Search NASA⌕ Search

SEARCH · Search NASA

Results for “high efficiency architectures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records

III-V PV Cell Core Capability (Final Technical Report)

This Core project developed III-V photovoltaics for terrestrial applications, focusing on high efficiency architectures and on cost-reduction. III-V cells have demonstrated the highest efficiencies of any photovoltaic materials system, reaching over 30% for two- junction tandems and over 47% for more complex concentrator cells. III-Vs have other characteristics that make them attractive to a range of terrestrial and near-terrestrial energy applications, such as being direct absorbers, lightweight and potentially flexible, having good thermal coefficient, good radiation hardness, and being very stable and durable. Cost is a key challenge with III-Vs, however, because of the high cost of epitaxy and processing.

14 SOLAR ENERGY↗

Development and Test Progress Towards a Supercritical Carbon Dioxide-Based Gas Turbine Waste Heat Recovery System

Supercritical carbon dioxide systems are the focus of significant recent research efforts and promise compact, high-efficiency architecture for gas turbine waste heat recovery for pipeline gas turbines. The waste heat recovery system improves operating efficiency by converting waste heat to additional electric power, which increases overall system efficiency by 35% at the design point, and also significantly improves part-load performance. This paper describes the system design and component selection for a 5.7 MWe waste heat recovery system based on an integrally-geared compressor-expander architecture, including the thermodynamic cycle development, system architecture and component trade studies, and final selection. Validation test results for critical first-of-a-kind compressor and turbine component technologies are also presented, demonstrating full-pressure performance and progress towards commercialization.

wilkes, Jason↗

UV-Induced Degradation of High-Efficiency Solar Cells with Different Architectures

The ultraviolet-induced degradation (UVID) of solar panels is associated with the deterioration of cell performance and reduced reliability of packaging materials. Here we examine the UV stability of different architectures of high-efficiency solar cells without any encapsulation. Identical UV exposure tests were performed at two different labs using UVA-340 fluorescent lamps under different electrical bias configurations (open- or short-circuit) and irradiated cell surfaces (for bifacial technologies). Cell technologies, including heterojunction (HJ), interdigitated back-contact cells (IBC), passivated emitter rear contact (PERC), passivated emitter rear totally-diffused (PERT), are found to be more susceptible to UVID, leading to significant Isc loss (up to 4%) and P max loss (up to 15%) as compared to the conventional back surface field (Al-BSF) cells after exposure to UV irradiation of 8.92 MJ-m -2 -nm -1 at 340 nm. Additionally, the bifacial cells when irradiated from the backside exhibited greater photocurrent loss compared to the front side exposure, indicating potential sensitivity of rear surface passivation to UV radiation.

crystalline silicon↗

SSL Luminaire with Novel Driver Architecture

Cree has developed a new high-efficiency light emitting diode (LED) technology platform capable of providing low-cost, high performance luminaires that can be adopted across a variety of SSL applications. This development is built on Cree’s high brightness LED platform to design a novel LED chip that enables a high-efficiency driver architecture to improve the overall luminaire system efficacy. These system efficiency gains were realized using an integrated approach tailoring the LED chip characteristics to allow for the high-efficiency driver technology platform. The reliability of the new LED design was robust at the component level under accelerated testing conditions. Luminaires were assembled integrating the novel LED and driver technology to demonstrate the system improvement. Cree has successfully completed this project by developing a novel LED architecture that enables a new driver design with 93% efficiency. This technology was showcased in an LED luminaire that produced 725 lumens at an efficacy of 87.4 lumens per watt (LPW). The correlated color temperature (CCT) of the luminaire was 2708 K with a color rendering index (CRI) of 91. The novel LEDs and driver led to a 9% system performance improvement compared to the standard LEDs and driver scheme.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

High efficiency and low roll-off blue phosphorescent organic light-emitting devices using mixed host architecture

We report high efficiency and low roll-off for blue electrophosphorescent organic light emitting devices (OLEDs) based on a mixed host layer architecture. The devices were fabricated using a mixed layer of di-[4-(N,N-ditolyl-amino)-phenyl]cyclohexane (TAPC), a hole transport material, and 2,8-bis(diphenylphosphoryl)dibenzothiophene (PO15), an electron transport material, as the host layer doped with the blue phosphor iridium (III) bis[(4,6-difluorophenyl)-pyridinato-N,C2’]picolinate (FIrpic). Using a mixed layer as the host allowed us to achieve high power efficiency (59 lm/W at 100 cd/m2), low turn-on voltage (2.7 V for >10 cd/m2), and low roll-off in these devices.

