Search NASA⌕ Search

SEARCH · Search NASA

Results for “high areal capacity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Designing interphases for practical aqueous zinc flow batteries with high power density and high areal capacity

Aqueous zinc flow batteries (AZFBs) with high power density and high areal capacity are attractive, both in terms of cost and safety. A number of fundamental challenges associated with out-of-plane growth and undesirable side reactions on the anode side, as well as sluggish reaction kinetics and active material loss on the cathode side, limit practical deployment of these batteries. We investigated artificial interphases created using a simple electrospray methodology as a strategy for addressing each of these challenges. The effectiveness of the electrospray interphases in full cell zinc-iodine flow batteries was evaluated and reported; it is possible to simultaneously achieve high power density [115 milliwatts per square centimeter (mW/cm 2 )] and high areal capacity [25 milliampere hour per square centimeter (mA·hour/cm 2 )]. Last, we extended it to aqueous zinc-bromine and zinc-vanadium flow batteries of contemporary interest. It is again found that high power density (255 and 260 mW/cm 2 , respectively) and high areal capacity (20 mA·hour/cm 2 ) can be simultaneously achieved in AZFBs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Enabling high areal capacity for Co-free high voltage spinel materials in next-generation Li-ion batteries

The rapidly growing technological demand for lithium-ion batteries has prompted the development of novel cathode materials with high energy density, low cost, and improved safety. High voltage spinel, LiNi 0.5 Mn 1.5 O 4 (LNMO), is one of the most promising candidates yet to be commercialized. The two primary obstacles for this material are the inferior electronic conductivity and fast capacity degradation in full cells due to the high operating voltage. By systematically addressing these limitations, we successfully develop a thick LNMO electrode with areal capacity loadings up to 3 mAh·cm –2 . The optimized thick electrode is paired with a commercial graphite anode at both the coin cell and pouch cell level, achieving a full cell capacity retention as high as 72% and 78%, respectively, after 300 cycles. We attribute this superior cycling stability to careful optimizations of cell components and testing conditions, with a specific focus improving electronic conductivity and high voltage compatibility. These results suggest precise control of materials quality, electrode architecture and electrolyte optimization can soon support the development of a cobalt-free battery system based on a thick LNMO cathode (>4 mAh·cm 2 ), which will eventually meet the needs of next-generation Li-ion batteries with reduced cost, improved safety, and assured sustainability.

25 ENERGY STORAGE↗
DOE OSTI2023

Lithium-compatible and air-stable vacancy-rich Li 9 N 2 Cl 3 for high–areal capacity, long-cycling all–solid-state lithium metal batteries

Attaining substantial areal capacity (>3 mAh/cm 2 ) and extended cycle longevity in all–solid-state lithium metal batteries necessitates the implementation of solid-state electrolytes (SSEs) capable of withstanding elevated critical current densities and capacities. In this study, we report a high-performing vacancy-rich Li 9 N 2 Cl 3 SSE demonstrating excellent lithium compatibility and atmospheric stability and enabling high–areal capacity, long-lasting all–solid-state lithium metal batteries. The Li 9 N 2 Cl 3 facilitates efficient lithium-ion transport due to its disordered lattice structure and presence of vacancies. Notably, it resists dendrite formation at 10 mA/cm 2 and 10 mAh/cm 2 due to its intrinsic lithium metal stability. Furthermore, it exhibits robust dry-air stability. Incorporating this SSE in Ni-rich LiNi 0.83 Co 0.11 Mn 0.06 O 2 cathode-based all–solid-state batteries, we achieve substantial cycling stability (90.35% capacity retention over 1500 cycles at 0.5 C) and high areal capacity (4.8 mAh/cm 2 in pouch cells). These findings pave the way for lithium metal batteries to meet electric vehicle performance demands.

