Search NASA⌕ Search

SEARCH · Search NASA

Results for “electrostatic switching”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

11 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

A magnetic diagnostic suite for the Pegasus-III experiment

Pegasus-III is an ultralow aspect ratio spherical tokamak providing a dedicated US experiment for comparative solenoid-free startup studies. A new magnetic diagnostic suite for equilibrium and low frequency (<200 kHz) magnetohydrodynamic mode analysis has been installed. These new diagnostics address the significant challenges of measuring magnetic field in a high noise environment with the majority constrained to fit in an 8 mm diagnostic gap on the high field side. Electrostatic switching noise generated by the 16 independent current feedback-controlled power supplies produces dV cm /dt ~ 1 kV/μs and volt level common mode noise on the magnetics. Immunity to this switching noise is accomplished through differential signal runs and signal processing, along with end-to-end electromagnetic interference shielding. The magnetic measurements are simultaneously digitized at 1 MHz and conditioned by precision 8 pole Butterworth filters with a corner frequency of 200 kHz to prevent aliasing down to the 16-bit level over the full passband. Ex-vessel calibrations of the B p coils were completed with a typical uncertainty of <0.5%. Stray toroidal field pickup from coil misalignment or positioning errors is corrected using a physics-based model. Comparisons of the corrected measurements to modeling agree to within 1.3% on average. This is within the 1.5% measurement uncertainty that a sensitivity analysis determined is needed for accurate fast boundary and equilibrium reconstruction.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

dynamics of organic-mineral interactions at the metal oxide-solution interface as studied via binding energetics (Final report)

This project focused on addressing longstanding fundamental and experimental uncertainties on how dissolved organic substances (DOS) interact with metal oxide surface under environmentally relevant conditions. By leveraging a custom-built real-time, in-tandem flow adsorption microcalorimetry-UV-Vis/fluorescence spectroscopy platform, we characterized the binding energetics, kinetics and mechanistic pathways driving DOS-metal oxide interactions at temporal resolution on the order of 1-5 seconds. We studied a diverse suite of model organic compounds/substances – including monocarboxylates (e.g. acetate and benzoate), di-carboxylates (oxalate and succinate), amino acids, amino-based nanparticles and natural organic matter – interacting at the mineral-water interface of structurally- and/or chemically distinct metal oxides (including SiO2, boehmite, ferrihydrite, and γ-Al2O3). Our results indicated that DOS-metal oxide interactions are governed by multi-step reaction pathways, often switching between distinct, resolvable enthalpy- and entropy-driven non-electrostatic or electrostatic configurations. To quantify these interactions, we developed and implemented an analytical workflow that integrates peak deconvolution and Monte-Carlo based error propagation to determine site-specific thermodynamic and kinetic parameters for individual binding/debinding events. In addition to resolving apparent first-order rate constants of each event, we were able to quantify associated apparent equilibrium constants as well as free energy, enthalpy and entropy contribution to the activation and subsequent progression of the binding/debinding process across compounds, compound class and metal oxide surfaces. The kinetic-thermodynamic data produced in this study captured how the interplay between oxide surface reactivity and DOS molecular structure jointly drives binding-debinding dynamics. Notably, that at pH below PZC of the oxide surface, neutral species were heavily involved in monocarboxylate binding, while anionic species drove dicarboxylate binding. Also, that among amino acids 1) positional isomers show distinctive binding characteristics to each other while enantiomers show no significant differences in binding characteristics, 2) molecules that bind via outer-sphere complexation show a larger entropic shift between binding and debinding with no impact on oxide surface while 3) inner-sphere interactions increased anion exchange capacity of the oxide surface. The new insights and data from this work has great potential for improving predictive modeling of carbon dynamics and specifically organic-mineral interactions in environmental and industrial systems.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Gate control of electron correlations towards Mott field effect transistors (MottFET)

The modulation of channel conductance in field-effect transistors (FETs) via metal-insulator-semiconductor structures has revolutionized information processing and storage. However, the limitations of silicon-based FETs in electrical switching have driven the search for new materials capable of overcoming these constraints. Electrostatic gating of competing electronic phases in a Mott material near its metal-to-insulator transition (MIT) offers the prospects of substantial modulation of the conducting electrons and electrical resistivity through small changes in band filling. While electrostatic control of the MIT has been previously reported, the advancement of Mott materials toward novel Mott-based transistors, MottFETs requires the realization of their unique physical properties in a solid-state device. In this study, we present gate control of electron correlation using a solid-state device utilizing the oxide Mott system La 1-x Sr x VO 3 as a correlated FET channel. We report on a gate resistance response that cannot be explained in a purely electrostatic framework. This behavior suggests an enhancement in effective mass and a reduction in effective carrier density as the system approaches its insulating state, consistent with theoretical predictions for Mott systems, suggesting at least 100× charge gain originating from the correlated behavior. These preliminary results pave the way toward the development of highly efficient, low-power electronic devices that could surpass the performance bottlenecks of conventional FETs by leveraging the electronic phase transitions of correlated electron systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Polarization-Controlled Structural Modulation in the Single Atomic Layer at the PbZr 0.2 Ti 0.8 O 3 /LaNiO 3 Interface

