Search NASA⌕ Search

SEARCH · Search NASA

Results for “hard rock”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

Yield and Emplacement Depth Effects on Acoustic Signals from Buried Explosions in Hard Rock

Subterranean energy releases such as explosions and earthquakes may disturb the Earth-atmosphere interface, creating acoustic waves that can travel great distances. These waves provide a record of the ground motion directly above the event. The information they encode may provide critical insight into the depth and size of underground explosions, the sequence of events immediately before volcanic eruptions, and the magnitude of strong motion resulting from earthquakes. However, the effect of event size and burial depth on the resulting acoustic wave has not been explored in detail. The relationship between acoustic amplitude, frequency, and energy is investigated for a series of well-characterized underground chemical explosions in granite. Acoustic amplitude was found to vary linearly with explosive yield divided by emplacement depth. Peak acoustic frequency appears to be a function of explosive yield alone. The ratio of radiated acoustic energy to source energy had a relatively poor fit to yield, depth, and combinations thereof. These relationships suggest that acoustic analysis can be used to determine the size and depth of a buried explosion. The results presented here have particular relevance to the nuclear monitoring community, because depth is difficult to determine with seismic methods.

58 GEOSCIENCES↗

Smaller Footprint Drilling System for Deep and Hard Rock Environments; Feasibility of Ultra-High-Speed Diamond Drilling

The two phase program addresses long-term developments in deep well and hard rock drilling. TerraTek believes that significant improvements in drilling deep hard rock will be obtained by applying ultra-high rotational speeds (greater than 10,000 rpm). The work includes a feasibility of concept research effort aimed at development that will ultimately result in the ability to reliably drill 'faster and deeper' possibly with smaller, more mobile rigs. The principle focus is on demonstration testing of diamond bits rotating at speeds in excess of 10,000 rpm to achieve high rate of penetration (ROP) rock cutting with substantially lower inputs of energy and loads. The significance of the 'ultra-high rotary speed drilling system' is the ability to drill into rock at very low weights on bit and possibly lower energy levels. The drilling and coring industry today does not practice this technology. The highest rotary speed systems in oil field and mining drilling and coring today run less than 10,000 rpm - usually well below 5,000 rpm. This document provides the progress through two phases of the program entitled 'Smaller Footprint Drilling System for Deep and Hard Rock Environments: Feasibility of Ultra-High-Speed Diamond Drilling' for the period starting 30 June 2003 and concluding 31 March 2009. The accomplishments of Phases 1 and 2 are summarized as follows: (1) TerraTek reviewed applicable literature and documentation and convened a project kick-off meeting with Industry Advisors in attendance (see Black and Judzis); (2) TerraTek designed and planned Phase I bench scale experiments (See Black and Judzis). Improvements were made to the loading mechanism and the rotational speed monitoring instrumentation. New drill bit designs were developed to provided a more consistent product with consistent performance. A test matrix for the final core bit testing program was completed; (3) TerraTek concluded small-scale cutting performance tests; (4) Analysis of Phase 1 data indicated that there is decreased specific energy as the rotational speed increases; (5) Technology transfer, as part of Phase 1, was accomplished with technical presentations to the industry (see Judzis, Boucher, McCammon, and Black); (6) TerraTek prepared a design concept for the high speed drilling test stand, which was planned around the proposed high speed mud motor concept. Alternative drives for the test stand were explored; a high speed hydraulic motor concept was finally used; (7) The high speed system was modified to accommodate larger drill bits than originally planned; (8) Prototype mud turbine motors and the high speed test stand were used to drive the drill bits at high speed; (9) Three different rock types were used during the testing: Sierra White granite, Crab Orchard sandstone, and Colton sandstone. The drill bits used included diamond impregnated bits, a polycrystalline diamond compact (PDC) bit, a thermally stable PDC (TSP) bit, and a hybrid TSP and natural diamond bit; and (10) The drill bits were run at rotary speeds up to 5500 rpm and weight on bit (WOB) to 8000 lbf. During Phase 2, the ROP as measured in depth of cut per bit revolution generally increased with increased WOB. The performance was mixed with increased rotary speed, with the depth cut with the impregnated drill bit generally increasing and the TSP and hybrid TSP drill bits generally decreasing. The ROP in ft/hr generally increased with all bits with increased WOB and rotary speed. The mechanical specific energy generally improved (decreased) with increased WOB and was mixed with increased rotary speed.

