Tissue composition and higher heating values differ among six bioenergy grasses
Not provided.
Agriculture↗
SEARCH · Search NASA
Results for “higher heating value”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Redefining fuel heating value for engines: Accounting for heat of vaporization
Defining a fuel's heating value (i.e., energy content) is fundamental for calculating engine efficiency and for life cycle analysis comparisons between different fuels. Traditional definitions of lower heating value and higher heating value account for the effect of water vapor versus liquid water in the exhaust, which is important when the fuel is used in a furnace or boiler. In an engine, it is equally important to properly account for the energy required to vaporize liquid fuel. Heat of vaporization has a small effect for common hydrocarbon fuels, typically less than 1% of lower heating value, but the effect is much larger for other important fuels such as ethanol (3.4% of lower heating value) and methanol (5.9% of lower heating value). This paper defines a new type of fuel heating value that more accurately reflects the useful fuel energy content for engines. Vaporized heating value is defined as the heating value when starting with a vaporized fuel instead of a liquid fuel. It can be calculated by adding the fuel's heat of vaporization to the traditional lower heating value. This paper illustrates the rationale and benefits of using vaporized heating value using data from the literature.
09 BIOMASS FUELS↗
Improving bamboo’s fuel and storage properties with a net energy export through torrefaction paired with catalytic oxidation
Using torrefied char, or biocoal, as solid fuel provides an opportunity to introduce a sustainable feedstock into the energy market. The goals of this study were to investigate how torrefaction improves the energy content and the grindability of a Malaysian bamboo along with understanding the potential for integrated energy recovery from torrefaction gases. The feedstock was torrefied at 250–290 °C for 1 h and the combustion characteristics and grindability of the solid products along with the composition of torrefied gas species were measured. The results showed a beneficial increase in elemental carbon increased from 47 to 63 wt% at 290 °C torrefaction, reflecting an increase in higher heating value from 17.8 to 25.6 MJ/kg. The combustion behavior of all the products appeared to show three distinct combustion zones; however, torrefaction severity leading to higher combustion temperature and time as the fixed carbon augmented with the increase of torrefaction temperature. This increase in severity also lead to more friable and grindable material, and the 290 °C condition required a factor of 2.7 less hold-up time in the mill compared to the raw bamboo, and a factor of 8.5 less energy (938 and 111 kWh/tonne respectively). Through analysis of the gas and volatile formation, a case study showed that catalytic oxidation can convert nearly 100% of the embodied chemical energy into usable thermal energy. These experimental findings were scaled to a 100,000 tonne/y capacity torrefaction plant and in the moderate case of 270 °C operating temperature, the plant has 1.25 GJ/tonne excess energy beyond what the process needs.
09 BIOMASS FUELS↗
Self-powered Heating: Efficiency Analysis
Conventional fuel-fired heating devices such as furnaces, boilers, and water heaters have fuel efficiency less than 100% on the basis of higher heating value. They also require electricity from the electric grid to power parasitic loads such as blowers, pumps, fans, and ignitors. The primary energy efficiency of the device accounts for both fuel used on-site and primary energy used off-site to produce electric power used by the device. This work compares conventional fuel-fired heating devices to two types of self-powered devices. A self-powered device (SPD) integrates a power cycle onboard to eliminate consumption of grid electricity. We assume that all heat rejected by the onboard power cycle is added to the process fluid, so that, compared with a conventional device, the same amount of heat is provided to the process fluid and the same amount of fuel is consumed, but grid electricity consumption is eliminated. The first SPD type is the basic one: exactly the electricity required is generated. The second type considered is the SPD with heat pump (SPD-HP), in which the power cycle generates more electricity than needed for parasitic loads, and the excess electricity is used to power a heat pump. The heat pump extracts additional heat from the ambient to boost efficiency. Both SPD and SPD-HP self-consume all the generated electricity, in contrast to combined heat and power (CHP) systems that export electricity. In this work, equations are derived to express the efficiency of three classes of heating devices: conventional (consuming grid electricity), self-powered (consuming no grid electricity), and self-powered with heat pump. The efficiency of each is derived as a function of up to six factors: (1) the fraction of combustion heat captured, (2) the rate of parasitic power consumption, (3) the fraction of electric energy dissipated as useful heat, (4) the power cycle conversion efficiency, (5) the grid efficiency, when applicable, and (6) the heat pump COP, when applicable. Scenarios are identified in which it is possible to achieve efficiency greater than 100% on a higher heating value basis. Plausible configurations using existing technology options are outlined.
