SEARCH · Search NASA

Results for “generative flow model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

All sources NASA NTRS DOE OSTI

NASA NTRS2020

Simulation and Modeling of Flow Generated by Gust Generator in a Wind Tunnel

A computational study of a gust field generated by a gust generator in a low-speed wind tunnel. The gust generator is designed for the University of Washington Aeronautical Laboratory (UWAL) Kirsten wind tunnel for a gust load alleviation (GLA) control experiment of a Common Research Model (CRM) flexible wing utilizing the Variable Camber Continuous Trailing Edge Flap (VCCTEF). The gust generator comprises four horizontal NACA 0015 gust generator vanes placed upstream of the test section. Computational fluid dynamics simulations using a two-dimensional (2D) Unsteady-Reynolds-Averaged-Navier-Stokes (URANS) with k-ω Shear Stress Transport (SST) turbulence model provide detailed time-resolved information about the generated flow by the gust generator under prescribed sinusoidal motion. The characteristics of the induced flow by the gust generator are analyzed. A gust propagation model of the gust field is investigated. An unsteady lift model is developed using a varying-fidelity approach which includes a 2D interference aerodynamic model of the combined gust generator-wing system. The computed integrated unsteady lift is compared to experimental data for validation of the unsteady lift model. Both the amplitude and transport delay are found to be accurately captured by the unsteady lift model.

Nhan, Nguyen↗

NASA NTRS1990

One- and two-dimensional Stirling machine simulation using experimentally generated flow turbulence models

Investigations of one- and two-dimensional (1- or 2-D) simulations of Stirling machines centered around experimental data generated by the U. of Minnesota Mechanical Engineering Test Rig (METR) are covered. This rig was used to investigate oscillating flows about a zero mean with emphasis on laminar/turbulent flow transitions in tubes. The Space Power Demonstrator Engine (SPDE) and in particular, its heater, were the subjects of the simulations. The heater was treated as a 1- or 2-D entity in an otherwise 1-D system. The 2-D flow effects impacted the transient flow predictions in the heater itself but did not have a major impact on overall system performance. Information propagation effects may be a significant issue in the simulation (if not the performance) of high-frequency, high-pressure Stirling machines. This was investigated further by comparing a simulation against an experimentally validated analytic solution for the fluid dynamics of a transmission line. The applicability of the pressure-linking algorithm for compressible flows may be limited by characteristic number (defined as flow path information traverses per cycle); this warrants further study. Lastly the METR was simulated in 1- and 2-D. A two-parameter k-w foldback function turbulence model was developed and tested against a limited set of METR experimental data.

Goldberg, Louis F.↗

NASA NTRS1986

Application of a computational model for vortex generators in subsonic internal flows

A model for the analysis of vortex generators in a fully viscous subsonic internal flow is evaluated. A vorticity source term is used in a modified form of the Parabolized Navier-Stokes equations to model the shed vortex. Computed results are compared with idealized flow vortex paths, and with experimental data for vortex generators embedded in a thick turbulent boundary layer. The analysis is also compared with experimental data for a separated diffusing S-duct and for a diffusing S-duct with vortex generators. Quantitative comparisons are shown for the latter three cases. Emphasis is placed on verifying the ability of the model to predict global distortions in the flow field.

Kunik, W. G.↗

NASA NTRS1986

Application of a computational model for vortex generators in subsonic internal flows

Kunik, W. G.↗

NASA NTRS1995

A Combined Geometric Approach for Computational Fluid Dynamics on Dynamic Grids

A combined geometric approach for computational fluid dynamics is presented for the analysis of unsteady flow about mechanisms in which its components are in moderate relative motion. For a CFD analysis, the total dynamics problem involves the dynamics of the aspects of geometry modeling, grid generation, and flow modeling. The interrelationships between these three aspects allow for a more natural formulation of the problem and the sharing of information which can be advantageous to the computation of the dynamics. The approach is applied to planar geometries with the use of an efficient multi-block, structured grid generation method to compute unsteady, two-dimensional and axisymmetric flow. The applications presented include the computation of the unsteady, inviscid flow about a hinged-flap with flap deflections and a high-speed inlet with centerbody motion as part of the unstart / restart operation.

