Search NASA⌕ Search

SEARCH · Search NASA

Results for “high-surface-area”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Experimental characterization of a triply periodic minimal surface PCM-to-air thermal energy storage device

Here, the expansion of energy production has intensified research into thermal energy storage (TES) to manage variability and improve system efficiency. Heat exchanger design is critical to achieving high power densities in TES systems. This study presents a high-surface-area phase change material (PCM)-to-air heat exchanger fabricated via resin-based stereolithography with a novel gyroid-based geometry tailored for enhanced performance. Material properties of the commercial PCM and resin were characterized using analytical techniques. A controlled air loop was used to evaluate heat transfer and pressure drop at various flow rates and inlet temperatures. Results show a strong dependence on the inlet temperature difference (ΔT) relative to the PCM melting point. During charging at the highest flow rate, increasing the inlet air temperature from ΔT = 5 °C to 20 °C above the melting point increased the average heat transfer rate by 187%. During discharging, decreasing the inlet temperature by the same ΔT below the melting point led to a 232% increase. Notably, the high-surface-area design enabled nearly symmetric charging and discharging behavior, a novel result for PCM-based TES systems which are often restricted by natural convection and other effects. The overall heat transfer coefficient was calculated and compared to values from standard design correlations. The maximum thermal effectiveness reached 95% at ΔT = 20 °C and a moderate flow rate of 34 m 3 /h. Peak coefficients of performance (COP) of 7 during charging and 6.4 during discharging were observed at ΔT = 20 °C and a low flow rate of 20 m 3 /h. These results demonstrate the viability of additively manufactured geometries for advanced TES applications.

25 ENERGY STORAGE↗
DOE OSTI2025

Demonstration of MgCr 2– x Mn x O 4 Spinel Oxide Cathodes in High-Voltage Mg Batteries

Solid-solution oxide spinels with high redox voltages and facile Mg 2+ mobility have been identified as promising candidates for practical, high-voltage cathodes in Mg batteries. In this work, we discuss the development of MgCr 2-x Mn x O 4 [x = 0.5, 1, 1.2] solid-solution spinel oxides as a cathode material and their electrochemical performance paired with an Mg anode in a full cell. This work presents the first demonstration of full cells with these materials. Mg-Cr-Mn spinel oxides with varying Cr and Mn contents were synthesized using alternative synthetic routes for optimal electrochemical performance. High-resolution synchrotron powder X-ray diffraction (PXRD), solid-state nuclear magnetic resonance (NMR) spectroscopy, and electron microscopy showed that these different synthetic routes resulted in changes in structures and particle morphologies, which in turn affect the electrochemical performance. Particularly, the urea coprecipitation synthetic route resulted in high-surface-area particles that enabled lower overpotentials and increased discharge capacity. The high surface area also resulted in expedited structural degradation caused by the irreversible migration of Mg 2+ into normally vacant 16c sites in the spinel lattice. This structural degradation was lessened by using a hydrosauna-urea synthesis method, which decreased the Mg/Mn inversion ratio while retaining high-surface-area particles with good cycling performance. Furthermore, our findings highlight the necessity for high surface area or nanostructured spinel oxide cathodes with minimized Mg-Mn inversion to enable spinel oxide cathodes in Mg full cells.

Mg anode↗
DOE OSTI2025

1,10-Phenanthroline-Iron Complex-Derived Fe-N-C Electrocatalysts: Enhanced Oxygen Reduction Activity and Stability Through Synthesis Tuning

