SEARCH · Search NASA

Results for “end block dynamics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

NASA NTRS1993

Synoptic/planetary-scale interactions and blocking over the North Atlantic Ocean

The central theme of this project has been the diagnosis of blocking anticyclogenesis and the corresponding interactions with synoptic-scale circulations. To that end an extensive investigation of the dynamics and energetics of a major blocking anticyclone and two upstream cyclones, all of which occurred over the North Atlantic Ocean and the United States in January 1979, was undertaken. Data for the study were provided by Goddard Laboratory for Atmospheres (GLA) 4 LAT by 5 LON FGGE analyses. The methodology has primarily focused on the diagnosis of circulation forcing mechanisms using the modified forms (referred to as the extended forms) of the height tendency and Zwack-Okossi equations developed by our research group. Calculations use routine second-order finite differencing with boundary layer fraction and sensible heating and latent heat release represented as parameterized quantities. Of particular interest are the latent heat release estimates, which combine convectional parameterized values with estimates derived from satellite IR data. The latter were obtained using an algorithm derived by Dr. Franklin R. Robertson of NASA's Marshall Space Flight Center. Results are contained in project reports, theses and publications identified in previous review summaries and reports, and publications listed at the end of this summary. Significant accomplishments in the past year are presented.

Smith, Phillip J.↗

NASA NTRS2012

NASA Tech Briefs, July 2012

Topics covered include: Instrument Suite for Vertical Characterization of the Ionosphere-Thermosphere System; Terahertz Radiation Heterodyne Detector Using Two-Dimensional Electron Gas in a GaN Heterostructure; Pattern Recognition Algorithm for High-Sensitivity Odorant Detection in Unknown Environments; Determining Performance Acceptability of Electrochemical Oxygen Sensors; Versatile Controller for Infrared Lamp and Heater Arrays; High-Speed Scanning Interferometer Using CMOS Image Sensor and FPGA Based on Multifrequency Phase-Tracking Detection; Ultra-Low-Power MEMS Selective Gas Sensors; Compact Receiver Front Ends for Submillimeter-Wave Applications; Dynamically Reconfigurable Systolic Array Accelerator; Blocking Losses With a Photon Counter; Motion-Capture-Enabled Software for Gestural Control of 3D Mod; Orbit Software Suite; CoNNeCT Baseband Processor Module Boot Code SoftWare (BCSW); Trajectory Software With Upper Atmosphere Model; ALSSAT Version 6.0; Employing a Grinding Technology to Assess the Microbial Density for Encapsulated Organisms; Demonstration of Minimally Machined Honeycomb Silicon Carbide Mirrors; Polyimide Aerogel Thin Films; Nanoengineered Thermal Materials Based on Carbon Nanotube Array Composites; Composite Laminate With Coefficient of Thermal Expansion Matching D263 Glass; Robust Tensioned Kevlar Suspension Design; Focal Plane Alignment Utilizing Optical CMM; Purifying, Separating, and Concentrating Cells From a Sample Low in Biomass; Virtual Ultrasound Guidance for Inexperienced Operators; Beat-to-Beat Blood Pressure Monitor; Non-Contact Conductivity Measurement for Automated Sample Processing Systems; An MSK Radar Waveform; Telescope Alignment From Sparsely Sampled Wavefront Measurements Over Pupil Subapertures; Method to Remove Particulate Matter from Dusty Gases at Low Pressures; Terahertz Quantum Cascade Laser With Efficient Coupling and Beam Profile; Measurement Via Optical Near-Nulling and Subaperture Stitching; 885-nm Pumped Ceramic Nd:YAG Master Oscillator Power Amplifier Laser System; Airborne Hyperspectral Imaging System; Heat Shield Employing Cured Thermal Protection Material Blocks Bonded in a Large-Cell Honeycomb Matrix; and Asymmetric Supercapacitor for Long-Duration Power Storage.

