Search NASA⌕ Search

SEARCH · Search NASA

Results for “fatigue resistance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Additively manufactured Al-Ce-Ni-Mn alloy with improved elevated-temperature fatigue resistance

Here, the high cycle fatigue behavior of an additively manufactured (AM) Al-10.5Ce-3.1Ni-1.2Mn wt% alloy was evaluated at 350 °C. The measured fatigue strength of 50 MPa at this temperature is comparable to the most fatigue resistant wrought Al alloys (2618-T6 and 7079-T6) at 315 °C. Refinement of pore populations through advanced AM processing in the examined alloy led to oxide inclusions becoming dominant fatigue crack initiation sites. The distribution of microstructural features that determine crack initiation was measured by X-ray computed tomography and served as input to make fatigue strength model predictions with various methodologies. A Monte-Carlo based approach that was previously applied to predict the fatigue strength of cast aluminum alloys through pore size distributions yielded accurate predictions for the fatigue strength of this AM alloy. Given the tunability of defect distributions in AM alloys, the sensitivity of the Al-Ce-Ni-Mn alloy fatigue behavior to defect distributions and outstanding elevated-temperature fatigue resistance of this alloy; the results together suggest the possibility of a new generation of fatigue-resistant alloys produced by the additive manufacturing route.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Strain-rate hardening enhances fatigue resistance of AlSi10Mg alloy at 350°C

The high cycle fatigue behavior of laser powder bed fusion processed AlSi10Mg has been investigated at 350 °C (T/T m ∼ 0.7). The alloy exhibited a fatigue strength of 30 MPa defined by runout after 10 7 cycles at a conventional loading frequency of 20 Hz, corresponding to a notable fatigue strength to ultimate tensile strength ratio of 0.73. The surprising fatigue resistance was attributed to the strain-rate hardening effect at high fatigue loading frequency relative to tensile loading rates at 350 °C. The strain-rate hardening effect was validated by performing ultrasonic fatigue tests (20 kHz loading frequency) with three orders of magnitude higher strain-rates than those at conventional loading frequency. The higher strain-rates in ultrasonic fatigue increased the magnitude of strain-rate hardening resulting in longer AlSi10Mg fatigue lives compared to fatigue at conventional frequency, thus confirming the strain-rate hardening effect. The fatigue crack initiation mechanism was strain-rate dependent. Post-mortem microstructural examination revealed intergranular cavitation inside clusters of fine equiaxed grains. The cavities interlinked with each other to initiate near-surface fatigue cracks at conventional frequency. Cavitation occurred to a lesser extent at the ultrasonic frequency. As a result, fatigue cracks initiated at pre-existing processing defects near the surface in ultrasonic fatigue samples. Finally, this investigation underscores the role of fine grain clusters in promoting high-temperature fatigue crack initiation and indicates a possible trade-off between printability via grain refinement and high-temperature fatigue resistance of additively manufactured alloys.

Additive manufacturing↗
DOE OSTI2021

Thermomechanical fatigue resistance of low temperature solder for multiwire interconnects in photovoltaic modules

Novel interconnect technologies leveraging low melting temperature solders, such as multiwire interconnects, are being deployed in photovoltaic (PV) modules for improved reliability through interconnect redundancy and lower thermal loads during interconnection and lamination. However, the equivalency of standardized accelerated testing to field conditions has not yet been established for these emerging technologies. In this study, the thermomechanical fatigue resistance of low temperature solder alloys is investigated and compared to that of conventional SnPb to assess the acceleration behavior of these alloys. While InSn is shown to have sufficient thermomechanical fatigue resistance on the order of that of SnPb, these results indicate Sn–Bi alloys may have poor thermomechanical fatigue resistance at field conditions. The results also show that Sn–Bi alloys have thermal cycling acceleration factors of less than one. This indicates that the standardized accelerated thermal cycling test, such as that in IEC 61215, will produce misleading results for Sn–Bi alloys and that unique testing is required for this PV module architecture. Though accelerated thermal cycling may be a meaningful qualification test for SnPb solder joints, these results suggest that mechanical loading may be a more appropriate test for Sn–Bi multiwire interconnects. This is due to the distinct processing and geometry of multiwire interconnects which may allow for mechanical, rather than strictly metallurgical interconnections.

