SEARCH · Search NASA

Results for “feedstock variability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

12 records

All sources NASA NTRS DOE OSTI

NASA NTRS2019

Discerning the Impact of Powder Feedstock Variability on Structure, Property, and Performance of Selective Laser Melted Alloy 718: A Principal Component Analysis (PCA) of Feedstock Variability

Extensive mechanical, chemical and microstructural analyses were conducted on additively manufactured Alloy 718 to characterize powders from multiple vendors to determine the effects of variations observed in the powders had on the consolidated material. With over 190 variables examined, it was necessary to reduce the number of variables and identify the variables and classes of variables that had the greatest effect. Principle Component Analysis (PCA) was used to reduce the number of variable to effectively 12 while identifying several classes of variables as most important.

Ellis, David↗

NASA NTRS2017

Relationship of Powder Feedstock Variability to Microstructure and Defects in Selective Laser Melted Alloy 718

Powder-bed additive manufacturing processes use fine powders to build parts layer by layer. For selective laser melted (SLM) Alloy 718, the powders that are available off-the-shelf are in the 10-45 or 15-45 micron size range. A comprehensive investigation of sixteen powders from these typical ranges and two off-nominal-sized powders is underway to gain insight into the impact of feedstock on processing, durability and performance of 718 SLM space-flight hardware. This talk emphasizes an aspect of this work: the impact of powder variability on the microstructure and defects observed in the as-fabricated and full heated material, where lab-scale components were built using vendor recommended parameters. These typical powders exhibit variation in composition, percentage of fines, roughness, morphology and particle size distribution. How these differences relate to the melt-pool size, porosity, grain structure, precipitate distributions, and inclusion content will be presented and discussed in context of build quality and powder acceptance.

Characterization↗

NASA NTRS2010

The Roles of Beneficiation in Lunar Work

Natural feedstocks used for any process are intrinsically variable. They may also contain deleterious components or low concentrations of desired fractions. For these three reasons it is standard industrial practice to beneficiate feedstocks. This is true across all industries which trans-form raw materials into standardized units. On the Moon there are three natural resources: vacuum, radiation and regolith. To utilize in situ resources on the Moon it is reasonable to presume some beneficiation of the regolith (ground rock) resource will be desirable if not essential. As on Earth, this will require fundamental understanding of the physics and chemistry of the relevant processes, which are exceeding complex in detail. Further, simulants are essential test articles for evaluation of components and systems planned for lunar deployment. Simulants are of course made from geologic feedstocks. Therefore, there is variation, deleterious components and incorrect concentrations of desired fractions in the feedstocks used for simulants. Thus, simulant production can benefit from beneficiation of the input feedstocks. Beneficiation of geologic feedstocks is the subject of extractive metallurgy. Clearly, NASA has two discrete interests pertaining to the science and technology of extractive metallurgy.

Rickman, Doug L.↗

NASA NTRS2018

Impact of Powder Variability on the Microstructure and Mechanical Behavior of Selective Laser Melted (SLM) Alloy 718

Nickel Alloy 718 has found wide use in high-temperature aerospace applications (up to 700°C), due to a combination of good mechanical properties, environmental resistance, and workability at moderate cost. These properties have led Alloy 718 to early adoption by selective laser melting (SLM) additive manufacturing. This presentation will share results from a comprehensive industry survey of 718 powder feedstock for SLM. The survey focuses on the impact of variability in powder characteristics on build quality, microstructure, tensile and high cycle fatigue in the as-fabricated and machined surface conditions. The investigation includes sixteen powder lots from eight suppliers that are produced by gas atomization or rotary atomization in argon or nitrogen. This research was previously presented and published at the 9th International Symposium on Superalloy 718 & Derivatives and was funded by NASA Space Launch System Liquid Engine Office with the Human Exploration Operations Mission Directorate.

