Search NASA⌕ Search

SEARCH · Search NASA

Results for “fumigation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

Fumigation of Alcohol in a Light Duty Automotive Diesel Engine

A light-duty automotive Diesel engine was fumigated with methanol in amounts up to 35% and 50% of the total fuel energy respectively in order to determine the effect of alcohol fumigation on engine performance at various operating conditons. Engine fuel efficiency, emissions, smoke, and the occurrence of severe knock were the parameters used to evaluate performance. Raw exhaust particulate and its soluble organic extract were screened for biological activity using the Ames Salmonella typhimurium assay. Results are given for a test matrix made up of twelve steady-state operating conditions. For all conditions except the 1/4 rack (light load) condition, modest thermal efficiency gains were noted upon ethanol fumigation. Methanol showed the same increase at 3/4 and full rack (high load) conditions. However, engine roughness or the occurrence of severe knock limited the maximum amount of alcohol that could be fumigated. Brake specific nitrogen oxide concentrations were found to decrease for all ethanol conditions tested. Oxides of nitrogen emissions, on a volume basis, decreased for all alcohol conditions tested. Based on the limited particulate data analyzed, it appears that ethanol fumigation, like methanol fumigation, while lowering the mass of particulated emitted, does enhance the biological activity of that particulate.

Broukhiyan, E. M. H.↗

Performance characteristics of a diesel engine using low- and medium-energy gases as a fuel supplement (fumigation)

The use of low- and medium-energy gases derived from solid waste is investigated. Gases that simulate those gases that could be derived from refuse were injected into the air inlet of a 298-kilowatt (400 horsepower) diesel engine as a fuel supplement. This process is called fumigation. Three different gases with thermal-energy contents of 6.11 MJ/cu m (164 Btu/cu ft), 18.1 MJ/cu m (485 Btu/cu ft), and 18.8 MJ/cu m (505 Btu/cu ft, respectively, were used at rates ranging as high as 20 percent of the normal fuel oil energy at four different engine load points. The test results indicated approximately 100 percent gas energy utilization with no observable deleterious effect on the engine.

Monford, L. G.↗

Performance and emissions characteristics of aqueous alcohol fumes in a DI diesel engine

A single cylinder DI Diesel engine was fumigated with ethanol and methanol in amounts up to 55% of the total fuel energy. The effects of aqueous alcohol fumigation on engine thermal efficiency, combustion intensity and gaseous exhaust emissions were determined. Assessment of changes in the biological activity of raw particulate and its soluble organic fraction were also made using the Salmonella typhimurium test. Alcohol fumigation improved thermal efficiency slightly at moderate and heavy loads, but increased ignition delay at all operating conditions. Carbon monoxide and unburned hydrocarbon emission generally increased with alcohol fumigation and showed no dependence on alcohol type or quality. Oxide of nitrogen emission showed a strong dependence on alcohol quality; relative emission levels decreased with increasing water content of the fumigant. Particulate mass loading rates were lower for ethanol fueled conditions. However, the biological activity of both the raw particulate and its soluble organic fraction was enhanced by ethanol fumigation at most operating conditions.

Heisey, J. B.↗

Spectral changes in conifers subjected to air pollution and water stress: Experimental studies

The roles of leaf anatomy, moisture and pigment content, and number of leaf layers on spectral reflectance in healthy, pollution-stressed, and water-stressed conifer needles were examined experimentally. Jeffrey pine (Pinus jeffreyi) and giant sequoia (Sequoiadendron gigantea) were exposed to ozone and acid mist treatments in fumigation chambers; red pine (Pinus resinosa) needles were artificially dried. Infrared reflectance from stacked needles rose with free water loss. In an air-drying experiment, cell volume reductions induced by loss of turgor caused near-infrared reflectance (TM band 4) to drop after most free water was lost. Under acid mist fumigation, stunting of tissue development similarly reduced band 4 reflectance. Both artificial drying and pollutant fumigation caused a blue shift of the red edge of spectral reflectance curves in conifers, attributable to chlorophyll denaturation. Thematic mapper band ratio 4/3 fell and 5/4 rose with increasing pollution stress on artificial drying. Loss of water by air-drying, freeze-drying, or oven-drying enhanced spectral features, due in part to greater scattering and reduced water absorption. Grinding of the leaf tissue further enhanced the spectral features by increasing reflecting surfaces and path length. In a leaf-stacking experiment, an asymptote in visible and infrared reflectance was reached at 7-8 needle layers of red pine.