Source record↗

NASA NTRSDate not supplied

Harnessing the Digital Transformation for Development of Electrified Aircraft Propulsion Control Systems

Hybrid electric aircraft propulsion is an emerging technology that presents a variety of potential benefits along with technical integration challenges. Developing these new propulsion architectures with their complex control systems, and ultimately proving their benefit, is a multistep process that goes from concept, to analysis, to dynamic simulation, to hardware in the loop testing, to full scale testing and beyond. This effort is being revolutionized and indeed enabled by new digital tools that support the increasing technology readiness level throughout the maturation process. NASA has developed and made available a suite of digital tools that ease the path from concept to implementation. The three packages are the Toolbox for the Modeling and Analysis of Thermodynamic Systems (T-MATS), the Electrical Modeling and Thermal Analysis Toolbox (EMTAT), and the Thermal Systems Analysis Toolbox (TSAT). These tools are interactive, complementary, and compatible with each other. T-MATS is a modular thermodynamic modeling framework designed for creating custom component level models of jet engines. EMTAT is a modeling framework used to simulate a variety of power electronic devices, using both physics-based and power flow calculations. TSAT is a framework for modeling and analysis of dynamic heat transfer. These packages all consist of graphical, drag-and-drop, parameterizable building blocks representing various components of the system to be modeled, e.g., compressors, turbines, motors, energy storage devices, etc. They are designed to enable the user to model and simulate the end-to-end dynamic operation of a hybrid powertrain at the timescale of the turbomachinery, capturing mechanical, electrical, and thermal interactions. This paper will describe through multiple examples how these tools have been used successfully in several of the early stages of hybrid electric propulsion system development, from the initial system modeling to real-time interactive pilot-in-the-loop simulation to physical hardware-in-the-loop testing, each step bringing the technology closer to fruition.

Hybrid electric propulsion↗

NASA NTRSDate not supplied

Harnessing the Digital Transformation for Development of Hybrid Electric Aircraft Propulsion Control Systems

Electrified Propulsion↗

NASA NTRS2023

Harnessing the Digital Transformation for Development of Electrified Aircraft Propulsion Control Systems

Hybrid electric aircraft propulsion is an emerging technology that presents a variety of potential benefits along with technical integration challenges. Developing these new propulsion architectures with their complex control systems, and ultimately proving their benefit, is a multistep process. This process includes concept development and analysis, dynamic simulation, hardware-in-the-loop testing, full-scale testing, and so on. This effort is being revolutionized and indeed enabled by new digital tools that support increasing the technology readiness level throughout the maturation process. As part of this Digital Transformation, NASA has developed a suite of publicly available digital tools that facilitate the path from concept to implementation. This paper describes the NASA-developed tools and puts them in the context of control system development for hybrid electric aircraft propulsion. The three MATLAB®-based software packages are the Toolbox for the Modeling and Analysis of Thermodynamic Systems (T-MATS), the Electrical Modeling and Thermal Analysis Toolbox (EMTAT), and the Thermal Systems Analysis Toolbox (TSAT). These tools are interactive, complementary, and compatible with each other. T-MATS is a modular thermodynamic modeling framework designed for creating custom component level models of jet engines. EMTAT is a modeling framework used to simulate a variety of power electronic devices, using both physics-based and power flow calculations. TSAT is a framework for modeling and analysis of dynamic heat transfer. These packages all consist of graphical, drag-and-drop, parameterizable building blocks representing various components of the system to be modeled, e.g., compressors, turbines, motors, energy storage devices, etc. They are designed to enable the user to model and simulate the end-to-end dynamic operation of a hybrid electric gas turbine engine powertrain at the timescale of the turbomachinery, capturing mechanical, electrical, and thermal interactions. This paper demonstrates through multiple examples how these tools have been used successfully in a variety of applications, including several of the early stages of hybrid electric gas turbine engine propulsion system development, from the initial system modeling to real-time interactive pilot-in-the-loop simulation to physical hardware-in-the-loop testing, each step bringing the technology closer to fruition.

hybrid electric propulsion↗

NASA NTRS2025

Near-Field Separation and Dynamics Analysis of NASA's Space Launch System Block-1 and Block-1B Secondary Payloads

The NASA Space Launch System (SLS) Program Block-1 and Block-1B missions are expected to carry a number of CubeSat secondary payloads (SPL) to space, where they will be ejected from internal SLS structures to begin their own missions. This near-field ejection process must be closely evaluated to ensure that no SPL contacts the SLS structures, as contacts could result in SPL component damage, mission loss, or aberrant SPL trajectories. To this end, multiple SPL ejection events were analyzed for both Block-1 and Block-1B mission configurations using CLVTOPS, a NASA Marshall Space Flight Center (MSFC) developed multi-body dynamics, proximity analysis, and visualization toolchain. This paper details the SPL-to-SLS clearance assessment process, with a focus on simulation setup and results as well as SPL design requirement analysis. Relevant CLVTOPS, statistics, and mission backgrounds are covered; important constraints, difficulties, and assumptions are also documented. Furthermore, the importance of SPL housing geometry on near-field vehicle clearance is highlighted, and examples are shown.

