Search NASA⌕ Search

SEARCH · Search NASA

Results for “exposed kernels”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Exposed Kernel Heating Tests

Presentation on cracked AGR-2 TRISO particles and AGR-3/4 compacts subjected to FACS tests with and without prior reirradiation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Preliminary results from the first round of post-irradiation heating tests of fuel compacts from the US AGR-3/4 irradiation

Three post-irradiation heating tests of fuel compacts from the US AGR-3/4 irradiation experiment. In addition to TRISO-coated driver fuel, each compact contained 20 particles with UCO fuel kernels coated only in pyrocarbon to simulate exposed kernels. Tests at 1600/1700°C, 1400°C, and 1200°C were performed to measure fission product releases as a function of time and temperature. Silver releases were highest in the 1200°C test, supporting the observation that silver release rates are highest in the temperature range of 1100-1300°C. Except for Ag-110m (which was released in multiple particle equivalents) releases of Cs, Kr, Eu, and Sr were all less than one particle inventory per compact. This suggests that exposed kernels retain little Cs and Kr after irradiation. Despite these low releases, compared to tests of compacts with no exposed kernels, the Cs and Kr releases were noticeably higher, and at 1600°C the exposed kernels contributed noticeably more Eu and Sr than in AGR-1 compacts with no exposed kernels. These data can be used to make inferences on retention of fission products in exposed kernels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Post-irradiation Heating Tests of As-Irradiated AGR-3/4 TRISO Fuel Compacts

Four post-irradiation heating tests of fuel compacts from the U.S. Advanced Gas Reactor (AGR)-3/4 irradiation experiment were completed. In addition to tristructural isotropic (TRISO)-coated driver fuel, each compact contained designed-to-fail (DTF) particles with fuel kernels coated only in pyrocarbon so as to simulate exposed kernels. Tests at 1600/1700°C, 1400°C, and 1200°C were performed to measure fission product release as a function of time and temperature. Silver release was highest in the 1200°C test, supporting the observation that silver release rates are highest in the 1100–1300°C range. Compared to tests of AGR-1 compacts with no exposed kernels, the Cs-134 and Kr-85 releases were noticeably higher in AGR-3/4. The exposed kernels’ contributions to Eu and Sr release are inconclusive, due to the difficulty in distinguishing among the combined effects of higher irradiation temperatures in these particular AGR-3/4 compacts, the presence of the DTF particles, and the Fuel Accident Condition Simulator (FACS) test temperatures. These data can be used to make inferences about fission product retention in exposed kernels as a function of time and temperature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AGR-5/6/7 Final Release-to-Birth Ratio Data Analysis

AGR-5/6/7 is the last of a series of Advanced Gas Reactor (AGR) experiments conducted in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) in support of development and qualification of tristructural isotropic (TRISO) low-enriched fuel for use in the high-temperature gas cooled reactor (HTGR). AGR configuration and irradiation conditions are based on prismatic HTGR technology that is distinguished primarily through the use of helium coolant, a low-power-density ceramic core capable of withstanding very high temperatures, and TRISO-coated particle fuel. The AGR tests provide valuable irradiation-performance data to support fuel process development, qualify fuel for normal operation and accident conditions, and support development and validation of fuel performance and fission-product (FP) transport models and codes. Each AGR test consists of multiple independently controlled and monitored capsules containing fuel compacts placed in a graphite cylinder shrouded by a steel shell. Release-to-birth ratios (R/B) for fission-gas isotopes released from each capsule are calculated from release rates, measured by germanium detectors in the Fission Product Monitoring System (FPMS) installed downstream from each capsule, and birth rates calculated using numerical models of FG generation. The R/Bs are a critical measure of the ability of the fuel kernel, the particle coating layers, and the compact matrix to retain fission-gas atoms, preventing their release into the sweep-gas flow, and the impact of initially defective particles and/or particle-coating failures that occur during irradiation. For fission-gas isotopes, particle failure is defined as failure of all coating layers, allowing gaseous fission atoms to escape from a particle. During the first five cycles (162B ? 165A), R/Bs were stable in the 10-8?10-6 range, and no in-pile particle failures were observed, based on the gross gamma counts. The maximum R/B value of around 2 ? 10-6 for Kr-85m resulted from the presence of as-fabricated exposed kernels (based on the high exposed kernel fraction), the dispersed uranium, and high fuel particle temperatures in Capsule 1. Comparison of capsule-measured R/Bs from these early cycles to predictions using the previously developed AGR R/B model demonstrated FG release from the AGR-5/6/7 TRISO fuel was comparable to that of previous experiments. In addition, the Kr-85m R/B per-exposed-kernel values are comparable to R/B values obtained in AGR-3/4 irradiation experiment and four irradiation experiments performed during 1980s: (1) HRB-17/18, (2) COMEDIE-BD1, (3) HFR B1, and (4) HRB-21. In contrast, all measured R/B values are lower than predictions by the commonly used Richards and German models, which are intentionally conservative. A large number of in-pile particle failures occurred in Capsule 1 by the end of Cycle 166A. During the final four cycles (166A ? 168A), apparent damage to the Capsule 1 gas line appeared to cause FG leakage from that capsule into the other four capsules, resulting in an increase in fission gas (FG) detected in the effluent for all capsules. Isolation of the Capsule 1 gas line during the last three cycles also prevented measurement of its FG release. Thus, R/Bs in all capsules after Cycle 166A are highly uncertain because of undefined amount of leakage from Capsule 1, especially for long-lived isotopes. A few hundred in-pile particle failures were estimated for Capsule 1 before the end of Cycle 166A, but the total number of failures is unknown due to the lack of FG release data in the later cycles. Based primarily on evidence from the gross gamma counts during Cycle 168A, approximately 15 particles failed in Capsule 3 and four particles failed in Capsule 2. In-pile failures in Capsule 3 were anticipated because this capsule was designed to operate beyond the HTGR normal operating temperature range. In contrast, no in-pile failures were identified in the top two capsules (4 and 5) based on the absence of the typical spikes in gross gamma counts and low failure estimates using the AGR model, developed in INL/EXT-14-32970, for R/B of the short-lived isotopes (Kr-89 and Xe-137) with minimal leakage from Capsule 1.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Test Plan for the 1600°C Heating Test of AGR-3/4 Compact 3-2

