Search NASA⌕ Search

SEARCH · Search NASA

Results for “fast pyrolysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Coprocessing Biomass Fast Pyrolysis and Catalytic Fast Pyrolysis Oils with Vacuum Gas Oil in Refinery Hydroprocessing

Fast pyrolysis and catalytic fast pyrolysis (CFP) have been considered to be promising approaches for converting lignocellulosic biomass into liquid bio-oils followed by upgrading to produce fuel-range hydrocarbon products. Co-processing fast pyrolysis and CFP bio-oils with petroleum feedstocks leverages the existing petroleum refining infrastructure, which reduces Capex for the overall conversion technologies for biomass to fuel and enables fast adoption of the technologies and biofuels. Here, we reported the co-processing of different woody fast pyrolysis and CFP bio-oils with petroleum vacuum gas oil (VGO) at 5-25% bio-oil blending levels over a NiMo sulfide catalyst for mild hydrocracking. The catalyst activities over ~300 hours time on stream, the product yield and properties, and the biogenic carbon content in products are provided. Co-processing of the raw fast pyrolysis bio-oil in our configuration was not successful because the instability of the bio-oil resulted in reactor plugging and bio-oil stabilization by hydrogenation enabled their stable co-processing with VGO, whereas the CFP bio-oil can be co-processed without pretreatment. Simultaneous hydrodesulfurization, hydrodeoxygenation, and hydrocracking reactions occurred during co-processing and no obvious decrease in hydrodesulfurization and hydrocracking conversion of VGO was observed, suggesting the minimal impact of co-processed bio-oils on the reaction of VGO and also the simultaneous conversion of bio-oil and VGO to produce fuel products with much-reduced S and O content. Biogenic carbon content in co-processed products calculated by yield mass balance, together with results from isotopic measurements, indicates high biogenic carbon incorporation into liquid hydrocarbon products. In conclusion, higher biogenic carbon incorporation into fuel products was observed when co-processing CFP bio-oils than the fast pyrolysis bio-oils and over 90% of carbon in CFP bio-oil was incorporated into liquid hydrocarbon products.

09 BIOMASS FUELS↗
DOE OSTI2024

Influence of loblolly pine anatomical fractions and tree age on oil yield and composition during fast pyrolysis

Fast pyrolysis of woody materials is a technology pathway for producing renewable fuels and chemicals. This is a presentation of isolating needles, bark, and stemwood from a single tree as well as isolating stemwood and whole tree samples from the same species of tree with different ages and pyrolyzing each individually as well as in mixtures. This gives insight into the role of tree anatomical fractions on the resulting intermediate oil product as well as into interactions between these components. The highest carbon content oil (45.1 wt% as received) was produced from a one-to-one mixture of stemwood and needles, followed by the pure stemwood (43.4–43.8 wt% as received), while the lowest oil carbon content was from a one-to-one blend of bark and needles (26.7 wt% as received). The pyrolysis oil yield (combining oil and aqueous where separation occurred) varied from 54 wt% as received (needles) to 72.3 wt% as received (stemwood). When comparing trees of different ages, we find the change in the ratio of the anatomical fractions is a dominant factor in the product composition and yields, while the product composition and yields vary slightly with tree age when only the stemwood is pyrolyzed. Here, in this study, we present the bench-scale pyrolysis, yields, and product characterization of loblolly pine feedstocks (13- vs. 23 year-old, residues, air-classified residues, whole tree, needles, bark, and stemwood).

09 BIOMASS FUELS↗
DOE OSTI2020

Pilot plant reliability metrics for grinding and fast pyrolysis of woody residues

Here we report on the effects of loblolly pine residue variability on material throughput, pilot plant uptime, operator intervention, product yield, and product quality for grinding, fast pyrolysis, and hydrotreating operations. Preprocessing throughput using a hammer mill varied between 31-48% of nameplate capacity (5 tons/hr). Grinder overloads in the size reduction step were more prevalent for lower ash and higher moisture materials. Fast pyrolysis throughput varied between 57-72% of nameplate capacity (20 kg/hr) and bio-oil yields varied between 46-53% (feedstock carbon to oil, dry basis). During fast pyrolysis operations, downtime was caused by bridging in the feed and char removal systems and plugging in the condensation system. Cohesion of feedstock and char leading to system plugging was less frequent for higher ash feedstocks, and differences in condenser plugging behavior between high and low ash feedstocks were observed. The catalyst stability of the bio-oil stabilization step was strongly dependent on the sulfur content in the bio-oil, which was higher for the high-ash residue oils. Lower moisture content in the starting biomass was consistent with lower sulfur content in bio-oil. Yields and properties of hydrotreated fuel products showed minimal deference among the bio-oils.

