Search NASA⌕ Search

SEARCH · Search NASA

Results for “high entropy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

High Density of Strong yet Deformable Intermetallic Nanorods Leads to an Excellent Room Temperature Strength-Ductility Combination in a High Entropy Alloy

This paper introduces a new microstructural template for high entropy alloys (HEAs), where the face centered cubic (FCC) complex concentrated solid solution is reinforced with a high density of strong, yet deformable, nanorods of an ordered multi-component intermetallic L12 compound. Thermodynamic modeling has been employed to design this HEA with a large L12 volume fraction. Thermo-mechanical processing by isothermal annealing of the conventionally processed bulk cold-rolled alloy directly at precipitation temperatures, has been applied to produce a high density of uniformly distributed L12 nanorods within refined FCC grains, resulting from concomitant recrystallization and discontinuous precipitation processes. The nanorod morphology of the discontinuous L12 product has been established from three-dimensional atom probe tomography. The refined grains result in a complete coverage of the microstructure with discontinuously precipitated intermetallic nanorods. This nanorod strengthened HEA exhibits an exceptionally high room temperature yield strength of ~1630 MPa, good tensile ductility of ~15%, and an ultimate tensile strength of ~1720 MPa. Furthermore, a single L12 phase alloy, melted based on the precipitate composition in the two-phase FCC + L12 HEA, exhibits very high compressive deformability and strain hardenability, unusual for ordered intermetallic compounds. These results open a new strategy for design of fine-grained microstructures strengthened via ordered intermetallic phases, exploiting the beneficial effects of discontinuous precipitation, for achieving very high room temperature tensile strengths while maintaining good ductility.

Gwalani, Bharat↗
DOE OSTI2021

Enhancing fatigue life by ductile-transformable multicomponent B2 precipitates in a high-entropy alloy

Catastrophic accidents caused by fatigue failures often occur in engineering structures. Thus, a fundamental understanding of cyclic-deformation and fatigue-failure mechanisms is critical for the development of fatigue-resistant structural materials. Here we report a high-entropy alloy with enhanced fatigue life by ductile-transformable multicomponent B2 precipitates. Its cyclic-deformation mechanisms are revealed by real-time in-situ neutron diffraction, transmission-electron microscopy, crystal-plasticity modeling, and Monte-Carlo simulations. Multiple cyclic-deformation mechanisms, including dislocation slips, precipitation strengthening, deformation twinning, and reversible martensitic phase transformation, are observed in the studied high-entropy alloy. Its improved fatigue performance at low strain amplitudes, i.e., the high fatigue-crack-initiation resistance, is attributed to the high elasticity, plastic deformability, and martensitic transformation of the B2-strengthening phase. This study shows that fatigue-resistant alloys can be developed by incorporating strengthening ductile-transformable multicomponent intermetallic phases.

36 MATERIALS SCIENCE↗
DOE OSTI2026

A Comparative Study of Thermal Oxidization Resistance of a High-Entropy Metal Boride and a High-Entropy Metal Carbide

We present a systematic study of thermal oxidation resistance of transition metal borides and carbides up to 1300 °C in a dry air environment. A High-Entropy Metal Boride (HEMB), of composition (Hf 0.2 , Mo 0.2 , Nb 0.2 , Ta 0.2 , Zr 0.2 )B 2 , and a similar High-Entropy Metal Carbide (HEMC) (Hf, Mo, Nb, Ta, Zr)C 5 were synthesized from precursor mixtures, under 30 MPa of pressure at a temperature of 1800 °C using a Spark Plasma Sintering Device. The synthesized phases were confirmed via X-ray Diffraction analysis, which showed a pure hexagonal AlB 2 -type structure for HEMB and a face-centered cubic (FCC) structure for HEMC, with lattice parameters, a = 3.10 Å and c = 3.37 Å for HEMB and a = 4.524 Å for HEMC. Oxidation resistance was evaluated using a simultaneous thermogravimetric analysis and differential scanning calorimetry (TGA/DSC) stage in which HEMB and HEMC were heated up to 1300 °C at a rate of 2 °C/min in a dry air environment. Scanning electron microscopy (SEM) was used to analyze the resulting oxidized material. Our study demonstrates that HEMB shows better thermal oxidation resistance as compared to a similar metal composition HEMC at high temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A topological kagome magnet in high entropy form

