SEARCH · Search NASA
Results for “glasses”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Testing of High S Matrix Glasses to Expand DFHLW Glass Compositional Ranges (Rev.1)
Gaps in glass composition-property data for direct-feed high-level waste (DFHLW) have recently been identified. One such gap is the region of high sulfur solubility since previous, pretreated, high-level wastes contained very little sulfur. Filling this data gap will significantly broaden the range of process flowsheet options including minimal washing and will allow for optimized waste loading in DFHLW glasses. This report summarizes the data collected during the characterization of the DFHLW High S Glass Matrix (HS24). A glass matrix of 50 glass compositions was developed to evenly cover the DFHLW composition region for high sulfur glass. Matrix glasses were designed to expand the composition region outside the current component concentration and property limits so as to reduce uncertainties at the limits. The 50 matrix glasses were fabricated and tested for properties important to the success of DFHLW vitrification including: compositions, canister centerline cooling (CCC) crystallinity and isothermal crystallinity, density, viscosity, electrical conductivity (EC), product consistency test (PCT) response, toxicity, and sulfate solubility. Melter materials corrosion testing is reported elsewhere. These glasses were intentionally designed to have high SO 3 solubilities (0.7 to 2.2 SO 3 wt%) in compositional regions that had not been previously explored. Forty-eight glasses showed the measured SO 3 content retained >80% of the target SO 3 and the densities of all the glasses ranged from 2.49 g·cm -3 to 2.74 g·cm -3 . While the model predicted nepheline formation in 5 glasses, one of the tested 50 CCC glasses formed nepheline, and 35 glasses formed Cr-containing phases such as spinels and eskolaite. Only five glasses were amorphous after CCC treatment where 44 glasses with detectable crystals contained =10 wt% crystals and only one glass had > 10 wt% crystals. None of the glasses exceeded the allowable T 2% for spinel crystal formation at 950 ºC (i.e., no glasses had >2 wt% spinel at 950 ºC) during isothermal crystal fraction tests where 10 glasses showed no crystalline phases at or below 950 ºC. All the glasses (except one which failed being slightly lower than the target) satisfied the SO 3 constraint while 98 glasses did not meet the viscosity constraints and 4 failed the EC constraints. Six quenched (Q) and six CCC glasses failed the Defense Waste Processing Facility (DWPF) Environmental Assessment (EA) glass PCT threshold and 3 Q and 4 CCC failed the PCT design constraint. One glass exceeded the WTP delisting limits for Cr via EPA Method 1311 (i.e., Toxicity Characteristic Leaching Procedure, TCLP). It should be emphasized that some of these glasses were specifically designed to approach or even exceed certain property constraints, as filling data gaps in these regions will provide the greatest benefit for future model development by improving accuracy and reducing uncertainties. These insights will ultimately support the development of more robust glass formulation strategies, enabling higher waste loading, reducing operational risks, and expanding the processing envelope.
Application of the immobilized low-activity waste glass corrosion model to the static dissolution of 24 statistically-designed alkali-borosilicate waste glasses
Glass corrosion models that capture the complex mechanisms of the glass-water reaction enable the prediction of nuclear waste glass durability in disposal scenarios. Parameterization of such models is challenging because of the need to capture changes in corrosion behavior with time, reaction conditions, and glass composition. In this report we describe and employ the immobilized low activity waste (ILAW) glass corrosion model (IGCM) in geochemical simulations of static dissolution tests, at two temperatures (40 °C and 90 °C), for a matrix of 24 enhanced low activity waste (eLAW) glasses statistically designed to cover a processable composition space defined by 8 major glass components (Al 2 O 3 , B 2 O 3 , CaO, Na 2 O, SiO 2 , SnO 2 , ZrO 2 , and Others as defined in the text). The IGCM includes a first-order chemical affinity term and an ion-exchange term that represents the net exchange of Na+ ions in the pristine glass with protons in aqueous solution. Constant, time-dependent, and time- and pH-dependent functional forms of the ion-exchange term are evaluated to reproduce the change in corrosion behavior with time in saturated, static dissolution tests. The agreement with measured aqueous concentrations of the main glass components (B, Na, and Si) improved significantly upon addition of a time-dependent term, which therefore constitutes a simple representation of the glass-water reaction progress. Due to the limited changes in pH in the static dissolution tests, past a short initial period of rapid increase, addition of a pH dependent term did not appreciably improve the fits, indicating that comprehensive model parameterization requires more than one type of glass corrosion test to capture a wide range of solution chemistries. IGCM parameters were found to be dependent on glass composition, and the parameter sets generated in this work will enable the development of composition–parameter correlation models that offer the promise of predicting IGCM parameters, and thus glass corrosion behavior, solely based on glass composition.
