SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Electrical, mechanical, and thermo-physical properties of conductor and insulation materials for application to advanced space electric power systems
Magnetic, electric conductor, electric insulation, and bore seal materials for advanced space electric power systems
Magnetic, mechanical, and thermophysical property data on magnetic materials for use in advanced space electric power systems
Commercial electrical conductor wires are currently produced from aluminum alloys by multi-step deformation processing involving rolling and drawing. These processes typically require 10 to 20 steps of deformation, since the plastic strain or reduction that can be imposed in a single step is limited by material workability and process mechanics. Here, we demonstrate a fundamentally different, single-step approach to produce flat wire aluminum products using machining-based deformation that also ensures adequate material workability in the formed product. Two process routes are proposed: (1) chip formation by free-machining (FM), with a post-machining, light drawing reduction (<20%) to achieve desired finish and (2) constrained chip formation by large strain extrusion machining (LSEM). Using commercially pure aluminum conductor alloys (Al 1100 and EC1350) as representative material systems, we demonstrate key features of the machining-based processing, including (a) single-step processing to achieve flat wire geometries, (b) surface finish (Ra = 0.2 to 1.0 μm) comparable to that of commercial wire products made by drawing/rolling, (c) deformation control independent of wire size, and (d) hardness increases of 50–150% over that of annealed wires, while retaining high electrical conductivity (>56% IACS). Here, the wire microstructure, which can also be varied via the large-strain deformation parameters, is correlated with mechanical and electrical properties. Implications for commercial manufacture of flat wire products are discussed.
Dielectric coatings for electrical conductors at cryogenic temperatures
Low temperature dielectric coatings for electric conductors
Tungsten fiber-reinforced copper composites have tensile strength, yield strength, and modulus of elasticity proportional to fiber content. The composites form high strength electrical conductors.
Arch-shaped conductors fabricated from flat strips of beryllium oxide dispersion-strengthened copper alloy serve as flexible electrical connectors capable of operating in 1000 deg F temperature range, under vacuum conditions for periods of 10,000 hours or more without failure.
This study demonstrates the versatility of Joule heating driven chemical vapor deposition to deposit nanometal interconnections into porous CNT roving with application in the production of high electrical conductivity copper-carbon nanotube (Cu-CNT) hybrids. Modifications of vapor deposition parameters allow for deposited nanometal masses from less than 5% w/w to over 85% w/w and distributions that can be controlled towards either hot-spot site-specificity or overall uniformity. Here, depositions of copper, platinum, nickel, palladium, ruthenium, rhodium, and iridium are demonstrated from acetylacetonate precursors. In particular, platinum acetylacetonate [Pt(acac) 2 ] deposits nanometal seeds that adhere tightly to the CNT roving, producing improvements in resistance and specific conductivity. The properties of the platinum deposition compared to the copper deposition motivate an investigation into its use as an interfacial layer for Cu-CNT hybrids. CNT conductors with ~30% w/w platinum are electroplated with copper, densified, and annealed to produce Cu-CNT hybrid conductors with specific conductivities as high as 5772 S m 2 /kg and TCR (from 300 to 600 K) as low as 3.12 × 10 –3 K –1 , indicating good interconnection of the metal and CNT portions. Room temperature conductivities of 29.8 MS/m are achieved, comparable to metallic conductors. Thus, Pt(acac) 2 seeded Cu-CNT hybrids offer abundant promise in high conductivity applications.
The characteristics of carbon fibers (CF) made from polyacrylonitrile (PAN) materials are discussed, together with research on conducting polymers. CF materials have better mechanical properties, chemical inertness, and higher stiffness than metallic materials but are subject to environmental instability, flammability, and delamination fatigue. Polymerization procedures for the monopolymer PAN are described, noting the use of SEM and X-ray diffraction techniques for studying the fiber structure. High modulus and strength of CF are caused by covalent sp(2) bonds in hexagonal carbon rings, which are stronger than the same links in diamonds. Details of the molecular chain structures and macroformations, stress-strain as a function of temperature, and thermosetting and glass transition temperatures of polymers are provided. Computational quantum chemistry techniques are being applied to studying electrical conductance in polymers, mainly to discover ways to stabilize the materials. Doped CH(x) has exhibited photovoltaic properties and other polymers have become superconductors at cryogenic temperatures.
