SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The following folders contain 3 friction experiments on Utah FORGE core material from depths of 6735 - 8533ft. The experiment conditions range from 100% relative humidity at room temperature to fluid-saturated at 110C. Experiments were done on both intact samples in a single-direct shear configuration, double-direct shear, and gouge.
Frictional sliding experiments were performed on saw-cut samples of laboratory-made polycrystalline water ice, prepared in the same way as the material used by Kirby et al. (1987) in ice deformation experiments. The data show that the maximum frictional stress is a function of the normal stress but is not measurably dependent on temperature or sliding rate over the ranges covered in these experiments (77-115 K and 0.0003-0.03 mm/s, respectively). The sliding behavior was invariably stick slip, with the sliding surfaces exhibiting only minor gouge development. In samples with anomalously low strength, a curious arrangement of densely packed short vertical fractures was observed. The results of these experiments were applied to a model of near-surface tectonic activity on Ganymede, one of Jupiter's icy moons. The results indicate that a global expansion on Ganymede of 3 linear percent will cause extensional movement on preexisting faults at depths to 7 + or - 3 km.
Laboratory shear tests were conducted on pulverized Sierra White granite (SWG) to investigate slip mechanisms in naturally occurring faults. Synthetic fault geometries were constructed by sandwiching fine grained SWG powder in between steel forcing blocks. For dry experiments, ~3.5 g of SWG powder was poured onto the face of the lower steel forcing block and leveled. For saturated experiments, enough fluid was added to the ~3.5 g of Sierra White granite powder to form a slurry. This slurry was applied to the lower forcing block and leveled. Inclined forcing blocks with 25.4 mm diameter and 35° faces, which were machined from ground steel rods with fine teeth on the faces, help to hold the gouge in place and prevent delamination at the interface. The top forcing block had a 2.03 mm centered hole to allow pore fluid access to the gouge. A fine steel mesh prevented back flow of the gouge into pore fluid lines. Samples were isolated from the confining medium using three layers of heat shrink polyolefin, as shown in Figure 1. The outer layer was shrunk over the o-rings on the end caps to form an impermeable seal, which was reinforced with steel tie wires on both sides of the o-rings. Hardened steel spacers and copper shim stock was placed between the steel forcing blocks and the end caps to preserve the parallelism of the Hastelloy wetted parts. For dry samples, the end caps were plugged, while the end caps for the saturated samples were connected to pore lines.
High-pressure and temperature deformation experiments interfaced with acoustic emission (AE) monitoring have been conducted to study transformational faulting in Mn 2 GeO 4 olivine, which transforms to the β phase, isostructural to wadsleyite. Metastable Mn 2 GeO 4 olivine exhibits a marked embrittlement behavior at temperatures between 800 and 1100 K, emitting numerous AEs. At each temperature, brittle deformation is characterized by a two-stage process: (1) a “preparation” stage with numerous diffusedly located low-magnitude AEs and large b values (>2), and (2) a failure stage where larger-magnitude AEs form a planar distribution with b values about 1. Microstructure analysis reveals extensive kink band development in olivine grains in the recovered samples. Kink band boundaries (KBBs), with a typical thickness of ∼100 nm, are filled with a nanometric β-Mn 2 GeO 4 “gouge”. A dense array of secondary shear localizations is often present within the kink bands, suggesting significant shear deformation therein. The combined observations suggest that faulting in metastable Mn 2 GeO 4 olivine is a self-similar process, from grain-scale to the sample-scale. Both observed embrittlement behavior and the microstructure of metastable Mn 2 GeO 4 olivine are essentially identical to those in Mg 2 GeO 4 olivine we have reported previously, indicating that the physical mechanism of faulting in metastable olivine is insensitive to the specific crystallographic structure of the high-pressure phase. The low b values (about 1) observed in the faulting process in our experiments are similar to those of deep focus earthquakes in cold subduction zones. Our observed mechanism explains deep focus seismicity in cold metastable mantle wedges, provided that the self-similarity assumption holds to geological scales.
Induced seismicity is one of the main risks for gigaton-scale geological storage of carbon dioxide (CO 2 ). Thus, passive seismic monitoring is often recommended as a necessary component of the monitoring systems for CO 2 storage projects, with a particular forcus on risk mitigation. We present the first field study, CO2CRC Otway Project Stage 3 (Victoria, Australia), where distributed acoustic sensing (DAS) enabled high-precision tracking of the induced seismicity triggered by a small CO 2 injection and also informed the reservoir models. In 610 days of passive seismic monitoring of the Stage 3 injection, we detected 17 microseismic events (maximum moment magnitude Mw 0.1) using five deep boreholes equipped with enhanced-sensitivity optical fiber. The DAS array has sensitivity sufficient for detection and location of induced events with M w ~ ₋2 in a monitoring borehole located up to 1500 m away. Thanks to the dense spatial sampling by the DAS, we were able to estimate the focal mechanisms for events with M w > ₋1.5; although the monitoring boreholes provided very limited angular coverage. The main cluster of the events has the same location and source mechanism as the one triggered by the previous CO 2 injection at the Otway Project site, Stage 2C. Surprizingly, the Stage 2C and Stage 3 events closely followed the actual movement of the CO 2 saturation plume front (not the pressure front), as observed using controlled-source reflection seismic images. The nature of the plume-fault interaction remains unclear, but some alteration of the fault gouge by CO 2 might be responsible for the faults’ reactivation by the pressure perturbation. Importantly, the seismogenic fault could not be identified in the seismic images and was only revealed by DAS observations, which also demonstrated the signature of fluid–rock interaction, that may control the CO 2 flow.