Search NASA⌕ Search

SEARCH · Search NASA

Results for “flow conveyance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

The dynamic behavior of articulated pipes conveying fluid with periodic flow rate.

The plane motion of two rigid, straight articulated pipes conveying fluid is examined. In contrast to previous work, the flow rate is not taken as constant, but is allowed to have small periodic oscillations about a mean value, as would be expected in a pump-driven system. It is shown that in the presence of such disturbances, both parametric and combination resonances are possible. When the system can also admit loss of stability by static buckling or by flutter, it is found that the presence of small periodic disturbances constitutes a destabilizing effect. Floquet theory and converging infinite determinant expansions are used to illustrate a basic difference between systems which lose stability by divergence and those that lose stability by flutter. An algebraic criterion is obtained for the minimum amplitude of flow-rate oscillation required for the system to be affected by the presence of small disturbances.

Bohn, M. P.↗
DOE OSTI2025

Computational Modeling of Water Infiltration From Ditches Into Roadway Embankments

Ditches are built along roadways to convey the stormwater runoff. They collect the runoff from the pavement and adjacent drainage areas. Water can move freely in a ditch away from the road surface, thus making it safer for the vehicular traffic. South Carolina DOT expressed interest in studying infiltration of water from ditches into roadway embankments. As part of the current design criteria, it is recommended that the road subgrades be 1.0 foot above the design event water surface elevation in the ditch. The distance between the water surface and bottom of the subbase is referred to as “freeboard”. The purpose of this requirement is to lower the risk of pavement damage by moving the flow away from the pavement, containing the captured flow, and conveying flow received from adjacent properties to outfalls. With changes in roadway design standards, larger shoulders and flatter cross-slopes have moved ditches further away from the pavement and the subbase. These changes could allow for a lower freeboard standard without reducing safety margins due to the increased lateral distance from the subbase to the ditch. The objective of this study is to evaluate whether the current SCDOT criterion requiring the roadway subgrade to be 1 ft above the design-event ditch water surface can be relaxed under selected geometric and soil conditions, particularly where larger shoulder widths and flatter side slopes increase horizontal separation between ditch water and pavement structure.

42 ENGINEERING↗
DOE OSTI2023

Large Format Composite Additive Manufacturing for Low-Head Hydropower

Hydropower with a small elevation change from inlet to outlet, known as “low-head” hydropower, is a relatively untapped resource for reliable green power generation. One major barrier to entry is the cost of the components needed to generate the power. Each installation site is unique, with various head levels, flow rates, and other unique site characteristics that drive up the cost of development and installation. As a result, custom-made components are necessary because the sites are intrinsically inefficient. However, customized parts are generally more expensive to manufacture than ready-made parts. Often times, the cost of custom-made components is so high that the low-head hydropower installation becomes non-viable. Additive manufacturing offers the ability to make custom components, ideal for one-off applications, at low costs that are well suited for the needs of low-head hydropower. Indirect additive manufacturing, such as making tools or dies rather than end use components, can also be used to make low-cost composite tooling as needed for these custom applications. This paper explores the use of additive manufacturing, both directly and indirectly, to produce the components of a turbine system for a low-head hydropower site. The parts were designed to form a unique modular system, which saves time for future designs and iterations. The system has operated for more than three years without failure at a test site in Wisconsin, USA. This work serves as a basis for future application of AM to low-head systems, in which the modular components can be customized for each unique hydropower installation.

36 MATERIALS SCIENCE↗
DOE OSTI2026

CFD Modeling of an 81" Single Slope Barrier Wall Drainage Window for on Grade and Sag Conditions

The main goal of this study is to design a drainage window in an 81" single slope barrier wall for on-grade and sag conditions that could replace the standard ODOT I-3 barrier catch basin. The ODOT design guidelines are as follows: a) Examine configurations of the opening to the flume behind the wall under the wall section to maximize conveyance of flow to a roadside ditch section. b) Examine window lengths and configurations to maximize hydraulic efficiency on a grade up to an absolute maximum window length of 20 ft. c) Use a minimum opening height of 4 in. and consider tapering to an increased height at the outlet to the flume to reduce the potential for debris clogging beneath the barrier section. On-grade locations are analyzed for longitudinal slope up to 5% and spread up to 10 ft. Sag locations, represented by pavement at zero longitudinal slope, are analyzed for water depths up to 18 in. The roadway cross section consists of a 10-ft shoulder at a 4.0% cross slope and pavement at a 1.6% cross slope. All surfaces are represented with Manning’s n = 0.015. Computational fluid dynamics (CFD) is used to perform the analysis. The modeling approach follows previous studies by the authors. The new design is similar to a slotted inlet: a rectangular opening cut into the bottom of a barrier (e.g., a temporary barrier or single slope barrier wall), which typically has a uniform cross section. Findings from laboratory tests of flow under Florida DOT barrier walls were used for additional validation of the modeling approach used in this study.