Sudbrack, Chantal↗

NASA NTRS2018

Impact of Powder Variability on the Microstructure and Mechanical Behavior of Selective Laser Melted Alloy 718

Powder-bed additive manufacturing processes use fine powders to build parts layer-by-layer. Alloy 718 powder feedstocks for selective laser melting (SLM) additive manufacturing are produced commercially by both gas and rotary atomization and are available typically in the 10-45 or 15-45 microns size ranges. A comprehensive investigation was conducted to understand the impact of powder variability on the microstructure and mechanical behavior of SLM 718 heat treated to Aerospace Material Specification (AMS) 5664. This study included sixteen virgin powders and three once-recycled powders within the 10-45 and 15-45 microns size ranges that were obtained from seven direct source suppliers and one reseller. Although alike as highly regular spheroids, these powders showed distinct differences in composition (especially Al, C and N contents), particle size distributions, and powder features such as degree of agglomeration, fusion and surface roughness. Compositional differences expectedly had the strongest impact on microstructure. High N and C contents formed TiN-nitrides and/or (Nb,Ti,Mo)-C carbides on the grain boundaries, prevented recrystallization during heat treatment, and resulted in retained (001)-scalloped shaped grains that ranged from 19 to 41 microns in average size. In the absence of this particle pinning, the average grain size of the heat treated SLM 718 ranged from 51 microns to 90 microns. Room temperature tensile and high cycle fatigue (HCF) testing compared as-fabricated (AF) and low stress ground (LSG) surface conditions. Tensile testing revealed consistent behavior between the two surface conditions and amongst the powder lots. The finer grained SLM 718 builds displayed the lowest tensile properties. A SLM 718 build fabricated from a powder with eight times lower C content showed statistically better tensile properties presumably due to enhanced coarsening of (delta)-Ni3Nb precipitates. The specimens from once-recycled powders had slightly higher tensile strengths and slightly higher ductility compared to their virgin equivalents; once-recycling also did not substantially degrade the mean HCF life. The LSG fatigue lives agreed with conventionally manufactured 718 data, while AF lives exhibited a knock-down due to surface roughness. The fatigue lives of AF specimens were statistically equivalent across powder lots except for one and failures typically initiated at stress concentrators associated with SLM surface asperities. Fatigue testing of low stress ground specimens result in both transgranular and within facet crack initiations. More than half of the cracks initiated from these facets for the machined condition; however, these facets appeared to be within grains that were larger-than-average in size. A nitrogen-atomized powder with fine prior particles of TiN-nitrides and M(Ti,Nb,Mo)C carbides from atomization on powder surfaces resulted in the best fatigue performance with segregation of these particles to the SLM 718 grain boundaries leading to higher resistance to early-stage crack propagation. Typically the fine-grained builds with minor phases along the grain boundaries did not perform well in fatigue, whereas a larger-grain build with lower carbon content and coarser delta-Ni3Nb precipitates showed the next best HCF response. Further details of the build microstructure and its impact on tensile and fatigue behavior was considered.