42 ENGINEERING↗

Al x In 1-x P LEDs with II-VI Cladding Layers for Efficient Red and Amber Emission. Final Scientific & Technical Report

Realizing solid state lighting systems with high efficiency and enhanced functionality will require the adoption of color-mixing (cm-LEDs) architectures combining highly efficient red, green, blue and amber light emitting diodes. Already, the hybrid architectures (hy-LEDs) pair phosphor-converted wide bandgap nitride LEDs with (Al x Ga 1-x ) 0.51 In 0.49 P red LEDs to improve the emission spectrum and reduce losses in the infrared. However, the efficiencies of (Al x Ga 1-x ) 0.51 In 0.49 P red and amber LEDs are still too low to truly enable these approaches. The DOE Solid-State Lighting R&D Plan highlights red and amber LED improvement as a long-term research goal. Excessive electron leakage out of the cladding layers, in particular, leads to strong thermal droop and red LED efficiencies of ~25% at normal operating temperatures. The typical device architecture for red and amber LEDs is based on indirect bandgap (Al y Ga 1-y ) 0.51 In 0.49 P cladding layers used to confine injected electrons and holes within a lower, direct bandgap (Al x Ga 1-x ) 0.51 In 0.49 P light-emitting active layer (x < y). The challenge with this approach is that the electron confinement is limited and decreases as the emission wavelength is shortened. Hence, thermal droop and overall device efficiency are very poor for amber LEDs. Innovative solutions to this problem must be sought through the use of new semiconductor materials and structures that will increase electron confinement. We plan to develop Al x In 1-x P LEDs with a II-VI semiconductor electron cladding layer to greatly increase the carrier confinement. Such an approach has the potential to improve red and amber LED efficiency, temperature stability, and light extraction. Al x In 1-x P active layers provide high direct bandgap energies needed to reach amber wavelengths without detrimental internal losses. ZnSe-based alloys are attractive candidates for the electron cladding layer because they can be engineered to provide high conduction band energies relative to the Al x In 1-x P active layer while maintaining roughly the same lattice constant. The lower index of refraction of the II-VI cladding layer will also aid light extraction. While extended defects have largely precluded the use of II-VI semiconductors as the light emitting layer in LEDs and lasers, the effects of these defects on device performance can be mitigated by limiting the use of II-VI materials to the thin, heavily doped cladding layer. Proposed research will focus on optimizing the quality of the Al x In 1-x P active layer and the heteropolar growth of the III-V/II-VI interface, tuning the II-VI cladding layer composition, and device design to maximize electron confinement and LED efficiency. Significant improvement in the performance of red and amber LEDs through this new approach is expected to advance the capabilities of next generation solid-state lighting technologies.

36 MATERIALS SCIENCE↗

High Temperature Additive Architectures for 65% Efficiency (Final Report)

GE Power (GEP) proposed a development program that targets advanced high temperature additive components that contribute towards the DOE’s goal for advanced gas turbines that are capable of 65%, or greater, efficiency in combined cycle application. GEP proposed to leverage state-of-the-art additive manufacturing to develop novel and innovative component airfoil and end wall architectures that provide cooling flow savings while maintaining the component durability expected in today’s gas turbines. The objective of this program was to develop advanced component designs and architectures enabled by additive manufacturing, and the materials systems and additive manufacturing technology required for these designs. This Phase I program leveraged existing design and analysis knowledge and techniques for additive materials and methods and utilized extensive analytical evaluations to develop and refine designs for advanced turbine hot gas path (HGP) components. The design will be the basis for development and testing in a potential Phase II program. The goal of this Phase I program was to establish a feasible conceptual design for advanced additive turbine hot section components along with a technology maturation plan involving testing to address risk areas and needed validation. It was approached through two primary elements: 1) conceptual design and analysis of wall architectures, advanced airfoil cooling concepts, and advanced system-level concepts, and 2) investigation of additive modalities and associated materials systems. The Phase I program has concluded with the down-select of a primary design concept for a potential Phase II program.