Corrosion Testing of Refractory inContact with Molten Glasses Designed for Waste Vitrification - VSL Touchpoint Matrix Glasses
It is known that the predictive life of the refractory ceramic liner of nuclear waste glass melters is conservative, as demonstrated by performance of these materials such as in the Defense Waste Processing Facility (DWPF). The motivation for this task is to maximize the useful life of the melters that will be operated at the Waste Treatment and Immobilization Plant (WTP), which will in turn minimize procurement and disposal costs and melter outage times, as well as to identify maximum loadings in the waste glass of those species that corrode melter components. This task was initiated jointly with Pacific Northwest National Laboratory (PNNL) with the objective to develop a methodology and model to enable more accurate prediction of refractory service life under prototypic conditions from laboratory-scale material corrosion tests. Refractory corrosion is generally reported as physical material loss, measured in units of distance (e.g., inch) or as physical material loss rate, measured in units of distance per time (e.g., inch/day). In post-operational melters, the refractory corrosion is measured directly, sometimes reported as corrosion depth. Crucible tests are used in the laboratory to accelerate the refractory corrosion to facilitate a meaningful measurement in a commensurate amount of time. Crucible tests are particularly useful in understanding refractory corrosion across a large glass composition space, where operational testing would be prohibitive. Some of the critical parameters that are known to influence refractory corrosion by molten glass in a crucible test are temperature, system redox, molten salt phases, glass chemistry, and test duration. The majority of data collected for Monofrax® K-3 (hereafter referred to as K-3) corrosion is from crucible tests, but a small amount comes directly from scaled and production melters. Crucible test data has been collected under varying conditions, whereas data collected from operational melters is relatively fewer and represents conditions specific to the melter campaign. The result is that the published data can be grouped and analyzed in multiple ways, not all of which are readily comparable. The Standard Test Method for Isothermal Corrosion Resistance of Refractories to Molten Glass (ASTM C621) outlines the general guidelines used across industry. That method describes a sealed, static test in which the surface area of the refractory coupon and the volume of glass are fixed. A significant portion of the crucible data pertaining to nuclear waste glasses has been collected in a modified configuration; the most notable differences being the surface area of the refractory coupon to volume of the glass and use of a method for bubbling the melt. To our knowledge, the influence of those parameters on the refractory corrosion has not been quantified. In this work, it was determined that static tests and bubbled tests would be performed. Savannah River National Laboratory (SRNL) was tasked with setting up and performing static testing while PNNL was tasked with setting up and performing bubbled testing. Initial activities were performed to establish laboratory methods that reproduce data comparable to existing data sets of K-3 refractory corrosion by low activity waste (LAW) and high-level waste (HLW) glass compositions. Later activities were focused on refining the test parameters to establish a standard test practice to be used between Laboratories and collecting additional data to be used in the enhanced waste glass model development. This document serves primarily to convey the refractory loss measurement results from corrosion testing of K-3 refractory with waste glass compositions developed for use in the WTP melters. The data will be used in the enhanced property/composition models being developed for waste glass vitrification and melter operations.