Klinger, Jordan↗
DOE OSTI2020

In Situ Catalytic Fast Pyrolysis using Red Mud Catalyst: Impact of catalytic fast pyrolysis temperature and biomass feedstocks

Catalytic fast pyrolysis (CFP) has been considered as a very promising approach for converting lignocellulosic biomass into higher-quality bio-oils followed by hydrotreating to produce fuelrange products. A reactive, robust, and low-cost catalyst is required to drive the CFP process. Red mud, a side-product produced during the refining of bauxite to alumina, appears to be an effective catalyst for in situ CFP of biomass. In this paper, we report the impact of CFP reaction temperature on the conversion of a pinyon juniper feedstock to bio-oils using red mud as the catalyst and then to fuel-range hydrocarbons by hydrotreating of the produced bio-oil. The yield and quality of the CFP bio-oil produced and the yield and quality of hydrotreated final products were determined. When the CFP process temperature was lowered from 450 to 400ºC, the bio-oil yield increased with minimal differences in the oxygen content, hydrogen-to-carbon ratio, water content, etc. In addition, CFP bio-oils at both temperatures were processed in a single-stage continuous hydrotreater without reactor plugging during the testing period (i.e., ~100 hours on stream). The yield of CFP bio-oil produced at 400ºC was lower than the yield at 450ºC. However, the overall yield, from biomass to hydrocarbon fuel, was still higher for CFP processing at 400ºC than for processing at 450ºC. This indicates the potential for enhancing overall carbon efficiency, including CFP processing and hydrotreating, by employing red mud catalysts for biomass pyrolysis and tuning the CFP parameters. Detailed analysis of bio-oil and hydrotreated products showed a lower content of lignin-derived species in both samples. Furthermore, CFP processing of three different biomass feedstocks corroborated red mud catalyst development for producing improved quality bio-oil and, when combined with hydrotreating, for the production of fuel range hydrocarbons.

Santosa, Daniel M.↗
DOE OSTI2020

Selective adsorption removal of carbonyl molecular foulants from real fast pyrolysis bio-oils

A novel sorbent-based separation process has been developed to selectively remove target molecules from the real fast pyrolysis (FP) pine bio-oils. Specifically, zeolitic molecular sieves and functionalized polymeric resins were found to effectively reduce carbonyl content and carboxylic acid number of a real pine fast pyrolysis bio-oils, therefore enhance bio-oil stability and preserve down-stream catalyst. Our results provide the first-time evidence on the potential effectiveness of sorption technology strategy for dealing with real FP bio-oils, reducing the carbonyl-rich FP oils from 7.5 mmolg-1 down to 4 mmolg-1 at 40 ?, which has potential to enable bio-oil stabilization and enhance operation stability for down-stream upgrading/hydrotreating processes.

Church, Aimee L.↗
DOE OSTI2024

The Effect of Air Separations on Fast Pyrolysis Products for Forest Residue Feedstocks

This study investigates the intricate relationship between biomass preprocessing and pyrolysis product yields, employing the air classification technique for the treatment of loblolly pine residues with varying moisture content. A comprehensive exploration of the physicochemical properties of air-classified loblolly pine informs a sophisticated pyrolysis simulation model. Given the complex and multifaceted nature of biomass pyrolysis, operating across diverse temporal and spatial scales, a pyrolysis kinetics-based CFD–DEM simulation method is employed to predict product yields. Results showed that the elevated moisture content amplifies particle adhesiveness, necessitating augmented air velocities for effective separation, thereby influencing the efficiency of the separation process. While carbon and hydrogen contents exhibit relative stability across diverse moisture contents and blower frequencies, the oxygen content undergoes noticeable changes. For example, the oxygen contents were measured as 29.2 and 38.6 wt% in the light fraction of 30% moisture content sample at blower frequencies of 10 and 20 Hz, respectively. An intriguing finding emerges from pyrolysis simulation, indicating that a lower blower frequency in air classification moderately enhances bio-oil yield and significantly improves its quality, particularly in terms of water content. For instance, the water content in the bio-oil was about 1.5% and 10% in the heavy and light fractions, respectively from 10% moisture sample under 15 Hz blower frequency. In summary, a detailed understanding and strategic manipulation of critical material attributes in biomass through efficient fractionation techniques are imperative for advancing fast pyrolysis as a sustainable avenue for renewable energy and chemical production.

