Search NASA⌕ Search

SEARCH · Search NASA

Results for “high current density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Growth and characterization of high current density, high-speed InAs/AlSb resonant tunneling diodes

InAs/AlSb double-barrier resonant tunneling diodes with peak current densities up to 370,000 A/sq cm and high peak-to-valley current ratios of 3.2 at room temperature have been fabricated. The peak current density is well-explained by a stationary-state transport model with the two-band envelope function approximation. The valley current density predicted by this model is less than the experimental value by a factor that is typical of the discrepancy found in other double-barrier structures. It is concluded that threading dislocations are largely inactive in the resonant tunneling process.

Soderstrom, J. R.↗
NASA NTRS1991

Comparison between the magnetic and transport critical current densities in high critical current density melt-textured yttrium barium copper-oxide

Using a recently developed pulsed critical current density (Jc) measuring system, the Jc of the high-Jc melt-textured YBa2Cu3O(7-delta) (Y123) bulk samples has been determined. I-V curves with a voltage resolution of 0.5 microV were obtained, and transport Jc's along the a-b plane as high as 7.2 x 10 to the 4th A/sq cm were extracted. These results are comparable to the values obtained magnetically. On the other hand, transport Jc along the c axis were found to be two orders of magnitude smaller, even though the magnetic Jc along the c axis is only about five times smaller than Jc along the a-b plane. It is suggested that for the high-temperature superconducting materials which are highly anisotropic, caution should be taken when using the nontransport magnetic methods to determine Jc.

Gao, L.↗
NASA NTRS2000

Very High Current Density Nb/AlN/Nb Tunnel Junctions for Low-Noise Submillimeter Mixers

We have fabricated and tested submillimeter-wave superconductor-insulator-superconductor (SIS) mixers using very high current density Nb/AlN/Nb tunnel junctions (J(sub c) approximately equal 30 kA/sq cm) . The junctions have low resistance-area products (R(sub N)A approximately 5.6 Omega.sq micron), good subgap to normal resistance ratios R(sub sg)/R(sub N) approximately equal 10, and good run-to-run reproducibility. From Fourier transform spectrometer measurements, we infer that omega.R(sub N)C = 1 at 270 GHz. This is a factor of 2.5 improvement over what is generally available with Nb/AlO(x)/Nb junctions suitable for low-noise mixers. The AlN-barrier junctions are indeed capable of low-noise operation: we measure an uncorrected receiver noise temperature of T(sub RX) = 110 K (DSB) at 533 GHz for an unoptimized device. In addition to providing wider bandwidth operation at lower frequencies, the AlN-barrier junctions will considerably improve the performance of THz SIS mixers by reducing RF loss in the tuning circuits.

Kawamura, Jonathan↗
NASA NTRS1967

Clamp provides efficient connection for high-density currents

Electrical connector clamp /bus bar/ gives high contact-surface efficiency for providing a high current to thin wall stainless steel tubing containing hydrogen gas. It uses lead solder film to provide the electrical equivalent of a fusion bond without degrading the grain structure, permitting disassembly and reuse of the components.

Mc Carthy, J. R.↗
NASA NTRS2002

Power-Efficient, High-Current-Density, Long-Life Thermionic Cathode Developed for Microwave Amplifier Applications

A power-efficient, miniature, easily manufactured, reservoir-type barium-dispenser thermionic cathode has been developed that offers the significant advantages of simultaneous high electron-emission current density (>2 A/sq cm) and very long life (>100,000 hr of continuous operation) when compared with the commonly used impregnated-type barium-dispenser cathodes. Important applications of this cathode are a wide variety of microwave and millimeter-wave vacuum electronic devices, where high output power and reliability (long life) are essential. We also expect it to enable the practical development of higher purveyance electron guns for lower voltage and more reliable device operation. The low cathode heater power and reduced size and mass are expected to be particularly beneficial in traveling-wave-tube amplifiers (TWTA's) for space communications, where future NASA mission requirements include smaller onboard spacecraft systems, higher data transmission rates (high frequency and output power) and greater electrical efficiency.