Post irradiation examination (PIE) and heating tests of tristructural isotropic (TRISO)-coated fuel particles, fuel compacts, and graphite from the Advanced Gas Reactor (AGR) irradiation experiment AGR 3/4 is in progress. The AGR-3/4 test train consisted of twelve separate capsules irradiated in the northeast flux trap of the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) from December 14, 2011, to April 12, 2014 (Collin 2015). This test plan describes the heating test of AGR-3/4 Compact 3-2. The heating test will involve heating the compact in the Fuel Accident Condition Simulator (FACS) furnace to a peak temperature of 1600°C while collecting fission products released from the compact for subsequent analysis. One of several features of AGR-3/4 that set it apart from AGR-1 and AGR-2 is the incorporation of 20 designed-to-fail (DTF) particles in each compact. The fuel kernels in the DTF particles were coated only with a thin (20 µm thick) pyrocarbon layer having high anisotropy such that the coating should most-likely fail during the irradiation, resulting in up to 20 exposed kernels per compact. One of the main goals of this test is to assess the retention of fission products in the exposed kernels and the surrounding graphitic matrix material comprising the compact. Future heating tests will expose AGR-3/4 compacts at different temperatures in the FACS furnace (Demkowicz 2017). Additionally, the ability may be developed to heat re-irradiated AGR-3/4 compacts to allow a determination of the retention of short-lived fission products I-131 and Xe-133.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Test Plan for the 1400°C Heating Test of AGR-3/4 Compact 10-4

Post irradiation examination (PIE) and heating tests of tristructural isotropic (TRISO)-coated fuel particles, fuel compacts, and graphite from Advanced Gas Reactor (AGR) irradiation experiment AGR 3/4 is in progress. The AGR-3/4 test train consisted of twelve separate capsules irradiated in the northeast flux trap of the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) from December 14, 2011, to April 12, 2014 (Collin 2015). This test plan describes the heating test of AGR-3/4 Compact 10-4. The test will involve heating the compact in the Fuel Accident Condition Simulator (FACS) furnace to a peak temperature of 1400°C while collecting fission products released from the compact for subsequent analysis. One of several features of AGR-3/4 that set it apart from AGR-1 and AGR-2 is the incorporation of 20 designed-to-fail (DTF) particles in each compact. The fuel kernels in the DTF particles were coated only with a thin (20 µm thick) pyrocarbon layer having high anisotropy such that the coating would most-likely fail during the irradiation, resulting in up to 20 exposed kernels per compact. One of the main goals of this test is to assess the retention of fission products in the exposed kernels and the surrounding graphitic matrix material comprising the compact. Future heating tests will expose a number of AGR-3/4 compacts at different temperatures in the FACS furnace (Demkowicz 2017). Additionally, the ability may be developed to heat re-irradiated AGR-3/4 compacts to allow a determination of the retention of short-lived fission products I-131 and Xe-133.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Test Plan for the 1400°C Heating Test of AGR-3/4 Compact 8-2