09 BIOMASS FUELS↗
DOE OSTI2023

Renewable Diesel Production through Stand-Alone and Co-Hydrotreating of Catalytic Fast Pyrolysis Oil

Catalytic Fast Pyrolysis (CFP) of biomass followed by hydrotreating can be used for the production of renewable transportation fuels, such as sustainable aviation fuel and renewable diesel, which can reduce the dependence on fossil fuels and help achieve greenhouse gas reduction goals. Stand-alone hydrotreating of CFP oil and co-hydrotreating of the CFP oil with straight-run diesel (SRD) showed potential to produce high-quality diesel products in this study. Stand-alone hydrotreating of CFP oil produced a diesel fraction with oxygen content < 0.1 wt.% and an indicated cetane number (ICN) of 45. Co-hydrotreating of CFP oil and SRD using a 1:4 volumetric ratio produced diesel products with 0.1 wt.% of oxygen and ICNs of 42-45. Compared to CoMo/Al2O3, NiMo/Al2O3 was a more attractive catalyst for co-hydrotreating of two streams, leading to a higher carbon efficiency, a higher selectivity of cycloalkanes, a higher ICN, and enhanced desulfurization. Compared to stand-alone hydrotreating of CFP oil, co-hydrotreating with SRD could be achieved at a less severe operating condition and it produced hydrotreated products with a higher carbon efficiency. Synergy between CFP oil and SRD during co-hydrotreating process was suggested by the better experimental results in comparison with theoretical interpolation results. Co-hydrotreating gave high biogenic carbon incorporations of 91%-97% as determined by C-14 analysis.

biomass↗
DOE OSTI2020

Heterodoxy in Fast Pyrolysis of Biomass

As the field of fast pyrolysis has matured, it has been accompanied by a kind of orthodoxy in its practice. Among these orthodoxies are the following: (1) oxygen should be excluded from the pyrolysis process; (2) little sugar is produced during pyrolysis; and (3) the major product of pyrolysis is a low-value emulsion in water. Adherence to these tenets is an impediment to the commercial development of fast pyrolysis. Over the past 15 years, research at Iowa State University’s Bioeconomy Institute has challenged these tenets with what might be called heterodoxy in the science and engineering of fast pyrolysis: adding oxygen producing sugars, and fractionating bio-oil into valorized products. This paper reviews these new approaches to pyrolysis and concludes with an outlook for further developing them.

42 ENGINEERING↗
DOE OSTI2021

Accelerated Aging of Fast Pyrolysis Bio-Oil Using Carbonyl Titration: Laboratory Analytical Procedure (LAP)

This laboratory analytical procedure covers the accelerated aging of fast pyrolysis bio-oils. Bio-oils undergo reactions that result in physical and chemical changes over time. These changes typically result in an increase in molecular weight, decrease in some functional groups such as carbonyls, and an increase in viscosity; additionally, the aging process often leads to phase separation. Studies have shown that accelerated aging of bio-oils using this method closely mimics room temperature aging for long periods of time (over 3 years). This procedure has been developed for the accelerated aging of fast pyrolysis bio-oils only. Fast pyrolysis bio-oils are more reactive than other bio-oils (e.g., catalytic fast pyrolysis) and undergo aging much more rapidly. Therefore, this procedure should only be used for fast pyrolysis bio-oil samples.

