Search NASA⌕ Search

SEARCH · Search NASA

Results for “fluid bed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2013

Fluid bed adsorption of carbon dioxide on immobilized polyethyenimine (PEI): kinetic analysis and breakthrough behavior

The adsorption of carbon dioxide (CO{sub 2}) by immobilized polyethylenimine (PEI) on mesoporous silica was investigated in a fluid bed. The tests were performed to determine breakthrough behavior with varying bed temperature, flow rates and feed concentrations. Experimental breakthrough curves were analyzed using a theoretical 1D model developed by Bohart and Adams. The results showed that Bohart-Adams model was suitable for the normal description of breakthrough curve for the temperature ranges of 40-90{degree}C. The maximum capacity increased with temperature up to 70{degree}C and then decreased. The adsorption rate constant exhibited a negative temperature dependence decreasing as the temperature increased. Parameters characteristic of a fluid bed adsorber were inferred from these breakthrough curves including the breakthrough time, saturation time, critical reactor length, and length of mass transfer zone LMTZ. These parameters can be used to design fluid bed adsorption system without resolving the mechanistic contributions of dispersion, mixing, and intraparticle diffusion.

Breakthrough↗
DOE OSTI2026

Pumped Thermal Energy Storage Using Low-Cost Particles and a Fluid Bed Heat Exchanger for Maximum Power Efficiency

Robust, efficient, cost-effective long-duration electricity storage (LDES) solutions can enhance grid resiliency, support existing transmission and distribution infrastructure, and enable a greater share of low-cost, variable alternative energy sources to penetrate the market. To meet this need, the project team at the National Renewable Energy Laboratory developed a transformative LDES system based on pumped thermal energy storage (TES) using low-cost particles and a fluid bed heat exchanger for maximum power efficiency (PUMP). The PUMP system is composed of high-temperature, low-cost particle TES coupled with an advanced pressurized fluid bed heat exchanger (PFB HX) that supports a high-efficiency pumped thermal energy storage (PTES) system integrated with concentrating solar thermal power (CSP). The PUMP project developed and de-risked a PFB HX and particle CSP system intended to be integrated with reversible turbomachinery and a modeling tool to assess PTES cost and performance.

14 SOLAR ENERGY↗
DOE OSTI2014

Fluid bed gasification – Plasma converter process generating energy from solid waste: Experimental assessment of sulphur species

Highlights: • We investigate gaseous sulphur species whilst gasifying sulphur-enriched wood pellets. • Experiments performed using a two stage fluid bed gasifier – plasma converter process. • Notable SO{sub 2} and relatively low COS levels were identified. • Oxygen-rich regions of the bed are believed to facilitate SO{sub 2}, with a delayed release. • Gas phase reducing regions above the bed would facilitate more prompt COS generation. - Abstract: Often perceived as a Cinderella material, there is growing appreciation for solid waste as a renewable content thermal process feed. Nonetheless, research on solid waste gasification and sulphur mechanisms in particular is lacking. This paper presents results from two related experiments on a novel two stage gasification process, at demonstration scale, using a sulphur-enriched wood pellet feed. Notable SO{sub 2} and relatively low COS levels (before gas cleaning) were interesting features of the trials, and not normally expected under reducing gasification conditions. Analysis suggests that localised oxygen rich regions within the fluid bed played a role in SO{sub 2}’s generation. The response of COS to sulphur in the feed was quite prompt, whereas SO{sub 2} was more delayed. It is proposed that the bed material sequestered sulphur from the feed, later aiding SO{sub 2} generation. The more reducing gas phase regions above the bed would have facilitated COS – hence its faster response. These results provide a useful insight, with further analysis on a suite of performed experiments underway, along with thermodynamic modelling.

09 BIOMASS FUELS↗
DOE OSTI2015

Coupling scales for modelling heavy metal vaporization from municipal solid waste incineration in a fluid bed by CFD

Highlights: • A CFD two-scale model is formulated to simulate heavy metal vaporization from waste incineration in fluidized beds. • MSW particle is modelled with the macroscopic particle model. • Influence of bed dynamics on HM vaporization is included. • CFD predicted results agree well with experimental data reported in literature. • This approach may be helpful for fluidized bed reactor modelling purposes. - Abstract: Municipal Solid Waste Incineration (MSWI) in fluidized bed is a very interesting technology mainly due to high combustion efficiency, great flexibility for treating several types of waste fuels and reduction in pollutants emitted with the flue gas. However, there is a great concern with respect to the fate of heavy metals (HM) contained in MSW and their environmental impact. In this study, a coupled two-scale CFD model was developed for MSWI in a bubbling fluidized bed. It presents an original scheme that combines a single particle model and a global fluidized bed model in order to represent the HM vaporization during MSW combustion. Two of the most representative HM (Cd and Pb) with bed temperatures ranging between 923 and 1073 K have been considered. This new approach uses ANSYS FLUENT 14.0 as the modelling platform for the simulations along with a complete set of self-developed user-defined functions (UDFs). The simulation results are compared to the experimental data obtained previously by the research group in a lab-scale fluid bed incinerator. The comparison indicates that the proposed CFD model predicts well the evolution of the HM release for the bed temperatures analyzed. It shows that both bed temperature and bed dynamics have influence on the HM vaporization rate. It can be concluded that CFD is a rigorous tool that provides valuable information about HM vaporization and that the original two-scale simulation scheme adopted allows to better represent the actual particle behavior in a fluid bed incinerator.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2017

Analysis of maximum pressure drop for a flat-base spouted fluid bed

For design purposes of the blower power requirements during startup of a spouting bed process, knowledge of the maximum pressure drop across a spouting bed at the onset of spouting is required. A survey of the literature for this information lead to only a few correlations which required information from a spouting bed test to be applicable. Therefore, an experimental investigation of this pressure drop and its associated superficial gas velocity in a flat based spouted bed operating with and without fluidization has been conducted. Measurements were performed using a 10 cm cylindrical bed with different static bed heights and two Geldard group B particles (Al2O3 and HDPE). The results show that the taller static bed height creates a larger maximum pressure drop across the bed, as expected. The maximum pressure drop also increases with increasing fluidized gas velocity. In conclusion, the evolution of maximum pressure drop and its velocity were evaluated and a correlation for the maximum pressure drop and its corresponding velocity for spouted and spouted fluid beds were obtained.

