SEARCH · Search NASA
Results for “fuel combustion efficiency”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Effect of fuels on combustion efficiency of 5-inch ram-jet-type combustor
Explore the source record for details and available documents.
Hydrocarbon-fueled scramjet combustor component development tests
Technology is being developed for a hydrocarbon-fueled engine operating as a scramjet over the flight Mach number range from 5.6 to 7. A series of connected-pipe tests were performed to define scramjet combustor design criteria applicable to the United Technologies Research Center (UTRC) engine concept which comprises a pair of modular axisymmetric combustor underslung on a supersonic/hypersonic missile. The development of key pilot and fuel injector components of the combustor is pursued in a variable-geometry two-dimensional test section over a range of combustor entrance conditions simulating the intended flight regime. The applicability of the two-dimensional test results to the axisymmetric engine is ensured by maintaining a proper simulation of combustor entrance conditions and preserving the actual length scale in the two-dimensional test configuration. An air-breathing pilot was developed and tested to evaluate flame stabilization and flame propagation characteristics. A pilot configuration was developed that operated stably, with minimal flow spillage, at exhaust stagnation temperatures as high as 4500 R with ethylene fuel. It was demonstrated that the pilot promotes efficient combustion of either gaseous ethylene or preheated liquid Jet-A (JP-5) when they are injected into the supersonic mainstream flow as primary fuels. For the tests with Jet-A fuel, the fuel was heated in an array of internal cooling passages within the pilot walls to a thermodynamic condition such that it would flash-vaporize upon injection into the mainstream flow. The idea of using the air-breathing pilot and distributed primary and secondary fuel injectors to achieve efficient supersonic combustion over a wide range of equivalence ratios was also experimentally demonstrated during the program. During staged fuel injection tests with gaseous ethylene fuel, high secondary fuel combustion efficiencies were achieved and smooth transitions from fully supersonic to dual mode (supersonic/subsonic) operation were demonstrated at high overall equivalence ratios.
Fuel Flexible Combustion Systems for High-Efficiency Utilization of Opportunity Fuels in Gas Turbines
The purpose of this program was to develop low-emissions, efficient fuel-flexible combustion technology which enables operation of a given gas turbine on a wider range of opportunity fuels that lie outside of current natural gas-centered fuel specifications. The program encompasses a selection of important, representative fuels of opportunity for gas turbines with widely varying fundamental properties of combustion. The research program covers conceptual and detailed combustor design, fabrication, and testing of retrofitable and/or novel fuel-flexible gas turbine combustor hardware, specifically advanced fuel nozzle technology, at full-scale gas turbine combustor conditions. This project was performed over the period of October 2008 through September 2011 under Cooperative Agreement DE-FC26-08NT05868 for the U.S. Department of Energy/National Energy Technology Laboratory (USDOE/NETL) entitled "Fuel Flexible Combustion Systems for High-Efficiency Utilization of Opportunity Fuels in Gas Turbines". The overall objective of this program was met with great success. GE was able to successfully demonstrate the operability of two fuel-flexible combustion nozzles over a wide range of opportunity fuels at heavy-duty gas turbine conditions while meeting emissions goals. The GE MS6000B ("6B") gas turbine engine was chosen as the target platform for new fuel-flexible premixer development. Comprehensive conceptual design and analysis of new fuel-flexible premixing nozzles were undertaken. Gas turbine cycle models and detailed flow network models of the combustor provide the premixer conditions (temperature, pressure, pressure drops, velocities, and air flow splits) and illustrate the impact of widely varying fuel flow rates on the combustor. Detailed chemical kinetic mechanisms were employed to compare some fundamental combustion characteristics of the target fuels, including flame speeds and lean blow-out behavior. Perfectly premixed combustion experiments were conducted to provide experimental combustion data of our target fuels at gas turbine conditions. Based on an initial assessment of premixer design requirements and challenges, the most promising sub-scale premixer concepts were evaluated both experimentally and computationally. After comprehensive screening tests, two best performing concepts were scaled up for further development. High pressure single nozzle tests were performed with the scaled premixer concepts at target gas turbine conditions with opportunity fuels. Single-digit NOx emissions were demonstrated for syngas fuels. Plasma-assisted pilot technology was demonstrated to enhance ignition capability and provide additional flame stability margin to a standard premixing fuel nozzle. However, the impact of plasma on NOx emissions was observed to be unacceptable given the goals of this program and difficult to avoid.