02 PETROLEUM↗

A Physical Basis for M s -Yield Scaling in Hard Rock and Implications for Late-Time Damage of the Source Medium

Surface wave magnitude M s for a compilation of 72 nuclear tests detonated in hard rock media for which yields and burial depths have been reported in the literature is shown to scale with yield W as a + b × log[W], where a = 2.50 ± 0.08 and b = 0.80 ± 0.05. While the exponent b is consistent with an M s scaling model for fully coupled, normal containment-depth explosions, the intercept a is offset 0.45 magnitude units lower than the model. The cause of offset is important to understand in terms of the explosion source. Hard rock explosions conducted in extensional and compressional stress regimes show similar offsets, an indication that the tectonic setting in which an explosion occurs plays no role causing the offset. The scaling model accounts for the effects of source medium material properties on the generation of 20-s period Rayleigh wave amplitudes. Aided by thorough characterizations of the explosion and tectonic release sources, an extensive analysis of the 1963 October 26 Shoal nuclear test detonated in granite 27 miles southeast of Fallon NV shows that the offset is consistent with the predictions of a material damage source model related to non-linear stress wave interactions with the free surface. This source emits Rayleigh waves with polarity opposite to waves emitted by the explosion. The Shoal results were extended to analyse surface waves from the 1962 February 15 Hardhat nuclear test, the 1988 September 14 Soviet Joint Verification Experiment, and the anomalous 1979 August 18 northeast Balapan explosion which exhibits opposite polarity, azimuth-independent source component U1 compared to an explosion. Modelling these tests shows that Rayleigh wave amplitudes generated by the damage source are nearly as large as or larger than amplitudes from the explosion. As such, destructive interference can be drastic, introducing metastable conditions due to the sensitivity of reduced amplitudes to Rayleigh wave initial phase angles of the explosion and damage sources. This meta-stability is a likely source of scatter in M s -yield scaling observations. The agreement of observed scaling exponent b with the model suggests that the damage source strength does not vary much with yield, in contrast to explosions conducted in weak media where Ms scaling rates are greater than the model predicts, and the yield dependence of the damage source strength is significant. This difference in scaling behaviour is a consequence of source medium material properties.

58 GEOSCIENCES↗

The Effects of Plasma Pre-Cracking on Drilling of Hard Rocks: A Single Insert Cutting Experiment

Abstract This paper studies the effects of plasma-induced cracks on rock cutting to support the concept of a plasma-integrated drag bit for accelerated geothermal drilling through hard rocks. For this, a single polycrystalline diamond compact (PDC) drilling technique is used in cutting granite to compare thrust and cutting forces between plasma-treated and untreated rock samples. The cracks are produced using underwater plasma at 80 J per pulse. This energy level does not produce visible damage to the rock. The cutting tests are conducted at a cutting speed of 12.7 m/min and four feed rates of 0.127, 0.201, 0.267, and 0.414 mm/s to represent actual drilling scenarios. The results show a general trend of reduction in both thrust and cutting forces for these feed rates, but the magnitude of reduction highly depends on the feed rate. The maximum force reduction of around 50% is found at the 0.267 mm/s feed rate with statistical significance. Cases with a higher force reduction are also found to have rougher surface topography, which indicates more excessive fracturing and, thus, a cracks-accelerated material removal process. This study provides initial evidence of using underwater plasma to increase the downhole drilling rate of hard rocks.

Engineering↗

Fluid effects on seismic waves in hard rocks with fractures and in soft granular media

When fractures in otherwise hard rocks are filled with fluids (oil, gas, water, CO{sub 2}), the type and physical state of the fluid (liquid or gas) can make a large difference in the wave speeds and attenuation properties of seismic waves. The present work summarizes methods of deconstructing theses effects of fractures, together with any fluids contained within them, on wave propagation as observed in reflection seismic data. Additional studies of waves in fluid-saturated granular media show that the behavior can be quite different from that for fractured media, since these materials are typically much softer mechanically than are the fractured rocks (i.e., having a very small drained moduli). Important fluid effects in such media are often governed as much by fluid viscosity as by fluid bulk modulus.

54 ENVIRONMENTAL SCIENCES↗

Drilling of Hard Rock by Means of Polycrystalline Diamond Inserts

A specialized measurement unit is developed to determine the basic parameters in the drilling of hard rock by bits with polycrystalline diamond inserts. The unit permits the collection of information and its wireless transfer to a computer.

