Search NASA⌕ Search

SEARCH · Search NASA

Results for “grout”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Flowable Cementitious Grouts for False Bottoms in Hanford Waste Tanks – 26085

Cementitious grouts with epoxy coatings are being evaluated as an approach to refurbish the bottom of waste tanks at the Hanford Site. This work studies four grout concept materials for this application, two grouts being from commercial vendors and two grouts based off formulations used to close reactors and tanks at the Savannah River Site. All the candidate grouts demonstrate flowability and pumpability at the 0.5 cu ft scale. The commercial vendor products demonstrate the best flow and have lower water/premix ratio and are less likely to have bleed, which would impact epoxy bonding to the grout. The commercial products also demonstrate increased compression strengths compared to the reactor closure grouts. Additional fresh and cured properties for all the grout formulations were similar. The grouts in the tank waste simulant without epoxy coating do not crack but show visual changes to the grout and the surrounding simulant solution, and simulant absorption into the grout. The grout/epoxy bond in ambient conditions has strengths of over 7 MPa and needs to be evaluated for simulant chemical durability. Overall, the results to date justify testing the flowability, pumpability, and placement of the grouts at larger, engineering scale and for further studies of the interactions between the grout and epoxy.

Valdes, Nicholas [Savannah River National Laborato↗
DOE OSTI2025

Water reactive polyurethane grouting for deep vadose zone contaminant immobilization

Contaminants in the deep vadose zone (DVZ) pose a long-term threat to groundwater, human health, and the environment. Polyurethane grouting is a type of chemical grouting that is potentially advantageous in immobilizing contaminants in DVZs. Polyurethane resin has low viscosity that makes it feasible to penetrate and fill the pore space between fine particles. Here, in this study a series of laboratory pressure grouting and leaching tests were conducted to simulate and assess the effectiveness of polyurethane grouting for immobilizing contaminants in DVZs. Soil with fine particles was prepared with 127 I (as iodide) that served as a non-radioactive surrogate for radioactive 129 I. After grouting and curing, leaching tests were used to measure and compare contaminant diffusivity and leachability index values. Additionally, changes in porosity and saturated hydraulic conductivity of grouted soil were measured. X-Ray Computer Tomography (XCT) results showed that the cured polyurethane was distributed nearly homogeneously and approximately half of the voids were filled with cured polyurethane. Grouting reduced the saturated hydraulic conductivity of soil by 37 %. The effective diffusivity decreased by more than 80 % as compared with the ungrouted soil. The leachability index of the grouted soil was 6.5; meeting the criteria established by the U.S. Nuclear Regulatory Commission (NRC) standard. The results obtained in this study provide a valuable assessment of polyurethane grouting for iodide immobilization in the DVZ and indicate this approach may be a viable method for contaminant remediation in DVZ soils.

Contaminant Diffusion↗
DOE OSTI2023

ETF Grout Expansion: Evaluation of MgO Additions and Struvite Precipitation Protocol for Potential Expansion