The development of electrocatalysts composed of earth-abundant elements is essential for advancing the commercial application of Proton Exchange Membrane Fuel Cells (PEMFC). Among these, single-atom electrocatalysts, such as Fe-N-C, show great promise for the oxygen reduction reaction (ORR). This study aims to improve the ORR activity and stability of Fe-N-C electrocatalysts by fine-tuning the straightforward 1,10-phenanthroline-iron complexation synthesis method. Key parameters, including iron-to-phenanthroline ratio, carbon powder surface area, and pyrolysis temperature were systematically varied to evaluate their influence on the resulting electrocatalysts. The findings of this study revealed that the electrocatalysts synthesized with 1,10-phenanthroline (Phen) and high-surface-area Black Pearls (BP) possessed much better ORR activity than electrocatalysts prepared by using Vulcan carbon (lower surface area). Interestingly, electrocatalysts prepared with BP, but with a non-bidentate nitrogen-containing ligand molecule, such as imidazole, showed a much poorer activity, as the resulting material predominantly consisted of inactive structures, such as encapsulated iron nanoparticles and iron oxide, as evidenced by HR-TEM, EXAFS, and XRD. Therefore, the results suggest that only the synergistic combination of the bidentate ligand phenanthroline (Phen) and the high-surface-area carbon support (BP) favored the formation of ORR-active Fe-N-C single-atom species upon pyrolysis. The study also unveiled a significant enhancement in electrocatalyst stability during accelerated durability tests (and air storage) as the pyrolysis temperature was increased from 700 to 1300 °C, albeit at the expense of ORR activity, likely resulting from the generation of iron particles. Pyrolysis at 1050 °C yielded the electrocatalyst with the most favorable balance of activity and stability in rotating disk measurements, while maintaining moderate durability under PEM fuel cell operation. The insights obtained in this study may guide the development of more active efficient and durable electrocatalysts, synthesized via a simple method using earth-abundant elements, for application in PEMFC cathodes.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2025

Constructing Highly Durable Fuel Cell Catalysts Through Integrating Graphitic Shell‐Protected Composite Carbon Support with Gaseous Co Deposition‐Driven PtCo Intermetallics

Metal dissolution, nanoparticle agglomeration, and carbon support corrosion cause significant performance degradation of current PtCo catalysts under acidic and oxidative oxygen reduction reaction. Here, in this study, an integrated strategy is presented to design high-performance Pt 3 Co intermetallic catalysts by regulating gaseous Co deposition-driven diffusion into Pt nanoparticles supported on a composite carbon. The composite carbon is derived from ZIF-8/polyaniline, consisting of a high-surface-area (HSC) core and a protective graphitic shell (GS), which is employed to design 40 wt.% Pt/HSC@GS catalyst. The corresponding membrane electrode assemblies (MEAs) can maintain 1.09 A cm −2 at 0.7 V (20. 7% loss) after 10 000 cycles (1.0–1.5 V for carbon stability) and 1.15 A cm −2 (16.1% loss) after 150 000 cycles (0.60–0.95 V for catalyst stability). A ordered Pt 3 Co intermetallic is synthesized via a gaseous Co-deposition process, which yields a homogeneous Co-rich layer onto the Pt nanoparticles on the composite support, thereby facilitating Co diffusion into Pt crystal during subsequent ordering annealing to form the ordered intermetallic structure. This gaseous deposition leads to a thin carbon layer on PtCo nanoparticles, inhibiting particle growth during the annealing and mitigating Co dissolution under dynamic electrochemical conditions. The PtCo catalyst achieves impressive MEA performance and long-term durability (1.45 A cm −2 at 0.7 V after 120 000 cycles) under heavy-duty conditions.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2026

The presence of Ru metal modifies the behavior of deuterium bound to pyridinic nitrogen in doped graphene-like materials

We used a combination of x-ray photoelectron spectroscopy (XPS) and density functional theory (DFT) to investigate how the presence of a ruthenium (Ru) metal substrate modifies the N-D bond strength of the pyridinic nitrogen species in nitrogen (N)-doped graphene (Gr) on Ru(0001) compared to metal-free highly-oriented pyrolytic graphite (HOPG) substrate. The N-dopants were introduced through low-energy N+/N2+ irradiation. N is embedded in the carbon materials in two predominant configurations: as graphitic N (GN: N substituted in the hexagonal C lattice) and pyridinic N (PN: substitutional N adjacent to a C vacancy). XPS data showed that upon atomic deuterium (D) exposure at 220 K, the PN peak shifted to a higher binding energy by +1.2 eV for HOPG and +1.0 eV for N-doped graphene on Ru(0001), while the GN peak remained unchanged, indicating that the D atoms bound solely to pyridinic N. 85% of PN sites on HOPG can be saturated with D atoms, whereas only ~30% of pyridinic N sites are able to bind D atoms in N-doped Gr/Ru(0001). Our DFT analysis shows that this difference is due to the coordination of PN to Ru atoms, which necessitates bond cleavage of the N-Ru interaction prior to D atom adsorption. D begins desorbing from N-HOPG at ~573 K and is fully desorbed by ~973 K, whereas desorption from N-doped graphene on Ru(0001) begins at ~290 K, with complete desorption observed at ~700 K, indicating that the Ru metal weakens the N-D bond strength. We also studied a high-surface-area, layered, and porous N-doped carbon material, internally labeled NC900, which was synthesized by pyrolysis of glucose and graphitic carbon nitride (g-C3N4) at 1173 K. D exposure caused a +1.1 eV PN peak shift in NC900, with no change in the GN peak. Moreover, the NC900 exhibited the same desorption behavior as HOPG, demonstrating that well-defined model systems can effectively capture the behavior of more complex N-doped carbon materials.