09 BIOMASS FUELS↗
DOE OSTI2021

Predicting Thermal Excursions During in situ Oxidative Regeneration of Packed Bed Catalytic Fast Pyrolysis Catalyst

Ex situ catalytic fast pyrolysis (CFP) uses a secondary reactor to upgrade biomass pyrolysis vapors to stabilized CFP oils with reduced oxygen content. In one configuration, the secondary reactor is operated as a packed-bed swing reactor system which allows coke-deactivated beds to be decarbonized in situ while other beds remain online for vapor upgrading. In situ decarbonization must be done carefully to avoid irreversible deactivation and/or physical degradation of catalyst pellets. Given that packed bed reactors are well known to have poor heat transfer characteristics, this is a critical issue impacting scaleability and commercial viability of the technology. To predict thermal excursions during regeneration, finite element computational models have been built to assist in scaling up oxidative decarbonization of a Pt/TiO2 CFP catalyst (0.5 mm spheres) from a bench scale packed bed with 100 g of catalyst to a pilot scale packed bed with 2 kg of catalyst and internal cooling tubes. Based on transient measurements of outlet temperature and effluent CO2 concentration, and using an assumed coke profile and activation energy, this paper demonstrates that specific combinations of effective thermal conductivity and wall heat transfer coefficient can fit bench scale oxidative regeneration data equally well. For the upscaled 2 kg bed, four bench-scale “best fit” parameter pairs give different predictions for location and magnitude of thermal excursions, with the maximum computed bed temperature gradients ranging from 30 °C cm-1 to as high as 3000 °C cm-1. The larger the fraction of heat removal by conduction through the cooling tubes, the greater the differences between the parameter pairs. The modelling results presented in this paper cast doubt on the industrial viability of the proposed combination of catalyst, bed and regeneration process, and point to the need for alternate reactor designs. However, there is considerable uncertainly in some of the key model parameters. The reliability of model predictions can be increased by adding more temperature measurements at key bed locations, testing additional variations in process conditions, performing careful bed dissections to determine the true coke profile, and perhaps most importantly, directly measuring the effective thermal conductivity of the catalyst pellets.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Ex Situ Catalytic Fast Pyrolysis of Lignocellulosic Biomass to Hydrocarbon Fuels: 2020 State of Technology

Biomass catalytic fast pyrolysis (CFP) research was funded by the Bioenergy Technologies Office (BETO) of the U.S. Department of Energy (DOE) to enable technical breakthroughs to help reduce the cost of conversion of biomass to liquid hydrocarbon fuels. The key goals were to achieve a mature plant modeled Minimum Fuel Selling Price of $3/GGE, with greater than 60% greenhouse gas (GHG) reduction over petroleum derived gasoline by 2022. Experimental results at NREL and PNNL, along with lifecycle analysis by ANL show that we achieved these goals based on performance at the bench scale. A Pt/TiO2 catalyst was used in a fixed bed reactor for upgrading pyrolysis vapors from an upstream fast pyrolysis reactor (ex-situ configuration) to produce CFP oil with 16.5% oxygen content. Subsequent co-hydrotreating of 10 vol% of CFP oil with 90 vol% straight run diesel (SRD) at the bench scale yielded greater than 95% carbon efficiency for the CFP oil portion of the feed. Light oxygenated coproducts were recovered from the off gases from the CFP process via adsorption and subsequent desorption. Aspen Plus modeling of purification of the desorbed stream using the UNIFAC property method showed that acetone and methyl-ethyl-ketone can be purified to chemicals grade and sold as coproducts to benefit the economics and reduce GHG emissions attributed to the fuel product. Some of the key risks and uncertainties associated with this process, and potential future work are mentioned in this report.