Evaluation of GlassNet for physics-informed machine learning of glass stability and glass-forming ability
Glassy materials form the basis of many modern applications, including nuclear waste immobilization, touch-screen displays, and optical fibers, and also hold great potential for future medical and environmental applications. However, their structural complexity and large composition space make design and optimization challenging for certain applications. Of particular importance for glass processing and design is an estimate of a given composition's glass-forming ability (GFA). However, there remain many open questions regarding the underlying physical mechanisms of glass formation, especially in oxide glasses. It is apparent that a proxy for GFA would be highly useful in glass processing and design, but identifying such a surrogate property has proven itself to be difficult. While glass stability (GS) parameters have historically been used as a GFA surrogate, recent research has demonstrated that most of these parameters are not accurate predictors of the GFA of oxide glasses. Here, in this work, we explore the application of an open-source pre-trained neural network model, GlassNet, that can predict the characteristic temperatures necessary to compute GS with reasonable performance and assess the feasibility of using these physics-informed machine learning (PIML)-predicted GS parameters to estimate GFA. In doing so, we track the uncertainties at each step of the computation—from the original ML prediction errors to the compounding of errors during GS estimation, and finally to the final estimation of GFA. While GlassNet exhibits reasonable accuracy on all individual properties, we observe a large compounding of error in the combination of these individual predictions for the PIML prediction of GS, finding that random forest models offer similar accuracy to GlassNet. We also break down the performance of GlassNet on different glass families and find that the error in GS prediction is correlated with the error in crystallization peak temperature prediction. Lastly, we utilize this finding to assess the relationship between top-performing GS parameters and GFA for two ternary glass systems: sodium borosilicate and sodium iron phosphate glasses. We conclude that to obtain true ML predictive capability of GFA, significantly more data needs to be collected.
Structure–property relations of sodium iron phosphate nuclear waste glasses: Effects of iron redox ratio and glass composition
Iron phosphate glasses, known for their exceptional chemical durability and potential applicability in nuclear waste management, have gained significant attention over the years. The structures of these glasses are complicated by the coexistence of Fe 3+ and Fe 2+ , which plays a crucial role in determining their structures and properties. Here, this work uses molecular dynamics simulations to study the structural changes in Na 2 O–Fe 2 O 3 –P 2 O 5 glasses with varying glass composition and Fe 2+ /Fe 3+ redox ratio. It was found that the redox ratio and modifier contents significantly affected the short-range and medium-range orders in the glasses. Significant changes in the local environments around P 5+ and Fe 3+ were observed, as reflected by the bond distances and coordination numbers. Na + cations are found to preferentially associate with Fe 3+ (rather than Fe 2+ ), whereas Fe 2+ has stronger association with P 5+ than Na + , confirming the structural role of Fe 2+ as a glass modifier. The disruptions in P–O–P linkages upon increasing FeO suggest that FeO causes glass depolymerization. These glasses achieved higher connectivity with increasing Fe 3+ / (Fe 3+ + Fe 2+ ) ratios, conerting phosphorous Q 2 to Q 3 units and iron Q 5 units to Q 4 units. The decrease of nonbridging oxygen fractions with increasing Fe 3+ / (Fe 3+ + Fe 2+ ) ratios, through creating P–O–Fe linkages, is the main reason of enhanced network connectivity. Quantitative structure–property relationship analyses with different structural descriptors were used to correlate with measured properties. The analyses provided valuable insights into structure–property relationships, emphasizing the importance of choosing relevant energy parameters and defining glass network connectivity, particularly in F net descriptors. It was found the Fe–O–P linkage density exhibits strong correlations to measured dissolution rates, supporting the importance of these linkages in improving the chemical durability in iron phosphate glasses.
