Search NASA⌕ Search

SEARCH · Search NASA

Results for “hygroscopic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Aerosol hygroscopicity over the South-East Atlantic Ocean during the biomass burning season – Part 2: Influence of sea salt and burning conditions on CCN hygroscopicity

Biomass burning (BB) significantly influences cloud condensation nuclei (CCN) concentrations over the southeastern Atlantic; however, aerosol hygroscopicity (κ) – a key factor for CCN activation – remains poorly constrained during the BB season. This study investigates κ variability using in situ measurements from Ascension Island during the 2016 and 2017 BB seasons. Results show substantial monthly variability, with κ values lowest in August and increasing through October. On average, κ was significantly higher in 2017 (∼ 0.55) than in 2016 (∼ 0.33), suggesting that the aerosols in 2017 were more hygroscopic and more easily activated as CCN. Sulfate and sea salt were the two dominant contributors to κ and the primary drivers of its interannual variability. During the 2017 BB season, sulfate – the major inorganic component – accounted for ∼ 34 % of the submicron aerosol mass, while sea salt, estimated via κ-closure analysis, contributed ∼ 17 %. The higher κ in 2017 was largely attributed to increased sea salt, likely driven by stronger marine winds. Approximately 67 % of sulfate was linked to BB emissions. Variations in BB combustion efficiency, modulated by regional meteorology, influenced sulfate fraction and thus κ values. Specifically, higher relative humidity and lower wind speeds over BB source regions in 2017 favored smoldering combustion, explaining the higher sulfate fraction. Overall, the observed interannual differences in aerosol hygroscopicity reflect the combined impacts of BB combustion characteristics and sea salt emissions, underscoring the critical roles of both BB and marine aerosol sources in regulating aerosol-cloud interactions over the southeastern Atlantic.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Evaluation and improvement of the parameterization of aerosol hygroscopicity in global climate models using in-situ surface measurements (Final Report)

Aerosols are tiny particles suspended on the atmosphere that can interact with incoming solar radiation and affect the Earth radiative budget. They do so by scattering and absorbing solar radiation, and these properties vary depending on the aerosol size and chemical composition. Moreover, by taking up water from the surrounding air, hygroscopic aerosol particles will grow in size and change their chemical composition, thus modifying their optical properties (scattering and absorption) and their final impact on radiative forcing calculations. An accurate knowledge of aerosol hygroscopicity is crucial for estimating the net radiative impact of aerosols. We took a three-pronged approach to improve our understanding of aerosol hygroscopicity and how it is implemented in Earth system models. In the first part of our project, we developed a benchmark dataset from existing aerosol hygroscopic growth measurements made by tandem nephelometer humidogram systems. We analyzed, using a standardized methodology, observations from 26 in-situ stations around the globe. Measurement data was collected from multiple data providers, reviewed and harmonized to create a consistent dataset of the scattering enhancement factor due to aerosol water uptake. This dataset is archived in several publicly available databases for use by interested researchers. In the second part of the project, we used the benchmark hygroscopicity dataset to perform a global study on aerosol hygroscopicity and aerosol optical properties. Measurements show a global picture of scattering enhancement with larger values for Arctic and marine sites and lower for urban and desert sites. We assessed the RH dependence of aerosol radiative forcing and showed that the overall effect of aerosol hygroscopicity on DARF is an increase in the absolute forcing effect (negative sign) by a factor of up to 4 compared to dry conditions (RH<40%). Finally, we explored using aerosol single scattering albedo (SSA) and scattering Angstrom exponent (SAE) as possible proxies for aerosol hygroscopicity. SSA showed more promise as a surrogate for the scattering enhancement factor than SAE, but neither was ideal. In the third part of the project we evaluated the output of ten Earth system models (ESMs) against the benchmark hygroscopicity dataset. ESMs utilize various schemes for aerosol hygroscopicity which had not been previously tested against observations on a global scale. We found that ESMs currently overestimate scattering enhancement due to hygroscopic growth. Model parameterizations of hygroscopicity and model chemistry are two main factors driving the observed diversity in hygroscopicity simulations among the models. In addition, our study makes several suggestions for modelers, including improving the parameterizations of organic and sea salt aerosol hygroscopicity. Future hygroscopicity model evaluation experiments should include the model data related to particles size which was not available for our study.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2006