14 SOLAR ENERGY↗
DOE OSTI2026

Dual-precipitates enhance fatigue resistance in an additively manufactured high-entropy alloy

To accomplish the intense desire of high-strength materials for enhanced energy-efficiency, recent research applies a combined strategy of additive-manufacturing and precipitation-strengthening in high entropy alloys. In a context, Al 0.2 Co 1.5 CrFeNi 1.5 Ti 0.3 nanoprecipitation-strengthened system was developed, demonstrating very convincing strength and toughness. Moreover, additive-manufacturing facilitated additional strength by well-decorated cell-boundaries with blocky L2 1 precipitates and homogeneously distributed L1 2 precipitates. However, fatigue research of this alloy remained unexplored despite being the main precursor for structural applications. In this study low-cycle fatigue behavior of this alloy in both as-built and precipitation-strengthened (aged) conditions has been explored, combined with in-situ neutron diffraction investigation. Findings revealed a substantial cyclic-stress profile and a notable fatigue-life below ±0.50% strain-amplitude, exceeding 10 5 cycles at ±0.30% strain-amplitude. These demonstrate the potential to carry higher payloads with marked engineering-reliability. Residual-stress estimation revealed strain-compatibility between the matrix and L1 2 precipitate, indicating a crack-initiation immune interface. A comparative examination of dislocation character revealed shifting towards pure edge-character in aged alloy indicates precipitates promoted planar-slip during deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Fatigue Behavior and Mechanisms of High-Entropy Alloys

Fatigue failures of structural materials pose enormous risks to in-service structures, as well as human lives. The development of advanced durable structural materials with fatigue resistance has important social impact. The novel concept of high-entropy alloys (HEAs) has engendered considerable attention due to their exhibited unusual mechanical properties, and correspondingly opening a new road to design fatigue-resistant structural materials. Here, the present work discusses and reviews the current findings on fatigue behavior and mechanisms of HEAs. Based on the understanding of fatigue-resistant favorable deformation mechanisms in HEAs, the perspectives from the viewpoint of materials design are provided to advance the development of fatigue-resistant HEAs, and future works are also suggested.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Enhancing fatigue life by ductile-transformable multicomponent B2 precipitates in a high-entropy alloy

Catastrophic accidents caused by fatigue failures often occur in engineering structures. Thus, a fundamental understanding of cyclic-deformation and fatigue-failure mechanisms is critical for the development of fatigue-resistant structural materials. Here we report a high-entropy alloy with enhanced fatigue life by ductile-transformable multicomponent B2 precipitates. Its cyclic-deformation mechanisms are revealed by real-time in-situ neutron diffraction, transmission-electron microscopy, crystal-plasticity modeling, and Monte-Carlo simulations. Multiple cyclic-deformation mechanisms, including dislocation slips, precipitation strengthening, deformation twinning, and reversible martensitic phase transformation, are observed in the studied high-entropy alloy. Its improved fatigue performance at low strain amplitudes, i.e., the high fatigue-crack-initiation resistance, is attributed to the high elasticity, plastic deformability, and martensitic transformation of the B2-strengthening phase. This study shows that fatigue-resistant alloys can be developed by incorporating strengthening ductile-transformable multicomponent intermetallic phases.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Strong tough hydrogels via the synergy of freeze-casting and salting out

Natural load-bearing materials like tendons possess high water content of ~70% but14 are still strong and tough even when used for over 1 million cycles per year, which is owed to the hierarchical assembly of anisotropic structures across multi-length-scales . In imitation of natural systems, various hydrogels have been created via methods like electro-spinning, extrusion, compositing, freeze casting, self-assembly, and mechanical stretching for improved mechanical performance. However, in contrast to tendons, many hydrogels with the same high water content do not show high strength, large toughness or high fatigue resistance. In this work, we present a strategy to produce strong, tough and fatigue resistant hydrogels with multi-length-scale hierarchical architecture using a freezing-assisted salting-out treatment. The produced exemplary poly(vinyl alcohol) hydrogels are highly anisotropic, comprising micrometer-scale honeycomb-like pore walls, which in turn comprise interconnected nanofibrils meshes, entirely physically assembled from polymer chains. These hydrogels are made of 70-95% water but can exhibit ultra-high ultimate stress (23.5 ± 2.7 MPa) and strain (2900 ± 450%), giant 32226 toughness (210 ± 13 MJ/m , 175 ± 8 kJ/m) and remarkable fatigue threshold (10.5 ± 1.3 kJ/m), which are 10 times tougher than natural tendon. The presented strategy could expand the applicability of weak polymeric material, like hydrogels, in practical applications that requires long-term services with high-loads and abrupt-impacts and extend the development of structural hydrogels.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructure-Sensitive modeling of surface roughness and notch effects on extreme value fatigue response