Alupothe Gedara, Buddhika S.↗
DOE OSTI2025

Synthesis of multicomponent oxygen evolution reaction coatings via block copolymer templating with vapor- and solution-phase precursors

Porous mixed transition metal oxide heterostructures are promising electrocatalysts due to their high surface area. However, achieving conformal multicomponent oxide coatings with controlled nanoscale architectures remains challenging. Here, we report a synthesis strategy that integrates solution-based swelling infiltration (SBI) with gas-phase sequential infiltration synthesis (SIS) in a block copolymer template to fabricate porous, high-surface-area, conformal mixed-oxide electrocatalytic coatings. In this approach, a PS75-P4VP25 block copolymer (BCP) film is first infiltrated with transition metal acetylacetonate precursors via SBI, followed by exposure to gas phase precursors of ZnO via SIS process. Thermal annealing of the infiltrated BCP films converts them into all-inorganic Fe–ZnO, Fe–Co–ZnO, and Fe–Ni–ZnO coatings. Electrochemical testing on 70 nm thick conformal coatings demonstrates promising oxygen evolution reaction (OER) activity in alkaline media, with mass-specific current densities up to 1.0 × 10 5 mA/g at an overpotential of 330 mV (vs. RHE) at ultralow loading (~0.005 g/cm 2 ). Among the compositions, Fe–Co–ZnO and amorphous Fe–Ni–ZnO show the best OER performance, delivering current densities of 2.00 and 3.04 mA/cm 2 , respectively, compared to 1.52 mA/cm 2 for Fe–ZnO.. This work establishes SBI–SIS as a versatile route for fabricating nm-thin, high-performance multicomponent oxide heterostructures on cost-efficient supports, enabling efficient catalyst utilization in electrochemical energy conversion application.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Mesoporous Thin Film Architectures: Addressing Material Demands through Molecular Self-Assembly

Mesoporous thin films spark interest across a wide range of disciplines due to their tunable nanostructures, large internal surface areas, and strong compatibility with planar optical, electronic, and microfluidic devices. While attention in the porous materials community has shifted toward macroporous or disordered nanoporous systems, a resurgence in mesoporous thin film research is underway, driven by new molecular self-assembly methods, advanced materials chemistry, and improved characterization techniques. The integration of high-χN block copolymer design, kinetically persistent micelle templating, and postdeposition processing protocols now allows control over structural parameters such as pore size, wall thickness, porosity, and connectivity. These advances have overcome many of the thermodynamic and processing constraints that previously limited widespread adoption. Rather than serving only as high-surface-area supports, mesoporous thin films are engineered as active interfaces where responsive chemistries and nanoscale confinement act in tandem. Embedding switchable ligands, thermoresponsive polymers, redox mediators, or ion-selective groups directly within the pore walls enables real-time control over transport, optical, and electrochemical properties. These capabilities open up new directions in adaptive coatings, gated membranes, and fast-response biosensors. To further expand their functional scope, mesoporous films are integrated into hierarchical and multicomponent architectures. Techniques such as triblock terpolymer templating, crack-directed assembly, and nanoimprint lithography allow for control over spatial organization on the micron and submicron scale and pore system orientation. This enables programmable anisotropy, enhanced molecular diffusion, and wavelength-selective photonic behavior, essential for next-generation sensing, catalysis, and energy applications. Such structural and functional complexity requires equally sophisticated characterization. Multimodal and in situ techniques can track material dynamics under operational conditions. Recent progress includes extended-range ellipsometric porosimetry (EP) for hierarchical architectures, vacuum EP for interface energetics, time-resolved EP for diffusion kinetics, and correlative AFM-SAXS mapping. The introduction of advanced neutron-based spectroscopies, particularly quasielastic neutron scattering (QENS), promises to provide real-time access to ion transport dynamics and segmental motion under nanoscale confinement, offering a path toward deeper mechanistic understanding of structure-performance correlations in mesoporous systems. This Account reflects the technical advances made and the interdisciplinary collaborations that have shaped our collective vision. The particular dimensions of mesopores enable us to subtly tune interactions at the molecular, interfacial, and mesoscopic levels that permit us to harness nanoconfinement. What emerges is a versatile, modular platform capable of chemical gating, energy transduction, and sensing with a level of tunability unmatched by other porous materials. We highlight critical challenges including the need for more robust large-area processing, a deeper understanding of dynamic behavior under cycling, and better integration with device-level architectures. Our strategies support the transition of mesoporous thin films into active high-performance components in next-generation energy, environmental, and biomedical systems.