Gluesenkamp, Kyle↗
Advanced biorefinery feedstock from non-recyclable municipal solid waste by mechanical preprocessing
Because of accelerated urbanization and the development of a global economy, a large quantity of municipal solid waste (MSW) has been collected and disposed of by the municipalities. Due to this drastic increase in the disposal of MSW, the need for its management is a must to preserve the environment. Currently, approximately 50% of the total MSW generated in the United States has been utilized through various recycling, combustion, and composting technologies, which means the remaining 50% is sent to landfill; this is often known as non-recyclable MSW (nMSW). As this nMSW is physically and chemically heterogenous and contains very high amounts of inorganic material, processing is required prior to using it as a biorefinery feedstock. Thus, this study focused on how mechanical preprocessing advanced the physical and chemical properties of nMSW. The physical and chemical properties were investigated in terms of particle size distribution, bulk density, ultimate and proximate analysis, and the higher heating value (HHV). The combustion properties were examined in terms of ignition temperature, peak heat release rate, and combustion efficiency. Results showed that the variability of physical and chemical properties of nMSW can be reduced by mechanical preprocessing. For example, the variability of the bulk density of the as-received nMSW was approximately 17.3% while it reduced to 5.8% when the sample size was reduced to 2 mm. Similarly, the variability of ash and HHV reduced from 49.2% to 11.0% and 13.4%–4.2%, respectively. Combustion thermograms showed that the size reduction positively improved the combustion properties. For example, 2 mm of spec sample started to ignite approximately 4 times earlier and took 6.5 folds less time to reach the peak heating rate compared to as-received nMSW. Overall, the mechanical preprocessing reduced the variability of physical and chemical properties in addition to the improvement of combustion behavior of the nMSW which is one step forward toward the biorefinery feedstock.
09 BIOMASS FUELS↗
Hydrothermal liquefaction of Cyanidioschyzon merolae and Salicornia bigelovii Torr.: The interaction effect on product distribution and chemistry
Hydrothermal liquefaction (HTL) has proven to be a promising technology for processing wet biomass into valuable biofuel intermediates. We investigated the influence of HTL process parameters on the individual and co-liquefaction of Salicornia bigelovii Torr. (SL) and Cyanidioschyzon merolae (CM) biomass and their respective product properties and characteristics. SL and CM biomasses were subjected to HTL conditions of process temperatures (250–350 °C), 10 wt% solid loading, 30 min reaction time, and co-liquefaction ratios (80–20, 50–50, 20–80, CM-SL, respectively). The individual maximum HTL biocrude yields for CM (34.63 wt%) and SL (7.63 wt%) were obtained at 300 °C. In both cases, biocrude oils had a higher carbon and hydrogen content relative to those of the original biomass. The HHV (higher heating value) values for the biocrude samples ranged from 24.2 to 33.12 MJ/kg, which were significantly higher than those of the original biomasses. A positive synergistic effect was observed during the co-liquefaction of two biomasses, where the experimental yield of biocrude oil was higher than the theoretical value. During the co-liquefaction experiments, a maximum biocrude yield of 32.95 wt% was obtained at 300 °C and 80–20 CM-SL biomass mix ratio. Co-liquefaction led to an increase in the energy content of the co-liquefied biocrude oil and a higher energy recovery rate. Finally, the properties of HTL products and biomasses were determined with TGA, CHN elemental analyzer, GC/MS, bomb calorimeter, HACH Spectrophotometer, and ICP OES.