Jared T Rucker↗

NASA NTRS1993

Control structural interaction testbed: A model for multiple flexible body verification

Conventional end-to-end ground tests for verification of control system performance become increasingly complicated with the development of large, multiple flexible body spacecraft structures. The expense of accurately reproducing the on-orbit dynamic environment and the attendant difficulties in reducing and accounting for ground test effects limits the value of these tests. TRW has developed a building block approach whereby a combination of analysis, simulation, and test has replaced end-to-end performance verification by ground test. Tests are performed at the component, subsystem, and system level on engineering testbeds. These tests are aimed at authenticating models to be used in end-to-end performance verification simulations: component and subassembly engineering tests and analyses establish models and critical parameters, unit level engineering and acceptance tests refine models, and subsystem level tests confirm the models' overall behavior. The Precision Control of Agile Spacecraft (PCAS) project has developed a control structural interaction testbed with a multibody flexible structure to investigate new methods of precision control. This testbed is a model for TRW's approach to verifying control system performance. This approach has several advantages: (1) no allocation for test measurement errors is required, increasing flight hardware design allocations; (2) the approach permits greater latitude in investigating off-nominal conditions and parametric sensitivities; and (3) the simulation approach is cost effective, because the investment is in understanding the root behavior of the flight hardware and not in the ground test equipment and environment.

Chory, M. A.↗

NASA NTRSDate not supplied

Near-Field Separation Analysis of SLS Block-1 and Block-1B Secondary Payloads

Jared Rucker↗

NASA NTRS1990

Experimental and analytical study of close-coupled ventral nozzles for ASTOVL aircraft

Flow in a generic ventral nozzle system was studied experimentally and analytically with a block version of the PARC3D computational fluid dynamics program (a full Navier-Stokes equation solver) in order to evaluate the program's ability to predict system performance and internal flow patterns. For the experimental work a one-third-size model tailpipe with a single large rectangular ventral nozzle mounted normal to the tailpipe axis was tested with unheated air at steady-state pressure ratios up to 4.0. The end of the tailpipe was closed to simulate a blocked exhaust nozzle. Measurements showed about 5 1/2 percent flow-turning loss, reasonable nozzle performance coefficients, and a significant aftward axial component of thrust due to flow turning loss, reasonable nozzle performance coefficients, and a significant aftward axial component of thrust due to flow turning more than 90 deg. Flow behavior into and through the ventral duct is discussed and illustrated with paint streak flow visualization photographs. For the analytical work the same ventral system configuration was modeled with two computational grids to evaluate the effect of grid density. Both grids gave good results. The finer-grid solution produced more detailed flow patterns and predicted performance parameters, such as thrust and discharge coefficient, within 1 percent of the measured values. PARC3D flow visualization images are shown for comparison with the paint streak photographs. Modeling and computational issues encountered in the analytical work are discussed.

