Search NASA⌕ Search

SEARCH · Search NASA

Results for “fault properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Probing the evolution of fault properties during the seismic cycle with deep learning

We use seismic waves that pass through the hypocentral region of the 2016 M6.5 Norcia earthquake together with Deep Learning (DL) to distinguish between foreshocks, aftershocks and time-to-failure (TTF). Binary and N-class models defined by TTF correctly identify seismograms in test with > 90% accuracy. We use raw seismic records as input to a 7 layer CNN model to perform the classification. Here we show that DL models successfully distinguish seismic waves pre/post mainshock in accord with lab and theoretical expectations of progressive changes in crack density prior to abrupt change at failure and gradual postseismic recovery. Performance is lower for band-pass filtered seismograms (below 10 Hz) suggesting that DL models learn from the evolution of subtle changes in elastic wave attenuation. Tests to verify that our results indeed provide a proxy for fault properties included DL models trained with the wrong mainshock time and those using seismic waves far from the Norcia mainshock; both show degraded performance. Our results demonstrate that DL models have the potential to track the evolution of fault zone properties during the seismic cycle. If this result is generalizable it could improve earthquake early warning and seismic hazard analysis.

58 GEOSCIENCES↗

Location of largest earthquake slip and fast rupture controlled by along-strike change in fault structural maturity due to fault growth

Earthquake slip distributions are asymmetric along strike, but the reasons for the asymmetry are unknown. We address this question by establishing empirical relations between earthquake slip profiles and fault properties. We analyze the slip distributions of 27 large continental earthquakes in the context of available information on their causative faults, in particular on the directions of their long-term lengthening. We find that the largest slips during each earthquake systematically occurred on that half of the ruptured fault sections most distant from the long-term fault propagating tips, i.e., on the most mature half of the broken fault sections. Meanwhile, slip decreased linearly over most of the rupture length in the direction of long-term fault propagation, i.e., of decreasing structural maturity along strike. We suggest that this earthquake slip asymmetry is governed by along-strike changes in fault properties, including fault zone compliance and fault strength, induced by the evolution of off-fault damage, fault segmentation, and fault planarity with increasing structural maturity. We also find higher rupture speeds in more mature rupture sections, consistent with predicted effects of low-velocity damage zones on rupture dynamics. Since the direction(s) of long-term fault propagation can be determined from geological evidence, it might be possible to anticipate in which direction earthquake slip, once nucleated, may increase, accelerate, and possibly lead to a large earthquake. Finally, our results could thus contribute to earthquake hazard assessment and Earthquake Early Warning.

58 GEOSCIENCES↗

Specifying and Verifying Ultra-reliability and Fault-tolerance Properties

A methodology to rigorously verify ultrareliability and fault tolerance system properties is described. The methodology utilizes a hierarchy of formal mathematical specifications of system design and incremental design proof to prove the system has the desired properties. A small example of the approach is given, and the application of the methodology to the large scale proof of SIFT, a fault tolerant flight control operating system, is discussed.

Schwartz, R. L.↗

Evolution of Elastic and Mechanical Properties During Fault Shear: The Roles of Clay Content, Fabric Development, and Porosity

Phyllosilicates weaken faults due to the formation of shear fabrics. Although the impacts of clay abundance and fabric on frictional strength, sliding stability, and porosity of faults are well studied, their influence on elastic properties is less known, though they are key factors for fault stiffness. We document the role that fabric and consolidation play in elastic properties and show that smectite content is the most important factor determining whether fabric or porosity controls the elastic response of faults. We conducted a suite of shear experiments on synthetic smectite-quartz fault gouges (10–100 wt% smectite) and sediment incoming to the Sumatra subduction zone. We monitored Vp, Vs, friction, porosity, shear and bulk moduli. We find that mechanical and elastic properties for gouges with abundant smectite are almost entirely controlled by fabric formation (decreasing mechanical and elastic properties with shear). Though fabrics control the elastic response of smectite-poor gouges over intermediate shear strains, porosity is the primary control throughout the majority of shearing. Elastic properties vary systematically with smectite content: High smectite gouges have values of Vp ~ 1,300–1,800 m/s, Vs ~ 900–1,100 m/s, K ~ 1–4 GPa, and G ~ 1–2 GPa, and low smectite gouges have values of Vp ~ 2,300–2,500 m/s, Vs ~ 1,200–1,300 m/s, K ~ 5–8 GPa, and G ~ 2.5–3 GPa. We find that, even in smectite-poor gouges, shear fabric also affects stiffness and elastic moduli, implying that while smectite abundance plays a clear role in controlling gouge properties, other fine-grained and platy clay minerals may produce similar behavior through their control on the development of fabrics and thin shear surfaces.