oxides↗
DOE OSTI2025

NiAl–MoO 2 S 2 Nanoparticles: Structural Evolution and Mechanistic Insights into High-Performance Selenium Oxyanion Removal across Diverse pH Conditions

Advancing sorbent materials for the selective removal of toxic oxyanions from water requires synthetic control, tunable chemistry, and an atomic-level understanding of structure–function relationships. Here, we report the synthesis and detailed characterization of NiAl–MoO 2 S 2 , a novel layered double hydroxide (LDH) nanomaterial designed for the efficient sequestration of selenium oxoanions (SeO 3 2– and SeO 4 2– ) from complex aqueous environments. The material is synthesized through a room-temperature ion-exchange process, wherein interlayer NO 3 – anions in NiAl–LDH are replaced with MoO 2 S 2 2– clusters, forming high-surface-area, flower-like nanoparticles. Comprehensive structural analysis using the synchrotron X-ray pair distribution function, X-ray absorption spectroscopy, and X-ray photoelectron spectroscopy reveals a distinct chemical transformation of intercalated [MoO 2 S 2 ] 2– into [Mo 2 O 2 S 6 ] 2– -like clusters, generating redox-active interlayers that drive selenium capture. This tailored interfacial chemistry underpins the material’s exceptional sorption performance, achieving distribution coefficients (K d ) ≥ 10 6 mL/g and maximum capacities of 343 mg/g for SeO 4 2– and 514 mg/g for SeO 3 2– , outperforming state-of-the-art inorganic sorbents. Importantly, NiAl–MoO 2 S 2 maintains high selectivity and capacity across acidic, neutral, and alkaline pH, efficiently removing selenium from ppm to sub-10 ppb trace levels, even in the presence of competing ions typical of natural and industrial waters. The selenium uptake proceeds via reductive precipitation coupled with the oxidation of molybdenum and sulfide within the LDH framework. This study highlights the power of strategic synthetic modification and interlayer functionalization in LDHs to unlock new structural motifs and redox chemistries, offering a scalable route to advanced materials for environmental remediation.

Adsorption↗
DOE OSTI2025

Sequential Infiltration Synthesis (SIS) of In 2 O 3 -Based Porous Photoelectrodes for Molecular Sensitization

High-surface-area photoelectrodes are highly desirable for solar energy conversion applications, particularly in systems where surface-bound molecular chromophores are responsible for light absorption. To this end, porous Indium-Zinc-Oxide (IZO) frameworks are fabricated via Sequential Infiltration Synthesis (SIS) into poly(methyl methacrylate) (PMMA) films followed by air annealing. A more complete understanding of the multimetal infiltration process conditions and postannealing temperature allows for precise control of zinc (Zn) incorporation to afford porous, conductive, transparent, and amorphous photoelectrodes. Uniform incorporation of both indium (In) and Zn is found to require extended diethylzinc (DEZ) exposures to compensate for remarkably slow precursor diffusion in the presence of indium oxyhydroxide nuclei. SIS-fabricated IZO photoelectrodes are structurally robust, electrochemically active, and exhibit dye adsorption that suggest practical surface area enhancements greater than 100×. In conclusion, these attributes establish SIS as a rapid, scalable, and reproducible route to photoelectrodes for solar energy conversion and hybrid interface characterization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Single Metal Atom Catalysts Prepared by Diluted Atomic Layer Deposition

The scalable and facile preparation of single-atom catalysts remains a critical challenge. Here, in this study, we introduce diluted atomic layer deposition (DALD), a unique approach for synthesizing supported metal catalysts with precisely tunable loadings. Unlike conventional metal deposition by ALD which uses pure metal precursors, DALD employs a diluted precursor mixture, combining organometallic precursors with the corresponding free ligand in controlled ratios. The method enables precise control over metal loadings, allowing the synthesis of structures ranging from nanoparticles to isolated single atoms, as exemplified by Ir, Rh, and Pt on high-surface-area γ-Al 2 O 3 . With its inherent simplicity and exceptional efficiency in metal precursor utilization, DALD represents a highly scalable strategy, unlocking opportunities for integrating single-atom catalysts into industrial processes.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Supported Organochromium Ethylene Oligomerization Enabled by Surface Lithiation

