Search NASA⌕ Search

SEARCH · Search NASA

Results for “high pressures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Digital Valve for High Pressure High Flow Applications

To address the challenges, which are involved with the development of flow control valves that can meet the requirements of deep oil wells such as high pressure, high flow rate, limited power and limited space, the authors have conceived a novel design configuration [1]. This design consists of a digitalized flow control valve with multipath and multistage pressure reduction structures. Specifically, the valve is configured as a set of parallel flow paths from the inlet to the outlet. A choke valve controls the total flow rate by digitally opening different paths or different combination of the paths. Each path is controlled by a poppet cap valve basically operated in on-off states. The number of flow states is 2N where N is the number of flow paths. To avoid erosion from sand in the oil and high speed flow, the seal area of the poppet cap valve is located at a distance from the flow inlet away from the high speed flow and the speed is controlled to stay below a predefined erosion safe limit. The path is a multistage structure composed of a set of serial nozzles-expansion chambers that equally distribute the total pressure drop to each stage. The pressure drop of each stage and, therefore, the flow speed at the nozzles and expansion chambers is controlled by the number of stages. The paths have relatively small cross section and could be relatively long for large number of stages and still fit in the strict annular space limit of a typical downhole region of an oil well. The paper will present the design configuration, analysis and preliminary test results.

downhole↗
NASA NTRS2019

NtGCM User's Manual: 1.1 (High Pressure High Temperature Laser based) Nanotube Growth Chamber Monitor

This manual describes the installation and use of NtGCM software. NtGCM is software designed for monitoring the growth of nanotubes in a high temperature and high pressure chamber using a laser*. NtGCM software monitors a dozen dierent parameters that are important to understanding the growth of the nanomaterials including the laser input power, the temperature at eight separate locations inside and outside the growth chamber, as well as the pressure and ow rate of the gaseous media that control the environment in the chamber. The measurements are all made in real time. The program features a robust user account management layer and a rich data display manager that allows plotted data, displayed units and other parameters to be changed on the y for the operator's convenience.

Sauti, Godfrey↗
NASA NTRS1977

High pressure, high temperature transducer

The pressure measurement system utilizes two bourdon tubes with an active side connected to a test specimen and a reference side connected to an outside source. The tubes are attached to a single extensometer measuring relative displacement. The active side deflects when gases vent a specimen failure. The reference side is independently pressurized to a test pressure and provides a zero reference while providing a pressure calibration reference for the active side. The deflection noted by the active side at specimen failure is duplicated on the reference side by venting until an appropriate magnitude of pressure versus deflection is determined. In this way the pressure which existed inside the specimen prior to failure can be determined.

Vrolyk, John J.↗
NASA NTRS1998

Three-Dimensional Measurements of Fuel Distribution in High-Pressure, High- Temperature, Next-Generation Aviation Gas Turbine Combustors

In our world-class, optically accessible combustion facility at the NASA Lewis Research Center, we have developed the unique capability of making three-dimensional fuel distribution measurements of aviation gas turbine fuel injectors at actual operating conditions. These measurements are made in situ at the actual operating temperatures and pressures using the JP-grade fuels of candidate next-generation advanced aircraft engines for the High Speed Research (HSR) and Advanced Subsonics Technology (AST) programs. The inlet temperature and pressure ranges used thus far are 300 to 1100 F and 80 to 250 psia. With these data, we can obtain the injector spray angles, the fuel mass distributions of liquid and vapor, the degree of fuel vaporization, and the degree to which fuel has been consumed. The data have been used to diagnose the performance of injectors designed both in-house and by major U.S. engine manufacturers and to design new fuel injectors with overall engine performance goals of increased efficiency and reduced environmental impact. Mie scattering is used to visualize the liquid fuel, and laser-induced fluorescence is used to visualize both liquid and fuel vapor.

Hicks, Yolanda R.↗
NASA NTRS1976

A high pressure, high temperature combustor and turbine-cooling test facility

A new test facility is being constructed for developing turbine-cooling and combustor technology for future generation aircraft gas turbine engines. Prototype engine hardware will be investigated in this new facility at gas stream conditions up to 2480 K average turbine inlet temperature and 4.14 x 10 to the 6th power n sq m turbine inlet pressure. The facility will have the unique feature of fully automated control and data acquisition through the use of an integrated system of mini-computers and programmable controllers which will result in more effective use of operating time, will limit the number of operators required, and will provide built in self protection safety systems. The facility and the planning and design considerations are described.