36 MATERIALS SCIENCE↗

High Temperature Additive Architectures for 65% Efficiency (Final Technical Report)

This project aimed to develop advanced high-temperature additive components that contribute towards the DOE’s goal for advanced gas turbines that are capable of at least 65% efficiency in combined cycle application. The objective was to leverage state-of-the-art additive manufacturing to develop an innovative stage 1 turbine nozzle (S1N) that can provide cooling flow savings while maintaining the component durability expected in today’s gas turbines. The program had two phases. Phase I was a conceptual phase for novel advanced cooling designs enabled by additive manufacturing, as well as proposals for validation. Phase II included execution of the Phase I conceptual design, including manufacturing of prototype hardware and validation within an environment that is similar to engine operation. During Phase I of the program, the team devised a concept to reduce cooling air usage. The cooling air used in the side walls is filmed out along the side walls, while the cooling air used in the airfoil is eventually directed to near-wall channels and exits holes along the airfoil trailing end. During this program, the team performed additive trials to analyze the geometric limitations of additive manufacturing. This helped the team understand minimum wall thicknesses, hole sizes, and cooling channel dimensions among other limits. Phase II of this program pushed GE Vernova beyond its previous experience of designing and manufacturing an additively manufactured hot gas path component. Modern hot gas path components utilize material chemistries that are traditionally hard to weld, such as cast Renè 108, and exhibit solidification cracking when additively manufactured using Direct Metal Laser Melting (DMLM). Note that AM108 is a powder form of Renè 108. A S1N with advanced cooling is larger and more complex than parts previously built by additive manufacturing and required new learnings to resolve risks around solidification cracking. Finally, the team validated the design in a combustion rig that replicated operation in a gas turbine. In order to properly quantify the benefits of the new additive design, a baseline was also tested in the rig and operated under the same conditions. In addition, an uncertainty analysis was done to quantify any sources of error that could impact the results. At the end of the validation effort, it was determined that the additive nozzle exceeded the 15% reduction in cooling flow goal even with the worst-case assumptions for uncertainty.

03 NATURAL GAS↗

Device Architecture and Lifetime Requirements for High Efficiency Multicrystalline Silicon Solar Cells

We present a numerical simulation study of different multicrystalline silicon materials and solar cell architectures to understand today's efficiency limitations and future efficiency possibilities. We compare conventional full-area BSF and PERC solar cells to future cell designs with a gallium phosphide heteroemitter. For all designs, mc-Si materials with different excess carrier lifetime distributions are used as simulation input parameters to capture a broad range of materials. The results show that conventional solar cell designs are sufficient for generalized mean lifetimes between 40 – 90 μs, but do not give a clear advantage in terms of efficiency for higher mean lifetime mc-Si material because they are often limited by recombination in the phosphorus diffused emitter region. Heteroemitter designs instead increase in cell efficiency considerable up to generalized mean lifetimes of 380 μs because they are significantly less limited by recombination in the emitter and the bulk lifetime becomes more important. In conclusion, to benefit from increasing mc-Si lifetime, new cell designs, especially heteroemitter, are desirable.

14 SOLAR ENERGY↗

Efficient, Compact, and Smooth Variable Propulsion Motor (Final Report)