The ETF ammonia tolerant grout waste form was developed by the Vitreous State Laboratory (VSL) to stabilize ammonium and thereby prevent emission of ammonia vapor during solidification of an ammonium-rich, concentrated sulfate aqueous waste stream generated at the Hanford Effluent Treatment Facility (ETF). VSL did not observe expansion in samples prepared during the waste form development work. However, Savannah River National Laboratory (SRNL) personnel did encounter expansion, in some cases up to 20+ volume percent expansion in ETF grout samples while preforming work scope to evaluate compositional ranges for ETF brine and of the precipitation and solidification reagent. The work requests can be found in Washington River Protection Services (WRPS) Statement of Work (SOW), Requisitions #: 339922 Revisions 0 and 1, March 11, 2021, and November 2021. Additional evaluation was requested by WRPS SOW Requisitions #: 356730, Revision 1, February 1, 2022, to determine whether differences in the slags or differences in sample preparation protocols used by VSL and SRNL were the cause of the expansion observed in the SRNL samples. G. Chen, WRPS, arranged a materials exchange between VSL and SRNL and coordinated the VSL protocol for grouting and curing 1L of Base Case ETF simulant. Materials were exchanged between VSL and SRNL and both laboratories performed the VSL struvite precipitation-solidification protocol and cured samples for at least 28 days. VSL and SRNL encountered expansion, at varying degrees, in all samples prepared under the material exchange and grouting protocol. Additional material exchange testing between VSL and SRNL and alternative materials evaluation to further investigate the causes of grout expansion and differentiate the effects of various dry materials, grouting procedures, and curing containers was requested by WRPS SOW Requisitions #: 356730, Revision 2, January 10, 2023. Pacific Northwest National Laboratory (PNNL) assembled and distributed materials to both laboratories for testing. Observations from this study indicated variations in MgO additions, water-to-dry mix (dm) ratios and curing containers did not correlate to ETF ammonia grout expansion. In comparison to previous work, SRNL observed the addition rate of NaOH to be a potential factor for the final pH in the struvite precipitation step. In the current testing NaOH was added in bulk (5-10 mL at one time) during the precipitation step. The resulting pH was 7.57-9.15 which is slightly higher than pH observed at a slower addition rate. Additional testing is needed to identify the presence and/or struvite stability in high-pH struvite precipitant ETF ammonia grout samples. Therefore, based on current data, it is unknown if NaOH addition rate is the fundamental cause of grout expansion.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Summary of Developing a Hanford Grout Modeling Framework Initial Workshop

The “Development of the Hanford Grout Modeling Framework” project as part of the Network of National Laboratories for Environmental Management and Stewardship (NNLEMS) funding program is underway. An initial project team workshop was held in Richland, WA on June 4 and 5, 2024 with participants from PNNL, SRNL, SNL, WRPS and CRESP (VU and UCF). The workshop covered an overview of the current state of the art in grout modeling tools provided by the team. Based on a focus on liquid waste immobilization grout and encapsulation grout for solid wastes and tank closure grout at Hanford, the team identified preliminary conceptual models for these three applications which will be used to form the basis of the Hanford Grout Modeling Framework. The key processes that can drive mechanisms impacting the grout performance were identified for each test case. The programmatic plan was also identified with five core Themes being selected that will form the focus of the project. Within each theme, individual tasks for Year 1 were planned in support of the development of an updated Hanford Grout Modeling Framework. This report presents a summary of the information presented during the workshop.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1983

Antenna grout replacement system

An epoxy grout suitable for use in mounting and positioning bearing runner plates used in hydrostatic bearing assemblies for rotatably mounting large radio telescope structures to stationary support pedestals is described. The epoxy grout may be used in original mountings or may be used as part of a replacement system for repairing cavities in existing grout resulting from grout deterioration. The epoxy grout has a relatively short work life and cure time even in the presence of hydraulic oil. The epoxy grout cures without shrinking or sagging to form a grout which is sufficiently strong and durable to provide a grout especially well suited for use under the high pressure loading and close tolerance requirements of large hydrostatic bearing assemblies.

Mcclung, C. E.↗
DOE OSTI2023

Presence of aromatic-rich organic matter and its characterization in grout materials: Implications for radionuclide immobilization