09 BIOMASS FUELS↗
Materials for Advanced Ultra-Supercritical (A-USC) Steam Turbines --- A-USC Component Demonstration
The U.S. Advanced Ultra-Supercritical (A-USC) Consortium was formed in 2001 as a government/industry program, sponsored by the U.S. Department of Energy (DOE) and the Ohio Coal Development Office (OCDO) and cost shared by industrial and not-for-profit partners. The purpose of the consortium was to advance the state of the art for power generation by evaluating and developing materials that allow the use of advanced steam cycles in coal-based power plants. These advanced cycles, with steam temperatures up to 1400°F (760°C), can increase the efficiency of coal-fired boilers from an average of 35% (current U.S. fleet) to more than 45% higher heating value (HHV) (>49% lower heating value [LHV]). The increase in a plant’s efficiency is limited unless new materials able to withstand these higher operating temperatures and pressures are identified and approved for use. The A-USC Consortium identified these needed materials during earlier phases of the program. It developed the welding and joining techniques along with manufacturing processes for casting and wrought products made from these new high-nickel alloys. It subjected these materials to extensive laboratory and steam loop testing. It then obtained ASME code approval for their use in U.S. boiler systems. The program’s successes leave this last remaining activity (ComTest Phase 2) that the U.S. utility industry has recommended to be accomplished prior to commercialization. The focus of the activity is the evaluation and demonstration of commercial readiness for “full scale” components to be made from these nickel-based alloy materials and provided by a U.S. domestic supply chain that is new to working with these alloys. According to studies completed by the Electric Power Research Institute (EPRI), the cost of an A-USC plant is approximately 20% higher than a non-A-USC plant because of its use of nickel-based alloys needed for the high temperature operating conditions. However, CO 2 reductions of approximately 30% from the current fleet average provide a strong incentive for its consideration. The actual costs and perceived value for CO 2 abatement will determine whether new or retrofitted plants are undertaken, although decisions to build A-USC plants in India would indicate its economic feasibility while also being part of a global carbon emissions strategy. The work by the A-USC Consortium, prior to the start of the ComTest project, has included lab scale and pilot scale materials testing, both in air and oxy-combustion. This testing has included air-cooled and steam-cooled “loops” that were installed into existing operating utility boilers to gain exposure of these materials to realistic conditions of high temperature and corrosion caused by the constituents in the coal ash. The A-USC Consortium also gained ASME Code approval of the Inconel 740 material, has cast and extruded the largest high nickel precipitation hardened alloys, and developed unique welding techniques to avoid problems identified by the competing European program. However, as valuable as these material test loops and accomplishments have been for obtaining information, their scale is below that required to minimize the risk associated for a U.S. utility to build a multibillion-dollar A-USC power plant. To reduce the final identified risk barrier to full-scale commercialization of these advanced materials and systems, the A-USC Consortium (guided by a utility industry advisory committee) has identified the key areas of the technology they desire to see as being capable of full-scale manufacturing and/or fabrication from an identified, capable U.S. domestic supplier base. A significant amount of work was accomplished during Phase 1 to identity the components, as well as the component size, that would be manufactured from advanced alloys such as Inconel 740H or Haynes 282 alloys. Pathways to supply these components for ComTest have been identified, as well as any further development that would be required. The Phase 2 effort used Phase 1 findings for designing these key full-scale components for A-USC boilers and turbines to include large castings; extrusions, forgings, fabrication of water walls and steam loops with headers from advanced materials, raw material (such as pipe extrusion billets) are at the commercial readiness level to permit advancement to a demonstration project. The Phase 2 work scope was addressed by a diverse team, including government, industry, and not-for-profit partners. The work scope under Phase 2 addressed fabrication of components identified as being outside of the proven capabilities of the existing supply chain, including the following: Steam turbine rotor forging and Haynes 282 nozzle carrier casting Superheater and reheater header and tube assemblies Large-diameter pipe extrusions and forgings Test valve articles to support ASME Code approval. In addition, key fabrication steps were completed, including boiler weld overlays and simulated field repairs. Throughout, extensive inspection and quality assurance testing of the components were performed. The team worked to advance ASME Code approval for key components and processes. Although much of the focus of ComTest Phase 2 was the high-temperature nickel-based alloy materials, a broader range of materials were incorporated, which would be representative of the materials used in full-scale A-USC power plant applications and have cross-cutting applicability on other high-temperature power generation options, such as advanced nuclear, supercritical CO 2 cycles, and central solar receivers. This report that has been submitted is organized in the following manner: Section 1 contains an Executive Summary. Section 2 discusses the ComTest project background and organization. Section 3 discusses project management and reporting. Section 4 discusses the procurement of nickel-based alloy and other A-USC materials and components. Section 5 discusses the fabrication of procurement of nickel-based alloy and other A-USC materials and components. Section 6 discusses the fabrication of cast nickel-based A-USC steam turbine components. Section 7 discusses the fabrication of forged nickel-based A-USC steam turbine piping and steam pipe components. Section 8 discusses the qualification of pressure relieve valves (PRVs) for A-USC power plants. Section 9 discusses proposed plans for future evaluation of A-USC components. Section 10 contains the summary and conclusion.