42 ENGINEERING↗
NASA NTRSDate not supplied

Vertical Lunar Regolith Conveying as a Flight Experiment in Simulated Lunar-Gravity

Regolith conveying will be an essential task for supplying regolith feedstock to In-Situ Resource Utilization (ISRU) reactor systems for regolith processing on the Moon and Mars. The Vertical Lunar Regolith Conveyor (VLRC) is a technology being developed at NASA Kennedy Space Center (KSC) as a regolith transport task for the GCD ISRU FLEET project led by NASA Glenn Research Center (GRC). Single test loop versions of the VLRC are being developed at NASA KSC as a technology demonstration for a flight experiment. The NASA Flight Opportunities program selected the VLRC for a technology demonstration opportunity on a future Blue Origin New Shepard suborbital launch vehicle to study regolith transport physics in a relevant environment in a vacuum chamber under simulated lunar gravity conditions in order to advance its technology readiness level (TRL) for future space applications. The VLRC system includes four primary subsystems to achieve the objectives of the lunar gravity (Lunar-G) flight experiment. (1) An eccentric vibratory conveyor stack to convey regolith particles consisting of three single-loop helical surface conveyors with each actuated by two vibratory motors that vibrate in unison. One of the three single-loops contains a 0.8°-3.1° inclined helical path and the other two contain a 1.6°-6.2° incline. (2) A stick-slip conveyor stack to convey regolith particles consisting of three single-loop helical surface conveyors with each actuated by the same motor to move in unison in a stick-slip motion. One of the three single-loops contains a 0.8°-3.1° inclined helical path and the other two contain a 1.6°-6.2° incline. (3) A regolith containment system to contain the regolith in each single-loop track during launch before the start of the experiment using containment caps that will be lifted in unison at the start of Lunar-G. (4) COTS cameras will record the motion of regolith and tracer particles. Post-flight analysis of the videos will be used to determine convey speeds and flow rates. The VLRC experiment will use the well-known technique of Particle Image Velocimetry (PIV) image analysis to determine the velocity of tracer particles entrained in the regolith flow. This velocity will be used to calculate the mass flow rate of the regolith being conveyed.

ISRU↗
NASA NTRS1977

Acton mass flow system applied to PFBC feed

Dense phase pneumatic conveying and the Acton Mass Flow concept are defined with emphasis on the specific advantages to the coal and dolomite feed to the Pressurized Fluidized Bed Combustor. The transport and feed functions are explored with a comparison of designing the process for a combined function or for individual functions. The equipment required to accomplish these functions is described together with a typical example of sizing and air or gas requirements. A general outline of the control system required to obtain a uniform feed rate is provided. The condition of the coal and dolomite and conveying gas as required to obtain reliable transport and feed will be discussed.

Homburg, E.↗
DOE OSTI2023

Geoelectric Characterization of Hyporheic Exchange Flow in the Bedrock‐Lined Streambed of East Fork Poplar Creek, Oak Ridge, Tennessee

Abstract A multimethod geoelectric survey was implemented between January and March 2022 along a 220‐m long reach of the bedrock‐lined streambed of East Fork Poplar Creek in Oak Ridge, Tennessee to identify locations of surface‐water and groundwater exchange and characterize the subsurface flow paths that convey water between the stream and flood plain. A waterborne self‐potential (WaSP) survey was completed in January 2022 to measure the electric streaming‐potential field in the stream. Electric resistivity tomography (ERT) was performed in March 2022 on the flood plain adjacent to the WaSP survey reach to map the electric resistivity distribution and characterize the hydrogeology and subsurface flow paths that facilitate surface‐water and groundwater exchange in the bedrock‐lined stream. The combination of WaSP and ERT data support the qualitative interpretation that surface‐water and groundwater exchange likely occurs along fractures in outcropping bedrock and along two fault lines that intersect the limestone creek bed.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Hydro-EKG: In-Stream Streaming-potential (SP) Electrical Monitoring of the Lifeblood of Watersheds during Disturbance