Application of Aerosol Hygroscopicity Measured at the Atmospheric Radiation Measurement Program's Southern Great Plains Site to Examine Composition and Evolution

A Differential Mobility Analyzer/Tandem Differential Mobility Analyzer (DMA/TDMA) was used to measure submicron aerosol size distributions, hygroscopicity, and occasionally volatility during the May 2003 Aerosol Intensive Operational Period (IOP) at the Central Facility of the Atmospheric Radiation Measurement Program's Southern Great Plains (ARM SGP) site. Hygroscopic growth factor distributions for particles at eight dry diameters ranging from 0.012 micrometers to 0.600 micrometers were measured throughout the study. For a subset of particle sizes, more detailed measurements were occasionally made in which the relative humidity or temperature to which the aerosol was exposed was varied over a wide range. These measurements, in conjunction with backtrajectory clustering, were used to infer aerosol composition and to gain insight into the processes responsible for evolution. The hygroscopic growth of both the smallest and largest particles analyzed was typically less than that of particles with dry diameters of about 0.100 micrometers. It is speculated that condensation of secondary organic aerosol on nucleation mode particles is largely responsible for the minimal hygroscopic growth observed at the smallest sizes considered. Growth factor distributions of the largest particles characterized typically contained a nonhygroscopic mode believed to be composed primarily of dust. A model was developed to characterize the hygroscopic properties of particles within a size distribution mode through analysis of the fixed size hygroscopic growth measurements. The performance of this model was quantified through comparison of the measured fixed size hygroscopic growth factor distributions with those simulated through convolution of the size-resolved concentration contributed by each of the size modes and the mode-resolved hygroscopicity. This transformation from sizeresolved hygroscopicity to mode-resolved hygroscopicity facilitated examination of changes in the hygroscopic properties of particles within a size distribution mode that accompanied changes in the sizes of those particles. This model was used to examine three specific cases in which the sampled aerosol evolved slowly over a period of hours or days.

Gasparini, Roberto↗
DOE OSTI2024

Aerosol hygroscopicity over the southeast Atlantic Ocean during the biomass burning season – Part 1: From the perspective of scattering enhancement​​​​​​​

Aerosol hygroscopicity plays a vital role in aerosol radiative forcing. One key parameter describing hygroscopicity is the scattering enhancement factor, f(RH), defined as the ratio of the scattering coefficient at humidified relative humidity (RH) to its dry value. Here, we utilize the f(80 %) from ORACLES (ObseRvations of Aerosols above CLouds and their intEractionS) 2016 and 2018 airborne measurements to investigate the hygroscopicity of aerosols, its vertical distribution, its relationship with chemical composition, and its sensitivity to organic aerosol (OA) hygroscopicity over the southeast Atlantic (SEA) Ocean during the biomass burning (BB) season. We found that aerosol hygroscopicity remains steady above 2 km, with a mean f(80 %) of 1.40 ± 0.17. Below 2 km, aerosol hygroscopicity increases with decreasing altitude, with a mean f(80 %) of 1.51 ± 0.22, consistent with higher values of BB aerosol hygroscopicity found in the literature. The hygroscopicity parameter of OA (κ OA ) is retrieved from the Mie model with a mean value of 0.11 ± 0.08, which is in the middle to upper range compared to the literature. Higher OA hygroscopicity is related to aerosols that are more aged, oxidized, and present at lower altitudes. The enhanced biomass burning aerosol (BBA) hygroscopicity at lower altitudes is mainly due to a lower OA fraction, increased sulfate fraction, and greater κ OA at lower altitudes. We propose a parameterization that quantifies f(RH) with chemical composition and κOA based on Mie simulation of internally mixed OA–(NH 4 ) 2 SO 4 –BC mixtures. The good agreement between the predictions and the ORACLES measurements implies that the aerosols in the SEA during the BB season can be largely represented by the OA–(NH 4 ) 2 SO 4 –BC internal mixture with respect to the f(RH) prediction. The sensitivity of f(RH) to κ OA indicates that applying a constant κ OA is only suitable when the OA fraction is low and κ OA shows limited variation. However, in situations deviating these two criteria, κ OA can notably impact scattering coefficients and aerosol radiative effect; therefore, accounting for κ OA variability is recommended.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