In this project, a new architecture of highly efficient hydraulic motor was developed for the propulsion of off-highway vehicles. The motor uses an adjustable linkage driving a cam to vary the displacement of the piston, resulting in a Variable Displacement Linkage Motor (VDLM). The motor uses low friction rolling element bearings to significantly reduce mechanical friction, especially in the demanding low-speed high-torque conditions experienced by off-highway vehicles. The VDLM has high torque capabilities for its size due to the radial piston packaging and use of a multi-lobe cam. A VDLM is very smooth due to the ability to tune the torque ripple through the design of the cam profile. The project was divided into three periods. During the first period, a dynamic model was constructed of the motor to predict the performance of the motor and the vehicle. During the second period, a single-cylinder learning prototype was designed, built, and tested to validate the models constructed in the first period. In the third period, a multi-cylinder prototype motor was optimized, designed, fabricated, and tested. The motor demonstrated excellent mechanical efficiency (above 92.5% across the range of displacements), but the experimentally measure volumetric efficiency was lower than expected due to higher leakage rates created by the poor tolerance control on the prototype. To validate the dynamic models developed in the first period and better understand design trade-offs. In the third period a multi-cylinder concept demonstration prototype will be designed, fabricated, and tested. The final prototype will be tested on a motor dynamometer and will be utilized in hardware-in-the-loop testing to demonstrate its efficiency and performance impacts on the overall drive train. The experimental results were used in a drive train simulation of a compact track loader operating through a drive cycle. Using the VDLM in a hydrostatic circuit yielded 17.1% reduction in fuel consumption and 36.5% reduction in a series hybrid transmission.

99 GENERAL AND MISCELLANEOUS↗

Lossless Phonon Transition Through GaN‐Diamond and Si‐Diamond Interfaces

Abstract Advancing Silicon (Si) technology beyond Moore's law through 3D architectures requires highly efficient heat management methods compatible with foundry processes. While continued increases in transistor density can be achieved through 3D architectures, self‐heating in the upper tiers degrades the performance. Self‐heating is a critical problem for high‐power, high‐frequency, wide bandgap, and ultra‐wide bandgap devices as well. Diamond, known for its exceptional thermal conductivity, offers a viable solution in both these cases. Since thermal boundary resistance (between the channel/junction and diamond plays a crucial role in overall thermal resistance, this study investigates various dielectrics for interface engineering, such as Silicon dioxide (SiO 2 ), amorphous‐ Silicon Carbide (a‐SiC), and Silicon Nitride (SiN x ), to make a phonon bridge at gallium nitride (GaN)‐diamond and Si‐diamond interfaces. The a‐SiC interlayer reduces diamond/GaN (<5 m 2 K per GW) and diamond/Si (<2 m 2 K per GW) thermal boundary resistances by linking low‐ and high‐frequency phonons, boosting phonon transport through the interface. Engineered interfaces enhance heat spreading from the channel/junction and rule out premature failure.

Malakoutian, Mohamadali↗

150K - 200K miniature pulse tube cooler for micro satellites

Air Liquide is working with the CNES and Steel électronique in 2013 to design, manufacture and test a Miniature Pulse Tube Cooler (MPTC) to cool infrared detectors for micro-satellite missions. The cooler will be particularly adapted to the needs of the CNES MICROCARB mission to study atmospheric Carbon Dioxide which presents absorption lines in the thermal near infrared, at 1.6 μm and 2.0 μm. The required cooler temperature is from 150 to 200K with cooling power between 1 and 3 watts. The overall electrical power budget including electronics is less than 20W with a 288-300K rejection temperature. Particular attention is therefore paid to optimizing overall system efficiency. The active micro vibration reduction system and thermal control systems already developed for the Air Liquide Large Pulse Tube Cooler (LPTC) are currently being implemented into a new high efficiency electronic architecture. The presented work concerns the new cold finger and electronic design. The cooler uses the compressor already developed for the 80K Miniature Pulse Tube Cryocooler. This Pulse Tube Cooler addresses the requirements of space missions where extended continuous operating life time (>5 years), low mass and low micro vibration levels are critical.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

1366 Project Automate: Enabling Automation for <$0.10/W High-Efficiency Kerfless Wafers Manufactured in the US

For photovoltaic (PV) manufacturing to thrive in the U.S., there must be an innovative core to the technology. Project Automate builds on 1366’s proprietary Direct Wafer® kerfless wafer technology and aims to unlock the cost and efficiency advantages of thin kerfless wafers. Direct Wafer is an innovative, U.S.-friendly (efficient, low-labor content) manufacturing process that addresses the main cost barrier limiting silicon PV cost-reductions – the 35-year-old grand challenge of manufacturing quality wafers (40% of the cost of modules) without the cost and waste of sawing. This simple, scalable process will allow 1366 to manufacture “drop-in” replacement wafers for the $10 billion silicon PV wafer market at 50% of the cost, 60% of the capital, and 30% of the electricity of conventional casting and sawing manufacturing processes. This SolarMat project developed the Direct Wafer processes’ unique capability to tailor the shape of wafers to simultaneously make thinner AND stronger wafers (with lower silicon usage) that enable high-efficiency cell architectures. By producing wafers with a unique target geometry including a thick border (which determines handling characteristics) and thin interior regions (which control light capture and electron transport and therefore determine efficiency), 1366 can simultaneously improve quality and lower cost (using less silicon).

