Electrochemical engineering
Overpotential transients on rotating disk, current and potential distributions in cylinders, foamed electrolyte fuel cell, atomic scale electrode processes, and charge transfer complexes
Bockris, J. O.↗
SEARCH · Search NASA
Results for “electrochemical overpotential”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Electrochemical behavior of the boron anode in aqueous solutions
The electrochemical oxidation of p-type boron in 0.2 N NaNO3 solutions of pH 0.4 to 13.1 was studied by galvanostatic techniques. The capacitance of the electrode, Tafel slopes, and a limited analysis of reaction mechanisms are reported. The anodic dissolution in acid solution is a charge-transfer-limited one-electron reaction to form a monovalent species in the over-potential region of 0.25 to 0.70 V. The dissolution in basic solution is most probably a one-electron charge-transfer reaction from a monovalent to divalent species involving three hydroxyl ions. Open circuit potentials were mixed potentials, probably due to hydrogen formation at open circuit but not contributing to the electrochemical reaction at the applied overpotential. Exchange current, estimated by extrapolation of the Tafel line to the standard oxidation potential for the boron reaction, were of the order of 10 to the minus 6th power A/cm2 in acid solution and 10 to the minus 12th power A/cm2 in basic solution. The reaction order of the rate determining acidic and basic reactions was determined with regard to (H+) and (OH-). The level of illumination had no effect on the electrochemical behavior of the electrode.
Delduca, B. S.↗
Overpotential-time variation for galvanostatic charging with potential dependent capacitance
Approximation method solution of nonlinear differential equation for time variation of overpotential during galvanostatic charging in electrochemical cell
ELECTROCHEMICAL CELL↗
The molten carbonate carbon dioxide concentrator - Cathode performance at high CO2 utilization
An experimental study of the cathode performance of the molten carbonate carbon dioxide concentrator (MCCDC) at typical gas concentrations is reported, and the behavior is described in terms of standard electrochemical kinetic analysis. Theoretical aspects of the MCCDC are discussed, including the current-generating processes, the overpotential, and the reaction kinetics. A final working equation is derived, and the electrochemical cell is described. The parameters determined by the experiments include cathode overpotentials and removal and current efficiency as a function of current density, as well as carbon dioxide removal rate as a function of flow rate. The results are compared with data for other cells; the agreement with data for the molten carbonate fuel cell suggests that the major difference between the two cells is in the wetting characteristics. The MCCDC achieves high removal efficiencies at high current efficiencies. The lowest current efficiency recorded was 80 percent, and at most current densities, current efficiencies were above 100 percent.
Weaver, J. L.↗
Frequency response of electrochemical cells
Impedance concepts can be applied to the analysis of battery electrodes, yielding information about the structure of the electrode and the processes occurring in the electrode. Structural parameters such as the specific area (surface area per gram of electrode) can be estimated. Electrode variables such as surface overpotential, ohmic losses, and diffusion limitations may be studied. Nickel and cadmium electrodes were studied by measuring the ac impedance as a function of frequency, and the specific areas that were determined were well within the range of specific areas determined from BET measurements. Impedance spectra were measured for the nickel and cadmium electrodes, and for a 20 A-hr NiCd battery as functions of the state of charge. More work is needed to determine the feasibility of using frequency response as a nondestructive testing technique for batteries.
Thomas, Daniel L.↗
Multiphysics Modeling of Electrode Dissolution under Hydrodynamic Conditions in Low Conductivity Water
Efficient plug-flow electrochemical reactors are characterized by their ability to effectively convert species with significant ionic strength and/or with the assistance of a well-behaved electrolyte. Because of the classic electroconductivity requirement, electrochemical reactors are not particularly attractive options for applications with low-conductivity conditions, especially for low-pressure feeds. However, these reactors can still find application in dedicated processes such as ultra-clean water conditioning and biological-coupled separation systems. Consequently, a multi-physics model was developed using COMSOL Multiphysics to characterize different reactor-design conditions based on the Tertiary Current Distribution which accounts for the effects of expected variations in electrolyte composition and ionic strength on the electrochemical process, as well as solution resistance and electrode kinetics. The modelling framework presented here employs single-phase laminar fluid flow, the Nernst-Planck equation, the water-based electroneutrality condition, and concentration-dependent overpotentials. This investigation particularly explores the electrolysis process of “anodic dissolution,” in which elemental species dissociate from the solid matrix of the electrode and enter the liquid phase of the electrolyte as soluble ions. The reactor configuration of interest has a rectangular parallel-electrode design and is operated galvanostatically. A series of parametric studies are carried out to inspect the response of the system when hydrodynamic, kinetic, and geometric conditions are changed. The parametric sweep resulted in variable effluent concentrations and system voltage, which reveal underlaying optimization patterns for electrode dissolution in low conductivity water.