A novel methodology for assessing the hygroscopicity of aerosol filter samples

Abstract. Due to US regulations, concentrations of hygroscopic inorganic sulfate and nitrate have declined in recent years, leading to an increased importance of the hygroscopic nature of organic matter (OM). The hygroscopicity of OM is poorly characterized because only a fraction of the multitude of organic compounds in the atmosphere is readily measured, and there is limited information on their hygroscopic behaviors. Hygroscopicity of aerosol is traditionally measured using a humidified tandem differential mobility analyzer (HTDMA) or electrodynamic balance (EDB). EDB measures water uptake by a single particle. For ambient and chamber studies, HTDMA measurements provide water uptake and particle size information but not chemical composition. To fill this information gap, we developed a novel methodology to assess the water uptake by particles collected on Teflon filters. This method uses the same filter sample for both hygroscopicity measurements and chemical characterization, thereby providing an opportunity to link the measured hygroscopicity with ambient particle composition. To test the method, hygroscopic measurements were conducted in the laboratory for ammonium sulfate, sodium chloride, glucose, and malonic acid, which were collected on 25 mm Teflon filters using an aerosol generator and sampler. Constant-humidity solutions (CHSs), including potassium chloride, barium chloride dihydrate, and potassium sulfate, were employed in a saturated form to maintain the relative humidity (RH) at approximately 84 %, 90 %, and 97 % in small chambers. Our preliminary experiments revealed that, without the pouch, water uptake measurements were not feasible due to rapid water loss during weighing. Additionally, we observed some absorption by the aluminum pouch itself. To account for this, concurrent measurements were conducted for both the loaded and the blank filters at each RH level. Thus, the dry loaded and blank Teflon filters were placed in aluminum pouches with one side open and in RH-controlled chambers for more than 24 h. The wet loaded samples and wet blanks were then weighed using an ultramicrobalance to determine the water uptake by the respective compound and the blank Teflon filter. The net amount of water absorbed by each compound was calculated by subtracting the water uptake of the blank filter from that of the wet loaded filter. Hygroscopic parameters, including the water-to-solute (W / S) ratio, molality, mass fraction solute (mfs), and growth factors (GFs), were calculated from the measurements. The results obtained are consistent with those reported by the Extended Aerosol Inorganics Model (E-AIM) and previous studies utilizing HTDMA and EDB for these compounds, highlighting the accuracy of this new methodology. This new approach enables the hygroscopicity and chemical composition of individual filter samples to be assessed so that in complex mixtures, such as chamber and ambient samples, the total water uptake can be parsed between the inorganic and organic components of the aerosol.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2019

Aerosol hygroscopic growth, contributing factors, and impact on haze events in a severely polluted region in northern China

This study investigates the impact of the aerosol hygroscopic growth effect on haze events in Xingtai, a heavily polluted city in the central part of the North China Plain (NCP), using a large array of instruments measuring aerosol optical, physical, and chemical properties. Key instruments used and measurements made include the Raman lidar for atmospheric water vapor content and aerosol optical profiles, the PC-3016A GrayWolf six-channel handheld particle and mass meter for atmospheric total particulate matter (PM) that has diameters less than 1 and 2.5 µ m (PM 1 and PM 2.5 , respectively), the aerosol chemical speciation monitor (ACSM) for chemical components in PM 1 , and the hygroscopic tandem differential mobility analyzer (H-TDMA) for aerosol hygroscopicity. The changes in PM 1 and PM 2.5 agreed well with that of the water vapor content due to the aerosol hygroscopic growth effect. Two cases were selected to further analyze the effects of aerosol hygroscopic growth on haze events. The lidar-estimated hygroscopic enhancement factor for the aerosol backscattering coefficient during a relatively clean period (Case I) was lower than that during a pollution event (Case II) with similar relative humidity (RH) levels of 80 %–91 %. The Kasten model was used to fit the aerosol optical hygroscopic growth factor (GF) whose parameter b differed considerably between the two cases, i.e., 0.1000 (Case I) versus 0.9346 (Case II). The aerosol acidity value calculated from ACSM data for Case I (1.35) was less than that for Case II (1.50) due to different amounts of inorganics such as NH 4 NO 3 , NH 4 HSO 4 , and (NH 4 ) 2 SO 4 . Model results based on H-TDMA data showed that aerosol hygroscopic growth factors in each size category (40, 80, 110, 150, and 200 nm) at different RH levels (80 %–91 %) for Case I were lower than those for Case II. For similar ambient RH levels, the high content of nitrate facilitates the hygroscopic growth of aerosols, which may be a major factor contributing to heavy haze episodes in Xingtai.

