes to generate unique bottlebrush polymers and elastomers based on PDMS.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Controlled Placement of Microparticles at the Water–Liquid Crystal Elastomer Interface

Control of cells behavior through topography of substrates is an important theme in biomedical applications. Among many materials used as substrates, polymers show advantages since they can be tailored by chemical functionalization. Fabrication of polymer substrates with nano- and microscale topography requires processing by lithography, microprinting, etching, etc. In this work, we introduce a different approach based on anisotropic elastic properties of polymerized smectic A (SmA) liquid crystal elastomer (LCE). When the SmA liquid crystal coating is deposited onto a substrate with planar alignment of the molecules, it develops nanogrooves at its free surface. After photopolymerization, these nanogrooves show an excellent ability to align human dermal fibroblasts (hDFs) over large areas. The alignment quality is good for both bare SmA LCE substrates and for substrates coated with fibronectin. The SmA LCE nano-topographies show a high potential for tissue engineering.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Command of active and responsive elastomers by topological defects and patterns

The project resulted in the development of stimuli-responsive elastomer coatings formed by photopolymerized liquid crystal molecules. The molecular orientation of the liquid crystal elastomers is coupled to rubber-like elasticity. The project developed an approach to produce complex patterns of molecular orientation in elastomers by employing photopatterning technique based on plasmonic metamasks that convert unpolarized incoming light into a transmitted light beam with spatially-varying linear polarization. The polarization-modulated light beam aligns the film of azodye molecules, which serves as the substrate for liquid crystal elastomer coating. The alignment of the azodye molecules follows the polarization pattern with a phase shift of the alignment direction by 90 degrees. The azodye substrate imposes orientation of molecules in the adjacent liquid crystal layer which is preserved after the monomers are polymerized into a liquid crystal elastomer. By using differently aligned substrates one could produce various patterns of molecular orientation in the elastomer, which dictate the mechanical properties of the elastomers and their response to external stimuli such as temperature, humidity, and ultraviolet irradiation. In particular, the predesigned molecular orientation produces deterministically defined topography response of the liquid crystal coatings, in which their free surface changes from flat to either locally elevated or locally compressed, depending on whether the pre-inscribed molecular orientation is predesigned with a splay or bend deformation. The research established that the mechanism of this deterministic relation between the dynamic topography and pre-inscribed molecular orientation is rooted in the change of the tensorial order parameter that characterizes the degree of orientational order, and in the contraction/expansion of polymer molecules in response to the order parameter changes. In particular, lowering the order causes contraction of polymer globules. The work demonstrated that the dynamic topography of elastomer coatings with three-dimensional pattern of orientational order includes up and down motion of the material (along the normal to the coating) and also shifts in lateral directions. We demonstrate that the deterministic relationship between the orientational patterns and variations of coatings’ profile is caused by forces that are mathematically equivalent to active forces in the system of “pullers” or “pushers” in active matter, demonstrating universality of the out-of-equilibrium behavior. The project resulted in theoretical models that predictively describe the dynamic response of coatings. The topography of liquid crystal elastomers is sensitive to stimuli such as temperature, ultraviolet irradiation, and humidity. The applicability of the patterned approach to produce dynamic coatings was expanded from nematic elastomers to their smectic counterparts. The project combined a battery of imaging techniques to unveil the dynamic properties of the coatings, ranging from the state-of-the-art dynamic holographic microscopy to fluorescent confocal polarizing microscopy and polscope microscopy. The research uncovered potential applications of dynamic elastomer coatings, such as control placement of colloidal particles, engineering of living tissues with alignment patterns of cells that follow the orientational order of elastomer coatings. The approach developed in the project can be used to design programmable dynamic coatings with functionalities that mimic biological tissues such as skin.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Autonomous Self-Healing Elastomers with Unprecedented Adhesion Force

