Atomic-scale Feedback-controlled Electron Beam Fabrication of 2D Materials
Explore the source record for details and available documents.
Boebinger, Matthew↗
SEARCH · Search NASA
Results for “electron beam fabrication”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Creep Behavior of a High-$\gamma^{\prime}$ Ni-Based Superalloy Fabricated via Electron Beam Melting
Additive manufacturing enables the fabrication of complex engineering components previously inaccessible through traditional processes. Nickel-base superalloys with large γ' volume fraction are typically considered non-weldable and therefore exhibit a propensity for cracking during the fusion process. These crack-prone materials, however, are of great importance in gas turbine engines due to their excellent high temperature creep resistance. In this study we investigate the creep behavior of IN738LC produced by the electron beam melting process. Here, we find that with appropriate post-build heat treatment the creep response of material oriented in the build direction exhibits deformation and rupture behavior comparable to that of conventionally cast IN738 & IN738LC. In the transverse direction properties fall below the expected cast behavior, however, we argue this is likely due to differences in grain scale and crystallographic texture. It may be possible to coarsen the grain morphology with appropriate process-parameter optimization in order to reduce the severity of intergranular fracture in the transverse direction. These results illustrate that high temperature properties exhibited by additively manufactured IN738LC are suitable for the hot section of gas turbine engines.
36 MATERIALS SCIENCE↗
Creep behavior of $\gamma$-TiAl fabricated via electron beam additive manufacturing
$\gamma$-TiAl is a desirable structural engineering alloy with excellent high temperature specific strength. This material system has been shown to be processable at industrial scales via additive manufacturing. In this work we investigate the microstructure and properties of Ti48Al2Cr2Nb fabricated via electron beam melting. No significant anisotropy was observed from during creep testing under the considered conditions. Creep deformation resistance and rupture strength are comparable to material synthesized via traditional routes.
Fernandez-Zelaia, Patxi↗
Multimodal Defect Imaging of Pure Tungsten Components Fabricated via Electron Beam Powder Bed Fusion
The utilization of additive manufacturing (AM) techniques for refractory materials in high-temperature environments has significantly expanded because of the ability to fabricate geometrically complex components. Electron beam powder bed fusion (EB-PBF), which provides lower residual stress, a cleaner vacuum environment, and better efficiency for high melting point, is one of the best-suited AM methods to produce advanced refractory components. However, the property variation attributed to the heterogeneous microstructure and process-induced defects has hindered the widespread adoption of EB-PBF-produced material like tungsten. While numerous in-situ monitoring and defect detection methods have been demonstrated for EB-PBF, a workflow that compares and evaluates process-induced abnormalities from different imaging perspectives is still limited. This study examines a feature-embedded tungsten component manufactured via the EB-PBF process to demonstrate the defect detection capabilities of a multimodal defect imaging workflow. The predefined and process-induced defects are evaluated by harnessing various imaging techniques, including in-situ electron imaging, layerwise near-infrared (NIR) imaging, post-build high-energy x-ray computed tomography (CT), and conventional destructive metallography. The results highlight the strengths and limitations of distinctive defect imaging techniques concerning specific defect types, sizes, and conditions. It was found that electron imaging can provide more abnormal detection capabilities while maintaining a higher measuring accuracy, against the conventional metallography in this case study, compared with NIR and CT imaging techniques.
36 MATERIALS SCIENCE↗
Nickel-based superalloy single crystals fabricated via electron beam melting
Additive manufacturing technologies have emerged as potential disruptive processes whose possible impacts range from supply chain logistics, prototyping, and novel materials synthesis. Numerous works illustrate the ability to control mi- crostructure in fusion based processes and a few recent authors have even produced single crystals. However, a number of open questions remain regarding the process window which enables printing of single crystals. Furthermore, it has been observed that these additively manufactured single crystals exhibit a preferred $\langle$011$\rangle$ secondary orientation. In this work we investigate fabrication conditions which enable printing of single crystals via electron beam melting. A space filling design of experiments is utilized to efficiently explore the fabrication space. Single crystals were success- fully obtained using both commercially available powders and custom melt alloys. Microstructures obtained via these exploratory experiments exhibited a continuum of columnar structures ranging from weakly textured polycrystals, near single crystal, and fully single crystalline material. Complex geometry experiments are performed to study the grain selection mechanism. We find that the grain selection mechanism is independent of the bulk scale geometry and must therefore by driven by local heat transfer and solidification dynamics. Furthermore, grain selection is shown to be driven by competing driving forces; one which prefers epitaxial growth and another which is driven by the imposed scan pattern geometry. Finally, a mechanism is proposed for the anomalous secondary orientation preference.