36 MATERIALS SCIENCE↗

Hard Rock Drilling Optimization Software

The main objective of the developed software is to reduce the cost per foot during drilling, in other words, optimize the drilling operational parameters in achieving optimum ROP while avoiding critical operational parameters due to either low ROP, drillstring vibration, accelerated cutter wear, or low MSE. The developed software can also be used for post-well analysis to provide insight and lessons learned for future drilling operations. Several functions are available in the software to help the user perform drilling analysis, optimization, and simulation.

15 GEOTHERMAL ENERGY↗

The role of Aspo Hard Rock laboratory for the Swedish nuclear fuel and waste management's research, developing and demonstration programme for a final repository of spent nuclear fuel - 15378

The Aspo Hard Rock Laboratory (HRL), located in the Simpevarp area in the municipality of Oskarshamn in Sweden, Figure 1, constitutes an important part of the Swedish Nuclear Fuel and Waste Management (SKB) work with design and construction of a deep geological repository for final disposal of spent nuclear fuel. One of the fundamental reasons behind SKB's decision to construct an underground laboratory was to create an opportunity for research, development and demonstration in a realistic and undisturbed rock environment down to repository depth. Most of the research has concerned with processes of importance for the long-term safety of a future final repository and the capability to model the processes taking place at repository depth. Demonstration addresses the performance of the engineered barriers and practical means of constructing a repository and emplacing the canisters containing spent fuel. SKB will in the coming years more focus on using the Aspo HRL for demonstrating technology for and function of important parts of the repository system before constructing and operate the spent nuclear fuel repository in Forsmark. Aspo HRL includes both a research village with office space for 100 persons and different laboratories, e.g. Chemistry and Material Science Laboratory and Bentonite Laboratory, and an underground research laboratory to a depth of 460 m. The Aspo HRL is also open for other organisations to be used for their own projects and experiments not only related to nuclear waste management research. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

On various mechanisms of shear wave generation from underground chemical explosions in hard rocks

Significant shear waves observed during underground explosions can make them look similar to natural earthquakes. In the near field, they can be caused by the source geometry and emplacement conditions, heterogeneous and anisotropic properties of the rock mass, relaxation of a non-uniform in situ stress around the source after the departure of the shock wave as well as by activation of nearby faults. Here, the stress relaxation mechanism is important at depth when the difference in main principal stresses becomes significant. Another mechanism of shear motion generation is due to explosive gas flow from the source cavity into the cracks initiated by the shock wave and joints connected to the cavity. Also, the shock wave from the explosion can cause weakening of the rock either due to permanent damage or shock-induced liquefaction at saturated joints. Numerical modelling of underground chemical explosions in hard rock at various confinement stresses has been conducted to compare various mechanisms of shear wave generation and their seismic characteristics with that of a simple fault rupture process observed during an earthquake.

58 GEOSCIENCES↗

Experimental Investigation of Drillstring Torsional Vibration Effect on Rate of Penetration with PDC Bits in Hard Rock

Polycrystalline diamond compact (PDC) bits have shown tremendous performance compared to roller cone bits and have gained attraction in deep geothermal drilling applications. While PDC bits can reach a higher rate of penetration compared to other bits, they are more prone to drilling vibrations. The scope of this paper is to quantify the effects of drillstring torsional vibrations on PDC bit performance using a laboratory testing facility. Here, the tests were performed with three drillstring configurations to evaluate the effect of drillstring vibrations. The results showed that rigid testing overestimates the bit rate of penetration by 35% due to torsional vibrations.

15 GEOTHERMAL ENERGY↗

Characterization of Spall in Hard Rock from Observations and Simulations of the Source Physics Experiment Phase I

In this work, spall signals from the Source Physics Experiments are presented, analyzed, and modeled for insight to the explosion source. The observed signal is similar in nature to nearby historical nuclear explosions, and the surface force-time history or velocity can be interpreted with the same model. We use the models for peak spall velocity, spalled mass, and spall depth and radius derived from historical nuclear explosions to parameterize the physical force-time history model from Stump (1985) and show that this parameterized model can be used for spall prediction. The spall signal is also investigated with a numerical continuum model that incorporates gravity. Peak velocity and dwell time are well predicted, and the multiple slap-down phases are captured if one includes a weak near-surface layer similar to the geologic observation.