Influence of Nozzle Design on the Basic Combustion-Chamber Characteristics in a Gas-Turbine Engine
Tests with nozzles of different types are conducted in a segment of a combustion chamber. The nozzle associated with the most efficient fuel combustion is identified. Tests of a complete combustion chamber in a gas-turbine engine are recommended.
Exploring the potential benefits of high-efficiency dual-fuel combustion on a heavy-duty multi-cylinder engine for SuperTruck I
In support of the Daimler SuperTruck I team’s 55% brake thermal efficiency (BTE) pathway goal, researchers at Oak Ridge National Laboratory performed an experimental investigation of the potential efficiency and emissions benefits of dual-fuel advanced combustion approaches on a modified heavy-duty 15-L Detroit™ DD15 engine. For this work, a natural gas port fuel injection system with an independent injection control for each cylinder was added to the DD15 engine. For the dual-fuel strategies investigated, 65%–90% of the total fuel energy was supplied through the added port fuel injection natural gas (NG) fueling system. The remaining fuel energy was supplied by one or more direct injections of diesel fuel using the production high pressure diesel fueling system. The production DD15 air handling system and combustion geometry were unmodified for this study. Efficiency and emissions with dual-fuel strategies including both low temperature combustion (LTC) and non-LTC approaches such as dual fuel direct-injection were investigated along with control authority over combustion phasing. Parametric studies of dual-fuel NG/diesel advanced combustion were conducted in order to experimentally investigate the potential of high-efficiency, dual-fuel combustion strategies to improve BTE in a multi-cylinder engine, understand the potential reductions in engine-out emissions, and characterize the range of combustion phasing controllability. Characterization of mode transitions from mixing-controlled diesel pilot ignition to kinetically controlled ignition is presented. Key findings from this study included a reproducible demonstration of BTE approaching 48% at up to a 13-bar brake mean effective pressure with significant reductions in engine-out NOx and soot emissions. Additional results from investigating load transients in dual-fuel mode and initial characterization of particle size distribution during dual-fuel operation are presented.
Comparison of combustion characteristics of ASTM A-1, propane, and natural-gas fuels in an annular turbojet combustor
The performance of an annular turbojet combustor using natural-gas fuel is compared with that obtained using ASTM A-1 and propane fuels. Propane gas was used to simulate operation with vaporized kerosene fuels. The results obtained at severe operating conditions and altitude relight conditions show that natural gas is inferior to both ASTM A-1 and propane fuels. Combustion efficiencies were significantly lower and combustor pressures for relight were higher with natural-gas fuel than with the other fuels. The inferior performance of natural gas is shown to be caused by the chemical stability of the methane molecule.