Post irradiation examination (PIE) and heating tests of tristructural isotropic (TRISO)-coated fuel particles, fuel compacts, and graphite from Advanced Gas Reactor (AGR) irradiation experiment AGR 3/4 is in progress. The AGR-3/4 test train consisted of twelve separate capsules irradiated in the northeast flux trap of the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) from December 14, 2011, to April 12, 2014 (Collin 2015). This test plan describes the heating test of AGR-3/4 Compact 8-2. The test will involve heating the compact in the Fuel Accident Condition Simulator (FACS) furnace to a peak temperature of 1400°C while collecting fission products released from the compact for subsequent analysis. One of several features of AGR-3/4 that set it apart from AGR-1 and AGR-2 is the incorporation of 20 designed-to-fail (DTF) particles in each compact. The fuel kernels in the DTF particles were coated only with a thin (20 µm thick) pyrocarbon layer having high anisotropy such that the coating would most-likely fail during the irradiation, resulting in up to 20 exposed kernels per compact. One of the main goals of this test is to assess the retention of fission products in the exposed kernels and the surrounding graphitic matrix material comprising the compact. Future heating tests will expose a number of AGR-3/4 compacts at different temperatures in the FACS furnace (Demkowicz 2017). Additionally, the ability may be developed to heat re-irradiated AGR-3/4 compacts to allow a determination of the retention of short-lived fission products I-131 and Xe-133.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Test Plan for the 1200°C Heating Test of AGR-3/4 Compact 10-2

Post irradiation examination (PIE) and heating tests of tristructural isotropic (TRISO)-coated fuel particles, fuel compacts, and graphite from Advanced Gas Reactor (AGR) irradiation experiment AGR 3/4 is in progress. The AGR-3/4 test train consisted of twelve separate capsules irradiated in the northeast flux trap of the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) from December 14, 2011, to April 12, 2014 (Collin 2015). This test plan describes the heating test of AGR-3/4 Compact 10-2. The test will involve heating the compact in the Fuel Accident Condition Simulator (FACS) furnace to a peak temperature of 1200°C while collecting fission products released from the compact for subsequent analysis. One of several features of AGR-3/4 that set it apart from AGR-1 and AGR-2 is the incorporation of 20 designed-to-fail (DTF) particles in each compact. The fuel kernels in the DTF particles were coated only with a thin (20 µm thick) pyrocarbon layer having high anisotropy such that the coating would most-likely fail during the irradiation, resulting in up to 20 exposed kernels per compact. One of the main goals of this test is to assess the retention of fission products in the exposed kernels and the surrounding graphitic matrix material comprising the compact. Future heating tests will expose a number of AGR-3/4 compacts at different temperatures in the FACS furnace (Demkowicz 2017). Additionally, the ability may be developed to heat re-irradiated AGR-3/4 compacts to allow a determination of the retention of short-lived fission products I-131 and Xe-133.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Confirmatory Defect Analyses of AGR-5/6/7 Fuel

The Advanced Gas Reactor (AGR) Fuel Development and Qualification Program has executed a series of experiments to test and qualify tristructural isotropic (TRISO) particle fuels for use in high-temperature gas-cooled reactors. The most recent irradiation experiments, AGR-5/6/7, are testing fuel that was fabricated in near production-scale equipment. There are three important defect fractions that must be characterized, using a deconsolidation-leach-burn-leach (DLBL) method, to better predict and understand fuel performance during irradiation. These are the dispersed uranium fraction (DUF), exposed kernel fraction (EKF), and silicon carbide defect fraction (SDF). The DLBL characterization data from analyses of the four compact batches, fabricated and characterized by the BWX Technologies Nuclear Operations Group (BWXT-NOG), showed unexpectedly higher values for all three defect fractions relative to the parent TRISO particle defect fractions. The DUF and SDF should not have changed significantly during compact fabrication and the apparent increase in the EKF, a metric for particle damage, was higher than anticipated for the compacts with 40% volumetric packing fraction (PF). Analytical results showed no net increase in the EKF for the 25% PF compacts. Compacts from one compact batch of each packing fraction were sent to Oak Ridge National Laboratory (ORNL), along with uncompacted tristructural isotropic (TRISO) particles, overcoated to a thickness targeting a 40% PF, for confirmatory analyses of the defect fractions and determination of the source(s) of damage. The ORNL results did not confirm the BWXT-NOG results for either the DUF or the SDF; the ORNL results showed no significant change in these defect fractions relative to the parent TRISO particle lot. The ORNL results did, however, confirm that a large increase in the exposed kernel fraction was found in the 40% PF compacts and that the 25% PF compacts sustained little if any damage. Data suggest that a large majority of the mechanical damage to the TRISO particles occurred in the overcoater when targeting the 40% PF. The analytical laboratories at both BWXT-NOG and ORNL had inconsistent outcomes on analyses of individual batches. Although the ORNL data is more consistent with the parent TRISO lot and expectations, the data set is too limited in size to justifiably reject suspect data from either laboratory at this time. It is recommended that an additional analysis be done to provide sufficient data for estimating the true defect fractions for interpreting the radionuclide release data during the AGR-5/6/7 irradiation experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AGR-5/6/7 Irradiation Test Final As-run Report