Chen, Jun↗
DOE OSTI2022

Evaluation of assumptions made by Hygroscopic Tandem Differential Mobility Analyzer inversion routines

The Hygroscopic Tandem Differential Mobility Analyzer (H-TDMA) measures the hygroscopicity of atmospheric particles, and many atmospheric processes that change this hygroscopicity also change the atmospheric size distribution. Two assumptions made during H-TDMA inversion create spurious hygroscopic trends as a function of the changing inlet size distribution. These two assumptions—that the particles exiting the first Differential Mobility Analyzer (DMA1) are singly charged and that the inlet size distribution has a slope of zero (flat)— generate Multi-Charge Dispersion (MCD) bias and Slope bias, respectively. First, we use a model, named TAO, to show that the inlet size distribution could theoretically change the measured ammonium sulfate hygroscopicity by 10%–20% as a function of diameter or experimental time with no change in relative humidity. Secondly, we show experimentally that aerosol emitted from the flaming combustion of grass creates MCD bias. Here, in this experiment, we measure the CPC response of the first three charges and invert these responses using a new routine named Junior. Junior's inversion of each charge shows that one growth factor distribution describes all measured diameters (no growth dependence on diameter). As in the modeling study above, previous publications of this aerosol system, using traditional inversion assumptions, report a decrease in hygroscopicity as DMA1 diameter increases. Unlike traditional inversions, Junior's inversion does not assume the particles are singly charged nor does it make the flat inlet size distribution assumption. Instead, both the inlet size distribution and each charge's CPC response are measured quantities. Thus, the discrepancy between our inversion results and previous publications is likely due to the traditional inversion routine assumptions. This underscores the importance for accounting for Slope and MCD bias during inversions. Experimental results should be carefully analyzed when reporting hygroscopic trends with respect to diameter or experimental time when using the traditional inversion assumptions.

42 ENGINEERING↗
DOE OSTI2026

Hygroscopic growth of UO 2 F 2 nanoparticles

Hygroscopicity is an important physicochemical property of aerosol that describes the ability of a particle to uptake water. The hygroscopic properties of uranyl fluoride (UO 2 F 2 ) aerosol generated from a UF 6 hydrolysis reactor was investigated for the first time using a custom-built Humidified Tandem Differential Mobility Analyzer (HTDMA). The HTDMA is capable of measuring UO 2 F 2 nanoparticle growth determined by mobility size over a wide range of atmospheric humidity from dry conditions at <10% relative humidity (RH) to 85% RH. The hygroscopic properties were determined for nanoparticles as small as 3.5 nm in this study. Although the largest size of UO 2 F 2 nanoparticles was 80 nm, monodisperse aerosol with a mobility diameter of up to approximately 500 nm can be investigated using the HTDMA. Anhydrous UO 2 F 2 nanoparticles with a mobility diameter of 3.5 nm were shown to be highly hygroscopic with a deliquescence relative humidity (DRH) of 10%. Hydrates with a larger mobility diameter from 10 to 80 nm were non-hygroscopic with no observable DRH and limited water uptake up to 85% RH. Here, these results demonstrate the hygroscopic properties of UO 2 F 2 nanoparticles are highly variable and based on both the mobility size and hydration state. Hygroscopicity affects the physicochemical properties of UO 2 F 2 nanoparticles, including the aerosol phase state and viscosity, with impacts on aerosol growth, coagulation, and deposition that is critical for understanding the fate and transport of UO 2 F 2 nanoparticles in the atmosphere.