AbstractTopological kagome magnets RMn 6 Sn 6 (R = rare earth element) attract numerous interests due to their non-trivial band topology and room-temperature magnetism. Here, we report a high entropy version of kagome magnet, (Gd 0.38 Tb 0.27 Dy 0.20 Ho 0.15 )Mn 6 Sn 6 . Such a high entropy material exhibits multiple spin reorientation transitions, which is not seen in all the related parent compounds and can be understood in terms of competing magnetic interactions enabled by high entropy. Furthermore, we also observed an intrinsic anomalous Hall effect, indicating that the high entropy phase preserves the non-trivial band topology. These results suggest that high entropy may provide a route to engineer the magnetic structure and expand the horizon of topological materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Nanolamellar phase transition in an additively manufactured eutectic high-entropy alloy under high pressures

Much is unknown about how phase transitions link to micro-/nano-structures in high-entropy systems, especially under extreme pressure and temperature conditions. This work studies the evolution of dual-phase nanolamellar eutectic high-entropy alloy phases of AlCoCrFeNi 2.1 generated by laser powder-bed fusion (L-PBF) for pressures up to 42 GPa. We compare quasi-hydrostatic high pressure synchrotron x-ray diffraction studies on L-PBF printed cylindrical samples up to 5.5 GPa (large-volume Paris–Edinburgh cell) to those carried out on an L-PBF printed foil in a diamond anvil cell where the pressure reached 42 GPa. Our results show that the initially alternating face-centered cubic (FCC) and body-centered cubic (BCC) nanolamellar structure of AlCoCrFeNi 2.1 transformed into single-phase FCC nanolamellae under high pressure with BCC–FCC phase transformation completion at 21 ± 3 GPa. Our results indicate a diffusionless BCC–FCC transformation in this additively manufactured far-from-equilibrium microstructure and demonstrate that the FCC phase is stable up to very high pressures. The measured equation of state for the FCC phase of AlCoCrFeNi 2.1 is presented up to 42 GPa and shows excellent agreement between the data obtained in large-volume press and diamond anvil cell experiments.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mechanical behavior and shear band of a powder-metallurgy-fabricated CoCrFeMnNi high-entropy alloy during high strain-rate deformation

High-entropy alloys (HEAs) fabricated by powder metallurgy are considered to exhibit extremely-great potential application values in the field for high-speed impact deformation due to their uniform microstructures and compositions. The mechanical behavior of a powder-metallurgy-fabricated (PM) CoCrFeMnNi HEA was investigated at room temperature with strain rates ranging from 1200 s -1 to 2800 s -1 . It was found that the serration behavior and shear localization of the alloy under dynamic conditions occurred. Results also indicated that the serrated flow took place in the PM CoCrFeMnNi HEA during mechanical deformation at high strain rates (>1000 s -1 ) and became more pronounced as the strain rate increased. Furthermore, it was determined that the yield-strength values of the PM CoCrFeMnNi HEA were sensitive to strain rates, where the values increased from 500 MPa to 700 MPa when the strain rates increased from 1200 s -1 to 2800 s -1 . Shear bands with a width of about 20 μm were generated in the PM CoCrFeMnNi HEA after the shear stress reached a maximum value of 635 MPa, which corresponded to a nominal strain of about 8.71. Nanotwins and ultrafine-equiaxed grains with a diameter of about 150 nm also developed at the core of the shear band during deformation. The results revealed that the strength of the shear band was much higher than that of the matrix grain. Nanotwins in the shear band were composed of a single face-centered-cubic (FCC) structure with the twin plane of ($\bar{1}$1$\bar1$), which could be formed via a rotational dynamic recrystallization (RDR).

36 MATERIALS SCIENCE↗
DOE OSTI2021

Nanostructured Oxide-Dispersion-Strengthened CoCrFeMnNi High-Entropy Alloys with High Thermal Stability

A nanostructured oxide-dispersion-strengthened (ODS) CoCrFeMnNi high-entropy alloy (HEA) is synthesized by a powder metallurgy process. The thermal stability, including the grain size and crystal structure of the HEA matrix and oxide dispersions, is carefully investigated by X-ray diffraction (XRD) and electron microscopy characterizations after annealing at 900 °C. The limited grain growth may be attributed to Zener pinning of yttria dispersions that impede the grain boundary mobility and diffusivity. The high hardness is caused by both the fine grain size and yttria dispersions, which are also retained after annealing at 900 °C. In this study, it is implied that the combination of ODS and HEA concepts may provide a new design strategy for the development of thermally stable nanostructured alloys for extreme environments.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Structural damage and phase stability of Al 0.3 CoCrFeNi high entropy alloy under high temperature ion irradiation