Multiphysics↗
Electrochemical generation of oxygen. 1: The effects of anions and cations on hydrogen chemisorption and anodic oxide film formation on platinum electrode. 2: The effects of anions and cations on oxygen generation on platinum electrode
The effects were studied of anions and cations on hydrogen chemisorption and anodic oxide film formation on Pt by linear sweep voltammetry, and on oxygen generation on Pt by potentiostatic overpotential measurement. The hydrogen chemisorption and anodic oxide film formation regions are greatly influenced by anion adsorption. In acids, the strongly bound hydrogen occurs at more cathodic potential when chloride and sulfate are present. Sulfate affects the initial phase of oxide film formation by produced fine structure while chloride retards the oxide-film formation. In alkaline solutions, both strongly and weakly bound hydrogen are influenced by iodide, cyanide, and barium and calcium cations. These ions also influence the oxide film formation. Factors considered to explain these effects are discussed. The Tafel slope for oxygen generation was found to be independent on the oxide thickness and the presence of cations or anions. The catalytic activity indicated by the exchange current density was observed decreasing with increasing oxide layer thickness, only a minor dependence on the addition of certain cations and anions was found.
Huang, C. J.↗
Study of the zinc-silver oxide battery system
Theoretical and experimental models for the evaluation of current distribution in flooded, porous electrodes are discussed. An approximation for the local current distribution function was derived for conditions of a linear overpotential, a uniform concentration, and a very conductive matrix. By considering the porous electrode to be an analog of chemical catalyst structures, a dimensionless performance parameter was derived from the approximated current distribution function. In this manner the electrode behavior was characterized in terms of an electrochemical Thiele parameter and an effectiveness factor. It was shown that the electrochemical engineering approach makes possible the organizations of theoretical descriptions and of practical experience in the form of dimensionless parameters, such as the electrochemical Thiele parameters, and hence provides useful information for the design of new electrochemical systems.
Nanis, L.↗
The application of electrochemical impedance spectroscopy for characterizing the degradation of Ni(OH)2/NiOOH electrodes
Electrochemical impedance spectra of rolled and bonded and sintered porous nickel battery electrodes were recorded periodically during charge/discharge cycling in concentrated KOH solution at various temperatures. A transmission line model (TLM) was adopted to represent the impedance of the porous electrodes, and various model parameters were adjusted in a curve fitting routine to reproduce the experimental impedances. Degradation processes for rolled and bonded electrodes were deduced from changes in model parameters with electrode cycling time. In developing the TLM, impedance spectra of planar (non-porous) electrodes were used to represent the pore wall and backing plate interfacial impedances. These data were measured over a range of potentials and temperatures, and an equivalent circuit model was adopted to represent the planar electrode data. Cyclic voltammetry was used to study the characteristics of the oxygen evolution reaction on planar nickel electrodes during charging, since oxygen evolution can affect battery electrode charging efficiency and ultimately electrode cycle life if the overpotential for oxygen evolution is sufficiently low. Transmission line modeling results suggest that porous rolled and bonded nickel electrodes undergo restructuring during charge/discharge cycling prior to failure.
Macdonald, D. D.↗
Alternative Electrochemical Systems for Ozonation of Water
Electrochemical systems that are especially well suited for the small-scale generation of ozone and ozonated water for local use have been invented. These systems can operate with very little maintenance, and the only inputs needed during operation are electric power and water. Ozonated water produced by these systems can be used in diverse industrial applications: A few examples include sterilization in the brewing industry, general disinfection, and treatment of sewage and recycled water. The basic principle of operation admits of several alternative system configurations. The heart of the system is a stack of electrolytic cells, each containing a proton-exchange membrane (which serves as a solid electrolyte) sandwiched between a catalytic anode and a catalytic cathode. Preferably, the proton-exchange membrane is made of a perfluorinated sulfonic acid polymer. During electrolysis, a mixture of O2 and O3 gases is generated at the anode and H2 is generated at the cathode. Some of the O3 generated at the anode becomes dissolved in the water. The proportion of O3 in the O2/O3 mixture can be maximized by the selection of suitable electrode materials and the use of a high overpotential. Although the proton-exchange membrane conducts protons, it does not conduct electrons. It is also impermeable by gases; consequently, it maintains separation between the O2/O3 mixture evolved at the anode and the H2 evolved at the cathode.
Andrews, Craig C.↗