36 MATERIALS SCIENCE↗
Build orientation, surface roughness, and scan path influence on the microstructure, mechanical properties, and flexural fatigue behavior of Ti–6Al–4V fabricated by electron beam melting
In the present work, microstructure and fatigue behavior of Electron Beam Melted (EBM) Ti–6Al–4V have been systematically studied. Fatigue behavior was investigated using four-point bend tests of rectangular bars with internal features fabricated with different build orientations, scan paths, and surface conditions. Microstructural variations were evaluated by optical microscopy and Vickers micro-hardness indentations, both of which were found to be consistent throughout the build and within ranges reported in the literature. The fatigue performance of the EBM material was comparable to wrought Ti–6Al–4V when the loading direction was parallel to the build direction, but severely limited when loaded perpendicular to the build direction or if surface roughness defects were present. Scanning electron microscopy and interrupted fatigue tests were utilized to characterize fracture surfaces, failure mechanisms, crack initiation, and propagation behavior. Crack initiation sites in the vertically-oriented specimens were identified to be melt-related defects formed by insufficient melting.
36 MATERIALS SCIENCE↗
Fatigue crack growth resistance of a mesoscale composite microstructure Haynes 282 fabricated via electron beam melting additive manufacturing
Materials synthesis via additive manufacturing gives unprecedented control over the solidified microstructure. While a number of studies have demonstrated the ability to produce spatially varying microstructures, little work exists to understand the behavior of such “composite” materials. In this work, we utilized electron beam melting to process Ni-based superalloy Haynes 282 and produce compact tension samples with a spatially varying mesoscale structure. Fatigue crack growth experiments reveal that the crack growth rate is dependent on the degree of microstructural heterogeneity. This work demonstrates that the crack growth resistance can be tailored within a component using electron beam melting additive manufacturing.
36 MATERIALS SCIENCE↗
Influence of scan strategy on porosity and microstructure of Ti-6Al-4V fabricated by electron beam powder bed fusion
Ti-6Al-4V is of high value in biomedical, aerospace, and industrial sectors and is ideal for additive manufacturing (AM) because of its poor machinability. In electron beam powder bed fusion of Ti-6Al-4V, a raster scan is commonly used and often results in porosity that is detrimental to the fatigue strength. In this paper, we demonstrate that spot melting can significantly minimize porosity but produces a coarser microstructure compared to raster melting. Process parameters can be optimized to achieve minimal porosity with tailored microstructures. A finite element method was used to rationalize these observations.
36 MATERIALS SCIENCE↗
Microstructure and Elevated Temperature Flexure Testing of Tungsten Produced by Electron Beam Additive Manufacturing
Abstract Due to their superior high-temperature thermomechanical capabilities, sputter erosion durability, and excellent resistance to hydrogen isotopes, tungsten materials have garnered significant interest in fusion nuclear applications. However, low room-temperature ductility and complex machining strategies present significant challenges for traditional fabrication. Electron beam powder bed fusion (EB-PBF) shows promise in manufacturing pure tungsten via high thermal energy input, elevated build temperature, and a tightly controlled high-vacuum environment. This work explores the process, structure, and property relationship of pure tungsten fabricated by EB-PBF, where 99.8% relative density was achieved with reduced cracking by isolating the build substrate and optimizing the print parameter suite. Optical and electron imaging revealed that the microstructure contained equiaxed grains along the build direction, with subgrains present in all inspected grains. Flexural testing at ambient and elevated temperatures demonstrated high ductility at 900°C and flexural strength of 470 MPa at room temperature of additively manufactured tungsten.