Westman, Walter E.↗

The Effect of Entrainment Through Atmospheric Boundary Layer Growth on Observed and Modeled Surface Ozone in the Colorado Front Range

Ozone concentrations at the Earth's surface are controlled by meteorological and chemical processes and are a function of advection, entrainment, deposition, and net chemical production/loss. The relative contributions of these processes vary in time and space. Understanding the relative importance of these processes controlling surface ozone concentrations is an essential component for designing effective regulatory strategies. Here we focus on the diurnal cycle of entrainment through atmospheric boundary layer (ABL) growth in the Colorado Front Range. Aircraft soundings and surface observations collected in July/August 2014 during the DISCOVER-AQ/FRAPPÉ (Deriving Information on Surface conditions from Column and Vertically Resolved Observations Relevant to Air Quality/Front Range Air Pollution and Photochemistry Éxperiment) campaigns and equivalent data simulated by a regional chemical transport model are analyzed. Entrainment through ABL growth is most important in the early morning, fumigating the surface at a rate of ~5 ppbv/h. The fumigation effect weakens near noon and changes sign to become a small dilution effect in the afternoon on the order of -1 ppbv/h. The chemical transport model WRF-Chem (Weather Research and Forecasting Model with chemistry) underestimates ozone at all altitudes during this study on the order of 10-15 ppbv. The entrainment through ABL growth is overestimated by the model in the order of 0.6-0.8 ppbv/h. This results from differences in boundary layer growth in the morning and ozone concentration jump across the ABL top in the afternoon. This implicates stronger modeled fumigation in the morning and weaker modeled dilution after 11:00 LT.

Entrainment through ABL Growth↗

The chemistry of atmospheric bromine

Bromine may act as a catalyst for recombination of ozone and could be more efficient than either nitric oxide or chlorine. The lower atmosphere contains small concentrations of gaseous bromine produced in part by marine activity and volatilization of particulate material released during the combustion of leaded gasoline, with an additional contribution due to the use of methyl bromide as an agricultural fumigant. Observations by Lazrus et al., (1975) indicate small concentrations of bromine, about 10 to the -11th power (v/v), in the contemporary stratosphere and appear to imply a reduction of approximately 0.3% in the global budget of O3. Estimates are given for future reductions in O3 which might occur if the use of CH3Br as an agricultural fumigant were to continue to grow at present rates.

Wofsy, S. C.↗

Air pollutant production by algal cell cultures

The production of phytotoxic air pollutants by cultures of Chlorella vulgaris and Euglena gracilis is considered. Algal and plant culture systems, a fumigation system, and ethylene, ethane, cyanide, and nitrogen oxides assays are discussed. Bean, tobacco, mustard green, cantaloupe and wheat plants all showed injury when fumigated with algal gases for 4 hours. Only coleus plants showed any resistance to the gases. It is found that a closed or recycled air effluent system does not produce plant injury from algal air pollutants.

Fong, F.↗

Utilization of alternative fuels in diesel engines

Performance and emission data are collected for various candidate alternate fuels and compare these data to that for a certified petroleum based number two Diesel fuel oil. Results for methanol, ethanol, four vegetable oils, two shale derived oils, and two coal derived oils are reported. Alcohol fumigation does not appear to be a practical method for utilizing low combustion quality fuels in a Diesel engine. Alcohol fumigation enhances the bioactivity of the emitted exhaust particles. While it is possible to inject many synthetic fuels using the engine stock injection system, wholly acceptable performance is only obtained from a fuel whose specifications closely approach those of a finished petroleum based Diesel oil. This is illustrated by the contrast between the poor performance of the unupgraded coal derived fuel blends and the very good performance of the fully refined shale derived fuel.

Lestz, S. A.↗

An experimental study of the atmospheric boundary layer modified by a change in surface roughness and surface temperature

Turbulent flow, resembling an on-shore flow from the ocean crossing the beach at an oblique angle, is investigated. Measurements of this flow have been taken at high sample rates and include measurements at various heights, high enough to describe the portion of the mean wind and temperature profiles and fluxes that are of interest for the solution of practical engineering problems. These problems could include air pollution (fumigation and plume trapping), operation of low flying aircraft, crop-spraying and crop-dusting operations.

Tieleman, H. W.↗

Ignition and combustion: Low compression ratio, high output diesel

The feasibility of converting a spark ignition aircraft engine GTSI0-520 to compression ignition without increasing the peak combustion pressure of 1100 lbs/sq.in. was determined. The final contemplated utilized intake air heating at idle and light load and a compression ratio of about 10:1 with a small amount of fumigation (the addition of about 15% fuel into the combustion air before the cylinder). The engine used was a modification of a Continental-Teledyne gasoline engine cylinder from the GTSI0-520 supercharged aircraft engine.

Source record↗

Acid mist and ozone effects on the leaf chemistry of two western conifer species

The effects of ozone and acid-mist exposures on the leaf chemistry of Jeffrey pine and giant sequoia seedlings grown in filtered-air greenhouses were investigated. Acid-mist treatments (pH 4.1, 3.4, 2.7, or 2.0) were administered for 3 h, and ozone exposures (0, 0.10, and 0.20 microliter/liter), which followed acid-mist treatments, for 4 h, each for three days a week for six to nine weeks. It was found that seedlings were more susceptible to acid-mist and acid mist/ozone combinations, than to ozone alone. Acid mist treatment resulted in higher levels of nitrogen and sulfur (both present in acid mist) as well as Na. Leaves of giant sequoia exhibited increased K and decreased Mn, while Jeffrey pine showed increases in Fe and Mn. In sequoia leaves, concentrations of Ca, Mg, and Ba decreased. Acid treatment also reduced chlorophyll b concentrations in both conifer species. Extensive changes induced by acid mist are consistent with earlier observations of changes in spectral reflectance of conifer seedlings observed after three weeks of fumigation.