58 GEOSCIENCES↗

Processed Lab Data for Neural Network-Based Shear Stress Level Prediction

Machine learning can be used to predict fault properties such as shear stress, friction, and time to failure using continuous records of fault zone acoustic emissions. The files are extracted features and labels from lab data (experiment p4679). The features are extracted with a non-overlapping window from the original acoustic data. The first column is the time of the window. The second and third columns are the mean and the variance of the acoustic data in this window, respectively. The 4th-11th column is the the power spectrum density ranging from low to high frequency. And the last column is the corresponding label (shear stress level). The name of the file means which driving velocity the sequence is generated from. Data were generated from laboratory friction experiments conducted with a biaxial shear apparatus. Experiments were conducted in the double direct shear configuration in which two fault zones are sheared between three rigid forcing blocks. Our samples consisted of two 5-mm-thick layers of simulated fault gouge with a nominal contact area of 10 by 10 cm^2. Gouge material consisted of soda-lime glass beads with initial particle size between 105 and 149 micrometers. Prior to shearing, we impose a constant fault normal stress of 2 MPa using a servo-controlled load-feedback mechanism and allow the sample to compact. Once the sample has reached a constant layer thickness, the central block is driven down at constant rate of 10 micrometers per second. In tandem, we collect an AE signal continuously at 4 MHz from a piezoceramic sensor embedded in a steel forcing block about 22 mm from the gouge layer The data from this experiment can be used with the deep learning algorithm to train it for future fault property prediction.

15 GEOTHERMAL ENERGY↗

Contrasts in compliant fault zone properties inferred from geodetic measurements in the San Francisco Bay area

In crustal fault zones, regions of damaged rock characterized by reduced elastic shear modulus can influence patterns of near-field interseismic deformation. In order to study these compliant fault zones (CFZs) and how they might develop over the lifetimes of faults, we compare two fault segments with contrasting fault age and lithology along the San Andreas Fault in the San Francisco Bay Area. New geodetic measurements of the interseismic velocity fields at each location are used to constrain fault zone parameters through a Markov chain Monte Carlo method. At Black Mountain, in the Santa Cruz Mountains of the San Francisco Peninsula, we do not find evidence for a compliant fault zone; instead, we find that the geodetic data are more consistent with a model of a single fault in a homogeneous elastic half-space. At Lake San Andreas, a younger fault segment 35 km farther north, we find evidence for a compliant fault zone about 3.4 +1.1/-1.4 km wide, containing a shear modulus of about 40% of the shear modulus of the surrounding rock. We also find that the best fitting CFZ model at this location, unlike the best fitting homogeneous half-space model, has a locking depth that agrees well with the observed depth of microseismicity. Based on differences in fault age, cumulative displacement, and lithology between Black Mountain and Lake San Andreas, we infer that lithology plays an important and, in this case, perhaps a dominant role in the accumulation of fault zone damage structures and the development of CFZs over the lifetime of a fault.

58 GEOSCIENCES↗

An adjoint-based optimization method for jointly inverting heterogeneous material properties and fault slip from earthquake surface deformation data

SUMMARY Analysis of tectonic and earthquake-cycle associated deformation of the crust can provide valuable insights into the underlying deformation processes including fault slip. How those processes are expressed at the surface depends on the lateral and depth variations of rock properties. The effect of such variations is often tested by forward models based on a priori geological or geophysical information. Here, we first develop a novel technique based on an open-source finite-element computational framework to invert geodetic constraints directly for heterogeneous media properties. We focus on the elastic, coseismic problem and seek to constrain variations in shear modulus and Poisson’s ratio, proxies for the effects of lithology and/or temperature and porous flow, respectively. The corresponding nonlinear inversion is implemented using adjoint-based optimization that efficiently reduces the cost function that includes the misfit between the calculated and observed displacements and a penalty term. We then extend our theoretical and numerical framework to simultaneously infer both heterogeneous Earth’s structure and fault slip from surface deformation. Based on a range of 2-D synthetic cases, we find that both model parameters can be satisfactorily estimated for the megathrust setting-inspired test problems considered. Within limits, this is the case even in the presence of noise and if the fault geometry is not perfectly known. Our method lays the foundation for a future reassessment of the information contained in increasingly data-rich settings, for example, geodetic GNSS constraints for large earthquakes such as the 2011 Tohoku-oki M9 event, or distributed deformation along plate boundaries as constrained from InSAR.