Zhang, Haozhi↗
Dendritic microstructures observed in electron-beam deposited hafnia films
Dendritic microstructures inside hafnia dielectric coatings fabricated via electron-beam deposition are investigated. These structures are observable with different optical characterization tools, including atomic force microscopy, fluorescence microscopy, Raman microscopy, and differential interference contrast microscopy. Long-term monitoring of individual samples over a seven-year time span revealed that the dendrite-like structures evolve over time, while the hafnia material in the dendrite structure—as compared to the rest of the coating—shows a decrease in crystallinity and an increase in defect density.
Hoffman, B. N. [Univ. of Rochester, NY (United Sta↗
Probing potential energy landscapes via electron-beam-induced single atom dynamics
Structure, bonding, and chemical dynamics of reactions at surfaces and interfaces, and therefore most material properties are intrinsically tied to the energetic landscape in which each atom resides. Here, we demonstrate that a moving atom under electron beam excitation can be used to probe the energy landscape along (confined) step edges, providing information about atomic-scale potentials. In conclusion, the techniques for experimentally exploring atomic potentials holds promise for predictive atom-by-atom fabrication using electron beams.
36 MATERIALS SCIENCE↗
Implications of post-processing induced microstructural changes on the deformation and fracture response of additively manufactured Ti–6Al–4V
Ti–6Al–4V parts fabricated via electron beam melting (EBM) powder bed fusion are often subjected to hot isostatic pressing below the β-transus temperature to mitigate defects. During which the pressure aids in pore closure and the thermal exposure results in coarsening of α phase while retaining the columnar prior-β phase grain morphology present in the as-fabricated condition. The same post-processing treatment can also be carried out above β-transus temperature which is an effective way to modify both the grain morphology and the associated α textures. Here, the objective of this work is to correlate thermally induced microstructural changes to the deformation and fracture response of the EBM processed Ti–6Al–4V. To this end, we have carried out both sub-transus and super-transus heat-treatments of the as-fabricated material. The mechanical response of the as-fabricated and all heat-treated materials are characterized by in-situ tensile tests under a high-resolution digital optical microscope. This enabled us to capture large-scale panoramic images of the deforming microstructure, and overcome the trade-off between the image resolution and the field of view during in-situ experiments. The series of images captured throughout the imposed deformation are subsequently used to perform microstructure-based digital image correlation to measure microstructural-scale strains over a large area. The results of the in-situ tests together with detailed fractographic analyses are then used to elucidate how the heterogeneous deformation spanning over multiple microstructural length-scales, for example, at the scale of lamellae, colonies of lamellae and grain boundaries, affect the overall deformation and fracture response of the post-processed materials.
36 MATERIALS SCIENCE↗
The Atomic Drill Bit: Precision Controlled Atomic Fabrication of 2D Materials
The ability to deterministically fabricate nanoscale architectures with atomic precision is the central goal of nanotechnology, whereby highly localized changes in the atomic structure can be exploited to control device properties at their fundamental physical limit. Here, an automated, feedback-controlled atomic fabrication method is reported and the formation of 1D–2D heterostructures in MoS 2 is demonstrated through selective transformations along specific crystallographic orientations. The atomic-scale probe of an aberration-corrected scanning transmission electron microscope (STEM) is used, and the shape and symmetry of the scan pathway relative to the sample orientation are controlled. The focused and shaped electron beam is used to reliably create Mo 6 S 6 nanowire (MoS-NW) terminated metallic-semiconductor 1D–2D edge structures within a pristine MoS 2 monolayer with atomic precision. From these results, it is found that a triangular beam path aligned along the zig-zag sulfur terminated (ZZS) direction forms stable MoS-NW edge structures with the highest degree of fidelity without resulting in disordering of the surrounding MoS 2 monolayer. Density functional theory (DFT) calculations and ab initio molecular dynamic simulations (AIMD) are used to calculate the energetic barriers for the most stable atomic edge structures and atomic transformation pathways. These discoveries provide an automated method to improve understanding of atomic-scale transformations while opening a pathway toward more precise atomic-scale engineering of materials.