Mcardle, Jack G.↗

NASA NTRS2014

Clearance Analysis of Node 3 Aft CBM to the Stowed FGB Solar Array

In early 2011, the ISS Vehicle Configuration Office began considering the relocation of the Permanent Multipurpose Module (PMM) to the aft facing Common Berthing Mechanism (CBM) on Node 3 to open a berthing location for visiting vehicles on the Node 1 nadir CBM. In this position, computer-aided design (CAD) models indicated that the aft end of the PMM would be only a few inches from the stowed Functional Cargo Block (FGB) port solar array. To validate the CAD model clearance analysis, in the late summer of 2011 the Image Science and Analysis Group (ISAG) was asked to determine the true geometric relationship between the on-orbit aft facing Node 3 CBM and the FGB port solar array. The desired measurements could be computed easily by photogrammetric analysis if current imagery of the ISS hardware were obtained. Beginning in the fall of 2011, ISAG used the Dynamic Onboard Ubiquitous Graphics (DOUG) program to design a way to acquire imagery of the aft face of Node 3, the aft end-cone of Node 1, the port side of pressurized mating adapter 1 (PMA1), and the port side of the FGB out to the tip of the port solar array using cameras on the Space Station Remote Manipulator System (SSRMS). This was complicated by the need to thread the SSRMS under the truss, past Node 3 and the Cupola, and into the space between the aft side of Node 3 and the FGB solar array to acquire more than 100 images from multiple positions. To minimize the number of SSRMS movements, the Special Purpose Dexterous Manipulator (SPDM) would be attached to the SSRMS. This would make it possible to park the SPDM in one position and acquire multiple images by changing the viewing orientation of the SPDM body cameras using the pan/tilt units on which the cameras are mounted. Using this implementation concept, ISAG identified four SSRMS/SPDM positions from which all of the needed imagery could be acquired. Based on a photogrammetric simulation, it was estimated that the location of the FGB solar array could be measured within an accuracy of about 1 in. in each axis relative to the ISS Analysis Coordinate System (ISSACS). In October 2011, a proposed image-acquisition plan was drafted by ISAG and released for review. The ISS Robotics flight control team (ROBO) proposed minor changes to SPDM positions 1 and 4 to meet ISS proximity requirements. The updated image acquisition plan and draft chit were presented to and approved by the Systems Working Group (SWG) November 18 and were sent to the Vehicle Configuration Board (VCB) in early December 2011. Working with ROBO on 3 successive days (February 21, 22, and 23), ISAG collected 161 images of the ISS. Approximately 40 images were collected from each of the four different SSRMS/SPDM positions, with each set mapping the region from the Node 3 end cone, across Node 1, along the forward port side portion of the FGB, and out the port side FGB solar arrays. From this imagery, the best 80 images were selected for use in the analysis. The images were radiometrically enhanced to improve color and contrast and loaded into the FotoG analysis software along with the camera parameters and control data, which consisted of the coordinates for 54 handrail attachment bolts on the aft face of Node 3, in the ISSACS coordinate system. The results of this analysis produced the measured coordinates of 116 points distributed across the face of the FGB solar array panels (see figure 3) along with propagated uncertainty estimates in each coordinate axis. These results were sent to the ISS Vehicle Configuration Office, which sent them to the Configuration Analysis Modeling and Mass Properties (CAMMP) team for comparison with the Russian-provided CAD model for the retracted FGB solar arrays. The CAMMP analysis unexpectedly showed that the measured location of the port FGB solar array was up to 41-in. further outboard than the design and was slightly twisted about its rotational axis. The unexpected comparison results produced some initial concern regarding the accuracy of the photogrammetric measurements. To verify the measured results, ISAG personnel conducted a second analysis using just the imagery of the solar arrays in an arbitrary coordinate system defined by the three corner points of the inboard-most panel, with the design distance between points A1 and A10 as the only scale. The new measurements agreed with the original results to within less than 1 in. RMS in each axis, confirming the original solar array measurements. ISAG produced a final report for the ISS Vehicle Configuration Office documenting an apparent anomaly in the retracted configuration of the port FGB solar arrays. A copy of the measurement report was translated and sent to the Russian Space Agency. During a Vehicle Integrated Performance and Resources (VIPeR) teleconference September 24, 2012, the Russians acknowledged receipt of a translated copy of the ISAG report. The Russian representative stated that the head of the solar array design team claimed that the measured configuration was impossible unless the structure was physically broken. The Russians acknowledged that they had no expertise in photogrammetry, so the analysis technique employed was a "black box" to them, and they did not know how to use the ISAG results. They asked for a single image in which the overextension of the port solar array could be obviously seen. On November 10, 2012, during a face-to-face meeting with their Russian counterparts at JSC, ISAG presented nadir-view imagery of the FGB acquired during Space Shuttle rendezvous. Using the known width of the pressurized portion of the FGB as a scale, this analysis clearly showed that the port FGB solar array was extended outboard further than the Russian design for the retracted solar array.