Slater, John W.↗

NASA NTRS1986

Transonic, turbulent boundary-layer separation generated on an axisymmetric flow model

Experimental data describing the transonic, turbulent, separated flow generated by an axisymmetric flow model are presented. The model consisted of a circular-arc bump affixed to a straight, circular cylinder aligned with the flow direction. Measurements of the mean velocity, turbulence intensity, and Reynolds shear-stress profiles were made in the separated flow. These data revealed dramatic changes in the shear-stress levels as the flow passed through the interaction to reattachment. Behavior of the turbulence reaction to the imposed pressure gradients was examined in terms of the mixing length and the excursions of the turbulence from equilibrium.

Bachalo, W. D.↗

NASA NTRS1979

An investigation of transonic turbulent boundary layer separation generated on an axisymmetric flow model

Experimental data are presented describing the transonic turbulent separated flow generated by an axisymmetric flow model. The model consisted of a circular-arc bump affixed to a straight circular cylinder aligned with the flow direction. Measurements of the mean velocity, turbulence intensity, and Reynolds shear stress profiles were made in the separated flow. These data revealed the dramatic changes in the shear stress levels as the flow passed from the interaction through to reattachment. Information on the behavior of the turbulence reaction to the imposed pressure gradients, as presented in this investigation, will be required for the development of the turbulence models used in predicting nonequilibrium turbulent flow fields.

Bachalo, W. D.↗

NASA NTRS1995

A source-sink model of the generation of plate tectonics from non-Newtonian mantle flow

A model of mantle convection which generates plate tectonics requires strain rate- or stress-dependent rheology in order to produce strong platelike flows with weak margins as well as strike-slip deformation and plate spin (i.e., toroidal motion). Here, we employ a simple model of source-sink driven surface flow to determine the form of such a rheology that is appropriate for Earth's present-day plate motions. In this model, lithospheric motion is treated as shallow layer flow driven by sources and sinks which correspond to spreading centers and subduction zones, respectively. Two plate motion models are used to derive the source sink field. As originally implied in the simpler Cartesian version of this model, the classical power law rheologies do not generate platelike flows as well as the hypothetical Whitehead-Gans stick-slip rheology (which incorporates a simple self-lubrication mechanism). None of the fluid rheologies examined, however, produce more than approximately 60% of the original maximum shear. For either plate model, the viscosity fields produced by the power law rheologies are diffuse, and the viscosity lows over strike-slip shear zones or pseudo-margins are not as small as over the prescribed convergent-divergent margins. In contrast, the stick-slip rheology generates very platelike viscosity fields, with sharp gradients at the plate boundaries, and margins with almost uniformly low viscosity. Power law rheologies with high viscosity contrasts, however, lead to almost equally favorable comparisons, though these also yield the least platelike viscosity fields. This implies that the magnitude of toroidal flow and platelike strength distributions are not necessarily related and thus may present independent constraints on the determination of a self-consistent plate-mantle rheology.

Bercovici, David↗

NASA NTRS1994

Simultaneous three-dimensional velocity and mixing measurements by use of laser Doppler velocimetry and fluorescence probes in a water tunnel

A water tunnel investigation was conducted to demonstrate the capabilities of a laser-based instrument that can measure velocity and fluorescence intensity simultaneously. Fluorescence intensity of an excited fluorescent dye is directly related to concentration level and is used to indicate the extent of mixing in flow. This instrument is a three-dimensional laser Doppler velocimeter (LDV) in combination with a fluorometer for measuring fluorescence intensity variations. This capability allows simultaneous flow measurements of the three orthogonal velocity components and mixing within the same region. Two different flows which were generated by two models were studied: a generic nonaxisymmetric nozzle propulsion simulation model with an auxiliary internal water source that generated a jet flow and an axisymmetric forebody model with a circular sector strake that generated a vortex flow. The off-body flow fields around these models were investigated in the Langley 16- by 24-Inch Water Tunnel. The experimental results were used to calculate 17 quantities that included mean and fluctuating velocities, Reynolds stresses, mean and fluctuating dye fluorescence intensities (proportional to concentration), and fluctuating velocity and dye concentration correlations. An uncertainty analysis was performed to establish confidence levels in the experimental results. In general, uncertainties in mean velocities varied between 1 and 7 percent of free-stream velocity; uncertainties in fluctuating velocities varied between 1 and 5 percent of reference values. The results show characteristics that are unique to each type of flow.