Cochran, R. P.↗
DOE OSTI2025

High-pressure high-temperature melting and recrystallization of nanolamellar high-entropy alloys

Additively manufactured (AM) High Entropy Alloys (HEAs) are notable for their exceptional high-yield strength and large tensile ductility. The nanolamellar Eutectic HEA (EHEA) AlCoCrFeNi 2.1 was fabricated by laser powder bed fusion (L-PBF) in the as-printed form (EHEA1) and subsequently annealed at 1000oC (EHEA2) and 600oC (EHEA3) to achieve a broad range of mechanical properties. EHEA2 and EHEA3 samples were studied using Scanning transmission electron microscopy (STEM), energy dispersive X-ray diffraction (EDXRD) at high-pressures and high temperatures, nanoindentation hardness and modulus measurements. According to EDXRD EHEA2 and EHEA3 are composed of B2 and L1 2 phases. High-pressure high-temperature EDXRD studies show melting for EHEA2 at 1698 ± 25 K at a pressure of 6.5 GPa and melting for EHEA3 at 1598 ± 25 K at a pressure of 5.8 GPa. Post-melt and recrystallized samples were recovered at ambient conditions, and XRD analysis showed retention of B2 and L1 2 phases, although a new σ phase appeared for both EHEA2 and EHEA3 samples due to high-pressure and high-temperature melting and recrystallization experiment. SEM analysis also demonstrated the preservation of the nanolamellar morphology. Nanoindentation studies revealed that recrystallized EHEAs retain their original mechanical property hierarchy, with EHEA3 being 47% harder than EHEA2, largely related to higher content of B2-phase and retention of nanolamellar morphology. We also present Pressure-Volume-Temperature (P-V-T) data for 3-D printed and annealed eutectic high entropy alloys and extract mechanical and thermal properties data.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Study of high pressure and high current arcs in the cathode region of an arc heater

This paper investigates the behavior of high pressure, high current arcs in the downstream electrode region (cathode) of an arc heater. Computations are done for operating pressures in the range 50 atm to 200 atm and load currents in the range 6000 amp to 18,000 amp. At high pressures, due to the high current carrying capability of the dense gas, spot size remains reasonably small even for high load currents. Its value is 1.1 mm for a 50 atm arc with a load current of 18,000 amp. By increasing pressure it can be reduced further. Smaller spot size may allow us to design thinner electrode rings. Spot temperatures are high enough to cause ablation of the electrode material. In order to reduce material ablation at very high currents, the operating pressure must also be high and the arc should be rotated.

Durgapal, Prabha↗
DOE OSTI2024

High-pressure high-temperature synthesis and characterization of B 10 C

The boron-rich boron carbide materials have been traditionally synthesized by adding boron powder to B 4 C material and subjecting it to hot pressing sintering for materials composition containing 8.8–20 at. % carbon in boron (composition range of B 10.4 C to B 4 C). Our study explores a synthesis route for B 10 C starting from high-purity boron and carbon and direct conversion under high pressure and high temperature (HPHT) conditions of 2000 °C and 6–8 GPa. Synthesis was verified via x-ray diffraction analysis, showing the conversion of the high-purity boron and carbon powder mixture into a hexagonal B 10 C structure (R-3m space group) with lattice parameters of a = b = 5.6115 Å and c = 12.197 Å. The concentration of boron was measured through x-ray photoelectron spectroscopy, confirming the B 10 C ratio. The measured nanoindentation mean hardness of B 10 C was 40 GPa. Raman spectroscopy of the HPHT synthesized sample shows characteristic vibrational breathing modes of boron icosahedron and an additional intense band at a vibrational frequency of 380 cm –1 . This Raman band, which appears notably weaker in earlier studies and B 4 C samples, is assigned to the linear chain of B–B–B and attributed to the maximal incorporation of boron within the hexagonal structure.