In order to develop improved methods for characterization and monitoring of hyporheic exchange along stream and river corridors, this project evaluated and compared concentration (C) and discharge (Q) correlations between the dam-managed, intermittent Rio Grande River and the perennial East Fork Poplar Creek in Oak Ridge, Tennessee. Additionally, a multimethod geoelectric survey was implemented between January and March 2022 along a 220-meter long reach of the bedrock-lined East Fork Poplar Creek in Oak Ridge, Tennessee to identify locations of surface-water and groundwater exchange in the bedrock-lined streambed and characterize the subsurface flow paths that convey water between the stream and flood plain.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2009

Old Faithful Model for Radiolytic Gas-Driven Cryovolcanism at Enceladus

A new model is presented on how chemically driven cryovolcanism might contribute to episodic outgassing at the icy moon Enceladus and potentially elsewhere including Europa and Kuiper Belt Objects. Exposed water ices can become oxidized from radiolytic chemical alteration of near-surface water ice by space environment irradiation. In contact with primordially abundant reductants such as NH3, CH4, and other hydrocarbons, the product oxidants can react exothermically to produce volatile gases driving cryovolcanism via gas-piston forces on any subsurface liquid reservoirs. Radiolytic oxidants such as H2O2 and O2 can continuously accumulate deep in icy regoliths and be conveyed by rheological flows to subsurface chemical reaction zones over million-year time scales indicated by cratering ages for active regions of Enceladus and Europa. Surface blanketing with cryovolcanic plume ejecta would further accelerate regolith burial of radiolytic oxidants. Episodic heating from transient gravitational tides, radioisotope decay, impacts, or other geologic events might occasionally accelerate chemical reaction rates and ignite the exothermic release of cumulative radiolytic oxidant energy. The time history for the suggested "Old Faithful" model of radiolytic gas-driven cryovolcanism at Enceladus and elsewhere therefore consists of long periods of chemical energy accumulation punctuated by much briefer episodes of cryovolcanic activity. The most probable sequence for detection of activity in the current epoch is a long evolutionary phase of slow but continuous oxidant accumulation over billions of years followed by continuous but variable high activity over the past 10(exp 7)-10(exp 8) years. Detectable cryovolcanic activity could then later decline due to near-total oxidation of the rheologically accessible ice crust and depletion the accessible reductant abundances, as may have already occurred for Europa in the more intense radiation environment of Jupiter's magnetosphere. Astrobiological potential of Enceladus could correspondingly be higher than at Europa due to a less extreme state of oxidation and greater residual abundance of organics.

Cooper, John F.↗
NASA NTRS1989

The effects of particle loading on turbulence structure and modelling

The objective of the present research was to extend the Direct Numerical Simulation (DNS) approach to particle-laden turbulent flows using a simple model of particle/flow interaction. The program addressed the simplest type of flow, homogeneous, isotropic turbulence, and examined interactions between the particles and gas phase turbulence. The specific range of problems examined include those in which the particle is much smaller than the smallest length scales of the turbulence yet heavy enough to slip relative to the flow. The particle mass loading is large enough to have a significant impact on the turbulence, while the volume loading was small enough such that particle-particle interactions could be neglected. Therefore, these simulations are relevant to practical problems involving small, dense particles conveyed by turbulent gas flows at moderate loadings. A sample of the results illustrating modifications of the particle concentration field caused by the turbulence structure is presented and attenuation of turbulence by the particle cloud is also illustrated.

Squires, Kyle D.↗
DOE OSTI2026

Development and Full Load Demonstration of a 900°C Solid Particle Receiver for Concentrating Solar Power Applications - noLimits

Sandia National Laboratories (SNL) and the German Aerospace Centre (DLR) are world leaders in the joint and separate development of very high temperature next generation solar concentrator systems using solid particles. This project “noLimits” is meant to provide the critical performance information needed to commercialize DLR’s CentRec® solar receiver and ancillary particle systems (conveying systems, storage vessels, flow control equipment etc.) developed at Sandia National Laboratories (SNL). Performance information (at power levels closer to a small scale Concentrating Solar Power (CSP) plant) will be obtained at full load conditions (2.5 MWt ) and at 900 °C-1000 °C particle outlet temperatures at the National Solar Thermal Test Facility (NSTTF) located at SNL. Heliogen was proposed to be joining the project as a commercial partner to provide the commercialization route for this receiver design, if successful, as Heliogen acquired the intellectual property (IP) from DLR.

