Bioderived ether design for low soot emission and high reactivity transport fuels
This study developed the design principle of bio-derived ether fuels with low soot emission and high reactivity based on an experiment-theory combined approach.
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This study developed the design principle of bio-derived ether fuels with low soot emission and high reactivity based on an experiment-theory combined approach.
Aluminum nitride thin films were deposited by reactive high power impulse magnetron sputtering (HiPIMS) and pulsed direct-current on Si (100) and textured Mo substrates, where the same deposition conditions were used for both techniques. The films were characterized by x-ray diffraction and atomic force microscopy. The results show a pronounced improvement in the AlN crystalline texture for all films deposited by HiPIMS on Si. Already at room temperature, the HiPIMS films exhibited a strong preferred (002) orientation and at 400 °C, no contributions from other orientations were detected. Despite the low film thickness of only 200 nm, an ω-scan full width at half maximum value of 5.1° was achieved on Si. The results are attributed to the high ionization of sputtered material achieved in HiPIMS. On textured Mo, there was no significant difference between the deposition techniques.
The shock-compression response of Ni + Al multilayered thin foils is investigated using laser-accelerated thin-foil plate-impact experiments over the pressure range of 2 to 11 GPa. The foils contain alternating Ni and Al layers (parallel but not flat) of nominally 50 nm bilayer spacing. The goal is to determine the equation of state and shock-induced reactivity of these highly reactive fully dense thin-foil materials. The laser-accelerated thin-foil impact set-up involved combined use of photon-doppler-velocimetry to monitor the acceleration and impact velocity of an aluminum flyer, and VISAR interferometry was used to monitor the back free-surface velocity of the impacted Ni + Al multilayered target. The shock-compression response of the Ni + Al target foils was determined using experimentally measured parameters and impedance matching approach, with error bars identified considering systematic and experimental errors. Meso-scale CTH shock simulations were performed using real imported microstructures of the cross-sections of the multilayered Ni + Al foils to compute the Hugoniot response (assuming no reaction) for correlation with their experimentally determined equation of state. It was observed that at particle velocities below ∼150 m/s, the experimentally determined equation of state trend matches the CTH-predicted inert response and is consistent with the observed unreacted state of the recovered Ni + Al target foils from this velocity regime. At higher particle velocities, the experimentally determined equation of state deviates from the CTH-predicted inert response. A complete and self-sustained reaction is also seen in targets recovered from experiments performed at these higher particle velocities. The deviation in the measured equation of state, to higher shock speeds and expanded volumes, combined with the observation of complete reaction in the recovered multilayered foils, confirmed via microstructure characterization, is indicative of the occurrence of shock-induced chemical reaction occurring in the time-scale of the high-pressure state. TEM characterization of recovered shock-compressed (unreacted) Ni + Al multilayered foils exhibits distinct features of constituent mixing revealing jetted layers and inter-mixed regions. These features were primarily observed in the proximity of the undulations present in the alternating layers of the Ni + Al starting foils, suggesting the important role of such instabilities in promoting shock-induced intermetallic-forming reactions in the fully dense highly exothermic multilayered thin foils.
In this work, a high-valent manganese(IV)-hydroxo porphyrin π-cation radical complex, [Mn(IV)(OH)(Porp +• )(X)] + , was synthesized and characterized spectroscopically. The Mn porphyrin intermediate was highly reactive in alkane hydroxylation and oxygen atom transfer reactions. More importantly, the Mn porphyrin intermediate reacted with water at a fast rate, resulting in the dioxygen evolution. To the best of our knowledge, we report the first manganese Cpd I model compound bearing a porphyrin π-cation radical ligand with a high reactivity in oxidation reactions, including water oxidation.