Geochemistry & Geophysics↗

Research Introduction [Slides]

In the topic of Reverse Time Imaging, we proposed a new IC to reduce computation cost but reserve image resolution for distributed sensor networks. For Induced Seismicity in Oklahoma, we analyzed fault stress state analysis at state scale, and we applied machine learning techniques to polarity picking and seismicity rate forecasting. The results provide better understanding of fault properties, stress field, and the relationships among fault, stress state, injections, and potential seismic hazards. Lastly, for Microseismic Monitoring, we detected and located 770 low-frequency events (5-50 Hz): (1) Shallow events are highly clustered, consistent with the pathway from injection well 13-10A to monitoring well; moment tensor inversion shows dominant tensile cracking; (2) Deep events are scattered and show migration pattern to the basement; moment tensors show that most events are shear cracks.

58 GEOSCIENCES↗

Uncertainty quantification for evaluating the impacts of fracture zone on pressure build-up and ground surface uplift during geological CO₂ sequestration

A series of numerical test cases reflecting broad and realistic ranges of geological formation and preexisting fault properties was developed to systematically evaluate the impacts of preexisting faults on pressure buildup and ground surface uplift during CO₂ injection. Numerical test cases were conducted using a coupled hydro-geomechanical simulator, eSTOMP (extreme-scale Subsurface Transport over Multiple Phases). For efficient sensitivity analysis and reliable construction of a reduced-order model, a quasi-Monte Carlo sampling method was applied to effectively sample a high-dimensional input parameter space to explore uncertainties associated with hydrologic, geologic, and geomechanical properties. The uncertainty quantification results show that the impacts on geomechanical response from the pre-existing faults mainly depend on reservoir and fault permeability. When the fault permeability is two to three orders of magnitude smaller than the reservoir permeability, the fault can be considered as an impermeable block that resists fluid transport in the reservoir, which causes pressure increase near the fault. When the fault permeability is close to the reservoir permeability, or higher than 10⁻¹⁵ m² in this study, the fault can be considered as a conduit that penetrates the caprock, connecting the fluid flow between the reservoir and the upper rock.

CO₂ geological sequestration↗

Field characterization of elastic properties across a fault zone reactivated by fluid injection

In this paper, we studied the elastic properties of a fault zone intersecting the Opalinus Clay formation at 300 m depth in the Mont Terri Underground Research Laboratory (Switzerland). Four controlled water injection experiments were performed in borehole straddle intervals set at successive locations across the fault zone. A three-component displacement sensor, which allowed capturing the borehole wall movements during injection, was used to estimate the elastic properties of representative locations across the fault zone, from the host rock to the damage zone to the fault core. Young's moduli were estimated by both an analytical approach and numerical finite difference modeling. Results show a decrease in Young's modulus from the host rock to the damage zone by a factor of 5 and from the damage zone to the fault core by a factor of 2. In the host rock, our results are in reasonable agreement with laboratory data showing a strong elastic anisotropy characterized by the direction of the plane of isotropy parallel to the laminar structure of the shale formation. In the fault zone, strong rotations of the direction of anisotropy can be observed. Finally, the plane of isotropy can be oriented either parallel to bedding (when few discontinuities are present), parallel to the direction of the main fracture family intersecting the zone, and possibly oriented parallel or perpendicular to the fractures critically oriented for shear reactivation (when repeated past rupture along this plane has created a zone).