This document presents the as-run analysis of the Advanced Gas Reactor (AGR)-5/6/7 irradiation experiment. AGR-5/6/7 is the last of a series of experiments conducted in the Advanced Test Reactor (ATR) at Idaho National Laboratory in support of the development and qualification of tri-structural isotropic low-enriched fuel for use in high-temperature gas-cooled reactors. The test train contained five separate capsules that were independently controlled and monitored. Each capsule contained multiple 24.91-mm-long and 12.25-mm-dimeter compacts filled with low-enriched uranium carbide/oxide tri-structural isotropic fuel particles. The objectives of the AGR-5/6/7 experiment were to: • Irradiate reference-design fuel particles to support fuel qualification. • Establish operating margins for the fuel, beyond normal operating conditions. • Provide irradiated-fuel performance data and irradiated-fuel samples for post-irradiation examination and safety testing. The primary objective of the AGR-5/6 test (Capsules 1, 2, 4, and 5) was to verify the successful performance of the reference-design fuel under normal operating conditions. The AGR-7 test (Capsule 3) was designed to explore fuel performance at higher temperatures. Its primary objective was to demonstrate the capability of the fuel to withstand conditions beyond normal operating conditions, in support of plant design and licensing. AGR-5/6/7 will also provide irradiated-fuel performance data based on the fission gas release from particles during irradiation. To achieve the test objectives, the AGR-5/6/7 experiment was irradiated in the northeast flux trap of the ATR with a planned duration of 500 effective full-power days. The northeast flux trap was selected because its larger diameter provided greater flexibility for test-train design compared to the Large B positions used for the AGR-1 and AGR-2 irradiations, significantly enhancing test capabilities for the combined irradiation campaigns. Due to delays in the ATR schedule, the AGR-5/6/7 irradiation was significantly shorter than the originally planned 13-cycle schedule. Irradiation began on February 16, 2018 and ended on July 22, 2020, spanning nine ATR cycles (162B–168A) over two and a half years. Thus, the AGR-5/6/7 fuel compacts were irradiated for a total of approximately 360.9 effective full-power days. Final burnup values, on a per-compact basis, ranged from 5.66 to 15.26% fissions per initial heavy metal atom, while fast fluence values ranged from 1.62 to 5.55 × 1025 n/m2 (E >0.18 MeV). Time-averaged volume-averaged fuel temperatures on a capsule basis at the end of irradiation ranged from 756°C in Capsule 5 to 1313°C in Capsule 3 excluding days with significantly lower temperature during the two short powered axial locator mechanism cycles, 163A and 167A. By the end of irradiation, 48 out of 54 installed thermocouples had failed (the bottom three capsules lost all thermocouples). During the first five cycles (162B – 165A), the fission-gas isotope release-rate-to-birthrate (R/B) ratios were stable in the 10-8–10-6 range, and no in-pile particle failures were observed based on the gross gamma counts. During this time, the high exposed kernel fraction and high fuel particle temperatures in Capsule 1 led to a maximum R/B value of around 2 ? 10-6 for Kr-85m. The fission gas release in all capsules started to increase from the second half of Cycle 166A, when a large number of in-pile particle failures occurred in Capsule 1 and a gas line problem in this capsule caused fission gas leakage at various degrees into the other four capsules. This gas line problem also prevented a fission gas release measurement for Capsule 1 during the last three cycles due to gas flow isolation. By the end of irradiation, it is estimated that approximately 15 particles failed in Capsule 3, which was considered possible because the experiment was designed to operate beyond the high-temperature gas-cooled reactor normal operating temperature range. A few hundred in-pile particle failures were estimated for Capsule 1 by the end of Cycle 166A, but the total number of failures is unknown due to the lack of fission gas release data in the later cycles. Additionally, four potential in-pile failures were identified for Capsule 2 during the last cycle, Cycle 168A. In contrast, no in-pile failures were identified in the top two capsules (4 and 5) based on the absence of the typical spikes in gross gamma counts and low failure estimates using the AGR-3/4 R/B per exposed kernel model.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AGR-5/6/7 Irradiation Test Final As-run Report