Conductivity modulation via ferroelectric polarization coupling with LaNiO 3 (LNO) is demonstrated at an epitaxial ferroelectric–LNO interface. Conductivity measurements, varying the thickness of the LNO channel, show that this phenomenon is confined to a few atomic layers at the interface. Combining in situ biasing and off-axis holography, we mapped out electrostatic potentials at the PbZr 0.2 Ti 0.8 O 3 (PZT)/LNO/SrTiO 3 (STO) heterostructure upon polarization switching. Using aberration-corrected STEM, the interfacial atomic structures were investigated for the two different PZT polarization states. Polarization in PZT induces a significant change in the in-plane O–Ni–O bond angles, with a 37° modulation in the topmost 1 or 2 LNO unit cells, driven by strain in the oxygen sublattice for the two opposite polarization directions in PZT. Both oxygen and cation sublattices exhibit strain responses exceeding 10% upon switching. This atomic-layer structural modulation highlights a mechanism for functional oxide heterostructure development, offering pathways for advancements in nonvolatile memory, sensors, and energy-efficient transistors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Establishing criteria for the transition from kinetic to fluid modeling in hollow cathode analysis

Hollow cathodes for plasma switch applications are investigated via 2D3V particle-in-cell simulations of the channel and plume region. The kinetic nature of the plasma within the channel is dependent on the thermalization rate of electrons, emitted from the insert. When Coulomb collisions occur at a much greater rate than ionization or excitation collisions, the electron energy distribution function rapidly relaxes to a Maxwellian and the plasma within the channel can be described accurately via a fluid model. In contrast, if inelastic processes are much faster than Coulomb collisions, then the electron energy distribution function in the channel exhibits a notable high-energy tail, and a kinetic treatment is required. This criterion is applied to hollow cathodes from the literature, revealing that a fluid approach is suitable for most electric propulsion applications, whereas a kinetic treatment can be more critical to accurate modeling of plasma switches.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Direct Imaging of Asymmetric Interfaces and Electrostatic Potentials inside a Hafnia–Zirconia Ferroelectric Nanocapacitor

In hafnia-based thin-film ferroelectric devices, chemical phenomena during growth and processing, such as oxygen vacancy formation and interfacial reactions, appear to strongly affect device performance. However, the correlation between the structure, chemistry, and electrical potentials at the nanoscale in these devices is not fully known, making it difficult to understand their influence on device properties. Here, we directly image the composition and electrostatic potential with nanometer resolution in the cross section of a nanocrystalline W/Hf 0.5 Zr 0.5 O 2−δ (HZO)/W ferroelectric capacitor using multimodal electron microscopy. This reveals a 1.4 nm wide tungsten suboxide interfacial layer formed at the bottom interface during fabrication, which introduces a potential dip and leads to asymmetric switching fields. Additionally, we compare the measured potentials to DFT calculations and find it is nearly 3 V lower than expected in the HZO, which appears to be caused by oxygen vacancies and a resulting negative built-in potential. In conclusion, these chemical and electrostatic details are important to characterize and tune to achieve high-performance ferroelectric devices.

Defects in solids↗
DOE OSTI2026

Substrate-Directed Dimensional and Phase Control of Peptide Assemblies on Two-Dimensional van der Waals Materials

Understanding and controlling biomolecular self-assembly on van der Waals (vdW) materials has the potential to advance hybrid bioelectronic devices by enabling precise tuning of the interface and modulation of the resulting electronic properties of the biomolecule-vdW heterostructure. However, how surface properties of vdW materials direct biomolecule assembly remains poorly understood. To fill this knowledge gap, we investigated the assembly of a peptide known to assemble into two-dimensional (2D) crystalline films on MoS 2 on three representative vdW surfaces: WS 2 , MoS 2 , and highly oriented pyrolytic graphite (HOPG). Using in situ atomic force microscopy (AFM), we find that assembly is substrate-dependent, resulting in multilayers on WS 2 , monolayers on MoS 2 , and multiple coexisting phases on HOPG. WS 2 exhibits a higher negative charge, strong long-range electrostatic interactions, and extensive hydration layering that may promote multilayer stacking. In contrast, MoS 2 has stronger short-range interactions with the peptides but much weaker long-range interactions and hydration structure, which may favor monolayer formation. Molecular dynamics simulations predict a corresponding switch from monolayer to multilayer aggregates of the adsorbed monomers, reflected in their relative mobilities. On hydrophobic HOPG, the peptides bind most strongly and remain as monomers with high surface mobility. The peptide dimers comprising the basic unit of the crystals are more compact on HOPG, which has a smaller lattice constant than WS 2 or MoS 2 , suggesting strain contributes to stabilizing multiple phases. Our results provide mechanistic insights into how surface charge and hydration structure, and the lattice structure of the substrates governs peptide assembly on vdW materials, offering a framework to rationally control the 2D peptide-vdW heterostructures.