58 GEOSCIENCES↗

Self-organization via active exploration in robotic applications. Phase 2: Hybrid hardware prototype

In many environments human-like intelligent behavior is required from robots to assist and/or replace human operators. The purpose of these robots is to reduce human time and effort in various tasks. Thus the robot should be robust and as autonomous as possible in order to eliminate or to keep to a strict minimum its maintenance and external control. Such requirements lead to the following properties: fault tolerance, self organization, and intelligence. A good insight into implementing these properties in a robot can be gained by considering human behavior. In the first phase of this project, a neural network architecture was developed that captures some fundamental aspects of human categorization, habit, novelty, and reinforcement behavior. The model, called FRONTAL, is a 'cognitive unit' regulating the exploratory behavior of the robot. In the second phase of the project, FRONTAL was interfaced with an off-the-shelf robotic arm and a real-time vision system. The components of this robotic system, a review of FRONTAL, and simulation studies are presented in this report.

Oegmen, Haluk↗

Earthquake catalog-based machine learning identification of laboratory fault states and the effects of magnitude of completeness

Here, machine learning regression can predict macroscopic fault properties such as shear stress, friction, and time to failure using continuous records of fault zone acoustic emissions. Here we show that a similar approach is successful using event catalogs derived from the continuous data. Our methods are applicable to catalogs of arbitrary scale and magnitude of completeness. We investigate how machine learning regression from an event catalog of laboratory earthquakes performs as a function of the catalog magnitude of completeness. We find that strong model performance requires a sufficiently low magnitude of completeness, and below this magnitude of completeness, model performance saturates.

58 GEOSCIENCES↗

A Reinforcement Learning Approach to Augment Conventional PID Control in Nuclear Power Plant Transient Operation

The ability of nuclear reactors to operate their power conversion cycles more flexibly will enhance their value to energy grids with variable pricing. Current nuclear control systems are typically classical controllers that are often based on proportional-integral-derivative (PID) control. This paper presents a method of augmenting the existing PID control for difficult transient operations in nuclear power plants using a reinforcement learning–derived feedforward signal applied in real time. The agents, which are trained on a test thermal load-following problem, are designed to improve steam generator outlet temperature control for a range of fast load-following scenarios covering ramp rates from 9%/min to 15%/min. Several reinforcement learning algorithms were initially investigated for the training of the feedforward agents with deep Q-learning (DQN) and proximal policy optimization (PPO) networks, which were found to be the most promising. The DQN controllers utilize discrete actions, giving them a better disturbance rejection at steady state but inconsistent response to initial temperature deviations. In contrast, PPO-trained agents, which take continuous actions except for a dead zone around zero, were shown to have the best combination of high disturbance rejection at steady state and good tracking of the desired temperature value. The ability of the PPO agent was also examined, with the average time of decision making found to be on the order of 1 ms. The fault properties of the controller under the loss of the reinforcement learning agent feedforward signal were also examined. The controller showed strong performance in situations of “no-signal” faults. but was less good at handling “stuck-at” faults, where the feedforward signal remains at a set value. In both cases, however, the PID was able to successfully maintain stability, eventually returning the system to a steady state. It is hoped that this work will allow for the proposed control architecture to be examined for more difficult control problems such that it may eventually be used to adapt existing nuclear plants for more aggressive load-following on grids of the future.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Electrical and optical properties of stacking faults introduced by plastic deformation in 4H-SiC

The electrical and optical properties of stacking faults (SFs) introduced by plastic deformation in 4H-SiC were studied by Electron Beam Induced Current (EBIC) and cathodoluminescence (CL) methods. Partial dislocations and stacking faults in the (0001) glide planes perpendicular to the surface were introduced in n-type 4H-SiC under a well-controlled state of stress by cantilever bending at 550°C. CL measurements allow determining the multiplicity of the SFs (single or double). It is observed that the overwhelming majority of stacking faults are double Shockley type SFs (CL emission at 504 nm) that correlates well with previously published high resolution transmission electron microscopy (HRTEM) investigations. However, single Shockley type SFs (CL emission at 422 nm) of much smaller lengths are also observed in some areas near the scratched region from where the defects are nucleated. This suggests that the velocity of partial dislocation pairs under a given applied stress could be higher than that of single partial dislocations. It is also shown that in the EBIC mode, SFs produce a strong bright contrast, which can be explained by considering the SFs in 4H-SiC to be quantum wells of II type.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Potential seal bypass and caprock storage produced by deformation-band-to-opening-mode-fracture transition at the reservoir/caprock interface