Grout materials are commonly used to immobilize low-level radioactive waste. Organic moieties can be unintentionally present in common ingredients used to make these grout waste forms, which may result in the formation of organo-radionuclide species. These species can positively or negatively affect the immobilization efficiency. However, the presence of organic carbon compounds is rarely considered in models or characterized chemically. Here, we quantify the organic pool of grout formulations with and without slag, as well as the individual dry ingredients used to make the grout samples (ordinary Portland cement (OPC), slag and fly ash), including total organic carbon (TOC) and black carbon, followed by aromaticity evaluation and molecular characterization via Electro Spray Ionization Fourier-Transform Ion Cyclotron Resonance Mass Spectrometry (ESI-FTICRMS). All dry grout ingredients contained significant amounts of organic carbon, ranging from 550 mg/kg to 6250 mg/kg for the TOC pool, with an averaged abundance of 2933 ± 2537 mg/kg, of which 60 ± 29% was composed of black carbon. The significant abundance of a black carbon pool implies the presence of the aromatic-like compounds, which was further identified by both phosphate buffer-assisted aromaticity evaluation (e.g., >1000 mg-C/kg as aromatic-like carbon in the OPC) and dichloromethane (DCM) extraction with ESIFTICRMS analysis. Besides aromatic-like compounds, other organic moieties were also detected in the OPC, such as carboxyl-containing aliphatic molecules. While the organic compound only consists of minor fractions of the grout materials investigated, our observations of the presence of various radionuclide-binding organic moieties suggests the potential formation of organo-radionuclides, such as radioiodine, which might be present at lower molar concentrations than TOC. Here, evaluating the role of organic carbon complexation in controlling the disposed radionuclides, especially for those radionuclides with strong association with organic carbon, has important implications for the long-term immobilization of radioactive waste in grout systems.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Opportunities to Update the Model of Tank Closure Grout Aging (SRNL-STI-2012-00404) Based on Experimental Results by the Savannah River Ecology Laboratory

The purpose of this report was to review the results of experiments on evolution of tank grout pore fluids performed by the Savannah River Ecology Laboratory (SREL) and reported in Seaman et al. (2020) and highlight opportunities for updating the model of tank grout degradation presented in Denham and Millings (2012). The SREL experimental results validate some assumptions used in the 2012 grout degradation model and provide information useful for updating the model. All experiments on tank grout degradation have limitations because of reaction rates and the enormous disparity between duration of the experiments and the duration of the degradation of the real tank grout system. Given these limitations, the experimental results form the basis for several recommendations for updating the grout degradation model described in this report.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Evaluation of Degradation Mechanisms for Solid Secondary Waste Grout Waste Forms

The overall objective of this work is to provide defensibility for the long-term performance of grouted Hanford SSW streams when disposed in a near surface disposal facility, IDF, on the Hanford Site. Providing defensibly for the long-term performance of the grouted waste forms is consistent with the research and development activities identified in the Performance Assessment Maintenance Plan, (Westcott et al. 2019), that are necessary to address the assumptions made in the PA. Specifically, this work addresses two areas identified for further research and development activities in the plan: (1) “Evaluate ongoing research on transport characteristics of cementitious materials using accelerated tests to approximate the effects of aging/alteration/weathering”; and (2) “Evaluate ongoing research on microbial effects on transport processes in cementitious materials.” The assembled subject matter expert team evaluated a list of degradation mechanisms and supporting processes and provided rankings of areas where further research and development (R&D) are needed. From this assessment, high priority R&D areas include: (1) the effects of carbonation, Ca leaching, and SSW dimensional change in grout waste forms; (2) updated model representations of grouted waste forms; and (3) scaled testing demonstrations. Moderate priority items including a paper study on possible microbial influence, reoxidation rates, radionuclide/contaminant dissolution from SSW in the grout and freeze thaw behavior. Other processes evaluated were either deemed unlikely to occur, to have little impact on the SSW waste forms, or to occur at time frames beyond those considered (>10,000 years). The assessments and proposed R&D approaches are expected to support an update to the WRPS SSW roadmap.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1981

Development of a polymetric grout for the hydrostatic bearing at DSS 14

Results of an investigation into the causes of the deterioration and premature failure of the grout under the hydrostatic bearing runner at DSS 14 are reported. Generic types of materials were screened and tested to find a grout material more resistive to the causes of grout failure. Emphasis was placed on the physical properties, strength, modulus of elasticity, and resistance to erosion and chemical attack by oil and unique requirements imposed by each material for mixing, placing, compacting, and cooling. The polymetric grout developed to replace the dry grout is described.