Westman, Walter E.↗

A Historical Perspective on Primary and Possible Secondary Sources of Atmospheric Carbon Tetrachloride

Atmospheric sources of Carbon Tetrachloride (CTC) have been controversial since its detection in the early 1970. Initial proposals were that it is globally uniformly distributed and its lack of current emissions and inferred lifetime indicated that it was likely of natural origin. Historical analysis of CTC use and emissions showed that atmospheric CTC was long-lived and mainly of man-made origin although small natural sources and sinks (e. g. oceans) could not be ruled out. This deduction was hard because a majority of emissions had occurred in early part of the 20th century when CTC was commonly used as a fumigant, a solvent, and a raw material for the manufacture of many chemicals. In the 1940's adverse health effects of exposure to CTC became evident and its emissions were greatly curtailed and substituted with C2Cl4 which was thought to be much safer. There were smog chamber studies that showed that C2Cl4, a widely used solvent during the late 20th century, could produce CTC with up to a 7% yield. Subsequently it was discovered that this chemistry probably required Cl atoms and since Cl atoms were not abundant in the atmosphere actual yields based on OH oxidation were probably closer to 0.1%. CTC was subsequently banned by the Montreal Protocol to prevent stratospheric ozone depletion and its preferred substitute C2Cl4 was also banned by EPA for reasons of potential carcinogenicity and toxicity. CTC since has been measured in many airborne NASA campaigns in which plumes have been sampled from a variety of regions which may still be emitting CTC. I will briefly discuss this historical perspective of CTC and show some recent data that may shed light on its current sources or lack there off.

atmosphere↗

The Effects of Plasma Application on Radish Seeds with Implications for Space Crop Production

In extended space missions, the astronaut diet will consist mostly of prepackaged foods. This could result in nutritional deficiencies due to the gradual breakdown of certain vitamins. To address this deficiency, fresh produce must be grown from seed during spaceflight. Stored seeds, however, can be vulnerable to microbial contamination which could jeopardize plant health and crop food safety. To alleviate this concern, the current practice is to sanitize seeds on the ground before spaceflight to the International Space Station (ISS). Methods of seed sanitization include alcohol soaking and chlorine gas fumigation, which have harmful effects on the environment and human health. Plasma application is a new sanitization approach that avoids these negative side effects while potentially elevating germination rate and improving growth rate; yet plasma application requires specific exposure time, power, and pressure to achieve these benefits. In the present study, Raphanus sativus ‘Cherry Belle’ radish seeds were exposed to either low pressure (Diener) plasma or atmospheric pressure plasma for varying increments of time (30s-1200s). Data collected includes immediate germination rate (viability) and microbial log reduction. Additionally, seeds were stored for later germination rate testing. Microbial assay controls have highlighted variability in initial microbial load between individual seeds, and further work is being performed to determine the standard microbial load of an untreated seed. In some samples, a negative log reduction was observed after plasma treatment encouraging further study to determine if the plasma is perforating the seed coat and releasing endophytic microbes. Treatment with Diener plasma shows promising microbial log reduction, but lower viability. In contrast, treatment with atmospheric pressure plasma offers high viability, but poor microbial log reduction. Further study will aim at determining whether plasma treatment is effective at not only sanitization, but sterilization. This research was funded by a NASA grant at the Kennedy Space Center.

Plasma↗

The Effects of Plasma Application on Radish Seeds with Implications for Space Crop Production

In extended space missions, the astronaut diet will consist mostly of prepackaged foods. This could result in nutritional deficiencies due to the gradual breakdown of certain vitamins. To address this deficiency, fresh produce must be grown from seed during spaceflight. Stored seeds, however, can be vulnerable to microbial contamination which could jeopardize plant health and crop food safety. To alleviate this concern, the current practice is to sanitize seeds on the ground before spaceflight to the International Space Station (ISS). Methods of seed sanitization include alcohol soaking and chlorine gas fumigation, which have harmful effects on the environment and human health. Plasma application is a new sanitization approach that avoids these negative side effects while potentially elevating germination rate and improving growth rate; yet plasma application requires specific exposure time, power, and pressure to achieve these benefits. In the present study, Raphanus sativus ‘Cherry Belle’ radish seeds were exposed to either low pressure (Diener) plasma or atmospheric pressure plasma for varying increments of time (30s-1200s). Data collected includes immediate germination rate (viability) and microbial log reduction. Additionally, seeds were stored for later germination rate testing. Microbial assay controls have highlighted variability in initial microbial load between individual seeds, and further work is being performed to determine the standard microbial load of an untreated seed. In some samples, a negative log reduction was observed after plasma treatment encouraging further study to determine if the plasma is perforating the seed coat and releasing endophytic microbes. Treatment with Diener plasma shows promising microbial log reduction, but lower viability. In contrast, treatment with atmospheric pressure plasma offers high viability, but poor microbial log reduction. Further study will aim at determining whether plasma treatment is effective at not only sanitization, but sterilization. This research was funded by a NASA grant at the Kennedy Space Center.

Space Crop Production↗