Molecular dynamics simulations↗
DOE OSTI2026

Cosolvent-tuned interactions in ionic liquids: A vibrational and quantum-chemical study of ethylene glycol ratio effects

Ionic liquids (ILs) are attractive media for CO 2 capture but remain limited by viscosity and cost. Blending ILs with ethylene glycol (EG) is a practical route to mitigate these constraints, yet the molecular origins of cosolvent effects and their dependence on composition are not well resolved. We combine Fourier-transform infrared (FT-IR) spectroscopy with quantum-chemical (DFT) analysis to elucidate how the IL:EG molar ratio modulates intermolecular interactions and electronic structure. Computed vibrational frequencies enable mode assignment and deconvolution of overlapping bands, revealing systematic, ratio-dependent shifts and broadenings in (i) EG O–H stretching, (ii) cation and EG C–H stretchings (imidazolium C2–H, C4–H, C5–H, methyl and ethyl groups, -CH2 of EG), (iii) anion signature modes (e.g., CN motifs), and (iv) EG C–O and C–C stretchings, consistent with the redistribution of hydrogen-bonding networks. Molecular electrostatic potential (MESP) maps quantify attenuation of extreme potential regions with increasing EG, indicating progressive screening of cation–anion electrostatic interactions. Quantum Theory of Atoms in Molecules (QTAIM) identifies emergent bond critical points between EG and the IL ions, while Reduced Density Gradient–Noncovalent Interaction (RDG–NCI) analysis differentiates strong directional hydrogen bonds from dispersive contacts across compositions. Together, these results show that EG fraction controls a switch from predominantly ion–ion to mixed ion–EG coordination, altering local polarity and polarizability that underlie the observed FT-IR trends. The framework provides composition–structure–spectrum relationships that can guide rational selection of IL:EG ratios to balance favorable molecular interactions with practical performance targets in scalable CO 2 capture systems.

DAC↗
DOE OSTI2025

Imaging Bias‐Driven Domain Wall Motion With Scanning Oscillator Piezoresponse Force Microscopy

Understanding ferroelectric domain wall dynamics at the nanoscale across a broad range of timescales requires measuring domain wall position under different applied electric fields. The success of piezoresponse force microscopy (PFM) as a tool to apply local electric fields at different positions and imaging their changing position, together with the information obtained from associated switching spectroscopies has fueled numerous studies of the dynamics of ferroelectric domains to determine the impact of intrinsic parameters such as crystalline order, defects and pinning centers, as well as boundary conditions such as environment. However, the investigation of sub-coercive reversible domain wall vibrational modes requires the development of new tools that enable visualizing domain wall motion under varying applied fields with high temporal and spatial resolution while also accounting for spurious electrostatic effects. Here, scanning oscillator piezoresponse force microscopy extends the investigation of domain wall dynamics to new regimes, providing direct visualization of domain wall position as a function of an external electric field that varies in time and location. In conclusion, this enables studying the energetics of field-driven ferroelectric domain wall motion, which is shown to obey a thermally activated flow regime in the millisecond timescale.

Piezoresponse Force Microscopy↗
DOE OSTI2024

Nonlinear Poisson–Boltzmann solutions for charged parallel plates: When opposite charges repel

I present an exact solution of the Poisson–Boltzmann equation for two parallel plates and discuss the solution properties. I discuss in more detail plates with opposite charges: In this case, there are two critical separations, L c,1 < L c,2 . For separations less than L c,1 , the force between plates is repulsive. It switches to attractive at L c,1 , but with the electric potential having the same sign on both plates. For L > L c,2 , the force remains attractive, and the potential at the plates has the same sign as the charge on each plate. I also describe charge regulation, determined by pK a , and provide formulas for both the critical distance where oppositely charged plates repel and their charging process. Finally, the implications of these results for the nanoparticle assembly, as driven by electrostatic interactions, are also discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Reversible Ferroelectric Polarization Modulation of Chiral Molecular Ferroelectrics by Circularly Polarized Light

Abstract The optical modulation of ferroelectric polarization constitutes a transformative, non‐contact strategy for the precise manipulation of ferroelectric properties, heralding advancements in optically stimulated ferroelectric devices. Despite its potential, progress in this domain is constrained by material limitations and the intricate nature of the underlying mechanisms. Recent studies have achieved efficient regulation of ferroelectric polarization and thermal conductivity in chiral ferroelectric thin films through the application of left‐ and right‐handed circularly polarized light (LCP and RCP). Differential absorption of circularly polarized light (CPL) induces nonequilibrium carrier dynamics, generating distinctive interfacial electrostatic fields that enable precise control of ultrathin ferroelectric films. For (R)‐BINOL−DIPASi and (S)‐BINOL−DIPASi (C 26 H 26 O 2 Si), polarization changes surpass 23%, exhibiting opposite response under LCP and RCP excitation. In R chiral films, remnant polarization decreases from 1.05 µC cm − 2 under LCP to 0.85 µC cm − 2 under RCP, whereas in S chiral films, polarization increases from 0.85 µC cm − 2 under LCP to 0.98 µC cm − 2 under RCP. This reversible modulation facilitates reliable switching between ON and OFF states, presenting the potential of chiral ferroelectric materials for flexible, high‐speed integrated photonic sensor technologies.

Chemistry↗