25 ENERGY STORAGE↗
DOE OSTI2022

A Bilayer Electrolyte Design to Enable High-Areal-Capacity Composite Cathodes in Polymer Electrolytes Based Solid-State Lithium Metal Batteries

High-areal-capacity cathodes are needed for energy-dense solid-state batteries. Here, we demonstrate a bilayer polymer electrolyte design for cycling 3–6 mAh/cm 2 NMC811 composite cathodes. In this work, the bilayer electrolyte comprises a cross-linked poly(ethylene oxide) (PEO)-based electrolyte layer and a linear-PEO-based electrolyte layer. The former provides dendritic resistance, and the latter provides a seamless interface with the cathode during cycling. Using a single layer of either membrane led to severe shorting or extremely low Coulombic efficiency (CE) in the first cycle. The general concept of a rigid dendrites-inhibiting electrolyte facing Li anode and a softer, cathode-integrated electrolyte that ensures contact with the cathodes during cycling may present a pattern for enabling high-energy-density cathodes.

25 ENERGY STORAGE↗
DOE OSTI2020

Reversible (De)Intercalation of Hydrated Zn 2+ in Mg 2+ -Stabilized V 2 O 5 Nanobelts with High Areal Capacity

The rechargeable aqueous zinc ion battery (ZIB) is regarded as one of the most promising candidates for large-scale energy storage applications due to its low-cost and eco-friendly properties. However, the development of a suitable cathode operating with high areal capacity and uncovering the relevant reaction mechanisms remain challenging. Herein, the application of Mg 0.26 V 2 O 5 ∙0.73H 2 O (MVO) nanobelts as a ZIB cathode is demonstrated. In situ FT-IR reveals the shift of OH stretching from 3350 cm -1 to 3200 cm -1 , corresponding to the hydration shell of Zn 2+ , while in situ Raman suggests the interlayer charges creening effect, which would boost the intercalation of hydrated Zn 2+ . Density function theory reveals that the hydrated Zn 2+ can lower the Coulombic repulsion at the electrode-electrolyte interface and circumvents the desolvation penalty of hydrated Zn 2+ during the (de)intercalation process. Additionally, excellent structure stability and large interlayer spacing guarantee the highly reversible (de)intercalation of hydrated Zn 2+ . Therefore, the MVO nanobelts exhibit a high areal capacity of 2.12 mAh cm -2 at 0.05 A g -1 , outstanding cycling stability of 2500 cycles at 10 A g -1 with a mass loading of 5 mg cm -2 . Finally, it is believed that the use of hydrated intercalation charge carriers will boost further studies in other multivalent rechargeable batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

Tortuosity Engineering for Improved Charge Storage Kinetics in High-Areal-Capacity Battery Electrodes

The increasing demands of electronic devices and electric transportation necessitate lithium-ion batteries with simultaneous high energy and power capabilities. However, rate capabilities are often limited in high-loading electrodes due to the lengthy and tortuous ion transport paths with their electrochemical behaviors governed by complicated electrode architectures still elusive. Here, we report the electrode-level tortuosity engineering design enabling improved charge storage kinetics in high-energy electrodes. Both high areal capacity and high-rate capability can be achieved beyond the practical level of mass loadings in electrodes with vertically oriented architectures. The electrochemical properties in electrodes with various architectures were quantitatively investigated through correlating the characteristic time with tortuosity. The lithium-ion transport kinetics regulated by electrode architectures was further studied via combining the three-dimensional electrode architecture visualization and simulation. Finally, the tortuosity-controlled charge storage kinetics revealed in this study can be extended to general electrode systems and provide useful design consideration for next-generation high-energy/power batteries.

25 ENERGY STORAGE↗
DOE OSTI2023

3D–Integrated, Multi–Functional Carbon Fibers for Stable, High–Areal–Capacity Batteries

Increasing lithium-ion batteries' (LIBs) electrode areal capacity can boost energy density and lower manufacturing costs, but faces challenges in manufacturing, rate performance, and cycling stability. A conductive framework made of commercial micro-sized carbon fibers (Cfs) is presented that serves as a host for both the LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC 532) cathode and Cfs anode. The Cf framework has multiple functions that offer high electronic conductivity (270 mS cm –1 ), low tortuosity (1.7), low Li + diffusion resistance (22 Ω), and high thermal conductivity (200 W mK –1 ). Additionally, the Cf-integrated electrodes can have an extremely high mass loading of NMC 532 (70 mg cm –2 ) with a theoretical capacity of 14 mAh cm –2 . Thus, the practical full cells assembled with the Cfs-enabled electrodes exhibit an initial areal capacity of 4.1 mAh cm –2 and capacity retention of 90.4% at 500 cycles at a cycling rate of C/3, 1.5 mA cm –2 . Data collected from the operando isothermal microcalorimetry suggest that full cells utilizing the Cf anode experience less heat release from side reactions compared to cells utilizing a conventional graphite anode. Finally, this present approach is scalable and cost-effective and can fabricate practical LIBs that boast high areal capacity, rate performance, and a lengthy cycling lifetime.