01 COAL, LIGNITE, AND PEAT↗
Low NO subx heavy fuel combustor concept program. Phase 1A: Coal gas addendum
The performance and emissions from a rich-lean combustor fired on simulated coal gas fuels were investigated using a 12.7-cm diameter axially-staged burner originally designed for operation with high heating value liquid fuels. A simple, tubular fuel injector was substituted for the liquid fuel nozzle; no other combustor modifications were made. Four test fuels were studied including three chemically bound nitrogen-free gas mixtures with higher heating values of 88, 227, and 308 kj/mol (103, 258 and 349 Btu/scf), and a 227 kj/mol (258 Btu/scf) heating value doped with ammonia to produce a fuel nitrogen content of 0.5% (wt). Stable, ultra-low nitrogen oxide, smoke-free combustion was attained for the nitrogen-free fuels. Results with the doped fuel indicated that less than 5% conversion of NH3 to nitrogen oxide levels below Environmental Protection Agency limits could be achieved. In some instances, excessive CO levels were encountered. It is shown that use of a burner design employing a less fuel-rich primary zone than that found optimum for liquid fuels would yield more acceptable CO emissions.
Rosfjord, T.↗
Preliminary appraisal of hydrogen and methane fuel in a Mach 2.7 supersonic transport
The higher heating value of hydrogen relative to JP fuel is estimated to reduce fuel weight by three fold and gross weight by 40 percent for comparable designed airplanes of equal payload and range. Engine design parameters were varied to determine the influence of lower noise goals on gross weight and direct operating cost. At current fuel prices, the DOC of a hydrogen airplane would be much higher than that of a JP airplane. A methane airplane could offer an 8.5-percent lower KOC than JP. But future shortages may escalate the prices of both JP and methane, whereas the price of hydrogen manufactured hydrolytically could be reduced from present levels. If in the future all three fuels are postulated to have equal costs per unit of energy, the DOC for hydrogen could be as much as 20 percent below that for JP on the reference 4000-nautical-mile mission. Longer ranges or lower noise requirements would improve the advantage of hydrogen.
Whitlow, J. B., Jr.↗
Pilot-Scale Pelleting Tests on High-Moisture Pine, Switchgrass, and Their Blends: Impact on Pellet Physical Properties, Chemical Composition, and Heating Values
In this study, we evaluated the pelleting characteristics of southern yellow pine (SYP), switchgrass (SG), and their blends for thermochemical conversion processes, such as pyrolysis and gasification. Using a pilot-scale ring-die pellet mill, we specifically assessed the impact of blend moisture, length-to-diameter (L/D) ratio in the pellet die, and ratio of pine to SG on the physico-chemical properties of the resulting pellets. We found that an increase in pine content by 25–50% marginally affected the bulk density; however, it also led to an increase in calorific value by 7% and a decrease in ash content by 72%. A moisture content of 25% (wet basis) and an L/D ratio of 5 resulted in poor pellet durability at <90% and bulk density values of <500 kg/m 3 , but increasing the L/D ratio to 9 and lowering the moisture content to 20% (w.b.) improved the pellet durability to >90% and the bulk density to >500 kg/m 3 . Blends with ≥50% pine content resulted in lower energy consumption, while a lower L/D ratio resulted in higher pelleting energy. Based on these findings, we successfully demonstrated the high-moisture pelleting of 2.5 ton of pine top residues blended with SG at 60:40 and 50:50 ratios. The quality of the pellets was monitored off-line and at-line by near infrared (NIR) spectroscopy. Multivariate models constructed by combining the NIR data and the pelleting process variables could successfully predict the pine content (R 2 = 0.99), higher heating value (R 2 = 0.98), ash (R 2 = 0.95), durability (R 2 = 0.94), and bulk density (R 2 = 0.86) of the pellets. Thus, we established how blending and densification of SYP and SG biomass could improve feedstock specifications and that NIR spectroscopy can effectively monitor the pellet properties during the high-moisture pelleting process.