Mcclung, C. E.↗
DOE OSTI2022

ETF Grout Expansion: Effects of Different Slags and Struvite Precipitation Protocols (Stirring Time)

The ETF ammonia tolerant grout waste form was developed by the Vitreous State Laboratory (VSL) to stabilize ammonium and thereby prevent emission of ammonia vapor during solidification of an ammonium-rich, concentrated sodium sulfate aqueous waste stream generated at the Hanford Effluent Treatment Facility (ETF). VSL personnel did not observe expansion in samples prepared during the waste form development work. However, Savannah River National Laboratory (SRNL) personnel detected expansion, in a few ETF grout samples, up to ~ 20 percent vertical expansion, while preforming work scope to evaluate the effect of ETF brine compositional ranges on the precipitation and solidification processes. The initial work requests can be found in Washington River Protection Services (WRPS) Statement of Work (SOW, Requisitions #: 339922 Revisions 0 and 1, March 11, 2021, and November 2021, respectively. As a result of the waste form expansion observed by SRNL, additional evaluation was requested by WRPS SOW Requisitions #: 356730 Revision 0 and Revision 1, February 1, 2022, and July 11, 2022, respectively. The goal of these requests was to determine whether differences in the slags and / or in sample preparation protocols used by VSL and SRNL were the cause of the expansion observed in the SRNL samples. G. Chen, WRPS, arranged a materials exchange between VSL and SRNL and coordinated the VSL protocol(s) for grouting and curing 1L batches of Base Case ETF base case simulant. Materials were exchanged between VSL and SRNL. Both laboratories performed the VSL struvite precipitation-solidification protocol and cured samples for at least 28 days. Differences in VSL and SRNL slag compositions, mineralogy and particle size results in themselves or combined were determined to not be the cause of the expansion because all samples expanded regardless of whether the VSL or SRNL slags were used. The fundamental cause of the observed expansion could not be attributed to minor variations in the following: 1) chemistry of the slag and other reagents, 2) container wall thickness, 3) ambient bench top curing conditions at VSL and SRNL, 4) pH adjustments to 7 ± a few tenths of unit, nor 5) stirring time between the precipitation and solidification process steps. Additional observations include: grout samples prepared with VSL slag expanded less than those prepared with the SRNL slag and, based on a very limited sample set, some samples stirred for longer times expanded less than those stirred for 20 minutes.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Evaluation of Expansion in ETF Grout Compositional Variants

In summary, the Base Case grout, Mix K, prepared according to the protocol provided (short stirring time after struvite precipitation of about 30 minutes) expanded when cured in a dry and damp sealed bag. Two variants, Mix M, 100 % slag in the dry mix, did not expand when prepared and cured under the same dry and damp conditions. Mix L, precipitated struvite removed, showed very slight expansion after curing 289 days for both dry and damp curing which was expressed as slight bulging at the bottom of the container. Mix N, 100 % dilution of the simulant, did not expand when cured under dry conditions or in a sealed container in damp conditions. However, a cylinder of Mix N cured in a container that was slit and taped back together did expand in damp conditions. This condition enabled the grout to be exposed to more moisture that the grout sample cured in the capped container and stored in the same zip top bag with the damp towel. This information is provided to support processing and containerization of the ETF ammonia grout.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Simulation of radiation damage via alpha decay in BFS:PC grouts using 4 He 2+ ion acceleration