This document presents the as-run analysis of the Advanced Gas Reactor (AGR) 5/6/7 irradiation experiment. AGR-5/6/7 is the last of a series of experiments conducted in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) in support of the development and qualification of tri-structural isotropic (TRISO) low enriched fuel for use in high-temperature gas-cooled reactors (HTGR). The test train contained five separate capsules that were independently controlled and monitored. Each capsule contained multiple 24.91-mm-long and 12.25-mm-dimeter compacts filled with low-enriched uranium carbide/oxide tri-structural isotropic fuel particles. The objectives of the AGR 5/6/7 experiment were to: 1. Irradiate reference-design fuel particles to support fuel qualification. 2. Establish operating margins for the fuel, beyond normal operating conditions. 3. Provide irradiated-fuel performance data and irradiated-fuel samples for post irradiation examination and safety testing. The primary objective of the AGR-5/6 test (Capsules 1, 2, 4, and 5) was to verify the successful performance of the reference-design fuel under normal operating conditions. The AGR-7 test (Capsule 3) was designed to explore fuel performance at higher temperatures. Its primary objective is to demonstrate the capability of the fuel to withstand conditions beyond normal operating conditions, in support of plant design and licensing. AGR 5/6/7 will also provide irradiated-fuel performance data based on the fission gas release from particles during irradiation. To achieve the test objectives, the AGR-5/6/7 experiment was irradiated in the northeast (NE) flux trap of the ATR with a planned duration of 500 effective full-power days (EFPDs). The NE flux trap was selected because its larger diameter provided greater flexibility for test-train design compared to the Large B positions used for the AGR-1 and AGR-2 irradiations, significantly enhancing test capabilities for the combined irradiation campaigns. Due to delays in the ATR schedule, the AGR-5/6/7 irradiation was significantly shorter than the originally planned 13-cycle schedule. Irradiation began on February 16, 2018 and ended on July 22, 2020, spanning nine ATR cycles (162B?168A) over two and a half years. Thus, the AGR-5/6/7 fuel compacts were irradiated for a total of approximately 360.9 EFPDs. Final burnup values, on a per-compact basis, ranged from 5.66% to 15.26% fissions per initial heavy metal atom, while fast fluence values ranged from 1.62 to 5.55 × 1025 n/m2 (E >0.18 MeV). Time-averaged volume-averaged fuel temperatures on a capsule basis at the end of irradiation ranged from 756°C in Capsule 5 to 1313°C in Capsule 3 excluding days with significantly lower temperature during the two short powered axial locator mechanism cycles, 163A and 167A. By the end of irradiation, 48 out of 54 installed thermocouples (TC) had failed (the bottom three capsules lost all TCs). During the first five cycles (162B ? 165A), fission-gas isotope release-rate-to-birthrate (R/B) ratios were stable in the 10-8?10-6 range, and no in-pile particle failures were observed based on the gross gamma counts. During this time, the high exposed kernel fraction and high fuel particle temperatures in Capsule 1 led to the maximum R/B value of around 2 ? 10-6 for Kr-85m. The fission gas release in all capsules started to increase from the second half of Cycle 166A, when a large number of in-pile particle failures occurred in Capsule 1 and a gas line problem in this capsule caused fission gas leakage at various degrees into the other four capsules. This gas line problem also prevented fission gas release measurement for Capsule 1 during the last three cycles due to gas flow isolation. By the end of irradiation, it is estimated that approximately 15 particle failures in Capsule 3, which was considered possible at the start of the irradiation, since the experiment was designed to operate beyond the high-temperature gas-cooled reactor (HTGR) normal operating temperature range. A few hundred in-pile particle failures were estimated for Capsule 1 by the end of Cycle 166A, but the total number of failures is unknown due to lack of fission gas release data in the later cycles. Additionally, four potential in-pile failures were identified for Capsule 2 during the last cycle, 168A. In contrast, no in-pile failures were identified in the top two capsules (4 and 5) based on absence of the typical spikes in gross gamma counts and low failure estimates using the AGR-3/4 R/B per exposed kernel model.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

ECAR-3873 Acceptance of Nonconforming Fuel for the AGR-5/6/7 Irradiation Experiments