09 BIOMASS FUELS↗
Online LIBS–ML Framework for Dynamic Characterization of Heterogeneous Waste-Derived Gasification Feedstocks
LIBS−ML framework for real time feedstock characterization during continuous conveyor transport Heterogeneous waste derived feedstocks (e.g., waste coal, biomass and blends) introduce rapid variability in heating value and ash chemistry that affect gasifier operation, yet conventional laboratory characterization techniques are too slow to support proactive control. To address this gap, this study reports on an online, in situ, dynamic characterization framework that couple’s laser-induced breakdown spectroscopy (LIBS) with leakage safe machine learning (ML) regression to deliver real time, decision quality predictions of gasifier relevant properties. A controlled sample matrix spanning two different waste coals, two different biomasses, and engineered blends under two particle size conditions were constructed and benchmarked using standardized laboratory analyses for proximate/ultimate properties and ash composition. LIBS spectra were acquired dynamically as material flowed on a conveyor belt, using high energy 1064 nm laser ablation and shot averaging to improve repeatability and precision. Supervised regression models (multi layer perceptron (MLP) /artificial neural network (ANN), random forest (RF), and support vector regression (SVR)) and an optimized weighted ensemble were trained on emission line feature sets using nested cross validation with Bayesian hyperparameter tuning and validated against an independent hold out set. The proposed LIBS−ML workflow achieves near laboratory predictive fidelity across parametric targets (including higher heating value (HHV), ash content, fixed carbon, sulfur, major ash forming oxides, and initial deformation temperature (IDT)), with the weighted ensemble providing a robust default predictor under dynamic measurement conditions. These results demonstrate a practical pathway for real time feedstock characterization that can enable feedforward adjustments and more resilient gasifier operation for variable quality waste derived fuels.
Biomass↗
One-step transformation of biomass to fuel precursors using a bi-functional combination of Pd/C and water tolerant Lewis acid
Direct one-pot transformation of lignocellulosic biomass has been developed as an effective and sustainable strategy to produce fuel blend stocks and high value chemical building blocks. In this wok, a bi-functional catalyst system consisting of palladium supported on carbon (Pd/C) and metal triflates (i.e., Sm(OTf) 3 , La(OTf) 3 , and Cu(OTf) 2 ) were shown to promote the biomass liquefaction in both hot-compressed water and supercritical ethanol medium, converting fir wood into oxygenated compounds. We report the highest bio-oil yield from hydrothermal liquefaction (HTL) was 10.47 wt% over Pd/C whereas the highest bio-oil yield of 49.71 wt% was achieved from supercritical ethanol liquefaction (SCEL) over the bi-functional catalyst system of Pd/C and La(OTf) 3 . Higher heating values, carbon recovered values and boiling point distributions were further determined for elucidating the physical properties of the bio-oils. Gas chromatography mass spectrometry (GC–MS) analysis of the bio-oils revealed the chemical composition of the bio-oils. Substituted phenols and cyclopentenone/cyclopentanone type compounds consisted of more than 60 area% of the total products from HTL, whereas phenol and esters represented the major products from SCEL. The major reaction pathways are proposed based on the GC–MS results, which include depolymerizaton, isomerization, dehydration, condensation, and hydrogenation.