Three methods for applying ceramic coatings to wires were examined in depth and a fourth (chemical vapor deposition) was studied briefly. CVD coatings were not reported in the thesis because it was realized early in the study that the deposition rate of the coatings was too slow to be used in a commercial process. Of the methods reported in the thesis, slurry coating was the most promising. This method consists of slowly drawing a platinum wire through a thixotropic slurry of alumina in a vehicle composed of polyvinyl butyral, methyl ethyl ketone, and toluene. The coatings produced by this method were continuous and free of cracks after sintering. The sintered coatings crack when the wire is bent around sharp corners, but most of the coating remains in place and still provides electrical insulation between the wire and any metallic structure to which the wire may be attached. The coating thickness was 0.61 mm (16 micrometers). The electrical resistivity of the intact coating was 340 M-Ohm-cm at 800 C and 23 M-Ohm-cm at 1050 C. Therefore, these coatings more than meet the electrical requirements for use in turbine engines. Although adherence of the coating to the wire was generally excellent, a problem was noted in localized areas where the coating flaked off. Further work will be needed to obtain good coating adherence along the entire length of the wire. The next most promising coatings were made by electrophoretic deposition (EPD) of Al2O3 onto platinum wires, using mixtures of ethanol and acetone as the suspending liquid. These EPD coatings were made only on short lengths of wire because the coating is too fragile to allow spooling of the wire. The worst coatings were those made by electrophoretic deposition from aqueous suspensions. Continuous slurry coating of wire was achieved, but due to lack of suitable equipment, the wire had to be cut into short lengths for sintering.
Eddy current sensors measure the lift-off or distance between the sensor and a conducting surface. They operate on the principle of an alternating current in a conduction coil inducing a magnetic field within the surface. An eddy current is set up in the surface to counter the incident magnetic field which, in turn, sets up a magnetic field which counters that of the coil. This changes the coil impedance which is a function of the lift-off. As the lift-off increases, the effect of the eddy current magnetic field on the coil magnetic field weakens, resulting in a higher inductance and lower resistance. Thus, the lift-off may be derived from an impedance measurement. Dodd and Deeds developed an analytic model for an eddy current sensor coil impedance with an air core which has been implemented in MATLAB. LLNL assembled an eddy current sensor with a mu-metal core for which there is no analytic model. Rather than derive an analytic model which includes the mu-metal core, analytic empirically based functions are derived to map the Dodd and Deeds model to measured inductance and resistance.
Explore the source record for details and available documents.
Dielectric loss and connector problems at cryogenic temperature
Explore the source record for details and available documents.
Performance tests of flexible conductor high temperature switches
For years NASA has wanted to reduce the weight of spacecraft and aircraft. Experiments are conducted to find a lightweight synthetic metal to replace copper. The subject of this paper, intercalated graphite, is such a material. Intercalated graphite is made by heating petroleum or coal to remove the hydrogen and to form more covalent bonds, thus increasing the molecular weight. The coal or petroleum eventually turns to pitch, which can then be drawn into a fiber. With continued heating the pitch-based fiber releases hydrogen and forms a carbon fiber. The carbon fiber, if heated sufficiently, becomes more organized in parallel layers of hexagonally arranged carbon atoms in the form of graphite. A conductor of intercalated graphite is potentially useful for spacecraft or aircraft applications because of its low weight.
A wireless electrical device includes an electrically unconnected electrical conductor and at least one electrically unconnected electrode spaced apart from the electrical conductor. The electrical conductor is shaped for storage of an electric field and a magnetic field. In the presence of a time-varying magnetic field, the electrical conductor so-shaped resonates to generate harmonic electric and magnetic field responses. Each electrode is at a location lying within the magnetic field response so-generated and is constructed such that a linear movement of electric charges is generated in each electrode due to the magnetic field response so-generated.