Liddle, Donn↗

NASA NTRS1990

Flow studies in close-coupled ventral nozzles for STOVL aircraft

Flow in a generic ventral nozzle system was studied experimentally and analytically with the PARC3D computational fluid dynamics program in order to evaluate the program's ability to predict system performance and internal flow patterns. A generic model of a tailpipe with a rectangular ventral nozzle, about 1/3 of full size, was tested with unheated air at steady state pressure ratios up to 4.0. The end of the tailpipe was closed to simulate a blocked exhaust nozzle. Flow behavior into and through the ventral duct is discussed and illustrated with paint streak flow visualization photographs. PARC3D graphic images are shown for comparison with the experimental photographs. The program successfully predicted internal flow patterns; it also computed thrust and discharge coefficients within 1 pct. of measured values.

Mcardle, Jack G.↗

NASA NTRS1989

Parallel processing of real-time dynamic systems simulation on OSCAR (Optimally SCheduled Advanced multiprocessoR)

Parallel processing of real-time dynamic systems simulation on a multiprocessor system named OSCAR is presented. In the simulation of dynamic systems, generally, the same calculation are repeated every time step. However, we cannot apply to Do-all or the Do-across techniques for parallel processing of the simulation since there exist data dependencies from the end of an iteration to the beginning of the next iteration and furthermore data-input and data-output are required every sampling time period. Therefore, parallelism inside the calculation required for a single time step, or a large basic block which consists of arithmetic assignment statements, must be used. In the proposed method, near fine grain tasks, each of which consists of one or more floating point operations, are generated to extract the parallelism from the calculation and assigned to processors by using optimal static scheduling at compile time in order to reduce large run time overhead caused by the use of near fine grain tasks. The practicality of the scheme is demonstrated on OSCAR (Optimally SCheduled Advanced multiprocessoR) which has been developed to extract advantageous features of static scheduling algorithms to the maximum extent.

Kasahara, Hironori↗

NASA NTRS2021

Fast Near-Optimal Heterogeneous Task Allocation via Flow Decomposition

Multi-robot systems are uniquely well-suited to perform complex tasks such as patrolling and tracking, infor- mation gathering, and pick-up and delivery problems, offering significantly higher performance than single-robot systems. A fundamental building block in most multi-robot systems is dynamic task allocation: assigning robots to tasks (e.g., patrolling an area, or servicing a transportation request) as they appear based on the robots’ states to maximize reward. In many practical situations, the allocation must account for potentially heteroge- neous capabilities (e.g., availability of appropriate sensors or actuators) to ensure the feasibility of execution, and exploit predictive information concerning the likelihood of future tasks to promote a higher reward over a long time horizon. To this end, we present an efficient algorithm for predictive heterogeneous task- allocation achieving an approximation factor of at least 1/2 of the optimal reward. Our approach demonstrates that the problem can be decomposed into several homogeneous subproblems that can be solved efficiently using min-cost flow. Through simulation experiments, we show that our algorithm is faster by several orders of magnitude than a MILP-based approach.

Pavone, Marco↗

NASA NTRSDate not supplied

Thermoplastic Composite Lunar Tower Truss Structure: Design Development and Verification Plans

The National Aeronautics and Space Administration (NASA) Space Technology and Mission Directorate (STMD) is advancing thermoplastic composite (TPC) technologies for exploration missions. The Technology Development for Exploration Applications (TDEA) project goals are to develop and mature TPC materials, designs, analyses tools and techniques, and mature manufacturing processes. This includes development of manufacturing and joining approaches relevant to space environments. To these ends TDEA endeavors toward demonstrating a TPC truss structure for a lunar tower configuration. The design, predicated on robotic assembly, uses open section truss elements fused to a joint splice plate, without a structural adhesive. This presentation details the TDEA lunar truss structure design development approach including design heritage, the requirements established, the mechanical design and analyses, and thermal analyses demonstrating structural requirements conformance, as well as planned building block verification efforts either underway or planned. The mechanical analyses show the most severe environment is a moon-quake the truss dynamic responses. The thermal analyses show the extreme cold for on-orbit welding, the window for less severe on-orbit welding, as well as the large thermal gradients on the truss. The building block approach shown includes ultrasonic welding and lap shear coupon testing on various truss element thicknesses and layups. Knockdown factor determinations due to lunar dust contamination (simulated) and effects of welding in a vacuum are presented. The most highly loaded truss joint configuration sub-element verification test matrix is outlined. Lastly, plans to build, inspect, and test a 2-bay truss representative unit cell that is 1.5 meters by 1.5 meters by 3.0 meters tall are detailed.