14 SOLAR ENERGY↗
DOE OSTI2024

Particle Vertical Mixing and Horizontal Conveyance Within an Ambient Temperature Fluidized Bed

Previous studies have shown the advantages of particle-to-sCO2 fluidized bed (FB) heat exchangers, which include high heat transfer coefficients, low material cost, and the ability to horizontally convey solid particles. This paper outlines the design and testing of a compact cold flow FB test apparatus to characterize horizontal conveyance through convolutions within a 100 kWth FB heat exchanger design. Horizontal conveyance is an advantage in FBs because it enables more compact designs for heat exchangers. Two mass flow rates, 0.5 & 1 kg/s, at the inlet & outlet of the FB. To determine consistency of the flow rates, Student’s t-tests were used to assess whether the inlet & outlet values were statistically similar. The mass flow rate exiting the bed was statistically similar to the flow rate entering the bed for both cases, but each case featured a wider range and standard deviation. The range and standard deviation of the 1 kg/s flow rate was 0.69-1.23 kg/s and 0.12 kg/s respectively, and the 0.5 kg/s test featured a range and standard deviation of 0.37-0.73 kg/s and 0.09 kg/s, respectively. These measurements provide confidence that large-scale designs can successfully horizontally convey particles at ````~1.5x minimum fluidization velocity (U­mf) without significant variation in flow rate. A method to characterize the degree of particle vertical mixing and bubble frequency within the FB is also introduced. By using a high-resolution camera together with particle velocimetry, particle motion in the X and Y directions can be estimated to assess bed mixing and bubble frequency.

Khalaf, Jawad↗
NASA NTRS1996

Analysis of Two-Phase Flow in Damper Seals for Cryogenic Turbopumps

Cryogenic damper seals operating close to the liquid-vapor region (near the critical point or slightly su-cooled) are likely to present two-phase flow conditions. Under single phase flow conditions the mechanical energy conveyed to the fluid increases its temperature and causes a phase change when the fluid temperature reaches the saturation value. A bulk-flow analysis for the prediction of the dynamic force response of damper seals operating under two-phase conditions is presented as: all-liquid, liquid-vapor, and all-vapor, i.e. a 'continuous vaporization' model. The two phase region is considered as a homogeneous saturated mixture in thermodynamic equilibrium. Th flow in each region is described by continuity, momentum and energy transport equations. The interdependency of fluid temperatures and pressure in the two-phase region (saturated mixture) does not allow the use of an energy equation in terms of fluid temperature. Instead, the energy transport is expressed in terms of fluid enthalpy. Temperature in the single phase regions, or mixture composition in the two phase region are determined based on the fluid enthalpy. The flow is also regarded as adiabatic since the large axial velocities typical of the seal application determine small levels of heat conduction to the walls as compared to the heat carried by fluid advection. Static and dynamic force characteristics for the seal are obtained from a perturbation analysis of the governing equations. The solution expressed in terms of zeroth and first order fields provide the static (leakage, torque, velocity, pressure, temperature, and mixture composition fields) and dynamic (rotordynamic force coefficients) seal parameters. Theoretical predictions show good agreement with experimental leakage pressure profiles, available from a Nitrogen at cryogenic temperatures. Force coefficient predictions for two phase flow conditions show significant fluid compressibility effects, particularly for mixtures with low mass content of vapor. Under these conditions, an increase on direct stiffness and reduction of whirl frequency ratio are shown to occur. Prediction of such important effects will motivate experimental studies as well as a more judicious selection of the operating conditions for seals used in cryogenic turbomachinery.

Arauz, Grigory L.↗
NASA NTRS1979

Visualization of turbulence in flow about a bluff body

A visual diagnostic investigation of turbulence in flow about a circular cylinder was conducted in order to gain a physical insight into the model for the structure of turbulence in flow around a bluff body advanced by the vorticity-amplification theory. A frame-by-frame qualitative and quantitative examination of selected movie strips over time intervals up to more than 800 ms was performed. The selective stretching of cross-vortex tubes, their streamwise tilting, the emergence of an organized turbulent flow pattern near the stagnation zone and the growth of a turbulent boundary layer were clearly revealed by the visualization. In particular, the visualization indicated that the cross-vortex tubes conveyed by the diverging stagnation flow constitute a coherent substructure within the overall turbulent flow that is triggered to its fullest manifestation by the stretching mechanism.