Self-healable elastomers are extremely attractive due to their ability to prolong product lifetime. An additional function that could further expand their applications is strong adhesion force to clean and dusty surfaces. This study reports a series of autonomous self-healable and highly adhesive elastomers (ASHA-Elastomer) that are fabricated via a simple, efficient, and scalable process. The obtained elastomers exhibit outstanding mechanical properties with elongation at break up to 2102% and toughness (modulus of toughness) of 1.73 MJ m -3 . The damaged ASHA-Elastomer can autonomously self-heal with full recovery of functionalities, and the healing process is not affected by the presence of water. The elastomers are found to possess an ultrahigh adhesion force up to 3488 N m -1 , greatly outperforming previously reported self-healing adhesive elastomers. Furthermore, the adhesion force of the ASHA-Elastomer is negligibly affected by dust on the surface, in stark contrast with regular adhesive polymers that have adhesion strengths extremely sensitive to dust. The successful development of high-toughness, autonomous self-healable, and ultra-adhesive elastomers will enable a wide range of applications with enhanced longevity and versatility, including their use in sealants, adhesives, and stretchable devices.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Ductile adhesive elastomers with force-triggered ultra-high adhesion strength

Elastomers play a vital role in many forthcoming advanced technologies in which their adhesive properties determine materials’ interface performance. Despite great success in improving the adhesive properties of elastomers, permanent adhesives tend to stick to the surfaces prematurely or result in poor contact depending on the installation method. Thus, elastomers with on-demand adhesion that is not limited to being triggered by UV light or heat, which may not be practical for scenarios that do not allow an additional external source, provide a solution to various challenges in conventional adhesive elastomers. Herein, we report a novel, ready-to-use, ultra high-strength, ductile adhesive elastomer with an on-demand adhesion feature that can be easily triggered by a compression force. The precursor is mainly composed of a capsule-separated, two-component curing system. After a force-trigger and curing process, the ductile adhesive elastomer exhibits a peel strength and a lap shear strength of 1.2 × 10 4 N m -1 and 7.8 × 10 3 kPa, respectively, which exceed the reported values for advanced ductile adhesive elastomers. The ultra-high adhesion force is attributed to the excellent surface contact of the liquid-like precursor and to the high elastic modulus of the cured elastomer that is reinforced by a two-phase design. In conclusion, incorporation of such on-demand adhesion into an elastomer enables a controlled delay between installation and curing so that these can take place under their individual ideal conditions, effectively reducing the energy cost, preventing failures, and improving installation processes.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Compatibility of Fuel System Elastomers and Plastics with a Fast-Pyrolysis Oil (Bio-oil) at Room Temperature

Herein the compatibility of a fast-pyrolysis bio-oil with 17 elastomer and 21 plastic materials common to fuel storage, dispensing, and delivery systems was assessed by measuring volume and hardness. Diesel was used as the baseline for comparison. The elastomer and plastic specimens were exposed to the test fuels at 23 °C. The exposure times were 4 and 16 weeks for the elastomers and plastics, respectively. The elastomers (except for silicone and styrene butadiene) exhibited pronounced swelling in the bio-oil. This was especially true for the fluorocarbons and acrylonitrile rubbers. For the elastomers, a strong correlation between polarity and volume swell was observed. Compositional and structural analysis on one of the fluorocarbon materials showed that the bio-oil was less effective at extracting phthalate additives than the diesel. However, the crystallinity of a fluorocarbon was altered by the bio-oil. Unlike the elastomers, the plastic materials were less impacted by exposure to the bio-oil. This finding is attributed to their denser and more rigid molecular structures (compared to the elastomers). Notable swelling did occur in the nylons, but this swelling was attributed to water absorption rather than polarity. Comparison with previous studies showed that the observed swelling was lower for both the elastomers and the plastics. Solubility (and hence swell) increases with temperature, and because this study was conducted at 23 °C rather than 50 °C, the reduced temperature is responsible for the lower swell levels.