Fatigue life knockdown due to surface roughness induces local stress concentrations. Physical fatigue experiments are crucial to qualify materials for use but are limited in their capability to examine the mechanisms underlying the fatigue crack formation driving force due to these stress concentrations. Microstructure-sensitive computational models can aid in this regard and are employed in this work to examine the effects of surface roughness in Al 7075-T6. Digital microstructure models are subjected to crystal plasticity finite element method (CPFEM) simulations to examine the combined effects of microstructure and grain scale asperities on the driving force for fatigue crack formation. Following elastic–plastic shakedown, mesoscale volume-averaged fatigue indicator parameters (FIPs) are computed within fatigue damage process zones of grains. An increase in the intensity of realistic surface roughness profiles corresponds accordingly to larger FIPs but it is difficult to precisely interpret the mechanisms and effects of this intensification. We thus parametrically investigate surface asperities that couple with microstructure and lack of constraint on slip at the free surface to describe microstructure-sensitive surface roughness knockdown effects on fatigue resistance. The depth of a single valley (i.e., notch) due to surface roughness is found to be more detrimental to fatigue resistance than the radius (i.e., notch width, not to be confused with notch acuity). Finally, we also find that different crystallographic textures, grain morphologies, and number of sampled grains have a limited effect on the depth of influence of these notches.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The Impact of Carbonation Curing on the Fatigue Behavior of Polyvinyl Alcohol Engineered Cementitious Composites (PVA-ECC)

Use of Engineered Cementitious Composites (ECC) has been proven to enhance structural fatigue resistance and reduce the use-phase emissions for transportation infrastructure. Carbonation curing offers an opportunity to reduce the embodied carbon of ECC via direct CO 2 sequestration. In this study, the impact of carbonation curing on ECC’s fatigue resistance was examined. ECC’s CO 2 uptake, static flexural behavior, flexural fatigue performance, and single fiber pull-out behavior were studied experimentally. Midspan deflection up to 3 million cycles under fatigue load, fatigue stress-life relationship, and failure mechanism for carbonation-cured and air-cured ECC were investigated. Carbonation curing was found to significantly improved the fatigue life of ECC and lowered the midspan deflection under the same stress. Further, CO 2 -cured ECC can achieve >20% CO 2 uptake per cement mass after 24-hour carbonation curing. Carbonation curing increased ECC’s flexural strength by 32% and promoted crack width control capability, with maximum post-fatigue crack width reduced from 148 μm to 76 μm. As a result, the positive impact of carbonation curing on the fatigue behavior of ECC simultaneously lowers the embodied and operational carbon of ECC structural members subjected to fatigue loading during service.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Development of Lightweight Structural Materials with Improved Properties for Fission Batteries

Fission batteries require lightweight structural materials that demonstrate structural resilience when subjected to repeated shutdown, transportation, startup cycles, and certain external conditions, including rare events such as seismic vibrations and tsunamis. The objectives of this project are (1) to produce lightweight structural materials whose strength-to-weight ratios and fatigue resistance exceed those of current widely used structural materials such as 316 stainless steels (SS316), and (2) to enhance radiation tolerance of structural materials over a suitable service temperature range. To achieve these, (1) a lattice structure will be produced, (2) advanced modeling and simulation tools will be employed to design lattice structures (e.g., a gyroid structure) that reduce stress concentrations and thus increase fatigue resistance, and (3) one-dimensional (1-D) carbon nanotubes will be added to enhance radiation resistance. To validate our solution, high-temperature tensile and fatigue testing, in combination with microstructure characterization, will be conducted on wrought materials, additively manufactured solid materials, and the designed lightweight lattice structure material. Ion irradiation, microstructure characterization, and nanoindentation will be carried out to investigate the effect of 1-D carbon nanotubes on radiation tolerance. Successful completion of this project will deliver a material to serve as a substitute for current SS316 using the same chemistry but with lighter weight and improved mechanical properties. In addition, a material with carbon nanotubes can be designed for improved radiation tolerance over a suitable service temperature range. This project will establish new techniques in innovative materials/lattice design, advanced macroscale properties prediction, and the application of state-of-the-art processes.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The Fundamental Creep Behavior Model of Gr.91 Alloy by ICME Approach (Final Report)

The current project mainly focused on the fundamental creep cracking mechanism of the Grade 91 system during the operation conditions in the advanced technologies FE power plants and build the link among Composition-Processing Parameters-Phase Stability-Microstructure-Creep Resistance. A model based on computational thermodynamics and diffusion kinetics will be developed to provide guidance on how to improve the creep resistance of the alloy system. The PI mainly investigate the Gr.91 base alloy and weldment with the Integrated Computational Materials Engineering (ICME) approach. The long-term goal of the proposed program is to develop a model for creep and fatigue resistant alloys with different elemental systems, compositions, and processing parameters of weldment and heat-treatment. In addition, new creep and fatigue resistant alloys are to be designed based on the predictions from the model. The computational as well as experimental results include three sections: 1) The compositional optimization and secondary phases evaluation regarding the creep resistance in Grade 91 steel through the CALPHAD approach. In this section, the formation of the critical secondary phases, M23C6, MX and Z-phase were well predicted based on many conditions like the temperature as well as compositions. Meanwhile, the role of different alloying elements was also considered as they will directly affect the formation of the secondary phases mentioned above based on the compositional evolution of the alloying elements. 2) An investigation of Creep Resistance in Grade 91 Steel through Computational Thermodynamics. We systematically considered the evolution of the four critical temperatures, Ac3, Ac1, the threshold of M23C6 and Z-phase, on basis of the computational approach. Meanwhile, the equilibrium cooling as well as Scheil simulations were also considered to perform further predictions based on the different cooling rates. 3) Creep lifetime and microstructural evolution of the Grade 91 steel. In this part, mainly experimental approach was performed on the real creep test from the beginning of the commercial Gr.91 alloys. The alloys were normalized, tempered, welded (Gleeble) and PWHT and finally subjected to the creep lifetime analyses. Finally, all the samples after each process were further characterized based on the OM, XRD and SEM technique to draw final conclusions.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2021