Low-enriched fuel compacts fabricated for the AGR-5/6/7 irradiation experiments did not conform to all fuel specifications. Reasons why the fuel is acceptable for use in the AGR-5/6/7 irradiation are discussed. Revision 1 alters the characterization data for the dispersed uranium and exposed kernel defect fractions. Additional characterization data was obtained for fuel compacts analyzed by Oak Ridge National Laboratory. This enabled statistical outliers to be rejected and to confirm that results obtained from BWX Technologies Nuclear Operations Group were statistically independent of the Oak Ridge results and should be excluded from the analyses. Revision 2 alters the characterization data for the TRISO lot, J52R-16-98005, used in the fabrication of the AGR-5/6/7 fuel. Data from the BWXT J52R-16-98005 Certification package is used to calculate the reported values.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AGR-5/6/7 Fuel Fabrication Report

The U.S. Department of Energy Office of Nuclear Energy (DOE NE) and the Idaho National Laboratory (INL) Advanced Reactor Technologies (ART) Advanced Gas Reactor (AGR) Fuel Development and Qualification program (referred to as AGR Fuel program hereafter) are pursuing qualification of tristructural isotropic (TRISO) coated particle fuel for use in high temperature gas cooled reactors (HTGRs). The AGR Fuel program was established to provide a fuel qualification data set in support of the licensing and operation of an HTGR. BWX Technologies Nuclear Operations Group (BWXT-NOG) was subcontracted to fabricate the fuel for the AGR program. Several investments and innovations were realized in preparation to fabricate fuel for the AGR-5/6/7 irradiation experiments that brought fuel fabrication fully out of the laboratory and into engineering-scale operations. These included: • Increased the kernel fabrication line capacity and uniformity • Upgraded ancillary support equipment and processes for the tristructural isotropic (TRISO) coating furnace • Demonstrated efficient production of the matrix precursor powder by dry jet milling of co mingled components • Demonstrated an engineering-scale method for quick and efficient overcoating TRISO particles with the matrix precursor • Demonstrated an automated, multi cavity compacting system with a volumetric feed system • Demonstrated a combined-cycle thermal treatment furnace These changes increased production rates of some of these processes by an order of magnitude or more while eliminating the use of flammable solvents, multiple grinding and sorting operations, and the weighing out of individual die charges. Three fuel kernel lots were fabricated for production of the fuel for AGR-5/6/7. The initial lot (J52R-16-39316) was certified to fuel specifications but was not used because the kernels had a high fraction of internal fissures that caused an unacceptable fraction of the kernels to fragment when charged to the coating furnace where the TRISO coating would be deposited. Fragmented kernels increased the dispersed uranium in the particles and produced a worrisome fraction of dimpled particles with an elevated probability of in-pile failure. After some efforts to identify the cause of the fissure formation, two additional lots were produced with much lower fissure fractions, J52R-16-69317 and 69318. The latter kernel lot was a backup to the first and was not needed. Multiple kernel batches were composited to form each of the lots so as to simulate a commercial-scale operation where kernel batches would also be composited. Multiple TRISO coating runs were performed and the product characterized so that several could be composited into a TRISO lot. TRISO lot J52R-16-98005 conformed to all fuel specifications except the mean outer pyrocarbon (OPyC) layer thickness was thinner than specified. Furthermore, it was determined that the TRISO lot had a dispersed uranium fraction (DUF) that might result in the compacts not meeting the DUF specification. A review of the role of the OPyC layer and consequences of the DUF by the Technical Coordination Team and INL concluded that the fuel was acceptable for use in the AGR-5/6/7 irradiation experiment. The TRISO particles were overcoated with the matrix precursor that had been produced in a jet-milling operation. The overcoating was performed in equipment originally designed to coat pharmaceuticals. The overcoating process performed well; producing highly spherical and uniform overcoats requiring little upgrading and no recycle or rework. TRISO particles were overcoated with the matrix precursor to achieve nominal volumetric packing fractions (PFs) of TRISO particles of 25% and 40% for the irradiation experiments. The 40% PF compacts occupy the first and fifth test capsule in the test train while the inner three capsules are loaded with 25% PF compacts. The resinated graphite matrix precursor powder was a derivative of the German A3-27 matrix formulation, which differs from previous AGR irradiation campaigns that used an A3-3 formulation. Jet milling of the matrix powder precursor produced a finer mean graphite particle size than the milling operations used for the A3-3 matrix powder precursor. Changes made in the matrix formula and equipment yielded compacts with significantly higher matrix density than was attained in previous AGR irradiation campaigns. The changes in the matrix formulation and the means of milling the powders also complicated resolution of the three fuel compact defect fractions, DUF, exposed kernel fraction (EKF), and the silicon carbide defect fraction (SDF). Characterization data from BWXT-NOG had some anomalous results, so samples of the fuel compacts and overcoated TRISO particles were also analyzed by Oak Ridge National Laboratory (ORNL) to ensure that the defect fractions were accurately characterized.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Reirradiation and Post-reirradiation Heating Tests of Loose AGR-2 TRISO Particles and AGR-3/4 Fuel Compacts