42 ENGINEERING↗
DOE OSTI2017

Minimum spouting velocity of flat-base spouted fluid bed

Experiments were performed on spout characteristics of a cylindrical spout-fluidized bed (I.D. = 10 cm) with different static heights and two materials (Al 2 O 3 and high density polyethylene). Results of minimum spouting velocity obtained in this study were compared with reported correlations for both spouted and spout-fluidized beds. Considerable discrepancies were found between the values obtained using different model equations as well as with respect to experimental results. Based on the Mathur–Gishler correlation, a new correlation is proposed for calculating the minimum spouting velocity that introduces the ratio U/U mf . It was found that the minimum spouting velocity decreases with increasing fluidizing gas velocity (U/U mf ). The pressure drop at the point of minimum spouting velocity is also correlated using this dimensionless group and is presented in this work. Finally, this investigation demonstrates that the use of correlations reported in the literature that focus primarily on conical bottom spouted beds are not applicable to flat-bottom spouted and spout-fluidized beds.

42 ENGINEERING↗
DOE OSTI2012

Fluid-Bed Testing of GreatPoint Energy's Direct Oxygen Injection Catalytic Gasification Process for Synthetic Natural Gas and Hydrogen Coproduction: Year 6 - Activity 1.14 - Development of a National Center for Hydrogen Technology

The GreatPoint Energy (GPE) concept for producing synthetic natural gas and hydrogen from coal involves the catalytic gasification of coal and carbon. GPE’s technology “refines” coal by employing a novel catalyst to “crack” the carbon bonds and transform the coal into cleanburning methane (natural gas) and hydrogen. The GPE mild “catalytic” gasifier design and operating conditions result in reactor components that are less expensive and produce pipeline-grade methane and relatively high purity hydrogen. The system operates extremely efficiently on very low cost carbon sources such as lignites, subbituminous coals, tar sands, petcoke, and petroleum residual oil. In addition, GPE’s catalytic coal gasification process eliminates troublesome ash removal and slagging problems, reduces maintenance requirements, and increases thermal efficiency, significantly reducing the size of the air separation plant (a system that alone accounts for 20% of the capital cost of most gasification systems) in the catalytic gasification process.

01 COAL, LIGNITE, AND PEAT↗
NASA NTRS1977

Effluent characterization from a conical pressurized fluid bed

To obtain useable corrosion and erosion results it was necessary to have data with several levels of particulate matter in the hot gases. One level of particulate loading was as low as possible so that ideally no erosion and only corrosion occurred. A conical fluidized bed was used to obtain some degree of filtration through the top of the bed which would not be highly fluidized. This would minimize the filtration required for the hot gases or conversely the amount of particulate matter in the hot gases after a given level of filtration by cyclones and/or filters. The data obtained during testing characterized the effluent from the bed at different test conditions. A range of bed heights, coal flows, air flows, limestone flows, and pressure are represented. These tests were made to determine the best operating conditions prior to using the bed to determine erosion and corrosion rates of typical turbine blade materials.

Priem, R. J.↗
NASA NTRS1977

Effluent characterization from a conical pressurized fluid bed

An important factor regarding the use of a pressurized coal burning fluidized bed (PFB) providing gases for driving a gas turbine is the turbine blade lifetime. However, very little data are currently available to predict erosion and corrosion rates produced by the effluent from a PFB. To assess the potential of alloys developed for aeronautical applications to resist this environment it was decided to build a coal burning fluidized bed that could be employed to measure erosion and corrosion rates. Tests were conducted with a conical fluidized bed to obtain some degree of filtration through the top of the bed. A description is presented of the data obtained in the first 138 hours of testing to characterize the effluent from the bed under different test conditions. The considered tests had been made to determine the best operating conditions prior to using the bed for a determination of the erosion and corrosion rates of typical turbine blade materials.

Priem, R. J.↗
DOE OSTI2012

Two stage fluid bed-plasma gasification process for solid waste valorisation: Technical review and preliminary thermodynamic modelling of sulphur emissions

Highlights: Black-Right-Pointing-Pointer We investigate sulphur during MSW gasification within a fluid bed-plasma process. Black-Right-Pointing-Pointer We review the literature on the feed, sulphur and process principles therein. Black-Right-Pointing-Pointer The need for research in this area was identified. Black-Right-Pointing-Pointer We perform thermodynamic modelling of the fluid bed stage. Black-Right-Pointing-Pointer Initial findings indicate the prominence of solid phase sulphur. - Abstract: Gasification of solid waste for energy has significant potential given an abundant feed supply and strong policy drivers. Nonetheless, significant ambiguities in the knowledge base are apparent. Consequently this study investigates sulphur mechanisms within a novel two stage fluid bed-plasma gasification process. This paper includes a detailed review of gasification and plasma fundamentals in relation to the specific process, along with insight on MSW based feedstock properties and sulphur pollutant therein. As a first step to understanding sulphur partitioning and speciation within the process, thermodynamic modelling of the fluid bed stage has been performed. Preliminary findings, supported by plant experience, indicate the prominence of solid phase sulphur species (as opposed to H{sub 2}S) - Na and K based species in particular. Work is underway to further investigate and validate this.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