Here, we examined the potential impact on CO 2 transport of zones of deformation bands in reservoir rock that transition to opening-mode fractures within overlying caprock. Sedimentological and petrophysical measurements were collected along an approximately 5 m × 5 m outcrop of the Slick Rock and Earthy Members of the Entrada Sandstone on the eastern flank of the San Rafael Swell, Utah, USA. Measured deformation band permeability (2 mD) within the reservoir facies is about three orders of magnitude lower than the host sandstone. Average permeability of the caprock facies (0.0005 mD) is about seven orders of magnitude lower than the host sandstone. Aperture-based permeability estimates of the opening-mode caprock fractures are high (3.3 × 10 7 mD). High-resolution CO 2 –H 2 O transport models incorporate these permeability data at the millimeter scale. We then varied fault properties at the reservoir/caprock interface between open fractures and deformation bands as part of a sensitivity study. Numerical modeling results suggest that zones of deformation bands within the reservoir strongly compartmentalize reservoir pressures largely blocking lateral, cross-fault flow of supercritical CO 2 . Significant vertical CO 2 transport into the caprock occurred in some scenarios along opening-mode fractures. The magnitude of this vertical CO 2 transport depends on the small-scale geometry of the contact between the opening-mode fracture and the zone of deformation bands, as well as the degree to which fractures penetrate caprock. Finally, the presence of relatively permeable units within the caprock allows storage of significant volumes of CO 2 , particularly when the fracture network does not extend all the way through the caprock.

58 GEOSCIENCES↗

On behaviour and scaling of small repeating earthquakes in rate and state fault models

With abundant seismic data for small repeating earthquakes, it is important to construct a dynamic model that can explain various aspects of related observations. We report on small repeating earthquakes on a fault governed by rate- and state-dependent friction laws. The earthquakes occur on a velocity-weakening patch surrounded by a much larger velocity-strengthening region. The whole fault is subject to long-term tectonic loading. The model with a circular patch and the aging form of rate- and state-dependent friction laws has been shown to reproduce the scaling of recurrence time versus seismic moment for small repeating earthquakes in a previous study. In this work we investigate the behaviour of small repeating earthquakes in related models under different scenarios, including several forms of the state evolution equations in rate- and state-dependent friction laws, rectangular velocity-weakening patch geometries, quasi-dynamic versus fully dynamic representation of inertial effects and 2-D versus 3-D simulations. We discover that the simulated scalings between the recurrence time and seismic moment for these different scenarios is similar while differences do exist. We propose a theoretical consideration for the scaling between the recurrence time and seismic moment of small repeating earthquakes. For patch radii smaller than or comparable to the full nucleation size, the scaling is explained by the increase of seismic to aseismic slip ratio with magnitude. For patch radii larger than the full nucleation size, the scaling is explained by the model in which the recurrence time is determined by the earthquake nucleation time, which is in turn determined by the time for aseismic slip to penetrate the distance of the full nucleation size into the patch. The obtained theoretical insight is used to find the combinations of fault properties that allow the model to fit the observed scaling and range of the seismic moment and recurrence time.

58 GEOSCIENCES↗

Quantifying rupture characteristics of microearthquakes in the Parkfield Area using a high-resolution borehole network

It is well known that large earthquakes often exhibit significant rupture complexity such as well separated subevents. With improved recording and data processing techniques, small earthquakes have been found to exhibit rupture complexity as well. Studying these small earthquakes offers the opportunity to better understand the possible causes of rupture complexities. Specifically, if they are random or are related to fault properties. We examine microearthquakes (M < 3) in the Parkfield, California, area that are recorded by a high-resolution borehole network. We quantify earthquake complexity by the deviation of source time functions and source spectra from simple circular (omega-square) source models. We establish thresholds to declare complexity, and find that it can be detected in earthquakes larger than magnitude 2, with the best resolution above M2.5. Comparison between the two approaches reveals good agreement (>90 per cent), implying both methods are characterizing the same source complexity. For the two methods, 60–80 per cent (M 2.6–3) of the resolved events are complex depending on the method. The complex events we observe tend to cluster in areas of previously identified structural complexity; a larger fraction of the earthquakes exhibit complexity in the days following the M w 6 2004 Parkfield earthquake. Ignoring the complexity of these small events can introduce artefacts or add uncertainty to stress drop measurements. Focusing only on simple events however could lead to systematic bias, scaling artefacts and the lack of measurements of stress in structurally complex regions.

58 GEOSCIENCES↗