To address the lack of data on the behavior of short-lived fission products I-131 (t1/2 = 8.02 d) and Xe-133 (t1/2 = 5.24 d) in the TRISO fuel system, loose AGR-2 particles and kernels were reirradiated in NRAD and subjected to post-reirradiation heating in the FACS furnace. This provided data on the release of fission products from exposed kernels, and the results were used to establish FACS condensation plate collection efficiencies for temperatures of 1000, 1200, and 1400°C where previously, the only collection efficiencies were for 1600°C tests. These new collection efficiencies were then applied to the NRAD-FACS tests of entire AGR-3/4 fuel compacts. Understanding the relative behavior of short-lived I-131, for example, is important because it is a significant contributor to offsite dose during postulated accidents, and Xe-133 has previously been used as a conservative indicator of I-131 behavior. These data will be used to support refinement of fission product transport models and HTGR source-term analyses.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Safety Testing of AGR-2 UCO Compacts 5-2-2, 2-2-2, and 5-4-1

Post-irradiation examination (PIE) is being performed on tristructural-isotropic (TRISO) coated-particle fuel compacts from the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program second irradiation experiment (AGR-2). This effort builds upon the understanding acquired throughout the AGR-1 PIE campaign, and is establishing a database for the different AGR-2 fuel designs. The AGR-2 irradiation experiment included TRISO fuel particles coated at BWX Technologies (BWXT) with a 150-mm-diameter engineering-scale coater. Two coating batches were tested in the AGR-2 irradiation experiment. Batch 93085 had 508-μm-diameter uranium dioxide (UO 2 ) kernels. Batch 93073 had 427-μm-diameter UCO kernels, which is a kernel design where some of the uranium oxide is converted to uranium carbide during fabrication to provide a getter for oxygen liberated during fission and limit CO production. Fabrication and property data for the AGR-2 coating batches have been compiled and compared to those for AGR-1. The AGR-2 TRISO coatings were most like the AGR-1 Variant 3 TRISO deposited in the 50-mm-diameter ORNL lab-scale coater. In both cases argon-dilution of the hydrogen and methyltrichlorosilane coating gas mixture employed to deposit the SiC was used to produce a finer-grain, more equiaxed SiC microstructure. In addition to the fact that AGR-1 fuel had smaller, 350-μm-diameter UCO kernels, notable differences in the TRISO particle properties included the pyrocarbon anisotropy, which was slightly higher in the particles coated in the engineering-scale coater, and the exposed kernel defect fraction, which was higher for AGR-2 fuel due to the detected presence of particles with impact damage introduced during TRISO particle handling.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fabrication and Comparison of Fuels for Advanced Gas Reactor Irradiation Tests

As part of the program to demonstrate TRISO-coated fuel for the Next Generation Nuclear Plant, a series of irradiation tests of Advanced Gas Reactor (AGR) fuel are being performed in the Advanced Test Reactor (ATR) at the Idaho National Laboratory. In the first test, called “AGR-1,” graphite compacts containing approximately 300,000 coated particles were irradiated from December 2006 until November 2009. Development of AGR-1 fuel sought to replicate the properties of German TRISO-coated particles. No particle failures were seen in the nearly 3-year irradiation to a burn up of 19%. The AGR-1 particles were coated in a two-inch diameter coater. Following fabrication of AGR-1 fuel, process improvements and changes were made in each of the fabrication processes. Changes in the kernel fabrication process included replacing the carbon black powder feed with a surface-modified carbon slurry and shortening the sintering schedule. AGR-2 TRISO particles were produced in a six-inch diameter coater using a change size about twenty-one times that of the two-inch diameter coater used to coat AGR-1 particles. Changes were also made in the compacting process, including increasing the temperature and pressure of pressing and using a different type of press. Irradiation of AGR-2 fuel began in late spring 2010. Properties of AGR-2 fuel compare favorably with AGR-1 and historic German fuel. Kernels are more homogeneous in shape, chemistry and density. TRISO-particle sphericity, layer thickness standard deviations, and defect fractions are also comparable. In a sample of 317,000 particles from deconsolidated AGR-2 compacts, 3 exposed kernels were found in a leach test. No SiC defects were found in a sample of 250,000 deconsolidated particles, and no IPyC defects in a sample of 64,000 particles. The primary difference in properties between AGR-1 and AGR-2 compacts is that AGR-2 compacts have a higher matrix density, 1.6 g/cm3 compared to about 1.3 g/cm3 for AGR-1 compacts. Based on fuel properties, excellence performance is expected for the AGR-2 UCO fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Safety Testing and Destructive Examination of AGR-2 UCO Compact 6-4-3