In this study, an initially single phase high entropy alloy (HEA) Al 0.3 CoCrFeNi was irradiated by 3 MeV Au ions to a fluence of 6 × 10 15 cm –2 (~31 dpa at damage peak) at four different temperatures ranging from 250 °C to 650 °C. Transmission electron microscopy (TEM) and Atom probe tomography (APT) were employed to study the evolution of structural damage and phase stability with irradiation temperature. Al 0.3 CoCrFeNi exhibited a similar evolution of irradiation-induced defects with temperature as compared with conventional FCC alloys. At 250 °C and 350 °C, most of the visible irradiation-induced defects were faulted 1/3$\langle{111}\rangle$ dislocation loops. As the irradiation temperature increased to 500 °C, perfect 1/2$\langle{110}\rangle$ dislocation loops were observed along with the faulted loops. At the highest irradiation temperature 650 °C, only dislocation lines and networks could be observed. Regarding phase stability, the 3 MeV Au irradiation was observed to suppress the precipitation of (Ni, Al)-enriched nano clusters and the L12 ordered structure at irradiation temperatures 250 °C to 500 °C whereas precipitation of the B2 ordered structure was accelerated at 650 °C. This resulted in qualitatively opposite precipitation behavior between the ion irradiated damage region and unirradiated region at 500 °C and 650 °C. The opposite phase stability of the ion-irradiated damage region and unirradiated region at different temperatures is attributed to the competing effects of ballistic dissolution vs irradiation enhanced diffusion on precipitation.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Controlling Exsolution Dynamics in High‐Entropy Oxides for Highly Active and Selective Acetylene Semi‐Hydrogenation

Exsolution-derived catalysts feature robust metal–support interactions that enhance catalytic performance; yet achieving precise control over exsolution dynamics in multicomponent oxides remains challenging. In this study, we demonstrate that exsolution behavior in high-entropy oxides (HEOs) can be rationally tuned through coupled lattice- and valence-engineering to create a highly active and selective catalyst for acetylene semi-hydrogenation. Incorporation of Li + into a rock salt-structured HEO (LiNiMgCuZnCoO x and LiHEO) induces local lattice distortion, generates oxygen vacancies, and partially oxidizes Co sites from Co 2+ to Co 3+ , collectively modulating local charge redistribution. This strategy enables facilitated Cu nanoparticle exsolution and alters the exsolution sequence from Cu 0 > Ni 0 > Co 0 in pristine HEO to Cu 0 > Co 0 > Ni 0 in the LiHEO. The resulting catalyst via controlled exsolution exhibits superior activity and ethylene selectivity, outperforming state-of-the-art transition metal systems. This work establishes entropy-enabled lattice and valence engineering as a facile route to programmable exsolution for enhanced catalysis.

36 MATERIALS SCIENCE↗
DOE OSTI2022

What is in a name: Defining “high entropy” oxides

High entropy oxides are emerging as an exciting new avenue to design highly tailored functional behaviors that have no traditional counterparts. Study and application of these materials are bringing together scientists and engineers from physics, chemistry, and materials science. The diversity of each of these disciplines comes with perspectives and jargon that may be confusing to those outside of the individual fields, which can result in miscommunication of important aspects of research. In this Perspective, we provide examples of research and characterization taken from these different fields to provide a framework for classifying the differences between compositionally complex oxides, high entropy oxides, and entropy stabilized oxides, which is intended to bring a common language to this emerging area. We highlight the critical importance of understanding a material’s crystallinity, composition, and mixing length scales in determining its true definition.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Bulk and element-specific magnetism of medium-entropy and high-entropy Cantor-Wu alloys

Magnetic Compton scattering, x-ray magnetic circular dichroism spectroscopy, and bulk magnetometry measurements are performed on a set of medium- (NiFeCo and NiFeCoCr) and high-entropy (NiFeCoCrPd and NiFeCoCrMn) Cantor-Wu alloys. The bulk spin momentum densities determined by magnetic Compton scattering are remarkably isotropic, and this is a consequence of the smearing of the electronic structure by disorder scattering of the electron quasiparticles. Nonzero x-ray magnetic circular dichroism signals are observed for every element in every alloy indicating differences in the populations of the majority and minority spin states implying finite magnetic moments. When Cr is included in the solid solution, the Cr spin moment is unambiguously antiparallel to the total magnetic moment, while a vanishingly small magnetic moment is observed for Mn, despite calculations indicating a large moment. Some significant discrepancies are observed between the experimental bulk and surface magnetic moments. Furthermore, despite the lack of quantitative agreement, the element-specific surface magnetic moments seem to be qualitatively reasonable.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

High-entropy alloys with high strength

The disclosure provides high strength high-entropy alloys with compositions (in atomic %) of Fe a Ni b Mn c Al d Cr e C f where 37-43 atomic %, b is 8-14 atomic %, c is 27-33 atomic %, d is 4-10 atomic %, e is 10-14 atomic %, and f is 0-2 atomic %.

Wu, Margaret↗