Durability testing of actual Hanford waste glasses and their non-radioactive simulant glasses
The low-activity waste (LAW) fraction of Hanford tank waste will be converted to glass at the Waste Treatment and Immobilization Plant (WTP) and disposed on the Hanford site. The chemical durability of LAW glasses has been researched for decades to satisfy contract requirements. Most LAW glass durability data has been generated on non-radioactive simulant glasses fabricated via crucible melts. These non-radioactive glasses were chosen due to safety and cost reasons with confidence that radioactive waste glasses would exhibit similar behavior. To reduce the risk of significant differences in laboratory test response data between WTP melter waste glass and simulant glass, Product Consistency Tests (PCT, i.e., ASTM C1285-21) and Environmental Protection Agency (EPA) 1313 durability tests were performed on actual and simulant LAW glasses fabricated using laboratory-scaled melters. Actual and simulant glass durability test results are presented and statistically compared. Finally, differences in test responses were found to be within experimental uncertainty.
Glass Design Using Machine Learning Property Models with Prediction Uncertainties: Nuclear Waste Glass Formulation
The United States Department of Energy is responsible for managing the legacy nuclear waste stored in underground tanks at the Hanford Site. The waste will be separately vitrified as low-activity waste and high-level waste fractions. Waste glass formulation algorithms have been traditionally developed using partial quadratic mixture property-composition models. Recently, machine learning (ML) techniques have been used to predict glass properties and discover new glass materials for nuclear waste vitrification, and these advancements can be utilized to improve waste glass composition design. In this proof-of-principle study, ML algorithms such as Gaussian process regression (GPR) were used to interpolate glass properties (e.g., viscosity, electrical conductivity, chemical durability). After selecting appropriate sets of GPR hyper-parameters for each property, an optimization program was developed to formulate glass compositions to maximize waste loading while simultaneously satisfying property within constraints. The results of the ML-based waste loadings and glass compositions were compared to those obtained using the traditional methods. Comparing to the previous glass design framework, the ML-based optimization methods offer improved glass designs and a streamlined approach to generation of optimally designed data and near real-time updates.
Origin of the Apollo 15 very low Ti green glass. A perspective from the compositional diversity in the very low Ti glasses
The very low Ti green glasses from the Apollo 15 site have intrigued scientists for over 20 years. Their primitive composition has been used to understand magmatic processes and the structure of the moon. The compositional variability observed in the Apollo 15 glass population has long been a point of debate. Initial studies did not recognize the compositional diversity in the glasses. Stolper et al. documented the major element variability and concluded it could not be produced by magmatic processes and therefore concluded that these glasses must be of impact origin. Subsequent studies confirmed a volcanic origin for the glass population and attempted to elucidate magmatic processes to account for its compositional variability. Models that have been proposed for these glasses include the following: (1) the crystallization of single or multiple phases (olivine, pyroxene, Fe metal, immiscible sulfide); (2) the incompatible behavior of Ni and Co during multiple phase crystallization at extremely low fO2; and (3) magma or source mixing. All of these models have problems. Type (1) models appear not to be consistent with recent trace element studies on the glasses; model (2) is dependent on the debatable incompatible behavior of Ni and Co, and, in models of type (3), the origin and nature of mixing models are somewhat unconstrained. This study compares the Apollo 15 green glasses with the very low Ti picritic glasses from other landing sites.