36 MATERIALS SCIENCE↗
NASA NTRS1993

Studies on droplet evaporation and combustion in high pressures

High pressure droplet evaporation and combustion have been studied up to 15 MPa under normal and microgravity fields. From the evaporation studies, it has been found that in the supercritical environments, the droplet evaporation rate and lifetime take a maximum and a minimum at an ambient pressure over the critical pressure. Its maximum and minimum points move toward the lower ambient pressures if the ambient temperature is increased. It has been found from the combustion studies that the burning life time takes a minimum at an ambient pressure being equal to the critical pressure. It is attributable to both the pressure dependency of the diffusion rate and the droplet evaporation characteristics described above.

Sato, J.↗
DOE OSTI2025

Electronic Spin Relaxation and Clustering in High-Pressure High-Temperature Synthesized Microcrystalline Diamond Particles with Reduced Nitrogen Content

The negatively charged nitrogen-vacancy (NV – ) color center in diamonds is widely studied because of numerous applications of this unique quantum system in sensing and quantum information sciences. While substitutional nitrogen is required to form the NV – centers in diamond, it also yields other paramagnetic defects─primarily the neutrally charged substitutional nitrogen centers (P1)─that decrease NV – spin coherence, which in turn degrades performance in applications. Herein, we investigate high-pressure high-temperature synthesized diamond microparticles (ca. 140–185 μm) having lower─ranging from 3 to 38 ppm─than the typical nitrogen content of type 1b diamond ( ca. 100 ppm and higher) typically used for the production of fluorescent diamond particles with NV – centers. A suite of electron paramagnetic resonance, optically detected magnetic resonance, and nuclear magnetic resonance methods are used to characterize spin properties of P1 and NV – centers in the particles. Upon decreasing the nitrogen content from 29 to 3 ppm, the ensemble NV – T 2 relaxation time increased by about 3-fold as measured directly in the Hahn Echo experiment at magnetic field of 1.2 T. Analysis of electronic relaxation of P1 centers revealed the existence of at least two distinct populations of P1 centers, consisting of fast and slower relaxing spins and allowed for an estimation of local concentrations. Even with <10 ppm nitrogen contents, the analysis indicated a highly heterogeneous distribution of P1 centers, suggesting the possibility of P1 spin clustering even at low nitrogen concentrations. The combined data demonstrate that the particles prepared from HPHT diamond with a low nitrogen content offer improved spin properties that are beneficial for NV – sensing applications.

Carbon↗
DOE OSTI2024

Dual-phase superconductivity in high-pressure high-temperature synthesized TaNbZrHfTi

We report on a novel TaNbZrHfTi-based high entropy alloy (HEA) which demonstrates distinctive dual-phase superconductivity. The HEA was synthesized under high pressures and high temperatures starting from a ball milled mixture of elemental metals in a large-volume Paris–Edinburgh cell with P ≈ 6 GPa and T = 2300 K. The synthesized HEA is a phase mixture of BCC (NbTa)0.45(ZrHfTi)0.55 with Tc1 = 6 K and FCC (NbTa)0.04(ZrHfTi)0.96 with Tc2 = 3.75 K. The measured magnetic field parameters for the HEA are lower critical field, Hc1(0) = 31 mT, and a relatively high upper critical field, Hc2(0) = 4.92 T. This dual-phase system is further characterized by the presence of a second magnetization peak, or the fishtail effect, observed in the virgin magnetization curves. This phenomenon, which does not distort the field-dependent magnetization hysteresis loops, suggests intricate pinning mechanisms that could be potentially tuned for optimized performance. The manifestation of these unique features in HEA superconductivity reinforces phase-dependent superconductivity and opens new avenues in the exploration of novel superconducting materials.