The impact of alpha radiation on cements used to encapsulate intermediate-level waste (ILW) is not well understood. ILW wastes can contain high levels of alpha-emitting radionuclides, meaning that the grouts used to encapsulate them are exposed to significant ionising radiation. Thus, a damaged region could develop in the grout adjacent to the alpha-emitting species. This work attempted to recreate this behaviour through nonradioactive 4 He 2+ ion-accelerator experiments, which have not previously been applied to common encapsulation grouts. The influence of this irradiation on a slag-Portland cement was investigated at different ages via transmission electron microscopy energy-dispersive x-ray spectroscopy (TEM-EDX) and supporting techniques, to assess whether 4 He 2+ irradiation caused textural or chemical zonation. No significant changes in hydrate phases or textures were observed, other than minor variations associated with carbonation. This paper provides a proof of concept for using ion acceleration techniques on cements and furthers knowledge on their radiation response.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Component-In-Grout Model Implementation for the E-Area Low-Level Waste Facility's Performance Assessment

The component-in-grout (CIG) disposal units are below grade earthen trenches that contain grout encapsulated waste components. Components disposed of within the CIG segments consist of large radioactively contaminated equipment and smaller waste forms (e.g., B-25 boxes and SeaLand containers) to fill the space around and above the large equipment. In the 2022 revision of the E-Area Low-Level Waste Facility’s (ELLWF) performance assessment, groundwater radionuclide contaminant transport through the vadose zone will be modeled using the PORFLOW software package for nine existing CIG segments located within the Slit Trench (ST) 23 footprint - no additional CIG segments are planned for at this time. The nine CIG segments have been placed within two of the nominally 20-foot-wide by 656-foot-long ST segments and are surrounded by no less than 1 foot of grout on all sides and up to 4 feet of backfill material. The two most recently placed CIG segments have an additional reinforced concrete mat to improve structural stability.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS1984

Epoxy Grout With Silica Thickener

Grout cures quickly, even in presence of hydraulic oil. Grout is mixture of aggregate particles, finely-divided silica, epoxy resin, and triethylenetetramine curing agent, with mixture containing about 85 percent silica and aggregate particle sand 15 percent resin and curing agent. Silica is thickening agent and keeps grout from sagging.

Mcclung, C. E.↗
DOE OSTI2021

Ultra-High-Performance Grout for Encapsulation of HEPA Filters

Ultra-high-performance grout (UHPG) grout appears to be good candidate for solidification and encapsulation of waste containing 99 Tc and 129 I that benefits from low Dobs. The properties that make UHPG a good candidate for encapsulating HEPA filters would make it a good option for microencapsulating other solid secondary waste (SSW) such as granular activated carbon, silver mordenite, and ion exchange resins. Containers made of UHPG would also be good candidates for dry disposal of SSW due to its very low diffusivity which prevents contaminant migration.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Tank 50 Simulant Grout and Toxicity Characteristic Leaching Procedure (TCLP) Results for Methyl Mercury Waste Acceptance Criteria (WAC) Limit

Testing of simulated Tank 50 salt solution grout, spiked with methyl mercury (MeHg) and ionic mercury, used the Toxicity Characteristic Leaching Procedure (TCLP) to evaluate leaching performance with respect to Hg and the Waste Acceptance Criteria (WAC) limits for the Saltstone Production Facility (SPF). This report describes the test parameters for simulant preparation and confirmatory analysis, grout preparation, TCLP leach testing and subsequent leachate analyses. These scoping tests were designed to provide an initial evaluation of the effect of increased MeHg and ionic Hg on the TCLP and were requested by Savannah River Remediation LLC (SRR) through a Technical Assistance Request (TAR). It is expected that this preliminary testing will likely lead to future, more detailed, testing involving the mercury (Hg) WAC and Hg limits with respect to the Tank 50 TCLP for mercury. The TCLP concentrations for total Hg have approached 0.06 mg/L in recent years for Tank 50 radioactive solutions containing up to 105 mg/L of Hg in the form of ionic (Hg(I/II), elemental (Hg(0)) and organo-mercury such as MeHg. In discussions with SRR personnel, it was decided for this non-baseline work to target Hg spike concentrations, using predominately MeHg, in the range of 150 to 350 mg/L total Hg to investigate corresponding Hg TCLP leaching behaviors.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Characterization of Saltstone Grout Line Samples