Deformation, Stress Relaxation, and Crystallization of Lithium Silicate Glass Fibers Below the Glass Transition Temperature
The deformation and crystallization of Li(sub 2)O (center dot) 2SiO2 and Li(sub 2)O (center dot) 1.6SiO2 glass fibers subjected to a bending stress were measured as a function of time over the temperature range -50 to -150 C below the glass transition temperature (Tg). The glass fibers can be permanently deformed at temperatures about 100 C below T (sub)g, and they crystallize significantly at temperatures close to, but below T,, about 150 C lower than the onset temperature for crystallization for these glasses in the no-stress condition. The crystallization was found to occur only on the surface of the glass fibers with no detectable difference in the extent of crystallization in tensile and compressive stress regions. The relaxation mechanism for fiber deformation can be best described by a stretched exponential (Kohlrausch-Williams-Watt (KWW) approximation), rather than a single exponential model.The activation energy for stress relaxation, Es, for the glass fibers ranges between 175 and 195 kJ/mol, which is considerably smaller than the activation energy for viscous flow, E, (about 400 kJ/mol) near T, for these glasses at normal, stress-free condition. It is suspected that a viscosity relaxation mechanism could be responsible for permanent deformation and crystallization of the glass fibers below T,
Effect of glass forming additives on low-activity waste feed conversion to glass
A significant effort was invested in the past to develop and refine mathematical models that relate the composition of nuclear waste glasses with their properties, such as viscosity, electrical conductivity, or chemical durability. However, less attention has been paid to the formulation of the melter feed itself, such as the chemical form and the particle size of the glass forming and modifying additives (GFMA), which have a significant effect on the feed-to-glass conversion process during melting. To address this issue, we systematically changed the mineral composition of a simulated low-activity waste melter feed and inspected its melting behavior. When substituting minerals with corresponding oxides and hydroxides, we found that different alumina sources (kyanite, gibbsite, boehmite, or corundum) had the strongest effect on the feed melting process, whereas the sources of Ca, Mg, and Zr had little effect. Further, the x-ray diffraction analysis showed that the alumina sources differ in their dissolution kinetics: early dissolving alumina sources, such as gibbsite (Al(OH) 3 ) and boehmite (AlO(OH)), increase the transient glass-forming melt viscosity at early stages, when gases still evolve, causing extended foaming, whereas alumina sources that dissolve at high temperatures, such as kyanite (Al 2 SiO 5 ) and corundum (Al 2 O 3 ), keep the transient glass-forming melt viscosity low and lead to a faster foam collapse. Using viscosity-composition relationship to estimate the viscosity of transient glass-forming melts in the primary foaming range, we found that the primary foam began to collapse at 360 to 800 Pa s, and fully collapsed between 65 and 260 Pa s. This result agrees with our previous studies, according to which the glass-forming melt viscosity at the cold cap foam bottom ranged from 24 to 85 Pa s.
Statistical generic design of glass and optimization: Selective review on oxide glasses
Designing a single glass composition for a multidimensional property space is challenging, and the difficulty increases with the number of design criteria. Traditionally, the task is accomplished using multiple statistical models that describe the relationships between composition (C) and property (P) values, i.e., C-P models. Recently, the structure (S)-property (P) statistical modeling has emerged as a complementary approach. The S-P modeling approach has also been shown to be a preferred method for modeling glass properties, particularly when a small data set is available, such as in single-component studies, or when strong nonlinearities exist between composition and properties. The combined model package, C-S-P, implements the concept of generic glass design, i.e., designing glass for performance by first selecting a specific or optimized set of glass network structural groups using S-P models and then transferring the designed structures (genes) to a particular composition using C-S models. This article reviews a set of supporting cases from the previous C-S-P modeling studies of phosphate, silicate, and borosilicate glasses, which are relevant for many critical commercial applications. The methodology for developing the statistical C-S-P database is presented, enabling the application of P?S?C to achieve a generic glass design and optimization, targeting multiple design criteria for both performance and processing properties simultaneously.
Friction behavior of glass and metals in contact with glass in various environments
Sliding friction experiments have been conducted for heat-resistant glass and metals in contact with glass. These experiments were conducted in various environments including vacuum, moist air, dry air, octane, and stearic acid in hexadecane. Glass exhibited a higher friction force in moist air than it did in vacuum when in sliding contact with itself. The metals, aluminum, iron, and gold, all exhibited the same friction coefficient when sliding on glass in vacuum as glass sliding on glass. Gold-to-glass contacts were extremely sensitive to the environment despite the relative chemical inertness of gold.