Here, in this work, supported organochromium ethylene polymerization catalysts have been tuned to mediate ethylene oligomerization via surface lithiation, which provides a generalizable protocol to control stereoelectronics and redox states of surface organometallic active sites. The homoleptic chromium(IV) alkyl complex Cr(CH 2 SiMe 3 ) 4 was grafted on high-surface-area anatase titania (TiO 2 ) nanoparticles as well as on silica to produce Cr/TiO 2 and Cr/SiO 2 , respectively. Treatment of these materials with excess n-butyllithium led to the reduced chromium complexes Cr/Li x TiO 2 and Cr/Li/SiO 2 , each of which still retains one hydrocarbyl ligand on chromium. A set of heterogeneous complexes were studied by electron paramagnetic resonance and X-ray absorption spectroscopy, which indicate a reduction in the oxidation state of the major chromium species to Cr II upon lithiation. Cr/Li x TiO 2 converts ethylene to hexenes with a high selectivity (>80%), which was persistent over 10 days at 80 °C, achieving >950 turnovers. The exclusive formation of C 4 and C 6 olefins, preferring the trimerization product, without a statistical (Flory–Schulz) distribution is characteristic of the oxidative cyclization oligomerization mechanism rather than the traditional Cossee–Arlman mechanism, whereas Cr/Li/SiO 2 produced a mixture of trimerization and polymerization products, suggesting site heterogeneity in the silica-based material. On the other hand, the unreduced chromium(IV) materials as well as low lithium-containing Cr/Li x TiO 2 (x < 0.16) exclusively produced ultrahigh molecular weight polyethylene, determined by differential scanning calorimetry and gel permeation chromatography analysis, likely formed via a linear-insertion mechanism, with a crossover from the polymerization to oligomerization regime observed at ~16% Li intercalation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Metal–Oxide Interface Sites Created Using Atomic Layer Deposition and Tested for CO Oxidation

The performance of catalysts made out of Pt supported on TiO 2 thin films grown on SBA-15 (a silica mesoporous material) by atomic layer deposition (ALD) was characterized systematically by combining in situ infrared absorption spectroscopy (IR) with other techniques including electron microscopy and adsorption−desorption isothermal measurements. The titania films in the resulting high-surface-area catalysts were evenly distributed throughout the inner surface of the SBA-15 mesopores, and their thickness could be controlled at a submonolayer level, with 3 to 4 TiO 2 ALD cycles needed for the complete coverage of the silica sites. The titania films could be deposited either before or after adding the metal (Pt), which was dispersed in the form of small nanoparticles (NPs) approximately 4−6 nm in diameter, in order to exert some control on the density and nature of the Pt/TiO 2 interface sites. One important lesson deriving from this work is that such an order of deposition leads to significantly different catalysts in spite of the fact that most of their structural properties are similar. If the Pt is deposited on the titania films, the resulting metal NPs are slightly smaller than those grown on silica and display CO adsorption sites with lower surface Pt coordination numbers. On the other hand, when TiO 2 is deposited on the Pt/SBA-15 starting material, some titania grows on the metal and partially blocks its surface while also creating new interface sites where CO binds more weakly and displays lower C−O stretching frequencies. In terms of catalytic performance, the results from in situ IR CO site titration and kinetic measurements combined suggest a mechanism where CO first adsorbs on Pt atop sites and then migrates to Pt/TiO 2 interface sites, where oxidation takes place. Both types of sites appear to be similar in all the catalysts tested, but catalytic performance could be optimized by tuning their surface densities. Maximum catalytic activity was obtained when the TiO2 films were deposited first and with TiO 2 coverages of at least half a monolayer, that is, after at least 2 ALD cycles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Unveiling the Origin of Morphological Instability in Topologically Complex Electrocatalytic Nanostructures