Hygroscopicity↗
DOE OSTI2025

Hygroscopic Growth of UO 2 F 2 Particles

Hygroscopicity is an important physicochemical property of aerosol that describes the ability of a particle to uptake water. The hygroscopic properties of uranyl fluoride (UO 2 F 2 ) aerosol generated from a UF 6 hydrolysis reactor was investigated for the first time using a custom-built Humidified Tandem Differential Mobility Analyzer (HTDMA). The HTDMA is capable of measuring UO 2 F 2 particle growth determined by mobility size over a wide range of atmospheric humidity from dry conditions at <10% relative humidity (RH) to 85% RH. The hygroscopic properties were determined for nanoparticles as small as 3.5 nm in this study. Anhydrous UO 2 F 2 particles with a mobility diameter of 3.5 nm were shown to be highly hygroscopic with a deliquescence relative humidity (DRH) of 10%. Hydrates with a larger mobility diameter of 10 to 80 nm were non-hygroscopic with no observable DRH and limited water uptake up to 85% RH. These results demonstrate the hygroscopic properties of UO 2 F 2 particles are highly variable and based on both the mobility size and hydration state. Hygroscopicity affects the physicochemical properties of UO 2 F 2 particles, including the aerosol phase state and viscosity, with impacts on aerosol growth, coagulation, and deposition that is critical for understanding the fate and transport of UO 2 F 2 particles in the atmosphere.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Rapid measurement of RH-dependent aerosol hygroscopic growth using a humidity-controlled fast integrated mobility spectrometer (HFIMS)

Abstract. The ability of aerosol particles to uptake water (hygroscopic growth) is an important determinant of aerosol optical properties and radiative effects. Aerosol hygroscopic growth is traditionally measured by humidified tandem differential mobility analyzers (HTDMA), in which size-selected dry particles are exposed to elevated relative humidity (RH), and the size distribution of humidified particles is subsequently measured using a scanning mobility particle sizer. As a scanning mobility particle sizer can measure only one particle size at a time, HTDMA measurements are time consuming, and ambient measurements are often limited to a single RH level. Pinterich et al. (2017b) showed that fast measurements of aerosol hygroscopic growth are possible using a humidity-controlled fast integrated mobility spectrometer (HFIMS). In HFIMS, the size distribution of humidified particles is rapidly captured by a water-based fast integrated mobility spectrometer (WFIMS), leading to a factor of ∼10 increase in measurement time resolution. In this study we present a prototype HFIMS that extends fast hygroscopic growth measurements to a wide range of atmospherically relevant RH values, allowing for more comprehensive characterizations of aerosol hygroscopic growth. A dual-channel humidifier consisting of two humidity conditioners in parallel is employed such that aerosol RH can be quickly stepped among different RH levels by sampling from alternating conditioners. The measurement sequence is also optimized to minimize the transition time between different particle sizes. The HFIMS is capable of measuring aerosol hygroscopic growth of six particle diameters under five RH levels ranging from 20 % to 85 % (30 separate measurements) every 25 min. The performance of this HFIMS is characterized and validated using laboratory-generated ammonium sulfate aerosol standards. Measurements of ambient aerosols are shown to demonstrate the capability of HFIMS to capture the rapid evolution of aerosol hygroscopic growth and its dependence on both size and RH.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Investigating Aerosol Hygroscopicity in the Subcloud Transition Zone and at the Surface in the Southern Great Plains

Aerosols beneath a cloud base, a subcloud transition zone (SCTZ), are key to understand both the aerosol-cloud interaction and aerosol-radiation interactions. Lidars have been the primary means of observing aerosols in the SCTZ by virtue of enhanced light scattered by aerosol particles. The enhanced light maybe caused by several factors: the aerosol swelling effect due to hygroscopicity under high relative humidity, cloud 3-dimensional (3D) effect, aerosol nucleation into cloud droplets, etc. While each factor and process has been known, their relative contributions are much poorly quantified. This study explores the hygroscopicity and optical properties of aerosols in the SCTZ and at ground level in the Southern Great Plains (SGP) region. Utilizing comprehensive observational data from the U.S. Department of Energy's Atmospheric Radiation Measurement at the Oklahoma SGP site, including ground-based aerosol measurements and Raman lidar profiles from April 2021 to April 2022, this study extensively analyzes the influence of aerosol hygroscopic growth and cloud fragments on aerosol optical properties. Distinct seasonal variations in aerosol hygroscopic characteristics are revealed. At the ground level, aerosols in autumn and winter exhibit stronger hygroscopicity due to a higher proportion of inorganic content than summer. In the SCTZ, aerosols during summer show enhanced backscatter due to strong cloud fragmentation effects, with numerous cloud fragments elevating hygroscopicity beyond that observed in autumn and winter. These insights are crucial for understanding the interactions between aerosols at the surface and cloud layers, evaluating cloud condensation nuclei beneath clouds, and their implications for atmospheric radiation and climate modeling.