Wintucky, Edwin G.↗
NASA NTRS1977

Photoelectrolysis of water at high current density - Use of ultraviolet laser excitation

The behavior of TiO2 and SrTiO3 photoanodes in cells for the photoelectrolysis of H2O has been investigated for high-intensity 351-,364-nm excitation from an Ar ion laser. Intensities up to 380 W/sq cm have been used. For TiO2 a small amount of surface decomposition is found after irradiation at high intensity, whereas SrTiO3 undergoes no detectable changes. Current-voltage properties for both electrodes are essentially independent of light intensity up to the level of 380 W/sq cm, and there is little if any change in quantum efficiency for electron flow. Photocurrent densities have been shown to exceed 5 A/sq cm for O2 evolution. Data show that the energy storage rate associated with the SrTiO3 photoelectrolysis can exceed 30 W/sq cm; this represents the highest demonstrated rate of sustained optical-to-chemical energy conversion.

Bocarsly, A. B.↗
NASA NTRS1978

Photoelectrolysis of water at high current density - Use of laser light excitation of semiconductor-based photoelectrochemical cells

In the present paper, some results are given for UV laser light irradiation of the photoanode (SnO2, SrTiO3, or TiO2) in a cell for the light-driven electrolysis of H2O, at radiation intensities of up to 380 W/sq cm. The properties of the anode material are found to be independent of light intensity. Conversion of UV light to stored chemical energy in the form of 2H2/O2 from H2O was driven at a rate of up to 30 W/sq cm. High O2 evolution rates at the irradiated anodes without changes in the current-voltage curves are attributed to the excess oxidizing power associated with photogenerated holes. A test for this sort of hypothesis for H2 evolution at p-type materials is proposed.

Wrighton, M. S.↗
NASA NTRS1989

Orienting Superconductive Crystals For High Current Density

Proposed technique for controlled distortion of crystal grains in newly discoverd superconductor YBa2Cu3O7-x increases current-carrying capacity. Helps to ensure grains in this and other anisotropic materials all oriented in same direction so charge carriers transferred readily from one grain to another. Specimen of YBa2Cu3O7-x heated in oxygen atmosphere compressed in one direction as slowly cooled below transition temperature. Under these conditions, oxygen atoms tend to rearrange so as to relieve stress created by compression.

Shlichta, Paul J.↗
NASA NTRS2004

Field Emission Study of Carbon Nanotubes: High Current Density from Nanotube Bundle Arrays

We have investigated the field emission behavior of lithographically patterned bundles of multiwalled carbon nanotubes arranged in a variety of array geometries. Such arrays of nanotube bundles are found to perform significantly better in field emission than arrays of isolated nanotubes or dense, continuous mats of nanotubes, with the field emission performance depending on the bundle diameter and inter-bundle spacing. Arrays of 2-micrometers diameter nanotube bundles spaced 5 micrometers apart (edge-to-edge spacing) produced the largest emission densities, routinely giving 1.5 to 1.8 A/cm(sup 2) at approximately 4 V/micrometer electric field, and greater than 6 A/cm(sup 2) at 20 V/micrometers.

field emissions↗
NASA NTRS2019

A Multi-Physics Study on High-Specific Power Li-O2 Batteries for Electric Aircraft