During a prestart recirculation operation in the Saltstone Processing Facility (SPF), operations staff noticed hardened scaling falling into the hopper. As a result, SPF operators and Saltstone Engineering decided to postpone operation and conduct a process room hopper cleanout. During the cleanout effort personnel noted greater than normal buildup of damp solid material in the transfer line. A borescope investigation was conducted and confirmed buildup was present throughout the transfer line to the downstream valves. Savannah River National Laboratory personnel were asked to characterize the scale material and samples collected from the saltstone grout line and provide recommendations and/or further guidance as to whether additional corrosion testing is needed for useful equipment operating life information. Based on the samples characterized results, the plug material contained only the 60:40 slag:fly ash saltstone. Portland cement in the original 10:45:45 Portland cement:slag:fly ash mix may result in a less abrasive slurry compared to the 60:40 slag:fly ash mix because the slag is > 95 % crushed angular, sharp edged glass. Saltstone grout erosion and corrosion testing of A36 carbon steel is needed to determine if the 60:40 mix is more abrasive and corrosive for A36 carbon steel than the 10:45:45 mix.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Full Scale HEPA Filter Encapsulation in Ultra-High-Performance Grout - Proof of Concept

The Hanford Tank Waste Treatment and Immobilization Plant (WTP) currently being constructed to treat radioactive waste, includes vitrification facilities for both the high-level waste (HLW) and low activity waste (LAW) fractions. Operation of the WTP will produce contaminated high-efficiency particulate air filters (HEPA), as part of the solid secondary waste (SSW) stream. The HEPA filters receive off-gas from the vessel vent header and primary off-gas treatment system in LAW Facility and remove particulate contaminants including 99 Tc and 129 I salts. The current disposal method for HEPA filters is encapsulation in metal containers using cementitious material (CM) and disposal in the Integrated Disposal Facility (IDF). Results from the 2017 IDF Performance Assessment (PA) WRPS (2018) demonstrated that while compliance is maintained for the 1000 year compliance period mandated by DOE O 435.1 and its accompanying manual, release of constituents from the HEPA filters result in exceedance of the performance objective imposed as the groundwater regulatory limit at later times. For example, at about 1500 years post-closure, solid secondary waste (SSW), including HEPA filters is predicted to become a dominant contributor to 99 Tc release and over the 10,000-year sensitivity analysis period, SSW is the dominant contributor of 129 I release to the groundwater. The estimated release could potentially be reduced if the HEPA filters are not compacted and waste containers could be distributed throughout a large space, thereby diluting the contaminant release. Additionally, a better cementitious material could be used to encapsulate the HEPA filters. One alternative method for disposal of contaminated HEPA filters is encapsulation of the filters in ultra high-performance grout (UHPG). UHPG is a variation of ultra-high-performance concrete (UHPC) is commonly used in the prestressed concrete industry for large structural members. Recent studies of UHPG show it has excellent properties for containing radionuclides such as 99 Tc and 129 I Nichols and Kaplan (2021). This report presents the results of the first attempt to encapsulate a clean, full-size HEPA filter in UHPG and evaluate the effectiveness of the immobilization process and final waste form. A full-scale proof-of-concept simulated waste form was prepared by encapsulating a HEPA filter in a 110-gallon stainless steel (SS) drum using UHPG. A change from Type I/II PC to Type 1L PLC was made after American Rock Products informed the team that they would no longer be using Type I/II by the end of 2024 and the northwest was phasing out Type I/II PC overall. Type I/II PC used in previous studies of UHPG for encapsulation (Nichols and Kaplan 2021). After the UHPG was cured both the scaled mockup and the full-scale simulated waste forms were sectioned for visual examination. UHPG completely encapsulated the filters and bonded to the external surfaces of materials comprising the filters. No cracks were observed in the sectioned waste forms.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