Tailoring Microstructure and Mechanical Properties of Additively-Manufactured Ti6Al4V Using Post Processing

Additively-manufactured Ti-6Al-4V (Ti64) exhibits high strength but in some cases inferior elongation to those of conventionally manufactured materials. Post-processing of additively manufactured Ti64 components is investigated to modify the mechanical properties for specific applications while still utilizing the benefits of the additive manufacturing process. The mechanical properties and fatigue resistance of Ti64 samples made by electron beam melting were tested in the as-built state. Several heat treatments (up to 1000 °C) were performed to study their effect on the microstructure and mechanical properties. Phase content during heating was tested with high reliability by neutron diffraction at Los Alamos National Laboratory. Two different hot isostatic pressings (HIP) cycles were tested, one at low temperature (780 °C), the other is at the standard temperature (920 °C). The results show that lowering the HIP holding temperature retains the fine microstructure (~1% β phase) and the 0.2% proof stress of the as-built samples (1038 MPa), but gives rise to higher elongation (~14%) and better fatigue life. The material subjected to a higher HIP temperature had a coarser microstructure, more residual β phase (~2% difference), displayed slightly lower Vickers hardness (~15 HV10N), 0.2% proof stress (~60 MPa) and ultimate stresses (~40 MPa) than the material HIP’ed at 780 °C, but had superior elongation (~6%) and fatigue resistance. Heat treatment at 1000 °C entirely altered the microstructure (~7% β phase), yield elongation of 13.7% but decrease the 0.2% proof-stress to 927 MPa. The results of the HIP at 780 °C imply it would be beneficial to lower the standard ASTM HIP temperature for Ti6Al4V additively manufactured by electron beam melting.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Peening Techniques for Surface Modification: Processes, Properties, and Applications

Surface modification methods have been applied to metals and alloys to change the surface integrity, obtain superior mechanical properties, and improve service life irrespective of the field of application. In this review paper, current state-of-the-art of peening techniques are demonstrated. More specifically, classical and advanced shot peening (SP), ultrasonic impact peening (UIP), and laser shock peening (LSP) have been discussed. The effect of these techniques on mechanical properties, such as hardness, wear resistance, fatigue life, surface roughness, and corrosion resistance of various metals and alloys, are discussed. This study also reports the comparisons, advantages, challenges, and potential applications of these processes.

microstructure↗
DOE OSTI2025

Impact of droplet oxidation on mechanical properties of an Al-7Si-0.4Mg alloy fabricated with liquid metal jetting

Droplet-on-demand liquid metal jetting (DOD-LMJ) is a new method for additive manufacturing of bulk structural alloys. Here, we report on the microstructure, tensile, and fatigue properties of an Al-7Si-0.4Mg (A356) alloy fabricated with LMJ. Liquid metal droplets were shielded by high-purity Ar gas shroud during deposition. Atom probe tomography revealed that a few nanometers thick (Al-Mg-Si)-O oxide film formed on the droplets despite Ar gas shielding. Tensile tests on peak-aged LMJ A356 alloy showed that yield strength was isotropic (250 MPa), but ductility was lower in the build direction (6.1 ± 1.4 %) compared to the transverse direction (9.4 ± 1.0 %). Lower ductility in the build direction was attributed to delamination of metal-oxide interfaces at layer boundaries. The ductility and yield strength of LMJ A356 were similar to cast A356 and laser powder bed fused (LPBF) A357 alloys, indicating the limited impact of oxide film on tensile properties. The oxide film severely impacted the fatigue properties. Fatigue resistance of LMJ A356 was limited by fatigue crack initiation at lack-of-fusion defects and fatigue crack propagation along layer boundaries by delamination of the metal-oxide interface. The fatigue strength of LMJ A356 at 60 MPa was lower than cast A356 and LPBF A357 alloys in the peak-aged condition. This research underscores the need for managing droplet oxidation during LMJ additive manufacturing of structural alloys.

42 ENGINEERING↗