Hu, Rong [Beijing Normal University, Beijing (Chin↗
DOE OSTI2022

Wastewater Recycling Using a Hygroscopic Cooling System

This project by the Energy & Environmental Research Center (EERC), Baltimore Aircoil Company (BAC), and Great River Energy (GRE) evaluated the concept of recycling wastewater at a coal-fired power plant using a hygroscopic cooling system, which is an evaporative cooling technology analogous to conventional cooling towers, except that sparingly soluble dissolved solids are precipitated and removed as waste solids instead of purging them with a liquid blowdown stream. This technology can maximize the use of plant makeup water by obtaining useful evaporative cooling from wastewater while minimizing the volume of wastes needing disposal. Experimental activities were conducted in two phases, a laboratory-based evaluation of the properties of wastewater from the host site, GRE’s Coal Creek Station near Underwood, North Dakota, and a field test of a small pilot hygroscopic cooling system at the host site power plant. Findings from the laboratory study informed the design of the pilot system and the system’s field test performance served as the basis for a techno-economic analysis (TEA) of the hygroscopic recycling concept. At the preferred operating conditions identified during the TEA, the wet-bulb approach temperature of the tower was 7.3°C (13°F) and the volume of blowdown produced by the plant was reduced to 5.4% of its incoming volume. Waste solids produced during field testing were classified as nonhazardous waste based on the measured hazardous element content and evaluation of their leaching potential. However, to qualify as a solid for landfill disposal i.e., as determined by the U.S. Environmental Protection Agency’s paint filter test, it appears that a dewatering step beyond hydrocyclone separation is needed. The baseline levelized cost of wastewater disposal (LCWD) for hygroscopic wastewater recycling was estimated to be $\$ $3.69–$\$ $3.72 per m3 of plant blowdown. Capital cost was estimated to contribute over 54% to the LCWD, and parameters that impact capital cost such as the heat exchange coil material of construction and the tower’s wet-bulb approach temperature were identified as having the greatest impact on overall LCWD. A LCWD estimate prepared for the same application but using thermomechanical brine evaporation was almost 40% higher than that calculated for hygroscopic cooling, despite recovering distilled-quality water for reuse, while the LCWD for disposal-only, deep well injection was estimated to be 30% lower compared to hygroscopic wastewater recycling.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2023

Maximizing Uptake of Hygroscopic Hydrogels Through Extreme Swelling-Induced Salt Loading

Hygroscopic hydrogels have emerged as scalable and low-cost materials with the potential of high-performance vapor sorption for atmospheric water harvesting, dehumidification, and passive cooling. Despite extensive research interest aimed at improving hygroscopic hydrogels, devices using these materials still exhibit insufficient performance, partly due to limited water uptake of the hydrogels. In this work, we study the swelling dynamics of hydrogels in aqueous lithium chloride solutions and use this to achieve extreme salt loading of hygroscopic hydrogels. By rationally tuning the salt concentration used for swelling we achieve successful synthesis of hygroscopic hydrogels with high water uptake of 1.76 g/g, 2.53 g/g, 3.80 g/g at relative humidites of 30%, 50%, and 70%, respectively, exceeding previous hydrogels by over 19%. These water uptakes bring the performance of hydrogels within ≈91% of the fundamental limit of commonly used hygroscopic salts, while still avoiding leakage problems common in salt solutions. Furthermore, we elucidate via models the maximum uptake achievable without leakage as a function of the operating relative humidity and hydrogel swelling ratio. The insights from this work can be used to design hygroscopic hydrogels with exceptional performance for a wide variety of sorption applications to tackle global challenges such as water scarcity and energy efficiency.