laser deposition↗

NASA NTRS2004

Autonomous In-Situ Resources Prospector

This presentation will describe the concept of an autonomous, intelligent, rover-based rapid surveying system to identify and map several key lunar resources to optimize their ISRU (In Situ Resource Utilization) extraction potential. Prior to an extraction phase for any target resource, ground-based surveys are needed to provide confirmation of remote observation, to quantify and map their 3-D distribution, and to locate optimal extraction sites (e.g. ore bodies) with precision to maximize their economic benefit. The system will search for and quantify optimal minerals for oxygen production feedstock, water ice, and high glass-content regolith that can be used for building materials. These are targeted because of their utility and because they are, or are likely to be, variable in quantity over spatial scales accessible to a rover (i.e., few km). Oxygen has benefits for life support systems and as an oxidizer for propellants. Water is a key resource for sustainable exploration, with utility for life support, propellants, and other industrial processes. High glass-content regolith has utility as a feedstock for building materials as it readily sinters upon heating into a cohesive matrix more readily than other regolith materials or crystalline basalts. Lunar glasses are also a potential feedstock for oxygen production, as many are rich in iron and titanium oxides that are optimal for oxygen extraction. To accomplish this task, a system of sensors and decision-making algorithms for an autonomous prospecting rover is described. One set of sensors will be located in the wheel tread of the robotic search vehicle providing contact sensor data on regolith composition. Another set of instruments will be housed on the platform of the rover, including VIS-NIR imagers and spectrometers, both for far-field context and near-field characterization of the regolith in the immediate vicinity of the rover. Also included in the sensor suite are a neutron spectrometer, ground-penetrating radar, and an instrumented cone penetrometer for subsurface assessment. Output from these sensors will be evaluated autonomously in real-time by decision-making software to evaluate if any of the targeted resources has been detected, and if so, to quantify their abundance. Algorithms for optimizing the mapping strategy based on target resource abundance and distribution are also included in the autonomous software. This approach emphasizes on-the-fly survey measurements to enable efficient and rapid prospecting of large areas, which will improve the economics of ISRU system approaches. The mature technology will enable autonomous rovers to create in-situ resource maps of lunar or other planetary surfaces, which will facilitate human and robotic exploration.

Dissly, R. W.↗

NASA NTRS2018

Plasticity and Damage Modeling of Stress Asymmetry and Dynamic Behavior of AFS Additive Manufactured Aluminum Alloy 2219

The Solid State Additive Manufacturing (AM) process referred as MELD that fabricated the samples in this study, provides a new path for repairing, coating, joining and additive manufacturing metals and metal matrix composites. This research will be the first application of a physics-based microstructure dependent internal state variable (ISV) plasticity and damage material model to capture the mechanical response of an AM Aluminum Alloy (AA) 2219 via the MELD process. In this research, a microstructure-based internal state variable (ISV) plasticity-damage model was used to capture the mechanical behavior of AFS 2219 aluminum alloy. Aeroprobe Corporation, creator and patent holder for the MELD process, fabricated the material by pushing a solid filler rod of AA2219-T861 material through a hollow rotating tool onto an AA2219 T851 plate substrate. As feedstock, solid or powder precursor metals are pushed through a nonconsumable rotating cylindrical tool. Herein, added layers are deposited and metallurgically bonded to substrate material or previously deposited layers by the heat generated from the rotating tool through plastic deformation of the filler material. Once a layer has been added, the tool height increases, and starts the deposition of the next layer. This process results in beneficial properties such as grain refinement, homogenization and reduced porosity (fully dense). This process will experience temperatures similar to those in the weld nugget zone (WNZ) in friction stir welding (FSW), ranging from 0.6-0.9 Tm, with Tm being the melting point of the material. MELD is highly scalable with AA deposition rates reaching over 1000 cm3/hr, which allows for MELD being used for repairs, coatings, and building components. A motivating factor driving the research for physics-based history dependent material modeling of MELD components is the ability to accurately capture the stress-state and strain rate dependence in the material caused by variations in material microstructure from the MELD processing of new or repaired components. The ISV model incorporates microstructural content and is consistent with continuum level kinematics, kinetics, and thermodynamics. These features allow the ISV model to capture large deformations at the structural scale using the kinematic and isotropic hardening, while microscale damage is obtained from the microstructural features. The benefits of the ISV model arise from the inclusion of structure-property relationships identified from microstructural characterization and experimentation. The Bauschinger effect (BE) is an important concept, vital in the accurate prediction of cyclic stress-strain response of ductile materials such as metals. The ISV model has been successfully used to capture the behavior and damage, and the BE of different aluminum alloys and steels. The ISV model uses kinematic and isotropic hardening to help capture deformations of the material at the macro scale. To understand this hardening relationship, calculating the kinematic and isotropic hardening relationship in the material is warranted for a high-fidelity model. Electron Backscattered Diffraction (EBSD) was used to characterize the as-fabricated microstructure, where a fully-dense equiaxed grain morphology with average grain size of 2.5 μm was observed. Microhardness mapping of the as-built structures, monotonic tension and compression experiments at both quasi-static (0.001/s) strain rates, tension-followed-by-compression and compression-followed-by-tension experiments were performed to obtain the set of plasticity and damage constants necessary to capture strain rate and stress state behavior of this additive material. To calibrate the plasticity-damage model, a single set of constants were determined to capture the different stress states the MELD AA2219. One set of the constants was determined from experimental true stress-strain curves for the tension and compression data. Additionally, microstructural information and data from the open literature were used as the other model constants. This research is a first of its kind for AFS AA2219, includes correlating the ISV model to the monotonic experimental results that capture the isotropic and kinematic plasticity mechanical response.