Coarsening and degradation phenomena in metals have largely focused on thermally driven processes, such as bulk and surface diffusion. However, dramatic coarsening has been reported in high-surface-area, nanometer-sized Pt-based catalysts during potential cycling in an electrolyte at room temperature─a temperature too low for the process to be explained purely by surface mobility values measured in both vacuum and electrolytes (∼10 –22 and ∼10 –18 cm 2 /s, respectively). This morphological evolution must be due to a different mechanism for mass transport that is sensitive to electrochemical conditions (e.g., electrolyte composition, potential limits, and scan rate). However, there have been no notable studies of electrochemically induced coarsening in nanometer-sized electrocatalysts. Here, we unveil the origins of coarsening in an electrolyte through coupled in situ experiments and atomistic kinetic Monte Carlo (kMC) simulations. Our work demonstrates electrochemical coarsening is driven by two concurrent mechanisms that can be explained at the atomistic level: (i) dissolution/redeposition during the reduction of an oxidized species and (ii) rapid surface diffusion of undercoordinated atoms.

gold↗
DOE OSTI2026

Thermodynamic Control of Interface Directs MnO 2 Nucleation Chemistry for Dense and Conformal Electrodeposition

Manganese dioxide (MnO 2 ) is widely recognized as a promising material for high-energy-density energy storage systems due to its broad applicability and facile electrodeposition. However, achieving uniform, thin, and high-mass-loading MnO 2 coatings on high-surface-area electrodes remains a significant challenge. Conventional electrodeposition methods typically yield nonuniform, thick layers with poor conductivity and limited material utilization, restricting their practical use. Here, we uncover a thermodynamically engineered vanadyl/pervanadyl (VO 2+ /VO 2 + ) interface that fundamentally reshapes MnO 2 electrodeposition chemistry, enabling highly uniform and dense coatings. Here, combining in situ AFM measurement, Classical Nucleation Theory, and Johnson–Mehl–Avrami–Kolmogorov modeling, we show that this interface reduces early-stage detectable MnO 2 island size by 35-fold and shifts the MnO 2 growth from diffusion-limited to reaction-limited progressive nucleation. This thermodynamically controlled interface yields highly dense and conformal MnO 2 films with record-high mass loading of 241 mg cm –2 (1607 mg cm –3 ) on 3D-printed graphene aerogels, without compromising porosity or inducing thickness gradient. As a prototype demonstration, the resulting MnO 2 electrodes deliver record-setting volumetric performance in both capacitors (106 F cm –3 ) and Zn//MnO 2 pouch cells (162 mAh cm –3 ). Beyond energy storage, our findings demonstrate the significance of thermodynamic interface control in MnO 2 nucleation chemistry for achieving dense and uniform coatings on various substrates, with implications for electrocatalysis, semiconductor processing, and advanced materials manufacturing.

Batteries↗
DOE OSTI2025

Tungsten-dioxo single-site heterogeneous catalyst on carbon: synthesis, structure, and catalysis

This study investigates the application of a novel third-row metal, tungsten, to carbon-supported single-site metal-oxo heterogeneous catalysis. Tungsten is a green and earth-abundant metal, but an unexplored candidate in this role. The carbon (AC = activated carbon)-supported tungsten dioxo complex, AC/WO 2 was prepared via grafting of (DME)WO 2 Cl 2 (DME = 1,2-dimethoxyethane) onto high-surface-area activated carbon. AC/WO 2 was fully characterized by ICP-OES, XPS, EXAFS, XANES, SMART-EM, and DFT. W 4d 7/2 XPS and W L III -Edge XANES assign the oxidation state as W(VI), while EXAFS reveals two W=O double and two W–O single bonds at distances of 1.73 and 1.92 Å, respectively. These data align well with DFT computational results, supporting the structure as Carbon(–μ-O–) 2 M(=O) 2 . SMART-EM verifies that single W(VI) catalytic sites are bonded in an out-of-plane manner. The catalytic performance of air- and water-stable AC/WO 2 is compared to that of AC/MoO 2 . AC/WO 2 is more active and selective than the molybdenum analog in mediating alcohol dehydration of various substrates, and is recyclable. Notably, AC/WO 2 is an effective and recyclable catalyst for primary aliphatic alcohol dehydration and forms no dehydrogenation side products in contrast to AC/MoO 2 . However, AC/WO 2 is less effective in epoxidation and PET depolymerization. Overall, this work demonstrates the potential of carbon-supported third row metals for future studies.