Commercialization of lithium-air batteries faces many challenges, such as electrolyte decomposition, short cycle life, low energy and power density, etc. However, commercialization of Li-O2 batteries for aeronautics is much more challenging due to additional safety constraints on cyclability and performance (high specific power and specific energy). For this presentation, we will discuss inter-related aspects of physics-based modeling of a pack: cell and battery model calibration. In addition, we will evaluate and present optimal battery designs for high discharge current density, high discharge time, and low battery mass using simulation-based optimization.The Finite Element Model (FEM) used to simulate a Li-O2 cell is based on the work of Bevara [1]. The different aspects of the model are based on: porous electrode theory and concentrated electrolyte theory; quantum tunneling model for the resistance of conformal layer of discharge product (Li2O2) [1]; Butler-Volmer kinetics for electrochemical reaction; Fick's diffusion for oxygen transport; and an oxygen dissolution model is applied at the air/electrolyte interface [2]. The electrolyte properties such as ion conductivity, ion diffusion, oxygen diffusion, and mass density of the electrolyte were taken from Molecular Dynamics (MD) simulations [3]; while the other model parameters, which includes mass of cell components, were calibrated to match experiments at high discharge current densities. The cell mass includes the anode, cathode, separator, electrolyte, and other components (such as current collector). This calibrated model is used to perform parametric studies on cathode thickness, porosity, tortuosity, carbon particle size, electrolyte transport and material properties, partial pressure of oxygen, discharge time, and discharge current density to study optimal designs for high specific power and energy. References:1. Bevara, V. & Andrei, P. (2014), J. Electrochem. Soc. 161 (14), A2068-A2079.2.Mehta, M. & Andrei, P. (2015), J. Power Sources. 286, 299-308.3.Liyana-Arachchi, T.; Haskins, J.; Burke, C.; Diederichsen, K.; McCloskey, B.; & Lawson, J. (2018), J. Phys. Chem. B. 122 (36), 8548 - 8559.4.Choi, W.; Kikumoto, H.; Choudhary, R. & Ooka, R. (2018), Applied Energy, 209, 306-321.

Mehta, Mohit↗
NASA NTRSDate not supplied

Probing Sensitivity of Discharge Characteristics to Model Selection using Uncertainty Quantification in an aprotic Li-Oxygen Battery

Currently, there are several models in the literature, such as kinetic models, microstructural models, and mass transport models that describe a Li-air battery's discharge behavior. Many of these models are calibrated and tested at low current densities and cannot be easily transferred to high current densities. Even at low current densities, there is no quantitative method for a researcher to choose a reaction kinetic model such as classical Butler-Volmer and its derivatives, and modified Marcus-Hush-Chidsey, a resistance model for lithium peroxide such as electron transport via tunneling or linear resistivity, a surface coverage model (lithium peroxide growth) such as partial coverage or full coverage, and mass transport model (discussed in Ref. [1]). Also, it is time-consuming to test different models at high current density (1C) due to a lack of well-tested models and well-calibrated model parameters. For this presentation, we will develop an analytical model, which acts as a surrogate model for a sophisticated finite element model to predict discharge time and discharge voltage. Next, we use an uncertainty quantifying technique called reduced-order stochastic optimization [2, 3] to determine the uncertainty in model parameters for rate kinetics, lithium peroxide resistivity, and parasitic resistance. Finally, a finite element simulation is performed to determine the error introduced by the surrogate model and its influence on the uncertainty in the model parameters.

M Mehta↗
NASA NTRS1992

Fabrication and characterization of high current-density, submicron, NbN/MgO/NbN tunnel junctions

At near-millimeter wavelengths, heterodyne receivers based on SIS tunnel junctions are the most sensitive available. However, in order to scale these results to submillimeter wavelengths, certain device properties should be scaled. The tunnel-junction's current density should be increased to reduce the RC product. The device's area should be reduced to efficiently couple power from the antenna to the mixer. Finally, the superconductor used should have a large energy gap to minimize RF losses. Most SIS mixers use Nb or Pb-alloy tunnel junctions; the gap frequency for these materials is approximately 725 GHz. Above the gap frequency, these materials exhibit losses similar to those in a normal metal. The gap frequency in NbN films is as-large-as 1440 GHz. Therefore, we have developed a process to fabricate small area (down to 0.13 sq microns), high current density, NbN/MgO/NbN tunnel junctions.

Stern, J. A.↗
NASA NTRS1977

Competitively priced hydrogen via high-efficiency nuclear electrolysis

A fully dedicated nuclear-electrolytic hydrogen-production facility, based on advanced (1985) technology, has been synthesized and assessed at the conceptual level. The facility integrates an HTGR operating a binary shaftpower-extraction cycle at 980 C top temperature, direct dc electricity generation via acyclic generators, and high-current density high-pressure electrolyzers based on the solid polymer electrolyte approach. All subsystems are close-coupled and optimally interfaced. Pipeline-pressure hydrogen and coproduct oxygen are produced at 6900 kPa. On consistent costing bases, the advanced facility concept was found to provide hydrogen costs that were approximately half those associated with conventional, contemporary-technology nuclear electrolysis. The nuclear heat-to-hydrogen energy conversion efficiency for the advanced system was estimated as 43%, against 25% for the baseline present-day approach.