Rivera, O. G.↗

NASA NTRS1982

Glass shell manufacturing in space

Highly-uniform, hollow glass spheres, which are used for inertial-confinement fusion targets, are formed from metal-organic gel powder feedstock in a drop-tower furnace. The modelling of this gel-to-sphere transformation has consisted of three phases: gel thermochemistry, furnance-to-gel heat transfer, and gravity-driven degradation of the concentricity of the molten shell. The heat transfer from the furnace to the free-falling gel particle was modelled with forced convection. The gel mass, dimensions, and specific heat as well as furnace temperature profile and furnace gas conductivity, were controlled variables. This model has been experimentally verified. In the third phase, a mathematical model was developed to describe the gravity-driven degradation of concentricity in molten glass shells.

Nolen, R. L.↗

NASA NTRS2024

Toward Prebiotic Chemistry on Titan: Impact Experiments on Organic Haze Particles

Impacts are critical to producing the aqueous environments necessary to stimulate prebiotic chemistry on Titan's surface. Furthermore, organic hazes resting on the surface are a likely feedstock of biomolecules. In this work, we conduct impact experiments on laboratory-produced organic haze particles and haze/sand mixtures and analyze these samples for life's building blocks. Samples of unshocked haze and sand particles are also analyzed to determine the change in biomolecule concentrations and distributions from shocking. Across all samples, we detect seven nucleobases, nine proteinogenic amino acids, and five other biomolecules (e.g., urea) using a blank subtraction procedure to eliminate signals due to contamination. We find that shock pressures of 13 GPa variably degrade nucleobases, amino acids, and a few other organics in haze particles and haze/sand mixtures; however, certain individual biomolecules become enriched or are even produced from these events. Xanthine, threonine, and aspartic acid are enriched or produced in impact experiments containing sand, suggesting these minerals may catalyze the production of these biomolecules. On the other hand, thymine and isoleucine/norleucine are enriched or produced in haze samples containing no sand, suggesting catalytic grains are not necessary for all impact shock syntheses. Uracil, glycine, proline, cysteine, and tyrosine are the most unstable to impact-related processing. These experiments suggest that impacts alter biomolecule distributions on Titan's surface, and that organic hazes co-occurring with fine-grained material on the surface may provide an initial source for further prebiotic chemistry on Titan.

impact experiments↗

NASA NTRS2015

A Decision-Support Model for Selecting Additive Manufacturing Versus Subtractive Manufacturing Based on Energy Consumption

This paper presents a simple computational model for determining whether additive manufacturing or subtractive manufacturing is more energy efficient for production of a given metallic part. The key discriminating variable is the fraction of the bounding envelope that contains material – i.e. the volume fraction of solid material. For both the additive process and the subtractive process, the total energy associated with the production of a part is defined in terms of the volume fraction of that part. The critical volume fraction is that for which the energy consumed by subtractive manufacturing equals the energy consumed by additive manufacturing. For volume fractions less than the critical value, additive manufacturing is more energy efficient. For volume fractions greater than the critical value, subtractive manufacturing is more efficient. The model considers the entire manufacturing lifecycle – from production and transport of feedstock material through processing to return of post-production scrap for recycling. Energy consumed by processing equipment while idle is also accounted for in the model. Although the individual energy components in the model are identified and accounted for in the expressions for additive and subtractive manufacturing, values for many of these components may not be currently available. Energy values for some materials’ production and subtractive and additive manufacturing processes can be found in the literature. However, since many of these data are reported for a very specific application, it may be difficult, if not impossible, to reliably apply these data to new process-material manufacturing scenarios since, very often, insufficient information is provided to enable extrapolation to broader use. Consequently, this paper also highlights the need to develop improved knowledge of the energy embodied in each phase of the manufacturing process. To be most valuable, users of the model should determine the energy consumed by their manufacturing process equipment on the basis of energy-per-unit-volume of production for each material of interest – considering both alloy composition and form. Energy consumed during machine idle per unit time should also be determined by the user then scaled to specific processing scenarios. Energy required to generate feedstock material (billet, plate, bar, wire, powder) must be obtained from suppliers.