09 BIOMASS FUELS↗
Pilot Testing of a Highly Efficient Pre-combustion Sorbent-based Carbon Capture System
TDA developed and demonstrated a highly efficient pre-combustion carbon capture system. The overall objective of this work was to develop a new sorbent-based pre-combustion carbon capture technology for Integrated Gasification Combined Cycle (IGCC) power plants. In this project our goal was to demonstrate the techno-economic viability of the new technology by 1) demonstrating it in large-scale slipstream tests, and 2) carrying out a high fidelity engineering and cost analysis. TDA’s process used an advanced physical adsorbent that selectively removes CO 2 from coal-derived synthesis gas above the dew point of the gas at temperatures as high as 300°C. The sorbent consists of a mesoporous carbon whose surface was grafted with functional groups that remove CO 2 via a well-known acid-base interaction. As documented in bench-scale experiments and field tests with actual coal gas, the sorbent achieved a very high capacity for CO 2 at temperatures as high as 300°C. The sorbent bound CO 2 more strongly than common physical adsorbents, providing the chemical potential needed for the high temperature operation. However, because CO 2 does not form a true covalent bond with the surface sites (as is the case with chemical absorbents), the sorbent regeneration could be carried out with only a very small energy input. The heat input to regenerate our sorbent was only 4.9 kcal per mol of CO 2 , which is much lower than that for chemical absorbents (e.g., 29.9 kcal/mol CO 2 for sodium carbonate) and was similar to the requirements of physical solvents (e.g., 4 kcal/mol CO 2 for Selexol TM ). Because the sorbent operates above the dew point of the synthesis gas (unlike the Selexol TM process), a higher power cycle efficiency can be achieved. With previous DOE/NETL funding (Contract No. DE-FE-0000469), we demonstrated the techno-economic viability of the technology in bench-scale tests and slipstream demonstrations at the National Carbon Capture Center (NCCC), Wilsonville, Alabama and Wabash River IGCC plant in Terra Haute, Indiana. We demonstrated a stable working CO 2 capacity for over 11,650 cycles with simulated synthesis gas. We also evaluated its performance with actual synthesis gas in two test campaigns at the Wabash River IGCC Plant, Terre Haute, IN and the National Carbon Capture Center (NCCC), Wilsonville, AL. The slipstream tests clearly showed that the actual coal gas constituents and potential contaminants (e.g. trace metals, halides, tars) had no effect on the sorbent’s ability to remove CO 2 (the same sorbent beds were used in both field tests with no sign of deactivation for 2,000 cycles with over 26,750 SCF of gas treated). As expected, due to the high temperature CO 2 removal capability and low energy needed to regenerate the sorbent, the power cycle efficiency with our process was greater than 34% on a higher heating value (HHV) basis; in comparison, the same IGCC plant equipped with the Selexol TM solvent for carbon capture can only achieve 31.4% HHV efficiency. The capital cost for an IGCC system with TDA’s process is estimated as $2,417/kW e , which is 12% lower than that of the IGCC/ Selexol TM process. The levelized cost for electricity including the transport, storage and monitoring (TS&M) cost for CO 2 was calculated as $\$ $92.9/MWh (lowest reported to our knowledge), which is much better than the $105.2/MWh estimated for the IGCC/ Selexol TM process. In this project (DE-FE0013105), TDA Research, in collaboration with our partners Gas Technology Institute (GTI), Illinois Clean Coal Institute (ICCI), University of California, Irvine (UCI), University of Alberta (UOA), Siemens, NCCC and Sinopec advanced the technical maturity of the technology; scaling it up by a factor of 100. We optimized the reactor design using computational fluid dynamics (CFD); using adsorption modeling we improved the pressure swing adsorption (PSA) cycle sequence. We carried out two field test campaigns with a fully-equipped 0.1 MW e prototype unit (for a total of 844 hours) using actual synthesis gas to prove the viability of the new technology. A successful 30 day (707 hrs) evaluation was completed at NCCC under air blown gasification conditions. We demonstrated 97.3% carbon capture at 1,500 SLPM, 93% carbon capture at 1,800 SLPM, and 90% carbon capture at 2,100 SLPM in the NCCC tests. We also demonstrated the system for 137 hours at a Sinopec petrochemical plant under oxygen blown gasification, demonstrating 86% carbon capture at 2,660 SLPM. In collaboration with University of California, Irvine (UCI), we completed a techno-economic analysis (TEA) for TDA’s warm gas cleanup technology integrated to IGCC power plant. The net plant efficiencies (on a coal HHV basis) for