09 BIOMASS FUELS↗
DOE OSTI2024

Recovery of value-added compounds through fast pyrolysis of apple pomace hydrochar

The environmental challenges associated with food production can be addressed via the thermochemical upcycling of agro-industrial biomass. Two such methods, hydrothermal carbonization (HTC) and pyrolysis, can be coupled to first reduce the water content of wet biomass wastes by producing a hydrochar (HC) via HTC and then a bio-oil via pyrolysis of the HC. However, HTC of biomass results in the formation of secondary char (SC), an amorphous tar-like mixture resulting from organic compounds released into the aqueous phase that adsorb, recondense and polymerize on the parent biomass. This study investigated how HTC temperature impacts the formation of SC from apple pomace and the SC’s subsequent impact on fast pyrolysis products. HCs were produced at temperatures of 175°C, 200°C, and 250°C. Lower HTC temperatures favor the formation of biorefinery platform chemicals such as 5-hydroxymethylfurfural and levulinic acid, while higher temperatures result in increased lignin degradation products (i.e., phenolics). HCs were subjected to fast pyrolysis before and after SC extraction in two analytical pyrolysis instruments. Fast pyrolysis of HC produced compounds similar to those found in SC, but with variations in CO and CO 2 emissions. In conclusion, the combination of SC extraction and fast pyrolysis demonstrates promise for recovering value-added compounds from agro-industrial waste biomass while retaining a solid char for fuel and carbon management.

09 BIOMASS FUELS↗
DOE OSTI2022

Detailed biomass fast pyrolysis kinetics integrated to computational fluid dynamic (CFD) and discrete element modeling framework: Predicting product yields at the bench-scale

Fast pyrolysis is an intricate process due to the variability and anisotropy of lignocellulosic biomass and the complicated chemistry and physics during conversion in a bubbling fluidized bed reactor (BFBR). The complexity of biomass fast pyrolysis lends itself well to computational fluid dynamics (CFD) and discrete element (DEM) analysis, which promises to reduce experimental time and its associated cost. This work investigated switchgrass fast pyrolysis simulated by computational fluid dynamics coupled with a discrete element method to track individual reacting biomass particles throughout a bench-scale BFBR reactor. We accounted for the fast pyrolysis chemistry through a comprehensive reaction scheme with secondary cracking reactions. We performed a three-step reduction for secondary cracking reactions to convert the full cracking scheme into a reduced scheme easily incorporated into our model. We assessed the impact of operational conditions on the steady-state yields of liquid bio-oil, non-condensable gases (NCG), at 550 °C over a range of fluidization numbers (2 – 6 Umf), reported as a ratio to the minimum fluidization velocity (Umf). At steady-state, the volatile bio-oil yield had a range of 49.3–50.4 wt%. Levoglucosan was the primary volatile component present with 21 wt% of the bio-oil while water was the second largest with 20 wt%. The reduction of the secondary reaction schemes did not appreciably affect the overall yields of switchgrass pyrolysis compared to the full secondary scheme.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Opportunities and Challenges for Hydrotreating of Catalytic Fast Pyrolysis Oil to Fuels

Catalytic fast pyrolysis (CFP) provides a versatile platform for producing fuels to combat climate change and meet decarbonizing targets. In this contribution, we will discuss the hydroprocessing of CFP oils to a variety of fuels, including sustainable aviation fuel (SAF), diesel, and marine fuel. Both standalone and co-hydroprocessing with petroleum streams will be covered. Hydrotreating CFP oil at temperatures around 400 Degrees Celsius can produce a highly deoxygenated product with oxygen contents below the detection limit. However, the quality of fuel fractions produced has been a problem, manifesting as low octane numbers for the gasoline-range fraction and low cetane numbers for the diesel-range fraction. Incorporating an initial transition zone for hydrogenation during hydrotreating was shown to dramatically increase the diesel fraction cetane number from 24 to 45. A similar approach enabled the production of a cycloalkane-rich SAF fraction meeting key ASTM 4054 guidelines with respect to density, viscosity, heating value, volatility, freeze and flash point. Over 400 hours of hydrotreating for SAF was demonstrated with no signs of catalyst bed fouling, measured by pressure drop over the catalyst bed. Compared to other fuels, marine fuel is unique in that it does not require complete deoxygenation. We investigated the minimum hydrotreating requirements to produce fuel compatible with very low sulfur fuel oil, and the results suggested 30% reduction in hydrotreating costs for this approach. Co-hydroprocessing offers an opportunity to take advantage of refinery infrastructure and economies of scale although the operation is less flexible with respect to operating conditions. Co-hydroprocessing CFP oil with petroleum streams gave efficient deoxygenation at milder conditions (e.g. at temperatures of 320 Degrees Celsius) than required for standalone hydrotreating. Over 90% incorporation of biogenic carbon in the CFP oil was confirmed by carbon-14 analysis. Hydrotreating of CFP oil, whether by standalone or co-processing, can produce a variety of fuel cuts, whose quality can be tailored by changing process conditions. Challenges remain, including long-term catalyst performance and determining CFP oil quality requirements.