Lunar Tower↗

NASA NTRS2004

NASA Tech Briefs, June 2004

Topics covered include: COTS MEMS Flow-Measurement Probes; Measurement of an Evaporating Drop on a Reflective Substrate; Airplane Ice Detector Based on a Microwave Transmission Line; Microwave/Sonic Apparatus Measures Flow and Density in Pipe; Reducing Errors by Use of Redundancy in Gravity Measurements; Membrane-Based Water Evaporator for a Space Suit; Compact Microscope Imaging System with Intelligent Controls; Chirped-Superlattice, Blocked-Intersubband QWIP; Charge-Dissipative Electrical Cables; Deep-Sea Video Cameras Without Pressure Housings; RFID and Memory Devices Fabricated Integrally on Substrates; Analyzing Dynamics of Cooperating Spacecraft; Spacecraft Attitude Maneuver Planning Using Genetic Algorithms; Forensic Analysis of Compromised Computers; Document Concurrence System; Managing an Archive of Images; MPT Prediction of Aircraft-Engine Fan Noise; Improving Control of Two Motor Controllers; Electro-deionization Using Micro-separated Bipolar Membranes; Safer Electrolytes for Lithium-Ion Cells; Rotating Reverse-Osmosis for Water Purification; Making Precise Resonators for Mesoscale Vibratory Gyroscopes; Robotic End Effectors for Hard-Rock Climbing; Improved Nutation Damper for a Spin-Stabilized Spacecraft; Exhaust Nozzle for a Multitube Detonative Combustion Engine; Arc-Second Pointer for Balloon-Borne Astronomical Instrument; Compact, Automated Centrifugal Slide-Staining System; Two-Armed, Mobile, Sensate Research Robot; Compensating for Effects of Humidity on Electronic Noses; Brush/Fin Thermal Interfaces; Multispectral Scanner for Monitoring Plants; Coding for Communication Channels with Dead-Time Constraints; System for Better Spacing of Airplanes En Route; Algorithm for Training a Recurrent Multilayer Perceptron; Orbiter Interface Unit and Early Communication System; White-Light Nulling Interferometers for Detecting Planets; and Development of Methodology for Programming Autonomous Agents.

Source record↗

NASA NTRS2009

Multimodal Friction Ignition Tester

The multimodal friction ignition tester (MFIT) is a testbed for experiments on the thermal and mechanical effects of friction on material specimens in pressurized, oxygen-rich atmospheres. In simplest terms, a test involves recording sensory data while rubbing two specimens against each other at a controlled normal force, with either a random stroke or a sinusoidal stroke having controlled amplitude and frequency. The term multimodal in the full name of the apparatus refers to a capability for imposing any combination of widely ranging values of the atmospheric pressure, atmospheric oxygen content, stroke length, stroke frequency, and normal force. The MFIT was designed especially for studying the tendency toward heating and combustion of nonmetallic composite materials and the fretting of metals subjected to dynamic (vibrational) friction forces in the presence of liquid oxygen or pressurized gaseous oxygen test conditions approximating conditions expected to be encountered in proposed composite material oxygen tanks aboard aircraft and spacecraft in flight. The MFIT includes a stainless-steel pressure vessel capable of retaining the required test atmosphere. Mounted atop the vessel is a pneumatic cylinder containing a piston for exerting the specified normal force between the two specimens. Through a shaft seal, the piston shaft extends downward into the vessel. One of the specimens is mounted on a block, denoted the pressure block, at the lower end of the piston shaft. This specimen is pressed down against the other specimen, which is mounted in a recess in another block, denoted the slip block, that can be moved horizontally but not vertically. The slip block is driven in reciprocating horizontal motion by an electrodynamic vibration exciter outside the pressure vessel. The armature of the electrodynamic exciter is connected to the slip block via a horizontal shaft that extends into the pressure vessel via a second shaft seal. The reciprocating horizontal motion can be chosen to be random with a flat spectrum over the frequency range of 10 Hz to 1 kHz, or to be sinusoidal at any peak-to-peak amplitude up to 0.8 in. (.2 cm) and fixed or varying frequency up to 1 kHz. The temperatures of the specimen and of the vessel are measured by thermocouples. A digital video camera mounted outside the pressure vessel is aimed into the vessel through a sapphire window, with its focus fixed on the interface between the two specimens. A position transducer monitors the displacement of the pneumatic-cylinder shaft. The pressure in the vessel is also monitored. During a test, the output of the video camera, the temperatures, and the pneumatic-shaft displacement are monitored and recorded. The test is continued for a predetermined amount of time (typically, 10 minutes) or until either (1) the output of the position transducer shows a sudden change indicative of degradation of either or both specimens, (2) ignition or another significant reaction is observed, or (3) pressure in the vessel increases beyond a pre-set level that triggers an automatic shutdown.