Neuhart, Dan H.↗

NASA NTRS2022

Measurement of Surface Deformation Related to the December 2018 Mt. Etna Eruption Using Time-Series Interferometry and Magma Modeling for Hazard Zone Mapping

Mount Etna has erupted several times since it was first formed. Recently, Mount Etna began erupting again over 24–27 December 2018. Because it erupts frequently, Mount Etna should be observed on a frequent basis. From June 2018 to October 2019, 34 and 56 interferometric synthetic aperture radar (InSAR) images were acquired from the ascending and descending tracks of the Sentinel-1 satellite, respectively. We employed the Stanford Method for Persistent Scatterers (StaMPS) and a refined small baseline subset (SBAS) InSAR method to produce a surface deformation time-series map. In the time-series analysis, the phase signal remained unaltered with time. The Okada model was then applied to the result to generate a modeled interferogram, and the Q-LavHA program was run to generate a lava flow prediction model. A direct comparison of the results showed that Persistent Scatterers Interferometry (PSI)-StaMPS and the refined SBAS technique were comparable in terms of the displacement pattern, with slightly different velocity values obtained for individual points. In particular, a velocity range of −25 to 21 cm/yr was obtained from PSI-StaMPS, whereas a range of −30 to 25 cm/yr was obtained from the refined SBAS method. Upon computation of the vertical and east-west displacement components based on ascending and descending track data using both methods, deformation velocities of 51.5 and 52.5 cm/yr in the westerly direction on the western flank of Mount Etna were obtained from PSI-StaMPS and the refined SBAS method, respectively, whereas on the eastern flank, deformation toward the east was estimated to occur at a velocity of 50.1 or 54.2 cm/yr, respectively. PSIStaMPS estimated a vertical deformation velocity of −5.3 to 18.3 cm/yr, whereas the refined SBAS method produced a velocity range of approximately −7 to 19 cm/yr. The interferogram obtained via Okada modeling showed two fault sources in the 2018 Mount Etna eruption and a total volume change of approximately 12.39 × 10 6 m 3 . From the modeling results, a lava flow prediction model was generated using the Q-LavHA program. The approaches described in this study can be used by government officials, authorities, and other decision-makers to monitor and assess the risk of volcanic activity in the region.

Suci Ramayanti↗

NASA NTRS1969

Spoiler-generated flow noise. II.

Analytical model of spoiler generated sound in jet pipe, presenting data on level, spectrum and directivity of sound

Gordon, C. G.↗

NASA NTRS1981

Factors which influence the behavior of turbofan forced mixer nozzles

A finite difference procedure was used to compute the mixing for three experimentally tested mixer geometries. Good agreement was obtained between analysis and experiment when the mechanisms responsible for secondary flow generation were properly modeled. Vorticity generation due to flow turning and vorticity generated within the centerbody lobe passage were found to be important. Results are presented for two different temperature ratios between fan and core streams and for two different free stream turbulence levels. It was concluded that the dominant mechanisms in turbofan mixers is associated with the secondary flows arising within the lobe region and their development within the mixing section.

Anderson, B. H.↗

NASA NTRS1981

Factors which influence the behavior of turbofan forced mixer nozzles

A finite difference procedure was used to compute the mixing for three experimentally tested mixer geometries. Good agreement was obtained between analysis and experiment when the mechanisms responsible for secondary flow generation were properly modeled. Vorticity generation due to flow turning and vorticity generated within the centerbody-lobe passage were found to be important. Results are presented for two different temperature ratios between fan and core streams and for two different free-stream turbulence levels. It was concluded that the dominant mechanisms in turbofan mixers is associated with the secondary flows arising within the lobe region and their development within the mixing section.

Anderson, B. H.↗

NASA NTRS1991

Symmetry plane model for turbulent flows with vortex generators

An approximate procedure is proposed for predicting the performance of counterrotating vortex-generator installations in incompressible flow. An inviscid calculation that includes the motion of the vortices is used to obtain crossflow velocities at the boundary-layer edge as a function of initial position, spacing, and strength of the vortices, and local values of the spanwise gradient are then folded into an integral turbulent-boundary layer procedure applied in the plane of symmetry. Special attention is paid to the consistency of the approximations and equations used. The two-dimensional aerodynamics of vortex generator installations on a NACA 0016 airfoil at angle-of-attack are estimated in this manner, and the results compared with experiments carried out with a 30-cm chord wing mounted in a 2.4 x 3.6-m cross-section wind tunnel and tested at chord Reynolds numbers of 0.7 and 1.4 x 10 to the 6th. Agreement in the separation location is found for these complex flows for a range of conditions.