02 PETROLEUM↗
DOE OSTI2025

Cobalt–niobium co-doping of indium oxide: structural and adsorption/catalytic properties for CO 2 valorization

The co-doping of the indium oxide structure with cobalt and niobium is attempted using a microemulsion method to produce high-surface-area, mesoporous, functional materials. The co-doping leads to a major nanometric bixbyite oxide phase, with both cations occupying cation positions and affecting the size and shape of the oxide entities. For specific cobalt to niobium atomic ratios, the presence of a second surface phase is encountered. Such a surface phase corresponds to an ill-defined indium hydroxide-type phase. The coexistence of the two phases is a unique phenomenon associated with the presence of both cations, which play a decisive role in promoting the CO 2 adsorption capability of the solids, as well as the valorization of the molecule under dual heat–light excitation. The co-doping of indium oxide thus appears to be a unique way to intensify the analogous thermal (classical) catalytic process for the elimination/valorization of carbon dioxide.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Activating magnetite ores for aqueous ironmaking at high current densities

Low-temperature electrochemical cells reducing iron oxides to metal in alkaline electrolytes can support fully electrified steelmaking processes. Previous studies on these cells have primarily focused on high-surface-area hematite, Fe 2 O 3 , reactants whereas attempts to reduce suspensions of magnetite, Fe 3 O 4 —one of the two feedstocks for existing ironmaking reactors—have generally been limited to low rates of reaction (<30 mA cm −2 ). Here, in this study, we control the crystalline domain size of Fe 2 O 3 and Fe 3 O 4 particles in 10 M NaOH electrolytes to study how the nanoscale morphology of oxides controls the rate of electrochemical ironmaking. Rotating-ring disk electrode measurements of Fe 2+ , in situ Raman spectroscopy of the electrode surface, and ex situ electron microscopy were consistent with a hypothesized passivation process at Fe 3 O 4 surfaces that may prevent the continuous formation of soluble intermediates. Sufficiently small (<100 nm diameter) oxide particles yielded Fe partial current densities >160 mA cm −2 , a fivefold increase relative to previously reported rates for Fe 3 O 4 suspensions and comparable to active Fe 2 O 3 . Electron microscopy revealed that electrodeposited films were composed of micron-scale crystalline Fe domains with a porous film of Fe 3 O 4 nanoparticles and supports a model where Fe is grown primarily from soluble Fe 2+ intermediates. Based on these insights, inactive blast-furnace-grade iron-oxides were transformed into high surface area nanoparticles (1.6 to 229.2 m 2 g −1 ) via reprecipitation, leading to a ninefold enhancement in faradaic efficiency and an Fe partial current density of 120 mA cm −2 . When integrated with chlor-iron cells producing reagents for reprecipitation, this approach could lead to a cost-competitive process for electrochemical ironmaking from industrially relevant feedstocks.

TEM↗
DOE OSTI2025

Atomic layer deposition of nanofilms on porous polymer substrates: Strategies for success

Atomic layer deposition (ALD) is a versatile technique for engineering the surfaces of porous polymers, imbuing the flexible, high-surface-area substrates with inorganic and hybrid material properties. Previously reported enhancements include fouling resistance, electrical conductance, thermal stability, photocatalytic activity, hydrophilicity, and oleophilicity. However, there are many poorly understood phenomena that introduce challenges in applying ALD to porous polymers. In this paper, we address five common challenges and ways to overcome them: (1) entrapped precursor, (2) embrittlement, (3) film fracture, (4) deformation, and (5) pore collapse. These challenges are often interrelated and can exacerbate one another. To investigate these phenomena, we applied various ALD chemistries to porous polymers including polyethersulfone, polysulfone, polyvinylidene fluoride, and polycarbonate track-etched membranes. Reaction-diffusion modeling revealed why certain precursors and processing conditions result in embrittling subsurface material growth, entrapment of unreacted precursors, and nongrowth. We quantify the limits of ALD processing temperatures that are dictated by thermal expansion mismatch and can lead to fractured ALD films. The results herein allow us to make recommendations to avoid, mitigate, or overcome the difficulties encountered when performing ALD and plasma-enhanced ALD on porous polymers. We intend this article to serve as a “lessons learned” guide informed by previous experience to provide a better understanding of the difficulties and limitations of ALD on porous polymers and knowledge-based guidelines for successful depositions. This knowledge can accelerate future research and help experimentalists navigate and troubleshoot as they expose porous polymers to reactive precursor vapors.

36 MATERIALS SCIENCE↗