the warm gas cleanup cases were estimated to be 34.0% for E-GasTM gasifier, 34.4% for GE gasifier, 33.4 for the Shell gasifier and 34.2 for the TRIG TM gasifier (Cases 2, 4, 6 and 8 in this study) with a catalytic combustor for CO 2 purification, which are significantly higher than those for the Cold Gas Case, or an increase of as much as 12% in the heat rate for Case 2, 6% for Case 4, 9% for Case 6, and 9% for Case 8. The 1st year cost of electricity with the transport, storage and monitoring (TS&M) costs for the CO 2 included was $\$ $129.2/MWh for the E-GasTM gasifier Warm Gas Cleanup Case, $\$ $131.9/MWh for the GE gasifier Warm Gas Cleanup Case, $\$ $146.8/MWh for the Shell Gasifier Warm Gas Cleanup Case, and $\$ $129.9/MWh for the TRIG TM gasifier Warm Gas Cleanup Case. For comparison, the costs for the baseline Cold Gas CO 2 removal with Selexol for the different gasifiers were: $\$ $146.6/MWh for the E-Gas TM gasifier, $\$ $142.2/MWh for the GE gasifier, $\$ $159.0/MWh for the Shell gasifier and $\$ $144.3/MWh for the TRIG TM gasifier. In summary, the costs for our system were 7 to 12% lower than the corresponding Cold Gas Cleanup cases. The results of this techno-economic analysis suggested that TDA’s high temperature PSA-based Warm Gas Clean-up Technology can make a substantial improvement in the IGCC plant thermal performance for achieving near zero CO 2 emissions for E-Gas TM , GE, Shell and TRIG TM gasifier based IGCC power plants. The capital expenses were estimated to be lower than that of Selexol’s™. Taken together, the higher net plant efficiency and lower capital and operating costs resulted in substantial reduction in the cost of carbon capture for the IGCC plant equipped with TDA’s high temperature PSA-based carbon capture system. Finally, in collaboration with Gas Technology Institute (GTI) we completed the environmental health and safety assessment for TDA’s warm gas carbon capture technology.
01 COAL, LIGNITE, AND PEAT↗
Chapter 7.1: Microalgae
Microalgae is a unique biomass resource that does not need to compete for land and water with other biomass feedstocks because it can be cultivated on low-quality unencumbered land using noncompetitive water types including saline and wastewater. It is included as a complementary resource alongside other biomass feedstocks reported in this study, albeit at higher biomass production costs reflective of more capital-intensive farming operations than typical for terrestrial biomass. Higher biomass costs can be offset by the potential to produce value-added coproducts unique to compositional constituents of microalgae. Relative to BT16, this chapter reflects the latest analysis from the 2022 Algae Harmonization Update, which uses the latest parameterized and high-performing saline algal strain, second-generation carbon capture of point-source waste CO2 and high-pressure pipeline transport resolved to specific point-source types, saline water sourcing up to 40,000 mg/L total dissolved solids for source and makeup water salinity, blowdown water treatment and recycle, and brine disposal handling. National-scale algal biomass availability potential was calculated at 152 million tons/yr ash-free dry weight (AFDW) (191 million tons/yr dry weight) at an average biomass productivity of 26.2 g/m2 -day AFDW (about 50 tons/acre/yr dry weight).1 The algal biomass was cultivated on 3.9 million acres of multi-criteria screened and potentially available land for CONUS and fixed 268 million tons of waste CO2 based on biomass uptake. The algae biomass can be produced at an average MBSP of $674/ton AFDW ($536/ton dry weight) in 2020 dollars,2 corresponding to a total energy potential of 3.3 quads/yr at an average MBSP of $31.2/MMBtu (higher-heating-value [HHV] basis).
algae↗
Hydrogen-Steam Separation Using Mechanical Vapor Recompression Cycle
Solar thermochemical hydrogen and fuel production is a promising pathways for producing sustainable fuels and chemicals. One of the main challenges in the development of these systems is their low steam conversion extent, dictated by its restrictive thermodynamics requiring extremely high temperatures and low oxygen partial pressure to obtain conversions over 10 \%. While condensing the unreacted steam is technically simple, the latent heat is thus lost, which can be larger than the producd hydrogen higher heating value. We propose to use a modified mechanical vapor recompression cycle, allowing to recover the latent heat by compressing the steam-hydrogen mixture prior to the condensation process, thus creating a temperature different between the hot exhaust and cold inlet streams. We show that this method can recover over 90 % of the latent heat, thus increasing the viability of solar thermochemical hydrogen production cycles even under limited conversion conditions.