Fly ash, industrial lime, and an additive (calcium hypochlorite )) were used to prepare a highly reactive absorbent. Simultaneous desulfurization and denitrification were carried out in a flue gas circulating fluidized bed (CFB). The effects of influencing factors on the removal efficiencies of SO{sub 2} and NO were also investigated. Removal efficiencies of 94.5% for SO{sub 2} and 65.5% for NO were obtained under the optimal experimental conditions. The component of the spent absorbent was analyzed with chemical analysis methods. The results indicated that more nitrogen than sulfur species appeared in the spent absorbent. A scanning electron microscope (SEM) and an accessory X-ray energy spectrometer (EDS) were used to observe the microproperties of the samples, including fly ash, highly reactive absorbent, and spent absorbent. The removal products of spent absorbent were analyzed using ion chromatography and chemical analysis. The simultaneous removal mechanism of SO{sub 2} and NO based on this absorbent was proposed according to the experimental results.
One of the long-standing paradoxes in chemistry is that the molecular species of greatest interest are often highly reactive chemical intermediates and thus present only at vanishingly small concentrations under typical steady state conditions. Here, this has proven both a key frustration and powerful motivation for physical chemists in probing such species, particularly for high resolution laser spectroscopic methods in the infrared. Over the past 4-5 decades, this fundamental sensitivity challenge has stimulated the development of many novel techniques for efficient generation, cooling, and infrared probing of such transient chemical intermediates, achieving increasingly sophisticated levels of spectroscopic detail, chemical insight, and a testbed for comparison with first principles ab initio quantum calculations. Two of the pioneering contributors to this scientific arena have been George Pimentel and C. Bradley Moore, both responsible for nourishing DJN’s own enduring fascination with spectroscopic IR study of elusive chemical intermediates. This chapter is not intended to provide a comprehensive review of this large and enormously successful field, but it rather more simply attempts to capture a few selective “Moore-centric” snapshots of the Nesbitt group scientific evolution, specifically in i) advances by Pimentel for the original development of rapid scan flash kinetic spectroscopy based on spectrometers with rapidly rotating IR gratings, ii) the modernization/extension of these methods in the Moore group toward the first high resolution IR laser spectroscopy of singlet/triplet methylene 1,3 CH 2 diradical, and finally to iii) the development of slit supersonic discharge expansion methods at JILA for sub-Doppler infrared laser study of multiple radicals, jet cooled molecular ions, and highly reactive chemical intermediates.
Liquid hydrogen and aluminum trimethyl as highly reactive chemical additives in turbojet afterburner to promote fuel combustion process
Silicon oxynitride thin films were synthesized by reactive high power impulse magnetron sputtering of silicon in argon/nitrous oxide plasmas. Nitrous oxide was employed as a single-source precursor supplying oxygen and nitrogen for the film growth. The films were characterized by elastic recoil detection analysis, x-ray photoelectron spectroscopy, x-ray diffraction, x-ray reflectivity, scanning electron microscopy, and spectroscopic ellipsometry. Results show that the films are silicon rich, amorphous, and exhibit a random chemical bonding structure. The optical properties with the refractive index and the extinction coefficient correlate with the film elemental composition, showing decreasing values with increasing film oxygen and nitrogen content. The total percentage of oxygen and nitrogen in the films is controlled by adjusting the gas flow ratio in the deposition processes. Furthermore, it is shown that the film oxygen-to-nitrogen ratio can be tailored by the high power impulse magnetron sputtering-specific parameters pulse frequency and energy per pulse.
Self-assembled monolayers (SAMs) with amino tail groups are of interest due to their ability of coupling further compounds. Such groups can be, in particular, created by electron irradiation of nitro- or nitrile-substituted aromatic SAMs, which provide a basis for chemical nanolithography and the fabrication of functionalized nanomembranes. An estimate of reactivity of the created amino groups requires a reference system of homogeneous, amino-terminated aromatic SAMs, which can also be used as a highly reactive molecular template. Here, we describe the synthesis of 4′-aminobiphenyl-4-thiol (ABPT) and SAMs prepared from this precursor on Au(111). The monolayers were characterized by X-ray photoelectron spectroscopy and near edge X-ray absorption fine structure spectroscopy, which revealed that they are well defined, chemically uniform, densely packed, and highly ordered. To examine the influence of electron irradiation on the reactivity of the terminal amino groups, ABPT SAMs were exposed to low energy (50 eV) electrons up to a dose of 40 mC/cm{sup 2} and, subsequently, immersed in either trifluoroacetic, pentafluoropropionic, or heptafluorobutyric anhydride. Analysing the amount of the attached anhydride species made it possible to determine the percentage of reactive amino groups as well as the effect of steric hindrance upon the coupling reaction. The above results are compared with those obtained for the well-established nitro-substituted biphenylthiol monolayers.