Effects of amorphous silica coating on cerium oxide nanoparticles induced pulmonary responses
Recently cerium compounds have been used in a variety of consumer products, including diesel fuel additives, to increase fuel combustion efficiency and decrease diesel soot emissions. However, cerium oxide (CeO{sub 2}) nanoparticles have been detected in the exhaust, which raises a health concern. Previous studies have shown that exposure of rats to nanoscale CeO{sub 2} by intratracheal instillation (IT) induces sustained pulmonary inflammation and fibrosis. In the present study, male Sprague–Dawley rats were exposed to CeO{sub 2} or CeO{sub 2} coated with a nano layer of amorphous SiO{sub 2} (aSiO{sub 2}/CeO{sub 2}) by a single IT and sacrificed at various times post-exposure to assess potential protective effects of the aSiO{sub 2} coating. The first acellular bronchoalveolar lavage (BAL) fluid and BAL cells were collected and analyzed from all exposed animals. At the low dose (0.15 mg/kg), CeO{sub 2} but not aSiO{sub 2}/CeO{sub 2} exposure induced inflammation. However, at the higher doses, both particles induced a dose-related inflammation, cytotoxicity, inflammatory cytokines, matrix metalloproteinase (MMP)-9, and tissue inhibitor of MMP at 1 day post-exposure. Morphological analysis of lung showed an increased inflammation, surfactant and collagen fibers after CeO{sub 2} (high dose at 3.5 mg/kg) treatment at 28 days post-exposure. aSiO{sub 2} coating significantly reduced CeO{sub 2}-induced inflammatory responses in the airspace and appeared to attenuate phospholipidosis and fibrosis. Energy dispersive X-ray spectroscopy analysis showed Ce and phosphorous (P) in all particle-exposed lungs, whereas Si was only detected in aSiO{sub 2}/CeO{sub 2}-exposed lungs up to 3 days after exposure, suggesting that aSiO{sub 2} dissolved off the CeO{sub 2} core, and some of the CeO{sub 2} was transformed to CePO{sub 4} with time. These results demonstrate that aSiO{sub 2} coating reduce CeO{sub 2}-induced inflammation, phospholipidosis and fibrosis. - Highlights: • Both CeO{sub 2} and aSiO{sub 2}/CeO{sub 2} particles were detected in the respective particle-exposed lungs. • The dissolution of aSiO{sub 2} coating from CeO{sub 2} particle core with time was demonstrated in the particle-exposed lungs. • aSiO{sub 2} coating significantly protected CeO{sub 2}-induced pulmonary inflammatory responses. • aSiO{sub 2} coating showed a protective effect on CeO{sub 2}-induced lung fibrosis.
Effect of operating conditions on the exhaust emissions from a gas turbine combustor
Exhaust concentrations of total unburned hydrocarbons, carbon monoxide, and nitric oxide were measured from a single J-57 combustor liner installed in a 30 diameter test section. Tests were conducted over a range of inlet total pressures from 1 to 20 atmospheres, inlet total temperatures from 310 to 590 K, reference velocities from 8 to m/sec, and fuel-air ratios from 0.004 to 0.015. Most of the data were obtained using ASTM A-1 fuel; however, a limited number of tests was performed with natural gas fuel. Combustion efficiency and emission levels are correlated with operating conditions. Sampling error at operating conditions for which combustion efficiency was below about 90 percent resulted in abnormally low readings for hydrocarbon emissions.
Phase I Final Scientific Report
Explore the source record for details and available documents.
Operation of internal combustion engine with improved fuel efficiency
A process of operating a spark-ignited internal combustion engine (SI-ICE) with improved fuel efficiency and reduced emissions including under steady state and under lean-operating conditions at high overall air to fuel (AFR) ratios. A first supply of high octane hydrocarbon fuel, such as gasoline or natural gas, and a first supply of oxidant are fed to a fuel reformer to produce a gaseous reformate with a reforming efficiency of greater than 75 percent relative to equilibrium. The gaseous reformate is mixed with a second supply of oxidant, after which the resulting reformate blended oxidant is fed with a second supply of high octane hydrocarbon fuel to the SI-ICE for combustion. Steady state fuel efficiency is improved by more than 3 percent, when the reformate comprises from greater than about 1 to less than about 18 percent of the total volume of reformate blended oxidant fed to the engine.