Geochemistry of impact glasses from the K/T boundary in Haiti - Relation to smectites and a new type of glass
Detailed element analyses were carried out on 12 black and seven yellow glasses from the K/T boundary section at Beloc (Haiti), and of three samples from smectite mantles around black glasses. The results obtained for bulk black and yellow glasses show differences between these, confirming the results of Sigurdsson et al. (1991) and Izett (1991), and the results obtained on individual spherules and shards are in agreement with bulk data. The present data also demonstrate, for the first time, the existence of yellow glass samples with high CaO but low S contents, which might have formed by fusion of various proportions of carbonates and evaporites or carbonates alone. One of the black glasses was found to have higher than average SiO2 and K2O abundances but lower concentrations of all other major elements. This suggests the existence of a third glass type, named the high Si-K variety (HSi,K) glass.
Raman and Infrared Spectroscopy of Yttrium Aluminum Borate Glasses and Glass-ceramics
Raman spectra of glasses and glass-ceramics in the Y2O3-Al2O3-B2O3 system are reported. Glasses with B2O3 contents ranging from 40 to 60 mole percent were prepared by melting 20 g of the appropriate oxide or carbonate powders in alumina crucibles at 1400 C for 45 minutes. Subsequent heat treatments of the glasses at temperatures ranging from 600 to 800 C were performed in order to induce nucleation and crystallization. It was found that Na2CO3 added to the melt served as a nucleating agent and resulted in uniform bulk crystallization. The Raman spectra of the glasses are interpreted primarily in terms of vibrations of boron - oxygen structural groups. Comparison of the Raman spectra of the glass-ceramic samples with spectra of aluminate and borate crystalline materials reveal that these glasses crystallize primarily as yttrium aluminum borate, YAl3(BO3)4.
Sulfur prevails in coatings on glass droplets - Apollo 15 green and brown glasses and Apollo 17 orange and black /devitrified/ glasses
Explore the source record for details and available documents.
Viscosity of transient glass-forming melt and its relation to foaming during batch-to-glass conversion
Primary foam, which affects the heat transfer into the glass batch and the final glass quality, occurs when a sufficient quantity of transient glass-forming melt evolves with viscosity low enough to close the open porosity of the reacting glass batch. To better understand how the fraction of transient melt and its viscosity affect the primary foam temperature range, we determined, with x-ray diffraction, the fraction and composition of the transient glass-forming melt in a heated waste glass melter feed as a function of temperature. Then we prepared a set of transient melts that occurred within the foaming temperature interval and measured their viscosities with spindle and falling sphere viscometers. Further, the results agree with the Adam-Gibbs and VFT viscosity-composition models, even for transient melt compositions outside of the models compositional validity range. As silica and other refractory particles dissolved in the predominantly borate transient melt while temperature increased, viscosity increased from the initial value of ~500 Pa s at the onset of foaming (~650°C) to a maximum of ~770 Pa s when silica dissolution was almost complete (~700°C). As temperature increased further, transient melt viscosity decreased to ~220 Pa s (~850°C) when the primary foam collapsed.
Site‐selective fluorescence and spectroscopic properties of Yb‐doped lanthanum titanate glasses
Abstract Ytterbium‐doped lanthanum titanate glasses were prepared by levitation melting for the detailed characterization of the spectroscopic properties in the rare‐earth titanate glass host. Low‐temperature fluorescence spectroscopy reveals distinct site‐selectivity in both static and lifetime fluorescence measurements suggesting an absence of clustering as well as significant variation of local ytterbium environments. Typical site‐selectivity behavior of a shrinking Stark manifold with lower excitation energy is observed. At 77 K, both the mean emission frequency and the fluorescence lifetime initially increase as the excitation energy decreases from about 11100 to 10750 and then slightly decrease at lower excitation energy. Temperature‐dependent lifetime measurements between 77 and 420 K show a decreasing lifetime with increasing temperature and are well described by a two‐level thermal activation model. The temperature‐dependent fluorescence spectroscopy coupled with a room temperature white light absorption measurement allow the determination of the Stark energy levels of in lanthanum titanate glass as well as the calculation of the laser cross‐sections.