Arnaud, Gilles L.↗

NASA NTRS1994

Three Dimensional Compressible Turbulent Flow Computations for a Diffusing S-Duct With/Without Vortex Generators

Numerical investigations on a diffusing S-duct with/without vortex generators and a straight duct with vortex generators are presented. The investigation consists of solving the full three-dimensional unsteady compressible mass averaged Navier-Stokes equations. An implicit finite volume lower-upper time marching code (RPLUS3D) has been employed and modified. A three-dimensional Baldwin-Lomax turbulence model has been modified in conjunction with the flow physics. A model for the analysis of vortex generators in a fully viscous subsonic internal flow is evaluated. A vortical structure for modeling the shed vortex is used as a source term in the computation domain. The injected vortex paths in the straight duct are compared with the analysis by two kinds of prediction models. The flow structure by the vortex generators are investigated along the duct. Computed results of the flow in a circular diffusing S-duct provide an understanding of the flow structure within a typical engine inlet system. These are compared with the experimental wall static-pressure, static- and total-pressure field, and secondary velocity profiles. Additionally, boundary layer thickness, skin friction values, and velocity profiles in wall coordinates are presented. In order to investigate the effect of vortex generators, various vortex strengths are examined in this study. The total-pressure recovery and distortion coefficients are obtained at the exit of the S-duct. The numerical results clearly depict the interaction between the low velocity flow by the flow separation and the injected vortices.

Cho, Soo-Yong↗

NASA NTRS1990

Chaotic, subduction-like downflows in a spherical model of convection in the earth's mantle

Model calculations are described for a compressible fluid in a three-dimensional spherical shell with 80 percent of the surface heat flow generated within the model mantle. The numerical solutions are strongly chaotic, with surface planforms dominated by long curvilinear downflows reminiscent of the descending slabs in the earth's mantle. The results suggest that descending slabs play an important part in driving mantle convection, and that their chaotic evolution may influence the spatial and temporal behavior of plates and thus the dispersal and aggregation of continents.

Glatzmaier, Gary A.↗

NASA NTRS1985

Effect of Steady-State Temperature Distortion on Inlet Flow to a High-Bypass-Ratio Turbofan Engine

The effects of circumferential inlet temperature distortion on the flow characteristics between a distortion generator and a high bypass ratio turbofan engine and through its compression system were evaluated to support the effort to generate analytical models. The flow characteristics are defined by the inlet duct, the flow angles, and the total temperature, total pressure, and static pressure profiles in the inlet duct and through the fan and compressor. The effects of Reynolds number, rotor speed, and distortion extent are also considered.

Soeder, R. H.↗

NASA NTRS1992

Grid generation research at OSU

In the last two years, effort was concentrated on: (1) surface modeling; (2) surface grid generation; and (3) 3-D flow space grid generation. The surface modeling shares the same objectives as the surface modeling in computer aided design (CAD), so software available in CAD can in principle be used for solid modeling. Unfortunately, however, the CAD software cannot be easily used in practice for grid generation purposes, because they are not designed to provide appropriate data base for grid generation. Therefore, we started developing a generalized surface modeling software from scratch, that provides the data base for the surface grid generation. Generating surface grid is an important step in generating a 3-D space for flow space. To generate a surface grid on a given surface representation, we developed a unique algorithm that works on any non-smooth surfaces. Once the surface grid is generated, a 3-D space can be generated. For this purpose, we also developed a new algorithm, which is a hybrid of the hyperbolic and the elliptic grid generation methods. With this hybrid method, orthogonality of the grid near the solid boundary can be easily achieved without introducing empirical fudge factors. Work to develop 2-D and 3-D grids for turbomachinery blade geometries was performed, and as an extension of this research we are planning to develop an adaptive grid procedure with an interactive grid environment.

Nakamura, S.↗