Carbonyl Formation during High Efficiency Clean Combustion of FACE Fuels
The low temperature conditions that occur during high efficiency clean combustion (HECC) often lead to the formation of partially oxidized HC species such as aldehydes, ketones and carboxylic acids. Using the diesel fuels specified by the Fuels for Advanced Combustion Engines (FACE) working group, carbonyl species were collected from the exhaust of a light duty diesel engine operating under HECC conditions. High pressure liquid chromatography - mass spectrometry (LC-MS) was used to speciate carbonyls as large as C 9 . A relationship between carbonyl species formed in the exhaust and fuel composition and properties was determined. Data were collected at the optimum fuel efficiency point for a typical road load condition. Results of the carbonyl analysis showed changes in formaldehyde and acetaldehyde formation, formation of higher molecular weight carbonyls and the formation of aromatic carbonyls. Details of these changes in carbonyl formation and discussion of formation mechanisms will be presented.
Reinforcement learning applied to dilute combustion control for increased fuel efficiency
To reduce the modeling burden for control of spark-ignition engines, reinforcement learning (RL) has been applied to solve the dilute combustion limit problem. Q-learning was used to identify an optimal control policy to adjust the fuel injection quantity in each combustion cycle. A physics-based model was used to determine the relevant states of the system used for training the control policy in a data-efficient manner. The cost function was chosen such that high cycle-to-cycle variability (CCV) at the dilute limit was minimized while maintaining stoichiometric combustion as much as possible. Experimental results demonstrated a reduction of CCV after the training period with slightly lean combustion, contributing to a net increase in fuel conversion efficiency of 1.33%. To ensure stoichiometric combustion for three-way catalyst compatibility, a second feedback loop based on an exhaust oxygen sensor was incorporated into the fuel quantity controller using a slow proportional-integral (PI) controller. The closed-loop experiments showed that both feedback loops can cooperate effectively, maintaining stoichiometric combustion while reducing combustion CCV and increasing fuel conversion efficiency by 1.09%. Finally, a modified cost function was proposed to ensure stoichiometric combustion with a single controller. In addition, the learning period was shortened by half to evaluate the RL algorithm performance on limited training time. Experimental results showed that the modified cost function could achieve the desired CCV targets, however, the learning time was reduced by half and the fuel conversion efficiency increased only by 0.30%.
A Low-Temperature, Solution Processable Tin Oxide Electron-Transporting Layer Prepared by the Dual-Fuel Combustion Method for Efficient Perovskite Solar Cells
Although tin oxide (SnO 2 ) has been employed recently as an efficient electron-transporter to realize highly efficient organometal halide perovskite solar cells (PVSCs), it is still quite challenging to apply it through facile solution-based synthesis at low enough temperature (<150 °C) to be compatible with the roll-to-roll printing on polymer substrates. In this work, a dual-fuel combustion method has been successfully adapted to modulate the exothermic characteristics and processing temperature (140 °C) of SnO 2 to achieve homogeneous and crystalline thin film as efficient electron-transporting layer for PVSCs. The fabricated SnO 2 film not only has high transparency (from 350 nm to near-infrared region) but also possesses good electron extraction ability, as evidenced by the efficient PL quenching in bilayered SnO 2 /CH 3 NH 3 PbI 3 film. By passivating SnO 2 surface with a C 60 -containing self-assembled monolayer (C 60 -SAM), a high power conversion efficiency (PCE max ) of >15% with negligible hysteresis can be achieved in PVSC. This demonstrates the great potential of applying this dual-fuel combustion process to improve processability and charge-transporting properties of metal oxides for organic electronics applications.
Performance gains by using heated natural-gas fuel in an annular turbojet combustor
A full-scale annular turbojet combustor was tested with natural gas fuel heated from ambient temperature to 800 K (980 F). In all tests, heating the fuel improved combustion efficiency. Two sets of gaseous fuel nozzles were tested. Combustion instabilities occurred with one set of nozzles at two conditions: one where the efficiency approached 100 percent with the heated fuel; the other where the efficiency was very poor with the unheated fuel. The second set of nozzles exhibited no combustion instability. Altitude relight tests with the second set showed that relight was improved and was achievable at essentially the same condition as blowout when the fuel temperature was 800 K (980 F).