hydrogen technology↗
Techno-economic and life cycle analysis of synthetic natural gas production from low-carbon H 2 and point-source or atmospheric CO 2 in the United States
Synthetic natural gas (SNG) is of great interest in reducing fossil energy consumption while maintaining compatibility with existing NG infrastructure and end-use applications equipment. SNG can be produced using clean H 2 generated from renewable or nuclear energy and CO 2 captured from stationary sources or the atmosphere. In this study, we develop an engineering process model of SNG production using Aspen Plus® and production scales reported by the industry. We examine the levelized cost and life cycle greenhouse gas (GHG) emissions of SNG production under various CO 2 supply scenarios. Considering the higher cost of H 2 transportation compared with CO 2 transportation, we assume that CO 2 feedstock is transported via pipeline to the H 2 production location, which is collocated with the SNG plant. We also evaluate the cost of CO 2 captured from the atmosphere, assuming the direct air capture process can occur near the SNG facility. Depending on the CO 2 supply chain, the levelized cost of SNG is estimated to be in the range of $\$45–76$ per million British thermal units (MMBtu) on a higher heating value (HHV) basis. The SNG production cost may be reduced to $\$27–57$/MMBtu-HHV by applying a tax credit available in the United States for low-carbon H 2 production (45V). With a lower electricity price of 3¢/kWh for water electrolysis and accounting for a 45V tax credit, the SNG cost reaches parity with the cost of fossil NG. Depending on the CO 2 supply chain, SNG can reduce life cycle GHG emissions by 52–88% compared with fossil NG.
03 NATURAL GAS↗
Pathway to Complete Energy Sector Decarbonization with Available Iridium Resources using Ultralow Loaded Water Electrolyzers
We present ultralow Ir-loaded (ULL) proton exchange membrane water electrolyzer (PEMWE) cells that can produce enough hydrogen to largely decarbonize the global natural gas, transportation, and electrical storage sectors by 2050, using only half of the annual global Ir production for PEMWE deployment. This represents a significant improvement in PEMWE's global potential, enabled by careful control of the anode catalyst layer (CL), including its mesostructure and catalyst dispersion. Using commercially relevant membranes (Nafion 117), cell materials, electrocatalysts, and fabrication techniques, we achieve at peak a 250× improvement in Ir mass activity over commercial PEMWEs. An optimal Ir loading of 0.011 mg Ir cm -2 operated at an Ir-specific power of ~100 MW kg Ir -1 at a cell potential of ~1.66 V versus RHE (85% higher heating value efficiency). Here, we further evaluate the performance limitations within the ULL regime and offer new insights and guidance in CL design relevant to the broader energy conversion field.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Synergistic Effects of Inexpensive Mixed Metal Oxides for Catalytic Hydrothermal Liquefaction of Food Wastes
Industrial wastes and natural mixed oxide materials were evaluated as inexpensive heterogeneous catalysts for catalytic hydrothermal liquefaction (CHTL) of food wastes. Red mud and red clay achieved biocrude carbon yields of 47.0 and 39.5% with higher heating values (HHVs) of 40.2 and 37.7 MJ kg –1 , respectively, which were much greater than those without the catalyst (biocrude carbon yield of 19.7% and HHV of 36.1 MJ kg –1 ). Biocrude characterization revealed that similar families of molecules were formed in the presence and absence of catalysts, implying that the main role of the catalyst is to promote rates of thermal reactions, leading to biocrude production without opening new pathways. The crystalline structures of inexpensive mixed oxides were stable under hydrothermal conditions, with modest calcium leaching (7.5%) and trace leaching of other metals. Using red clay or red mud resulted in >40% recovery of the energy in food waste as biocrude, greater than that obtained under noncatalytic conditions (18%) or from any individual constituent oxide (19–27%). The improved CHTL performance of the mixed metal oxides compared with single-metal oxides was attributed to the synergistic effects of base and acid sites present on catalyst surfaces; mixed oxides presented balanced densities of acids and bases, whereas the constituent oxides were either primarily acidic or primarily basic. Lastly, the percent of energy recovered as biocrude oil was strongly correlated with the base-to-acid site density ratio, providing an important performance predictor for CHTL conversion of food waste to bioenergy.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