Satellite observations of formaldehyde (HCHO) columns provide top-down constraints on emissions of highly reactive volatile organic compounds (HRVOCs). This approach has been used previously to constrain emissions of isoprene from vegetation, but application to US anthropogenic emissions has been stymied by lack of a discernable HCHO signal. Here we show that oversampling of HCHO data from the Ozone Monitoring Instrument (OMI) for 2005 - 2008 enables quantitative detection of urban and industrial plumes in eastern Texas including Houston, Port Arthur, and Dallas-Fort Worth. By spatially integrating the individual urban-industrial HCHO plumes observed by OMI we can constrain the corresponding HCHO-weighted HRVOC emissions. Application to the Houston plume indicates a HCHO source of 260 plus or minus 110 kmol h-1 and implies a factor of 5.5 plus or minus 2.4 underestimate of anthropogenic HRVOC emissions in the US Environmental Protection Agency inventory. With this approach we are able to monitor the trend in HRVOC emissions over the US, in particular from the oil-gas industry, over the past decade.
The influence of inert gases (Ne, Ar, Kr) on the sputter process of carbon and carbon-nitride (CN{sub x}) thin films was studied using reactive high power pulsed magnetron sputtering (HiPIMS). Thin solid films were synthesized in an industrial deposition chamber from a graphite target. The peak target current during HiPIMS processing was found to decrease with increasing inert gas mass. Time averaged and time resolved ion mass spectroscopy showed that the addition of nitrogen, as reactive gas, resulted in less energetic ion species for processes employing Ne, whereas the opposite was noticed when Ar or Kr were employed as inert gas. Processes in nonreactive ambient showed generally lower total ion fluxes for the three different inert gases. As soon as N{sub 2} was introduced into the process, the deposition rates for Ne and Ar-containing processes increased significantly. The reactive Kr-process, in contrast, showed slightly lower deposition rates than the nonreactive. The resulting thin films were characterized regarding their bonding and microstructure by x-ray photoelectron spectroscopy and transmission electron microscopy. Reactively deposited CN{sub x} thin films in Ar and Kr ambient exhibited an ordering toward a fullerene-like structure, whereas carbon and CN{sub x} films deposited in Ne atmosphere were found to be amorphous. This is attributed to an elevated amount of highly energetic particles observed during ion mass spectrometry and indicated by high peak target currents in Ne-containing processes. These results are discussed with respect to the current understanding of the structural evolution of a-C and CN{sub x} thin films.
Additive manufacturing (AM) is a unique type of fabrication that builds objects layer-by-layer from virtually any feedstock. When compared to traditional, subtractive manufacturing, AM wastes less feedstock material, which makes it ideal for the shaping of magnetic materials. Furthermore, complex geometries with advanced heat and mass transport properties can be created out of highly reactive lanthanides which could not be created with traditional manufacturing. This work describes the results of shaping these materials into high-resolution microchannel geometries via additive manufacturing and the resulting characteristics of the printed artifacts.
A mononuclear non-heme manganese(IV)-oxo complex has been synthesized and characterized using various spectroscopic methods. The Mn(IV)-oxo complex shows high reactivity in oxidation reactions, such as C-H bond activation, oxidations of olefins, alcohols, sulfides, and aromatic compounds, and N-dealkylation. In C-H bond activation, the Mn(IV)-oxo complex can activate C-H bonds as strong as those in cyclohexane. It is proposed that C-H bond activation by the non-heme Mn(IV)-oxo complex does not occur via an oxygen-rebound mechanism. The electrophilic character of the non-heme Mn(IV)-oxo complex is demonstrated by a large negative ρ value of ~4.4 in the oxidation of para-substituted thioanisoles.
