SEARCH · Search NASA
Results for “flight sytems”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
An in-flight interaction of the X-29A canard and flight control system
Many of today's high performance airplanes use high gain, digital flight control systems. These sytems are liable to couple with the aircraft's structural dynamics and aerodynamics to cause an aeroservoelastic interaction. These interactions can be stable or unstable depending upon damping and phase relationships within the system. The details of an aeroservoelastic interaction experienced in flight by the X-29A forward-swept wing airplane. A 26.5-Hz canard pitch mode response was aliased by the digital sampling rate in the canard position feedback loop of the flight control system, resulting in a 13.5-Hz signal being commanded to the longitudinal control surfaces. The amplitude of this commanded signal increased as the wear of the canard seals increased, as the feedback path gains were increased, and as the canard aerodynamic loading decreased. The resultant control surface deflections were of sufficient amplitude to excite the structure. The flight data presented shows the effect of each component (structural dynamics, aerodynamics, and flight control system) for this aeroservoelastic interaction.
Future of Software Engineering Standards
In the new millennium, software engineering standards are expected to continue to influence the process of producing software-intensive systems which are cost-effetive and of high quality. These sytems may range from ground and flight systems used for planetary exploration to educational support systems used in schools as well as consumer-oriented systems.
A design support simulation of the augmentor wing jet STOL research aircraft
The modification of a C-8A (De Havilland Buffalo) aircraft to a STOL configuration is discussed. The modification consisted of the installation of an augmentor-wing jet flap system. System design requirements were investigated for the lateral and directional flight control systems, the lateral and directional axes stability augmentation systems, the engine and Pegasus nozzle control systems, and the hydraulic systems. Operational techniques for STOL landings, control of engine failures, and pilot techniques for improving engine-out go-around performance were examined. Design changes have been identified to correct deficiencies in areas of the airplane control sytems and to improve the airplane flying qualities.
The Techsat-21 Autonomous Sciencecraft Constellation demonstration
The Autonomous Sciencecraft Constellation flight demonstration (ASC) will fly onboard the Air Forces's TechSat-21 constellation. Demonstration of its capabilities in a flight environment will open up tremendous new opportunities in planetary science, space physics, and earth science that would be unreadable without this technology.
Capillary movement of liquid in granular beds
Knowledge of capillary migration of liquids in granular beds in microgravity is essential for the development of a substrate based nutrient delivery sytem for the growth of plants in space. This problem is also interesting from the theoretical as well as the practical point of view. The purpose of this study was to model capillary water propagation through a granular bed in microgravity. In our ground experiments, water propagation is driven primarily by capillary force. Data for spherical partical sizes in the range from 0.46 to 2 mm have been obtained. It was shown that the velocity of water propagation is very sensitive to particle size. Theoretical consideration is also provided. Actual space flight experiments are planned for the future to confirm our results.
Space shuttle/food system study. Volume 2, Appendix A: Active heating system-screening analysis. Appendix B: Reconstituted food heating techniques analysis
Technical data are presented which were used to evaluate active heating methods to be incorporated into the space shuttle food system design, and also to evaluate the relative merits and penalties associated with various approaches to the heating of rehydrated food during space flight. Equipment heating candidates were subject to a preliminary screening performed by a selection rationale process which considered the following parameters; (1) gravitational effect; (2) safety; (3) operability; (4) system compatibility; (5) serviceability; (6) crew acceptability; (7) crew time; (8) development risk; and (9) operating cost. A hot air oven, electrically heated food tray, and microwave oven were selected for further consideration and analysis. Passive, semi-active, and active food preparation approaches were also studied in an effort to determine the optimum method for heating rehydrated food. Potential complexity, cost, vehicle impact penalties, and palatability were considered in the analysis. A summary of the study results is provided along with cost estimates for each of the potential sytems
Advanced Health Management Algorithms for Crew Exploration Applications
Achieving the goals of the President's Vision for Exploration will require new and innovative ways to achieve reliability increases of key systems and sub-systems. The most prominent approach used in current systems is to maintain hardware redundancy. This imposes constraints to the system and utilizes weight that could be used for payload for extended lunar, Martian, or other deep space missions. A technique to improve reliability while reducing the system weight and constraints is through the use of an Advanced Health Management System (AHMS). This system contains diagnostic algorithms and decision logic to mitigate or minimize the impact of system anomalies on propulsion system performance throughout the powered flight regime. The purposes of the AHMS are to increase the probability of successfully placing the vehicle into the intended orbit (Earth, Lunar, or Martian escape trajectory), increase the probability of being able to safely execute an abort after it has developed anomalous performance during launch or ascent phases of the mission, and to minimize or mitigate anomalies during the cruise portion of the mission. This is accomplished by improving the knowledge of the state of the propulsion system operation at any given turbomachinery vibration protection logic and an overall system analysis algorithm that utilizes an underlying physical model and a wide array of engine system operational parameters to detect and mitigate predefined engine anomalies. These algorithms are generic enough to be utilized on any propulsion system yet can be easily tailored to each application by changing input data and engine specific parameters. The key to the advancement of such a system is the verification of the algorithms. These algorithms will be validated through the use of a database of nominal and anomalous performance from a large propulsion system where data exists for catastrophic and noncatastrophic propulsion sytem failures.