Davis, Eddie↗

NASA NTRS1993

CFD simulation of coaxial injectors

The development of improved performance models for the Space Shuttle Main Engine (SSME) is an important, ongoing program at NASA MSFC. These models allow prediction of overall system performance, as well as analysis of run-time anomalies which might adversely affect engine performance or safety. Due to the complexity of the flow fields associated with the SSME, NASA has increasingly turned to Computational Fluid Dynamics (CFD) techniques as modeling tools. An important component of the SSME system is the fuel preburner, which consists of a cylindrical chamber with a plate containing 264 coaxial injector elements at one end. A fuel rich mixture of gaseous hydrogen and liquid oxygen is injected and combusted in the chamber. This process preheats the hydrogen fuel before it enters the main combustion chamber, powers the hydrogen turbo-pump, and provides a heat dump for nozzle cooling. Issues of interest include the temperature and pressure fields at the turbine inlet and the thermal compatibility between the preburner chamber and injector plate. Performance anomalies can occur due to incomplete combustion, blocked injector ports, etc. The performance model should include the capability to simulate the effects of these anomalies. The current approach to the numerical simulation of the SSME fuel preburner flow field is to use a global model based on the MSFC sponsored FNDS code. This code does not have the capabilities of modeling several aspects of the problem such as detailed modeling of the coaxial injectors. Therefore, an effort has been initiated to develop a detailed simulation of the preburner coaxial injectors and provide gas phase boundary conditions just downstream of the injector face as input to the FDNS code. This simulation should include three-dimensional geometric effects such as proximity of injectors to baffles and chamber walls and interaction between injectors. This report describes an investigation into the numerical simulation of GH2/LOX coaxial injectors. The following sections will discuss the physical aspects of injectors, the CFD code employed, and preliminary results of a simulation of a single coaxial injector for which experimental data is available. It is hoped that this work will lay the foundation for the development of a unique and useful tool to support the SSME program.

Landrum, D. Brian↗

NASA NTRS1995

Geologic investigations of a 'slip gap' in the surficial ruptures of the 1992 Landers earthquake, southern California

A 3-km-long gap in the dextral surficial rupture of the 1992 M(sub W) = 7.3 Landers earthquake occurs at the north end of a major fault stepover between the Johnson Valley and Homestead Valley faults. This gap is situated along a segment of the Landers rupture that has been modeled geophysically as having a deficit in average slip at depth. To better evaluate the nature of the slip gap, we document in detail the character and distribution of surficial rupture within it. Along the gap, is a northwest trending thrust fault rupture with an average of less than 1 m of northeast directed reverse-slip and nearly no oblique right slip. We interpret this rupture to be limited to the shallow crust of the northern end of the stepover and to have been the secondary result of dextral shear, rather than a mechanism of rigid-block slip-transfer from the Landers-Kickapoo fault. A zone of en echelon extensional ruptures also occurs along the slip gap, which we interpret as the secondary result of diffuse dextral shear that accommodated less than 0.5 m of west-northwest extension. These secondary ruptures represent a discontinuity in the surficial dextral ruptre of the Landers earthquake, which we propose resulted from the lack of a mature fault connection between the Johnson Valley and Homestead Valley faults. The rupture pattern of the slip gap implies a significant deficit in net surficial slip, which compares favorably with some geophysical models. Aspects of this rupture pattern also suggest a temporal sequence of rupture that compares favorably with geophysical interpretations of the dynamic rupture propagation.

Spotila, James A.↗