Post-irradiation examination (PIE) and elevated-temperature safety testing are being performed on tristructural-isotropic (TRISO) coated-particle fuel compacts from the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program’s second irradiation experiment (AGR-2). Details on this irradiation experiment have been previously reported. The AGR-2 PIE effort builds upon the understanding acquired throughout the AGR-1 PIE campaign (Demkowicz et al. 2015) and is establishing a database for the different AGR-2 fuel designs. The AGR-2 irradiation experiment included TRISO fuel particles coated at BWX Technologies (BWXT) with an engineering-scale coater, which had a coating chamber 150 mm in diameter. Two coating batches were tested in the AGR-2 irradiation experiment. Batch G73H-10-93085B had uranium dioxide (UO2) kernels with an average diameter of 508 µm. Batch G83J-14-93073A had UCO kernels with an average diameter of 427 µm; in this kernel design, some of the uranium oxide is converted to uranium carbide during fabrication to provide a getter for oxygen liberated during fission and to limit CO production. Fabrication and property data for the AGR-2 coating batches have been compiled and compared to AGR-1. The AGR-2 TRISO coatings were most like the AGR-1 Variant 3 TRISO deposited in the Oak Ridge National Laboratory (ORNL) laboratory-scale coater, which had a coating chamber 50 mm in diameter (Hunn and Lowden 2006). In both cases, the hydrogen and methyltrichlorosilane coating gas mixture that was used to deposit the SiC was diluted with argon to produce a finer grained, more equiaxed SiC microstructure. In addition to the fact that AGR-1 fuel had smaller UCO kernels that were 350 µm in diameter, other notable differences in the TRISO particle properties included (1) the pyrocarbon anisotropy, which was slightly higher in the particles coated in the engineering-scale coater, and (2) the exposed kernel defect fraction, which was higher for AGR-2 fuel due to the detected presence of particles with impact damage that was introduced during TRISO particle handling.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Safety Testing and Destructive Examination of SGR-2 UCO Compact 2-1-2

Post-irradiation examination (PIE) and elevated-temperature safety testing are being performed on tristructural-isotropic (TRISO) coated-particle fuel compacts from the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program’s second irradiation experiment (AGR-2). Details on this irradiation experiment have been previously reported. The AGR-2 PIE effort builds upon the understanding acquired throughout the AGR-1 PIE campaign and is establishing a database for the different AGR-2 fuel designs. The AGR-2 irradiation experiment included TRISO fuel particles coated at BWX Technologies (BWXT) with an engineering-scale coater, which had a coating chamber 150 mm in diameter. Two coating batches were tested in the AGR-2 irradiation experiment. Batch G73H-10-93085B had uranium dioxide (UO2) kernels with an average diameter of 508 µm. Batch G83J-14-93073A had UCO kernels with an average diameter of 427 µm; in this kernel design, some of the uranium oxide is converted to uranium carbide during fabrication to provide a getter for oxygen liberated during fission and to limit CO production. Fabrication and property data for the AGR-2 coating batches have been compiled and compared to AGR-1. The AGR-2 TRISO coatings were most like the AGR-1 Variant 3 TRISO deposited in the Oak Ridge National Laboratory (ORNL) laboratory-scale coater, which had a coating chamber 50 mm in diameter (Hunn and Lowden 2006). In both cases, the hydrogen and methyltrichlorosilane coating gas mixture that was used to deposit the SiC was diluted with argon to produce a finer grained, more equiaxed SiC microstructure. In addition to the fact that AGR-1 fuel had smaller UCO kernels that were 350 µm in diameter, other notable differences in the TRISO particle properties included (1) the pyrocarbon anisotropy, which was slightly higher in the particles coated in the engineering-scale coater, and (2) the exposed kernel defect fraction, which was higher for AGR-2 fuel due to the detected presence of particles with impact damage that was introduced during TRISO particle handling.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