Escher, W. J. D.↗
NASA NTRS1977

Efficiency and cost advantages of an advanced-technology nuclear electrolytic hydrogen-energy production facility

The concept of an advanced-technology (viz., 1985 technology) nuclear-electrolytic water electrolysis facility was assessed for hydrogen production cost and efficiency expectations. The facility integrates (1) a high-temperature gas-cooled nuclear reactor (HTGR) operating a binary work cycle, (2) direct-current (d-c) electricity generation via acyclic generators, and (3) high-current-density, high-pressure electrolyzers using a solid polymer electrolyte (SPE). All subsystems are close-coupled and optimally interfaced for hydrogen production alone (i.e., without separate production of electrical power). Pipeline-pressure hydrogen and oxygen are produced at 6900 kPa (1000 psi). We found that this advanced facility would produce hydrogen at costs that were approximately half those associated with contemporary-technology nuclear electrolysis: $5.36 versus $10.86/million Btu, respectively. The nuclear-heat-to-hydrogen-energy conversion efficiency for the advanced system was estimated as 43%, versus 25% for the contemporary system.

Donakowski, T. D.↗
NASA NTRS1979

Dedicated nuclear facilities for electrolytic hydrogen production

An advanced technology, fully dedicated nuclear-electrolytic hydrogen production facility is presented. This plant will produce hydrogen and oxygen only and no electrical power will be generated for off-plant use. The conceptual design was based on hydrogen production to fill a pipeline at 1000 psi and a 3000 MW nuclear base, and the base-line facility nuclear-to-shaftpower and shaftpower-to-electricity subsystems, the water treatment subsystem, electricity-to-hydrogen subsystem, hydrogen compression, efficiency, and hydrogen production cost are discussed. The final conceptual design integrates a 3000 MWth high-temperature gas-cooled reactor operating at 980 C helium reactor-out temperature, direct dc electricity generation via acyclic generators, and high-current density, high-pressure electrolyzers based on the solid polymer electrolyte approach. All subsystems are close-coupled and optimally interfaced and pipeline hydrogen is produced at 1000 psi. Hydrogen costs were about half of the conventional nuclear electrolysis process.

Foh, S. E.↗
NASA NTRS1990

Effects of grain size and grain boundary on critical current density of high T(sub c) superconducting oxides

By means of adding impurity elements in high T sub c oxides, the effects were studied of grain size and grain boundary on the critical current density of the following systems: YBa2Cu3O(7-y) and Bi-Pr-Sr-Ca-Cu-O. In order to only change the microstructure instead of the superconductivity of the grains in the samples, the impurity elements were added into the systems in terms of the methods like this: (1) substituting Y with the lanthanide except Pr, Ce, and Tb in YBa2Cu3O(7-y) system to finning down grains in the samples, therefore, the effect can be investigated of the grain size on the critical current density of 1:2:3 compounds; (2) mixing the high T sub c oxides with the metal elements, such as Ag, according to the composition of (high T sub c oxide)1-xAgx to metallize the grain boundaries in the samples, studying the effect of the electric conductivity of the grain boundaries on the critical current density; (3) adding SiO2, PbO2, and SnO2 into the high T sub c oxide to form impurity phases in the grain boundaries, trying to find out the effects of the impurity phases or metalloid grain boundaries on the critical current density of the high T sub c superconductors. The experimental results indicate that in the case of of the presence of the metalloid grain boundaries finning down grains fails to enhance the j sub c, but restrains it strongly, the granular high T sub c superconductors with the small size grains coupled weakly is always the low j sub c system.

Zhao, Y.↗
NASA NTRS1989

Characteristic parameters of superconductor-coolant interaction including high Tc current density limits

In the area of basic mechanisms of helium heat transfer and related influence on super-conducting magnet stability, thermal boundary conditions are important constraints. Characteristic lengths are considered along with other parameters of the superconducting composite-coolant system. Based on helium temperature range developments, limiting critical current densities are assessed at low fields for high transition temperature superconductors.

Frederking, T. H. K.↗