25 ENERGY STORAGE↗
DOE OSTI2021

The Role of Metal Oxides in Li-S Batteries: A High-Areal-Capacity Sulfur Composite Cathode Investigation

Compared to lithium-ion batteries (LIB), lithium-sulfur (Li-S) batteries have low cost and high theoretical specific energy (2510 Wh/kg or about 10 times of the LIB). However, Li-S batteries have several challenges, including large volume expansion, poor utilization of the end products, sluggish kinetics of polysulfides, and crossover, so-called the "shuttle effect". To address these issues, we have introduced metal oxides to the Li-S electrode to develop a metal-oxide-sulfur composite electrode. We aim to use metal oxides to assist the Li-S formation (dissociation) during discharge (charge) cycles. We elect to focus on LIB-based metal oxides to ensure that the added material can contribute storage capacity to the battery. Our cathodes are fabricated by both the conventional slurry casting and air-controlled electrospray. LIB electrode materials, such as Li(Ni 0.6 Mn 0.6 Co 0.2 )O 2 , LiMn 2 O 4 , Li 2 TiO 3 , etc, were incorporated with the sulfur-carbon composite and their charge-discharge performances are compared. We found that the presence of metal oxides increased sulfur utilization with stable cycling performance, even in cells with high areal capacities. To unveil the interactions between lithium metal oxides and sulfur, the cathodes were analyzed by various characterization techniques, including scanning electron microscopy, X-ray diffraction, thermogravimetric analysis, and electrochemistry. The analysis of the role of the oxides will be presented along with the reaction mechanism.

25 ENERGY STORAGE↗
DOE OSTI2024

Lithium Plating Characteristics in High Areal Capacity Li-Ion Battery Electrodes

Li-ion battery degradation and safety events are often attributed to undesirable metallic lithium plating. Since their release, Li-ion battery electrodes have been made progressively thicker to provide a higher energy density. However, the propensity for plating in these thicker pairings is not well understood. Herein, we combine an experimental plating-prone condition with robust mesoscale modeling to examine electrode pairings with capacities ranging from 2.5 to 6 mAh/cm 2 and negative to positive (N/P) electrode areal capacity ratio from 0.9 to 1.8 without the need for extensive aging tests. Using both experimentation and a mesoscale model, we identify a shift from conventional high state-of-charge (SOC) type plating to high overpotential (OP) type plating as electrode thickness increases. Further, these two plating modes have distinct morphologies, identified by optical microscopy and electrochemical signatures. We demonstrate that under operating conditions where these plating modes converge, a high propensity of plating exists, revealing the importance of predicting and avoiding this overlap for a given electrode pairing. Further, we identify that thicker electrodes, beyond a capacity of 3 mAh/cm 2 or thickness >75 μm, are prone to high OP, limiting negative electrode (NE) utilization and preventing cross-sectional oversizing the NE from mitigating plating. Here, it simply contributes to added mass and volume. The experimental thermal gradient and mesoscale model either combined or independently provide techniques capable of probing performance and safety implications of mild changes to electrode design features.

25 ENERGY STORAGE↗
DOE OSTI2022

High areal capacity, long cycle life 4 V ceramic all-solid-state Li-ion batteries enabled by chloride solid electrolytes

All-solid-state Li batteries (ASSBs) employing inorganic solid electrolytes offer improved safety and are exciting candidates for next-generation energy storage. Herein, we report a family of lithium mixed-metal chlorospinels, Li 2 In x Sc 0.666-x Cl 4 (0 ≤ x ≤ 0.666), with high ionic conductivity (up to 2.0 mS cm -1 ) owing to a highly disordered Li-ion distribution, and low electronic conductivity (4.7 × 10-10 S cm -1 ), which are implemented for high-performance ASSBs. Owing to the excellent interfacial stability of the SE against uncoated high-voltage cathode materials, ASSBs utilizing LiCoO 2 or LiNi 0.85 Co 0.1 Mn 0.05 O 2 exhibit superior rate capability and long-term cycling (up to 4.8 V versus Li+/Li) compared to state-of-the-art ASSBs. In particular, the ASSB with LiNi 0.85 Co 0.1 Mn 0.05 O 2 exhibits a long life of >3,000 cycles with 80% capacity retention at room temperature. Additionally, high cathode loadings are also demonstrated in ASSBs with stable capacity retention of >4 mAh cm -2 (~190 mAh g -1 ).