NASA's Earth Observing Data and Information System - Near-Term Challenges
NASA's Earth Observing System Data and Information System (EOSDIS) has been a central component of the NASA Earth observation program since the 1990's. EOSDIS manages data covering a wide range of Earth science disciplines including cryosphere, land cover change, polar processes, field campaigns, ocean surface, digital elevation, atmosphere dynamics and composition, and inter-disciplinary research, and many others. One of the key components of EOSDIS is a set of twelve discipline-based Distributed Active Archive Centers (DAACs) distributed across the United States. Managed by NASA's Earth Science Data and Information System (ESDIS) Project at Goddard Space Flight Center, these DAACs serve over 3 million users globally. The ESDIS Project provides the infrastructure support for EOSDIS, which includes other components such as the Science Investigator-led Processing systems (SIPS), common metadata and metrics management systems, specialized network systems, standards management, and centralized support for use of commercial cloud capabilities. Given the long-term requirements, and the rapid pace of information technology and changing expectations of the user community, EOSDIS has evolved continually over the past three decades. However, many challenges remain. Challenges addressed in this paper include: growing volume and variety, achieving consistency across a diverse set of data producers, managing information about a large number of datasets, migration to a cloud computing environment, optimizing data discovery and access, incorporating user feedback from a diverse community, keeping metadata updated as data collections grow and age, and ensuring that all the content needed for understanding datasets by future users is identified and preserved.
The Large UV/Optical/Infrared Surveyor (LUVOIR): Decadal Mission Study Update
NASA commissioned the study of four large mission concepts, including the Large Ultraviolet / Optical / Infrared (LUVOIR) Surveyor, to be evaluated by the 2020 Decadal Survey in Astrophysics. In response, the Science and Technology Definition Team (STDT) identified a broad range of science objectives for LUVOIR that include the direct imaging and spectral characterization of habitable exoplanets around sun-like stars, the study of galaxy formation and evolution, the exchange of matter between galaxies, star and planet formation, and the remote sensing of Solar System objects. To meet these objectives, the LUVOIR Study Office, located at NASA’s Goddard Space Flight Center (GSFC), completed the first design iteration of a 15-m segmented-aperture observatory that would be launched by the Space Launch System (SLS) Block 2 configuration. The observatory includes four serviceable instruments: the Extreme Coronagraph for Living Planetary Systems (ECLIPS), an optical / near-infrared coronagraph capable of delivering 10^-10contrast at inner working angles as small as 2 O/D; the LUVOIR UV Multi-object Spectrograph (LUMOS), which will provide low- and medium-resolution UV (100 – 400 nm) multi-object imaging spectroscopy in addition to far-UV imaging; the High Definition Imager (HDI), a high-resolution wide-field-of-view NUV-Optical-NIR imager; and Pollux, a high-resolution UV spectro-polarimeter being contributed by Centre National d’Etudes Spatiales (CNES).The study team has executed a second design iteration to further improve upon the 15-m concept, while simultaneously studying an 8-m concept. In these proceedings, we provide an update on these two architectures.