2D materials↗
Electron beam heating as a tool for fabricating lattice engineered crystals in glass [Invited]
Laser heating is well-established to impart optical functionality into glass by local modification and crystallization. In this paper, we demonstrate electron beam heating in scanning and transmission microscopes as an alternative for the local crystallization of Sb 2 S 3 in Sb-S-I glasses as a model system. Governed by different absorption physics, the electron beam expands morphological control of crystal cross section relative to laser, producing nanoscale (∼50 nm) single crystal architectures. We also report the effects of accelerating voltage and probe current and characterize the curved lattice of crystals formed in glass with electron diffraction techniques.
36 MATERIALS SCIENCE↗
Scan strategies in EBM-printed IN718 and the physics of bulk 3D microstructure development
Three-dimensional (3D) characterization provides opportunities for understanding processing-structure relationships in additively manufactured (AM) materials. Bulk samples of Inconel 718 were fabricated via electron beam melting (EBM) in order to study microstructural development as a function of energy input and beam scan strategy. TriBeam tomography of bulk Inconel 718 microstructures built under steady-state growth conditions reveals the sensitivity of microstructure formation and evolution to machine process parameters. Here, samples manufactured using a narrow range of energy input per unit build area result in varied grain morphologies and crystallographic textures. Using TRUCHAS, a thermal simulation software, the thermal history of bulk scan strategies was predicted, and combined with a calibrated microstructure-processing map to accurately predict bulk grain morphologies. The solidification parameters and the 3D measured nucleation density are used to predict the transition between columnar and equiaxed grain morphologies, providing a process map to guide AM parameter choices to locally control as-printed microstructure. A two-dimensional metric for characterizing bulk grain morphology was also found to agree well with predictions from the process map calibrated by 3D data. Combined with 3D tomography and thermal modelling, the physics of structure development were understood at a new level of detail with respect to the competing processes of grain nucleation and epitaxial growth.
36 MATERIALS SCIENCE↗
Synthesis and electrical transport properties of superconducting platinum silicide thin films and devices
Here, we evaluate the material characteristics of superconducting platinum silicide (PtSi) thin films as candidate materials for superconducting quantum information devices compatible with silicon technology. These films were synthesized using magnetron sputtering under ultrahigh vacuum conditions, followed by rapid thermal annealing. Polycrystalline PtSi films synthesized by this method have the favorable properties of superconducting critical temperature of 0.95 K and relatively long zero-temperature Ginzburg-Landau coherence length of 76 nm. We further studied coplanar microbridge devices fabricated by electron beam lithography and chlorine-free reactive ion etching, finding that the temperature-dependent critical current density follows the Ginzburg Landau depairing mechanism.
36 MATERIALS SCIENCE↗
Using Additive Manufacturing to Repair Gas Turbine Hot Section Components
Ni-based superalloys are used in the hot sections of gas turbine engines due to their excellent high temperature performance. During service the material degrades due to exposure at high temperature and mechanical loads. Hence, utility provides often inspect, service, and repair components in gas turbine engines to ensure safe operation. A major challenge, however, is that the most heat-resistant alloys are generally considered ‘non-weldable’ rendering them difficult to repair via welding operations. In these cases components are often scrapped and then replaced by parts which must be re-manufactured. This burdens utilities with additional cost and supply chain issues can result in long term outages or reduced operating limtis. In this work EPRI and ORNL investigated a proposed repair strategy for gas turbine hot section components. Hot section superalloy GTD-111 was selected as a candidate repair material system and AM material ABD-900 the repair material. Sandwich structures were fabricated via electron beam melting additive manufacturing (EBM-AM) producing tensile bars with gage sections consisting of dissimilar ABD-900 / GTD-111 / ABD-900 material. Metallography revealed that the interface exhibited no deleterious phases or processing defeats. Creep rupture experiments on heat treated material demonstrates that the emulated repair coupons exhibit creep resistance between GTD-111 and ABD-900. This study demonstrates that the proposed EBM-AM repair strategy presents a viable opportunity towards enabling AM repair of gas turbine engine components.
99 GENERAL AND MISCELLANEOUS↗