Sadeh, W. Z.↗
DOE OSTI2024

Innovating the next generation of commercial smart building software

Nearly 30% of commercial building energy use is wasted due to equipment faults and HVAC controls problems. The result is increased emissions, compromised comfort and productivity, and less reliable coordination of building power needs with a clean grid. The energy impact alone represents $17 billion in potential savings. Today’s smart building software provides a robust solution to address these operational deficiencies. Energy management and information systems (EMIS) are saving up to 9% on average, with two-year paybacks. They are being incorporated into energy management processes, commissioning services, and utility programs. As effective as they are, two barriers prevent even deeper benefits; limited personnel to fix problems once they are identified, and the expense and time to manually implement changes in control systems. In partnership with the research community, the EMIS industry is developing new capabilities to overcome these barriers. Moving beyond siloed products for either fault detection and diagnostics, or optimal control, these new capabilities empower users to not only automatically identify faults, but also to push corrective action, and control improvements to their buildings. In this paper, several areas for enhancements are documented: ‘one-time’ correction of faults such as setpoints, schedules, and economizer lockouts; short-term active testing for automated proportional integral derivative (PID) loop tuning and functional testing; and continuous supervisory control for demand flexibility and year-round efficiency. Results are presented from a pair of partner implementations out of a dozen providers integrating these enhancements into their products, including field tests from across the country, and insights into operator acceptance and integration into operations and maintenance practices.

Casillas, Armando↗
DOE OSTI2025

Compact Counter Flow Fluidized Bed Heat Exchanger (Final Report)

Generation 3 concentrating solar power systems which utilize solid granular media as the heat transfer and storage media hold promise in reducing the levelized cost of electricity relative to generation 2 systems which utilize molten salt. The particles can be heated to temperatures exceeding 800 °C which enables the use of high efficiency supercritical CO 2 Brayton power cycles. A key challenge associate with the use of solid media is its low bulk thermal conductivity which limits the ability to transfer heat from the particles to a working fluid, such as supercritical CO 2 . Tradition shell and tube and shell and plate heat exchangers feature gravity driven particle flow which limits the maximum particle side heat transfer coefficient in these systems to approximately 400 W/m 2 K. A fluidized bed heat exchanger does not rely solely on gravity for particle flow. Instead, enhanced mixing and horizontal conveyance is achieved through fluidization induced through air injection at the bottom of a bed of particles. A tube bundle within the bed conveys the supercritical CO 2 which is heated via the turbulent particle motion at the tube wall.

14 SOLAR ENERGY↗
NASA NTRS1981

Dynamic behavior of continuous cantilevered pipes conveying fluid near critical velocities

The plane motion of a cantilevered pipe conveying fluid is examined when the flow velocity is in the neighborhood of that generating flutter. In contrast to previous studies, the flow velocity is not prescribed as a constant, but is determined from the laws of motion. A system of two nonlinear partial differential equations which are coupled through the nonlinear terms is thereby obtained. The solution is found by the use of the Krylov-Bogoliubov averaging method and the results are discussed indicating the effect of nonlinearities.

Rousselet, J.↗
NASA NTRS1998

Recent Advances in Visualizing 3D Flow with LIC

Line Integral Convolution (LIC), introduced by Cabral and Leedom in 1993, is an elegant and versatile technique for representing directional information via patterns of correlation in a texture. Although most commonly used to depict 2D flow, or flow over a surface in 3D, LIC methods can equivalently be used to portray 3D flow through a volume. However, the popularity of LIC as a device for illustrating 3D flow has historically been limited both by the computational expense of generating and rendering such a 3D texture and by the difficulties inherent in clearly and effectively conveying the directional information embodied in the volumetric output textures that are produced. In an earlier paper, we briefly discussed some of the factors that may underlie the perceptual difficulties that we can encounter with dense 3D displays and outlined several strategies for more effectively visualizing 3D flow with volume LIC. In this article, we review in more detail techniques for selectively emphasizing critical regions of interest in a flow and for facilitating the accurate perception of the 3D depth and orientation of overlapping streamlines, and we demonstrate new methods for efficiently incorporating an indication of orientation into a flow representation and for conveying additional information about related scalar quantities such as temperature or vorticity over a flow via subtle, continuous line width and color variations.

Interrante, Victoria↗