58 GEOSCIENCES↗

An explosion aftershock model with application to on-site inspection

An estimate of aftershock activity due to a theoretical underground nuclear explosion is produced using an aftershock rate model. The model is developed with data from the Nevada National Security Site, formerly known as the Nevada Test Site, and the Semipalatinsk Test Site, which we take to represent soft-rock and hard-rock testing environments, respectively. Estimates of expected magnitude and number of aftershocks are calculated using the models for different testing and inspection scenarios. These estimates can help inform the Seismic Aftershock Monitoring System (SAMS) deployment in a potential Comprehensive Test Ban Treaty On-Site Inspection (OSI), by giving the OSI team a probabilistic assessment of potential aftershocks in the Inspection Area (IA). The aftershock assessment, combined with an estimate of the background seismicity in the IA and an empirically derived map of threshold magnitude for the SAMS network, could aid the OSI team in reporting. Here, we apply the hard-rock model to a M5 event and combine it with the very sensitive detection threshold for OSI sensors to show that tens of events per day are expected up to a month after an explosion measured several kilometers away.

58 GEOSCIENCES↗

RePED 250: A Revolutionary, High Drilling Rate, High-T Geothermal Drilling System and Companion Power Electronics

Geothermal drilling in the United States is drastically slower and more costly than Oil and Gas (O&G) drilling, primarily due to the additional challenges in geothermal wells: hard rock types and high temperatures. The Repetitive Pulsed Electric Drill (250°C) (RePED-250), developed by Tetra Corporation has the potential to change this with a novel electro-crushing technology. RePED-250 releases pulses of electricity through the rock, which causes it to break in tension, instead of compression like conventional rotary drilling. The tensile strength of hard rocks like granite is only ~5% of their compressive strength, requiring less energy, time, and wear on the bit compared to conventional drilling. The RePED drill bit has no moving parts, uses drilling mud to remove rock fragments, and uses standard drill pipe, enabling a direct transition from conventional drilling systems. The objective of this project is to move RePED technology towards commercial readiness for high-temperature geothermal applications. This involves: 1) Creating high-temperature, high power electronic components for the RePED drill capable of operating at the high temperatures of a geothermal well. The target is a 250°C ambient environment. Specifically, capacitors, high voltage switches, and a downhole generator capable of generating the necessary power. 2) Demonstrating RePED’s effectiveness drilling through hard rock (granite) and examining its pathway to commercialization and effect on the US geothermal market. Work on this project has led to significant improvement over the state-of-the-art for all the examined electronics, through design, modeling, and testing of these novel components, though some additional development is still needed to deploy these high-temperature parts in a geothermal well. Besides their use in RePED-250, each component has applications in other industries where the stability of electronics at high-temperature is needed. To address the second barrier to commercialization, a 9” hole was drilled through a sample block of granite, demonstrating the tool’s effectiveness in hard rock. The team investigated RePED-250’s effect on well cost and the geothermal industry, through various techno-economic models described in the report.

15 GEOTHERMAL ENERGY↗

RePED 250: A Revolutionary, High Drilling Rate, High-T Geothermal Drilling System and Companion Power Electronics (Final Report)

Geothermal drilling in the United States is drastically slower and more costly than Oil and Gas drilling, primarily due to the additional challenges in geothermal wells: hard rock types and high temperatures. The Repetitive Pulsed Electric Drill (250 degrees C) (RePED-250), developed by Tetra Corporation has the potential to change this with a novel electro-crushing technology. RePED-250 releases pulses of electricity through the rock, which causes it to break in tension, instead of compression like conventional rotary drilling. The tensile strength of hard rocks like granite is only ~5% of their compressive strength, requiring less energy, time, and wear on the bit than conventional drilling. The RePED drill bit has no moving parts, uses drilling mud to remove rock fragments, and standard drill pipe, enabling a direct transition from conventional drilling systems. The objective of this project is to move RePED technology towards commercial readiness for high-temperature geothermal applications. This involves: 1) Creating high-temperature, high power electronic components for the RePED drill capable of operating at the high temperatures of a geothermal well. The target is a 250 degrees C ambient environment. Specifically, capacitors, high voltage switches, and a downhole generator capable of generating the necessary power. 2) Demonstrating RePED's effectiveness drilling through hard rock (granite) and examining its pathway to commercialization and effect on the US geothermal market. Work on this project has led to significant improvement over the state-of-the-art for all the examined electronics, through design, modeling, and testing of these novel components, though some additional development is still needed to deploy these high-temperature parts in a geothermal well. Besides their use in RePED-250, each component has applications in other industries where the stability of electronics at high-temperature is needed. To address the second barrier to commercialization, a 9" hole was drilled through a sample block of granite, demonstrating the tool's effectiveness in hard rock. The team investigated RePED-250's effect on well cost, and the geothermal industry, through various models described in the report.