09 BIOMASS FUELS↗
DOE OSTI2020

Compatibility of Elastomers with Polyoxymethylene Dimethyl Ethers and Blends with Diesel

Polyoxymethylene dimethyl ethers (PODEs) have shown promise as candidates for diesel fuel blendstocks due to their low sooting tendency, high cetane number, and diesel-comparable boiling point range. However, there is a lack of literature regarding compatibility of PODEs with common automotive elastomers, which would be a prerequisite to their adoption into the marketplace. To address this need, an exposure study and complementary solubility analysis were undertaken. A commercially available blend of PODEs with polymerization degree ranging from 3 to 6 was blended with diesel certification fuel at 0, 33, 50, 67, at 100% by mass. Elastomer coupons were exposed to the various blends for a period of 4 weeks and evaluated for volume swell. The elastomer materials included multiple fluoroelastomers (Viton and fluorosilicone) and acrylonitrile butadiene rubbers (NBR), as well as neoprene, polyurethane, epichlorohydrin (ECO), PVC-nitrile blend (OZO), ethylene propylene diene monomer (EPDM), styrene-butadiene rubber (SBR), and silicone. The exposure results indicated overall poor compatibility for PODE, with every elastomer except for fluorosilicone exhibiting greater than 30% volume swell at the 33% blend level. The general trend across the elastomers was either a consistent increase in volume swell with PODE concentration, or maximum in volume swell at an intermediate blend fraction. One notable exception is EPDM, which is not generally compatible with diesel fuel and which exhibited a reduction in volume swell with increasing PODE concentration. The same elastomers and PODE/diesel blends were evaluated using Hansen solubility parameter analysis, which predicted similar trends to the exposure study with the exception of ECO. From these results, we conclude that adoption of PODEs as a diesel fuel blendstock will require either the development of specialized elastomers, or that the blend fraction be kept to a low level to maintain compatibility with existing elastomers.

42 ENGINEERING↗
DOE OSTI2019

Failure of brittle micro-spherical shells embedded in elastomer matrix under indentation

Silicone elastomer filled with glass micro balloons (GMB) is an elastomeric syntactic foam used in electronics and component packaging for encapsulation, potting, stress-relief layer, and electrical insulation purposes. Under mechanical loading, the reinforcing phase, namely the GMBs embedded in the elastomer matrix, may break or delaminate, leading to internal damage and macroscale stiffness degradation, which can alter the material's protective capacity against mechanical shock and vibration. The degree of damage is controlled by the loading history, delamination, and failure behavior of the GMBs. In this work, we investigate the GMB failure behavior in this work wherein we present an indentation experiment to measure the force required to fail individual GMBs that are either embedded in the elastomer matrix or adhered to the surface of an elastomer layer. The indentation apparatus is augmented with an inverted optical microscope to enable in situ imaging of the GMB. Failure modes for the embedded or non-embedded GMBs are discussed based on the morphology of the broken GMBs and the measured failure forces. We also measure the adhesion energy between the glass balloon and the elastomer, based on which the possibility of delamination between the GMB and the surrounding elastomer matrix during the failure process is evaluated. Our results can facilitate the development of a failure criterion of GMBs which is necessary for establishing a physics-based constitutive model to describe the macroscopic damage mechanics of elastomeric syntactic foams.

42 ENGINEERING↗
DOE OSTI2021

Three-Dimensional Printable, Extremely Soft, Stretchable, and Reversible Elastomers from Molecular Architecture-Directed Assembly

3D printing elastomers enables the fabrication of many technologically important structures and devices such as tissue scaffolds, sensors, actuators, and soft robots. However, conventional 3D printable elastomers are intrinsically stiff; moreover, the process of printing often requires external mechanical support and/or post-treatment. In this work, we exploit the self-assembly of a responsive linear-bottlebrush-linear triblock copolymer to create stimuli-reversible, extremely soft, and stretchable elastomers and demonstrate their applicability as inks for in situ direct-write printing 3D structures without the aid of external mechanical support or post-treatment. By developing a procedure for controlled synthesis of such architecturally designed block copolymers, we create elastomers with extensibility up to 600% and Young’s moduli down to ~10 2 Pa, 10 6 times softer than plastics and more than 102 times softer than all existing 3D printable elastomers. Moreover, the elastomers are thermostable and remain to be solid up to 180 °C, yet they are 100% solvent-reprocessable. Their extreme softness, stretchability, thermostability, and solvent-reprocessability bode well for future applications.

36 MATERIALS SCIENCE↗