The impact of fuel and injection strategy on combustion characteristics, emissions and efficiency in gasoline compression ignition operation
Gasoline compression ignition in diesel engines has been proposed in order to meet increasingly stringent emission regulations without sacrificing efficiency. In this study, a six-cylinder heavy-duty diesel engine was operated in a mixing controlled gasoline compression ignition mode to investigate the influence of fuels and injection strategies on the combustion characteristics, emissions, and thermal efficiencies. Fuels, including ethanol (E), isobutanol (IB), and diisobutylene (DIB), were blended with a gasoline fuel to form E10, E30, IB30, and DIB30 based on volumetric fraction. These four blends along with gasoline formed the five test fuels. With these fuels, three injections strategies were investigated, including late pilot injection, early pilot injection, and port fuel injection/direct injection. The impact of moderate exhaust gas recirculation on nitrogen oxides and soot emissions was examined to determine the most promising fuel/injection strategy for emissions reduction. In addition, first and second law analyses were performed to provide insights into the efficiency, loss, and exergy destruction of the various gasoline fuel blends at low and medium load conditions. Overall, the emission output, thermal efficiency, and combustion performances of the five fuels were found to be similar and their differences are modest under most test conditions. E30 with the port/direct fuel injection strategy obtained the peak brake thermal efficiency (46.9%) and gross indicated thermal efficiency (52.2%) at 14 bar. At 7 bar, the peak brake thermal efficiency (44.2%) and gross indicated thermal efficiency (52.5%) also belonged to E30 with the late pilot injection strategy. The second law analysis revealed that exergy destruction was mostly influenced by the fuel type and not by the injection strategy for the 14 bar operating conditions. However, the opposite trend was observed for the 7 bar case. In addition, port fuel injection in combination with oxygenated fuel blends was found to be helpful to suppress soot emissions for operation with exhaust gas recirculation.
"COMBUSTION DEVELOPMENT OF A HIGH EFFICIENCY DIESEL MICRO PILOT NATURAL GAS ENGINE."
Dual fuel engine operation with premixed natural gas as the main fuel and diesel pilot ignition has been gaining interest among research and industry as natural gas is among the most promising existing alternative fuels. The dual fuel engine performance has been shown to equal and sometimes, depending on operating conditions, better the performance and efficiency of the diesel engine. Along with its advantages on the combustion high efficiency, diesel-like performance, and emissions of NOx and particulate matter reduction, some disadvantages are brought by the application of such operation. At light load conditions, there is an increase in CO and HC emissions, low fuel efficiency and combustion stability. While operating at higher loads, the dual fuel engine performance showed to be limited by combustion knock. This effectively reduces the maximum break mean effective pressure (BMEP) the engine can output when compared to a diesel engine. Although combustion knock is well defined in SI and diesel engines, dual fuel knock characterization still needs more investigation. This project centers on developing a fuel system for a diesel engine conversion to dual fuel to deliver high load and high efficiency. The selected engine has been converted to the dual fuel operation and dual fuel combustion has been demonstrated. After achieving the project goal of a high load and high efficiency dual fuel engine, the combustion knock in dual fuel operation will be characterized and a method for detection and intensity calculation will be modeled. The characterization will also be compared to spark ignition (SI) and reactivity-controlled compression ignition (RCCI) operating engines.
Ground idle performance improvement of a double-annular combustor by using simulated variable combustor geometry
A test program was undertaken to determine if variable combustor geometry could be used to reduce exhaust emissions of a low-pressure-ratio jet engine operating at ground idle conditions. Three techniques for varying combustor geometry were simulated. Other techniques evaluated were radial fuel staging and the use of preheated fuel. When simulated variable combustor geometry was employed with radial fuel staging, combustion efficiency at a fuel-air ratio of 0.01 was increased from 77 to 95 percent, and exhaust emissions of unburned hydrocarbons and carbon monoxide were significantly reduced.