15 GEOTHERMAL ENERGY↗

Laser-Mechanical Drilling for Geothermal Energy: Low-Contact Drilling Technology to Enable Economical EGS Wells

Broad Funding Opportunity Announcement Project: Foro Energy is developing a unique capability and hardware system to transmit high power lasers over long distances via fiber optic cables. This laser power is integrated with a mechanical drilling bit to enable rapid and sustained penetration of hard rock formations too costly to drill with mechanical drilling bits alone. The laser energy that is directed at the rock basically softens the rock, allowing the mechanical bit to more easily remove it. Foro Energy’s laser-assisted drill bits have the potential to be up to 10 times more economical than conventional hard-rock drilling technologies, making them an effective way to access the U.S. energy resources currently locked under hard rock formations.

ARPA-E↗

Development of a high-temperature diagnostics-while-drilling tool.

The envisioned benefits of Diagnostics-While-Drilling (DWD) are based on the principle that high-speed, real-time information from the downhole environment will promote better control of the drilling process. Although in practice a DWD system could provide information related to any aspect of exploration and production of subsurface resources, the current DWD system provides data on drilling dynamics. This particular set of new tools provided by DWD will allow quicker detection of problems, reduce drilling flat-time and facilitate more efficient drilling (drilling optimization) with the overarching result of decreased drilling costs. In addition to providing the driller with an improved, real-time picture of the drilling conditions downhole, data generated from DWD systems provides researchers with valuable, high fidelity data sets necessary for developing and validating enhanced understanding of the drilling process. Toward this end, the availability of DWD creates a synergy with other Sandia Geothermal programs, such as the hard-rock bit program, where the introduction of alternative rock-reduction technologies are contingent on the reduction or elimination of damaging dynamic effects. More detailed descriptions of the rationale for the program and early development efforts are described in more detail by others [SAND2003-2069 and SAND2000-0239]. A first-generation low-temperature (LT) DWD system was fielded in a series of proof-of-concept tests (POC) to validate functionality. Using the LT system, DWD was subsequently used to support a single-laboratory/multiple-partner CRADA (Cooperative Research and Development Agreement) entitled Advanced Drag Bits for Hard-Rock Drilling. The drag-bit CRADA was established between Sandia and four bit companies, and involved testing of a PDC bit from each company [Wise, et al., 2003, 2004] in the same lithologic interval at the Gas Technology Institute (GTI) test facility near Catoosa, OK. In addition, the LT DWD system has been fielded in cost-sharing efforts with an industrial partner to support the development of new generation hard-rock drag bits. Following the demonstrated success of the POC DWD system, efforts were initiated in FY05 to design, fabricate and test a high-temperature (HT) capable version of the DWD system. The design temperature for the HT DWD system was 225 C. Programmatic requirements dictated that a HT DWD tool be developed during FY05 and that a working system be demonstrated before the end of FY05. During initial design discussions regarding a high-temperature system it was decided that, to the extent possible, the HT DWD system would maintain functionality similar to the low temperature system, that is, the HT DWD system would also be designed to provide the driller with real-time information on bit and bottom-hole-assembly (BHA) dynamics while drilling. Additionally, because of time and fiscal constraints associated with the HT system development, the design of the HT DWD tool would follow that of the LT tool. The downhole electronics package would be contained in a concentrically located pressure barrel and the use of externally applied strain gages with thru-tool connectors would also be used in the new design. Also, in order to maximize the potential wells available for the HT DWD system and to allow better comparison with the low-temperature design, the diameter of the tool was maintained at 7-inches. This report discusses the efforts associated with the development of a DWD system capable of sustained operation at 225 C. This report documents work performed in the second phase of the Diagnostics-While-Drilling (DWD) project in which a high-temperature (HT) version of the phase 1 low-temperature (LT) proof-of-concept (POC) DWD tool was built and tested. Descriptions of the design, fabrication and field testing of the HT tool are provided. Background on prior phases of the project can be found in SAND2003-2069 and SAND2000-0239.

42 ENGINEERING↗

Testing the MDAC2 Far-field Approximation with Application to SPE-5 and DAG-2

Our test is to compare calculated far-field amplitudes with the MDAC2 predicted amplitudes for two source media; one where the source is in hard-rock (SPE-5) and one where the source is in soft-rock (DAG-2). The receiver medium will remain the same, and is similar to the hard-rock source medium. The far-field displacement amplitudes are calculated by the Serpentine Wave Propagation 4th-order (SW4) solver. More information on SW4 can be found in Petersson and Sjogreen (2017).

58 GEOSCIENCES↗