J K Watson↗

NASA NTRS2013

Flash Cracking Reactor for Waste Plastic Processing

Conversion of waste plastic to energy is a growing problem that is especially acute in space exploration applications. Moreover, utilization of heavy hydrocarbon resources (wastes, waxes, etc.) as fuels and chemicals will be a growing need in the future. Existing technologies require a trade-off between product selectivity and feedstock conversion. The objective of this work was to maintain high plastic-to-fuel conversion without sacrificing the liquid yield. The developed technology accomplishes this goal with a combined understanding of thermodynamics, reaction rates, and mass transport to achieve high feed conversion without sacrificing product selectivity. The innovation requires a reaction vessel, hydrocarbon feed, gas feed, and pressure and temperature control equipment. Depending on the feedstock and desired product distribution, catalyst can be added. The reactor is heated to the desired tempera ture, pressurized to the desired pressure, and subject to a sweep flow at the optimized superficial velocity. Software developed under this project can be used to determine optimal values for these parameters. Product is vaporized, transferred to a receiver, and cooled to a liquid - a form suitable for long-term storage as a fuel or chemical. An important NASA application is the use of solar energy to convert waste plastic into a form that can be utilized during periods of low solar energy flux. Unlike previous work in this field, this innovation uses thermodynamic, mass transport, and reaction parameters to tune product distribution of pyrolysis cracking. Previous work in this field has used some of these variables, but never all in conjunction for process optimization. This method is useful for municipal waste incinerator operators and gas-to-liquids companies.

Timko, Michael T.↗

NASA NTRSDate not supplied

INCORPORATION OF NITROGEN INTO ORGANICS PRODUCED BY FISCHER-TROPSCH TYPE CHEMISTRY

Laboratory simulations have demonstrated that hydrothermal systems have the potential to produce a range of organic compounds through Fischer-Tropsch type (FTT) chemistry. The distribution of products depends on several factors, including the abundance and composition of feedstock molecules, reaction temperature, and the physical and chemical characteristics of catalytic materials included in the reactions. The majority of studies per-formed to date have focused solely on inclusion of CO2 or CO and H2 as the carbon, oxygen and hydrogen sources, which limits the possible products to hydrocarbons, alcohols and carboxylic acids. A few studies have included nitrogen in the form of ammonia, which led to the production of amino acids and nitrogenous bases. Although these demonstrations provide compelling evidence that FTT reactions can produce compounds of interest for the origins of life, such reactions have been conducted under a very limited range of conditions and the synthetic reaction mechanisms have generally not been well-characterized. We have begun a series of laboratory experiments that will incorporate a range of precursor molecules in varying compositions to determine how these variables affect the relative amounts and speciation of life-essential elements in organic molecules produced under FTT conditions. In the present work, we focus on systems containing C, H, O and N. Reaction mixtures contained CO (~60-80 mM), 150 mM ammonium chloride, and water with a native iron catalyst, which also served as a source of H2 through the reduction of water. Three initial experiments were conducted at 110, 154 and 185 °C and heated for several days. Following the reaction, samples were analyzed by gas chromatography-mass spectrometry, direct analysis in real time mass spectrometry and liquid chromatography-mass spectrometry.

A. S. Burton↗