09 BIOMASS FUELS↗
DOE OSTI2021

Global Gas-Phase Oxidation Rates of Select Products from the Fast Pyrolysis of Lignocellulose

The oxidation kinetics for products of fast pyrolysis at low temperatures (<600°C) are not well known. These will be important in effort to model autothermal pyrolysis, which has been recently developed to intensify the process, but which occurs at much lower temperatures than combustion. Furthermore, this study determines global oxidation rates at 400-600°C for three important products of fast pyrolysis: levoglucosan, xylose, and acetic acid. Experiments were performed in a fluidized bed pyrolyzer with the reactor modeled as a series of CSTRs and PFRs to determine reaction rates. Oxidation rates at 500°C for the three model compounds varied by a factor of ten.

09 BIOMASS FUELS↗
DOE OSTI2022

At-Line Sampling and Characterization of Pyrolytic Vapors from Biomass Feedstock Blends Using SPME-GC/MS-PCA: Influence of Char on Fast Pyrolysis

Solid-phase microextraction (SPME) coupled with GC-MS analysis was used for at-line sampling of pyrolytic vapors produced during fast pyrolysis of biomass. The pure and binary blends of switchgrass (SWG) and pine harvest residues (PT6) were used as feedstock. Sequential SPME sampling allowed for monitoring of changes in the pyrolysis vapors as char accumulated in the fluid bed. The concentration and composition of the vapors desorbed from the SPME fibers were investigated using GC-MS, and the data sets were then analyzed using principal component analysis (PCA) to compare the composition of the pyrolysis vapors over the course of the pyrolysis run. The chemical composition of both carbohydrate and lignin fragments varied as the char builds up in the reactor bed. Fragments derived from cellulose and xylan included anhydrosugars, furans and light oxygenated compounds. Lignin fragments included methoxyphenols, phenolic ketones and aldehydes, low molecular weight aromatics. The composition of the carbohydrate fragments changed more than the lignin fragments as the char build-up in the fluid bed. This combination of SPME-GC/MS-PCA were a novel, easy and effective method for measuring the composition and changes in the composition of pyrolysis vapors during the fast pyrolysis process. Here, this work also highlighted the effect of char build-up on the composition of the overall pyrolysis vapors.

09 BIOMASS FUELS↗
DOE OSTI2022

Co-processing catalytic fast pyrolysis oil in an FCC reactor

Here, studies of co-processing catalytic fast pyrolysis (CFP) oil with vacuum gas oil (VGO) are conducted in a Davison Circulating Riser (DCR). The CFP oil (CFPO) for this study was produced by upgrading fast-pyrolysis vapors from pine in an ex-situ fixed-bed reactor. CFPOs were co-processed at up to a volume fraction of 0.05 with VGO at 521 degrees C and 257 kPa. The yields of oil, aqueous phase, tail gas, and coke were measured. The amount of coke was determined from the carbon containing components in the regenerator flue gas. A compositional analysis was conducted with gas chromatography and elemental analyzers. The organic liquids were distilled into gasoline, jet-fuel, diesel, and resid fractions. A biocarbon analysis was conducted on the organic phase and its individual boiling-point fractions. The results show a small decrease in liquid yield and a generally increased gas yield when co-processing CFPO with VGO. The experiments showed that 75%-100% of biocarbon is incorporated into liquid fuels relative to fossil carbon, depending on catalyst and CFPO. The measurements indicate that cracked CFPO components are predominantly included in the jet-fuel and diesel fractions. A techno-economic analysis (TEA) estimated the minimum fuel selling price (MSFP) for fuel-range products derived from FCC co-processing of CFPO at 24 to 29 $\$$/GJ ($\$$2.90 to $\$$3.50 per gasoline-gallon equivalent; GGE) at a yield of 4.87-7.14 GJ/t(biomass) or 40-58 GGE/t.

09 BIOMASS FUELS↗