We perform spectroscopic surface characterization on mesoporous ceria (CeO 2 ) under exposure of sarin gas, also known as GB. We find mesoporous CeO 2 displays extraordinary reactivity towards GB dissociation under high vacuum. The spectroscopic results combined with density functional theory (DFT) calculations suggest that the cleavage of the P–F and P–OR bonds are both possible pathways for GB to dissociate on the CeO 2 surfaces. The modeling reveals differences in dissociation pathways of GB on the crystallographic (111)- and (110)-surfaces of ceria. Here we also report some dissociation of GB on mesoporous CeO 2 under ambient conditions. The finding that mesoporous CeO 2 can degrade GB under mild conditions is encouraging and implies the strong potential of ceria-based materials to be applied in combating chemical warfare agents related to the GB series.
Highly crystalline anatase TiO 2 nanosheets, made by controlled oxidation of TiS 2 nanosheets, expose the {001} and {100} facets, giving rise to enhancement in HER as compared to Degussa P25 TiO 2 nanoparticles. No enhancement in ORR was observed.
Lithium-ion batteries (LIBs) are central to the urgent societal need to decarbonize both transportation and energy storage on the grid. Unfortunately, despite their attractive energy/power density, as well as high coulombic and energy efficiencies, further improvement of this technology – especially their durability – is desperately needed. To support these efforts, our study focuses on fundamental understanding of the decomposition pathways for LIB electrolytes at the cathode–electrolyte interface (CEI), as the nature of these reactions directly controls the extent to which cell capacity and voltage decays in these systems. In this study, we employ electrochemical methods, coupled with product analysis using NMR spectroscopy and mass spectrometry, to determine the decomposition mechanisms in both model and technologically relevant electrolytes. Remarkably, we discovered the electrochemical formation of protons with high chemical activity, comparable to known superacids, at potentials relevant to practical Li-ion batteries. Their reactivity toward every individual component of the CEI provides a unified thermochemical origin for a myriad of side reactions that are commonly associated with the electrochemical reaction. In particular, electrochemically generated protons react with intact EC molecules to form CO 2 and other short and long chain ethers. They also undergo an acid–base reaction with LiPF 6 , to form the weaker acid HF, and with the cathode active material, leaching transition metals into the electrolyte. Collectively, the results of this study all point to the urgent need to either mitigate this proton formation or introduce benign harvesting additives via new electrolyte design strategies.
In this study, the impacts of fuel volatility and reactivity on combustion stability and emissions were studied in a light-duty single-cylinder research engine for a three-injection catalyst heating operation strategy with late post-injections. Here, N-heptane and blends of farnesane/2,2,4,4,6,8,8-heptamethylnonane were used to study the impacts of volatility and reactivity. The effect of increased chemical reactivity was also analysed by comparing the baseline #2 diesel operation with a pure blend of mono-ether components (CN > 100) representative of potential high cetane oxygenated bioblendstocks and a 25 vol.% blend of the mono-ether blend and #2 diesel with a cetane number (CN) of 55. At constant reactivity, little to no variation in combustion performance was observed due to differences in volatility, whereas increased reactivity improved combustion stability and efficiency at late injection timings. Fuels with higher reactivity were found to reduce engine-out hydrocarbon and carbon monoxide emissions while also achieving stable combustion at post-injection timings later than those achievable with #2 diesel fuel. The pure ether blend had the latest achievable post-injection timing of +30.5 CAD while still maintaining stable combustion (coefficient of variation of gross-indicated mean effective pressure < 5%). With post-injection timing adjusted to achieve a matched exhaust temperature of 300 °C, the ether-diesel CN 55 blend was observed to have slightly higher thermal efficiency in comparison to the baseline #2 diesel fuel. The results also indicate that cetane number may serve as a good indicator of combustion characteristics at late injection timings used for aftertreatment thermal management operation.