14 SOLAR ENERGY↗

Tailoring Electron-Photon Interaction in Active 3D Photonic-Crystal Architectures

A photonic-crystal is an artificially engineered periodic structure. It is often referred to as an “optical semiconductor” due to its unparallel capability to mold the flow-of-light on-chip, not only in plane (the x-y plane) but also along the third direction. Examples of the unique 3D control-of-light include diffraction less light-guiding, slow light, super prism, negative refraction and high-Q cavity. A new research frontier exists in which the concept of complete control-of-light is utilized to facilitate and maximize electron-photon interaction. The close proximity and strong interaction between a photonic-crystal and an electronic medium can lead to new optoelectronic properties not easily attainable by other means. In this program, we will study this new class of active photonic-crystal and to achieve improved device performances and basic discoveries. Under this program, the PI has made significant progress in the following areas: (i) We have maximized light trapping and absorption by a 3D simple-cubic photonic-crystal; By advancing the concept of simple-cubic symmetry design, we have successfully designed a super thin-film architecture for high efficiency, crystalline silicon solar cells; Most recently, we have provided a theoretical roadmap for thin-film silicon solar cells with 30% power conversion efficiency. (ii) In the modification of thermal radiation area, we have observed quasi- optical coherence in thermal radiation from a 3D metallic photonic-crystal; Furthermore, we have made a direct confirmation of super-Planckian radiation a tungsten photonic-crystal; (iii) We have made simultaneous observation of a large light diffraction-efficiency, 82%, and efficiency enhancement by a volume hologram material (PQ-PMMA) for solar concentration application. (iv) we have also successfully fabricated a 3D metal-oxide photonic crystal. We demonstrated that this TiO 2 photonic crystal can achieve an effectively infinite optical path-length created using a simple-cubic photonic crystal for extreme light trapping.

36 MATERIALS SCIENCE↗

Layered semiconductor neutron detectors

Room temperature operating solid state hand held neutron detectors integrate one or more relatively thin layers of a high neutron interaction cross-section element or materials with semiconductor detectors. The high neutron interaction cross-section element (e.g., Gd, B or Li) or materials comprising at least one high neutron interaction cross-section element can be in the form of unstructured layers or micro- or nano-structured arrays. Such architecture provides high efficiency neutron detector devices by capturing substantially more carriers produced from high energy .alpha.-particles or .gamma.-photons generated by neutron interaction.

47 OTHER INSTRUMENTATION↗

High Efficiency Solar Power via Separated Photo and Voltaic Pathways

This project demonstrates a novel nanostructured solar cell architecture capable of achieving high efficiency levels that is relatively simple and inexpensive to manufacture. The high efficiency will be achieved by the novel structure that separates the path of the photons from the path of the generated charge carriers. In this way, the photon path can be long for maximum light absorption, while the path for carriers can be short for maximum electronic energy harvesting. The combination of maximum light absorption coupled with maximum carrier harvesting is the basis for the expected high efficiency. The project will develop high efficiency solar cell prototypes utilizing this unique nanostructured architecture. The project addresses the fundamental limitation inherent in all current solar cell designs, and which opens a pathway to development for high efficiency solar cells at low cost. Realizing this goal will result in a levelized cost of electricity in the range of 10¢/kWh, which would achieve the long-sought goal of making photovoltaic electricity cost competitive with fossil-fuel generated electricity without any governmental subsidies. This breakthrough would spur the already rapid growth in the photovoltaic industry to an explosive pace, with significant, widespread benefit to the national economy and the nation’s energy security. The initial target of the program is to develop single-junction solar cells using ultrathin amorphous silicon with the performance approaching that of single crystal silicon cells.

14 SOLAR ENERGY↗