25 ENERGY STORAGE↗
DOE OSTI2023

A conformal heat-drying direct ink writing 3D printing for high-performance lithium-ion batteries

High areal capacity electrodes hold great potential for high-energy density lithium-ion batteries (LIBs), but their poor electrochemical kinetics limit their power density. Here, in this study, high areal capacity 3D-structured LiNi 0.8 Mn 0.1 Co 0.1 O 2 cathodes (4.3 mAh cm -2 ) are prepared via 3D printing with a manner of direct ink writing. The electrodes had an enlarged electrode–electrolyte contact area, shortened diffusion pathway, and reduced intercalation-induced stress, thereby delivering enhanced rate capability and cyclability in LIBs, which is 143.6 mAh g -1 at 3C and a 60.2 % capacity retention over 800 cycles at 1C. Moreover, at electrode level, the 3D-NMC exhibits an energy and power densities of 313.1 Wh kg -1 and 657.9 W kg -1 , respectively. Furthermore, the theoretical calculation suggests that reducing the gap width will be highly beneficial to the energy and power densities. This work establishes a milestone in understanding the cycling effect on the electrode local structure, including the void area and the LiNi 0.8 Mn 0.1 Co 0.1 O 2 region, which confirms the effectiveness of 3D printing for electrode preparation.

25 ENERGY STORAGE↗
DOE OSTI2023

Composite Lithium Metal Structure to Mitigate Pulverization and Enable Long‐Life Batteries

In lithium metal batteries, non‐uniform stripping of lithium results in pit formation, which promotes subsequent non‐uniform, dendritic deposition. This viscous cycle leads to pulverization of lithium which promotes cell shorting or capacity degradation, symptoms further exaggerated by high electrode areal loading and lean electrolytes. Here, to address this challenge, a composite lithium metal anode is engineered that contains uniformly distributed, nanometer‐sized carbon particles. This composite lithium is shown to strip more uniformly since the growth of non‐uniform pits is intercepted by the carbon particles. This mechanism is corroborated by a continuum electrochemical model. Subsequent lithium deposition on carbon particles is also found to be more uniform than on the surface with irregular pits. Notably, the pulverization rate of composite lithium is 26 times slower than that of commercial lithium. Moreover, in a Li‐S battery with sulfurized polyacrylonitrile cathode, the use of the composite anode extends the cycle life by three times when the areal capacity is 8 mAh cm −2 . The approach of using an engineered lithium composite structure to address challenges during both stripping and plating can inform future designs of lithium metal anodes for high areal capacity operations.

high areal capacity↗
DOE OSTI2022

Pushing Lithium–Sulfur Batteries towards Practical Working Conditions through a Cathode–Electrolyte Synergy

Abstract The commercialization of lithium–sulfur (Li−S) batteries is still hindered by the unsatisfactory cell performance under practical working conditions, which is mainly caused by the sluggish cathode redox kinetics, severe polysulfide shuttling, and poor Li stripping/plating reversibility. Herein, we report an effective strategy by combining Se‐doped S hosted in an ordered macroporous framework with a highly fluorinated ether (HFE)‐based electrolyte to simultaneously address the aforementioned issues in both cathode and anode. A reversible and stable high areal capacity of >5.4 mAh cm −2 with high Coulombic efficiency >99.2 % can be achieved under high areal Se/S loading (5.8 mg cm −2 ), while the underlying mechanism was further revealed through synchrotron X‐ray probes and Time‐of‐Flight Secondary Ion Mass Spectrometry (ToF‐SIMS). The practical application potential was further evaluated at low (0 °C) and high (55 °C) temperatures under high areal Se/S loading (>5.0 mg cm −2 ) and thin Li metal (40 μm).

Zhao, Chen↗