Materials Science↗
NASA NTRS2012

Real-Time, Non-Intrusive Detection of Liquid Nitrogen in Liquid Oxygen at High Pressure and High Flow

An integrated fiber-optic Raman sensor has been designed for real-time, nonintrusive detection of liquid nitrogen in liquid oxygen (LOX) at high pressures and high flow rates in order to monitor the quality of LOX used during rocket engine ground testing. The integrated sensor employs a high-power (3-W) Melles Griot diode-pumped, solid-state (DPSS), frequency-doubled Nd:YAG 532- nm laser; a modified Raman probe that has built-in Raman signal filter optics; two high-resolution spectrometers; and photomultiplier tubes (PMTs) with selected bandpass filters to collect both N2 and O2 Raman signals. The PMT detection units are interfaced with National Instruments Lab- VIEW for fast data acquisition. Studies of sensor performance with different detection systems (i.e., spectrometer and PMT) were carried out. The concentration ratio of N2 and O2 can be inferred by comparing the intensities of the N2 and O2 Raman signals. The final system was fabricated to measure N2 and O2 gas mixtures as well as mixtures of liquid N2 and LOX

Singh, Jagdish P.↗
NASA NTRS1986

Determination of the relative resistance to ignition of selected turbopump materials in high-pressure, high-temperature, oxygen environments, volume 1

Advances in the design of the liquid oxygen, liquid hydrogen engines for the Space Transportation System call for the use of warm, high-pressure oxygen as the driving gas in the liquid oxygen turbopump. The NASA Lewis Research Center requested the NASA White Sands Test Facility (WSTF) to design a test program to determine the relative resistance to ignition of nine selected turbopump materials: Hastelloy X, Inconel 600, Invar 36, Monel K-500, nickel 200, silicon carbide, stainless steel 316, and zirconium copper. The materials were subjected to particle impact and to frictional heating in high-pressure oxygen.

Stoltzfus, Joel M.↗
DOE OSTI2024

Sound Velocities of Stishovite at Simultaneous High Pressure and High Temperature Suggest an Eclogite‐Rich Layer Beneath the Hawaii Hotspot

Compressional and shear wave velocities of polycrystalline stishovite (SiO 2 ) have been measured at simultaneous high pressures and temperatures up to 14.5 GPa and 800°C. By fitting velocities to the finite strain equations, the elastic moduli and density were determined to be K S0 = 306.6(46) GPa, $K$$^{′}_{S}$ = 4.92(10), ∂K S /∂T = −0.024(1) GPa/K, G 0 = 229.0(34) GPa, G′ = 1.07(10), ∂G/∂T = −0.017(1) GPa/K, ρ 0 = 4.287(2) g/cm 3 . Our modeling suggested that, in the eclogite, coesite-stishovite transition can increase P and S wave velocities by 2.4% and 3.5%, respectively. A comparison between geophysical observations and our model shows that the coesite-stishovite phase transition in the eclogite can potentially be responsible for the occurrence of the X discontinuity beneath Hawaii. In addition, our current results suggest an eclogite-rich layer between 340 and 450 km depth beneath Hawaii. The eclogite concentration at the top and bottom of the layer is 41–55 vol% and >77 vol%, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Electrical Conductivity and Sound Velocities of Talc Under High Pressure and High Temperature Conditions and Application to the Subducting Cocos Plate

Talc is expected to be an important water carrier in Earth's upper mantle, and understanding its electrical and seismic properties under high pressure and temperature conditions is required to detect possible talc-rich regions in subduction zones imaged using geophysical observations. Here, we conducted acoustic and electrical experiments on natural talc aggregates at relevant pressure-temperature conditions. Compressional wave velocity (V p ) was measured using ultrasonic interferometry in a Paris-Edinburgh press at pressures up to 3.4 GPa and temperatures up to 873 K. Similar Vp values are obtained regardless of the initial crystallographic preferred orientation of the samples, which can be explained by talc grain reorientation during the experiment, with the (001) plane becoming perpendicular to the uniaxial compression axis. Electrical conductivity of the same starting material was determined using impedance spectroscopy in a multi-anvil press up to 6 GPa and 1263 K. Two conductivity jumps are observed, at ∼860–1025 K and ∼940–1080 K, depending on pressure, and interpreted as talc dehydroxylation and decomposition, respectively. Electrical anisotropy is observed at low temperature and decreases with increasing pressure (∼10 at 1.5 GPa and ∼2 at 3.5 GPa). Comparison of acoustic and electrical results with geophysical observations in central Mexico supports the presence of a talc-bearing layer atop the subducted Cocos plate.

Cocos plate↗