25 ENERGY STORAGE↗
DOE OSTI2023

Aerosol Hygroscopic Growth, Mixing State, and Cloud Condensation Nuclei Activity during TRACER (Field Campaign Report)

Convective clouds play a critical role in the Earth’s climate system. Recent research has shown that a realistic representation of convective processes is critical to constraining climate sensitivity in global climate models. Theoretical and modeling studies showed that aerosols could have strong dynamic feedback to convection in warm and humid environments through enhancing ice-related processes and condensational growth. A few observation-based studies also suggested the influence of aerosols on convective cloud and precipitation properties. However, robust observational quantification of an aerosol effect on convective clouds isolated from other factors remains elusive. Understanding the impact of aerosol on convective clouds requires knowledge of the cloud condensation nuclei (CCN) spectrum, which represents the number of particles that uptake water and form cloud droplets as a function of supersaturation. The water uptake by aerosol is also of critical importance for the direct interaction of aerosol with radiation (i.e., aerosol direct effect) due to light scattering and absorption by aerosol. While both droplet activation under supersaturated conditions (i.e., relative humidity RH > 100%) and the hygroscopic growth under sub-saturated conditions (i.e., RH < 100%) are strongly influenced by particle hygroscopicity, the thermodynamic regimes and measurement methods are quite different. Aerosol particles, especially organic particles, can exhibit higher hygroscopicity for droplet activation than that for hygroscopic growth. In the subsaturated regime, the hygroscopicity of organic particles can also vary strongly with RH. However, global climate models usually treat organic species in aerosols with a constant hygroscopicity, potentially introducing substantial uncertainties in the quantification of aerosol radiative effects.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Heat dissipation systems with hygroscopic working fluid

In various embodiments, the present invention relates to heat dissipation systems including a hygroscopic working fluid and methods of using the same. In various embodiments, the present invention provides a method for heat dissipation using a hygroscopic working fluid. The method can include transferring thermal energy from a heated process fluid to the hygroscopic working fluid in a process heat exchanger, to form a cooled process fluid. The method can include condensing liquid from a feed gas on a heat transfer surface of a feed gas heat exchanger in contact with the cooled process fluid, to form a cooled feed gas, the heated process fluid, and a condensate. The method can include dissipating thermal energy from the hygroscopic working fluid to a cooling gas composition with a fluid-air contactor. The method can include transferring moisture between the hygroscopic working fluid and the cooling gas composition with the fluid-air contactor. The method can include adding at least part of the condensate to the hygroscopic working fluid.

Martin, Christopher Lee↗
DOE OSTI2022

Heat and mass transfer in hygroscopic hydrogels

Sorption and desorption with hygroscopic hydrogels hold significant promise for thermal management, passive cooling, thermal energy storage, and atmospheric water harvesting. However, a comprehensive understanding of the energy and mass transport mechanisms in hygroscopic hydrogels remains missing, impeding accurate modeling and optimization. In this paper, we develop a model for the simultaneous vapor, water, and heat transfer in hygroscopic hydrogels during sorption and desorption processes. We show that by considering vapor diffusion in the hydrogel micropores, water diffusion in the polymer mesh, and heat transfer in the porous hydrogel, we can accurately capture experimentally observed thermally-driven desorption rates in these hydrogels. Furthermore, we consider three typical operating configurations of hydrogels and elucidate the differences in the transport mechanisms depending on the configuration. Finally, for each of these configurations, we identify key design parameters, including hydrogel thickness, hydrogel shear modulus, heat transfer coefficient, and thermal conductivity, and we parametrically show that by varying these parameters, a hygroscopic hydrogel can desorb up to 128.5%, 14.9%, 69.7%, and 9.6% more water, respectively, relative to the initial water content. This work provides a generic framework to model sorption and desorption processes in hygroscopic hydrogels which can guide the design and optimization in applications of thermal management, passive cooling, thermal energy storage, and atmospheric water harvesting with hydrogels.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Cloud Condensation Nuclei Hygroscopicity Value-Added Product Report

The purpose of the Atmospheric Radiation Measurement (ARM) user facility’s cloud condensation nuclei hygroscopicity parameter (AOSCCNSMPSKAPPA) value-added product (VAP) is to calculate the hygroscopicity parameter, kappa, to quantify the ability of aerosols to activate into cloud water droplets. The hygroscopicity parameter is often used to model the cloud condensation nuclei (CCN) activity of atmospheric aerosols of different sizes and compositions, providing additional insight on the influence of aerosols on climate. Laboratory experiments show that the kappa values for highly hygroscopic aerosols, such as salts and sulfates, vary from 0.5 to 1.4 (Petters and Kreidenweis 2007). For organic compounds they are observed to vary between 0.01 and 0.5. For non-hygroscopic aerosols, such as soot, kappa values are very close to zero. Ambient aerosols are complex mixtures of organic and inorganic compounds and previous observations indicate that kappa values typically vary from 0.05 to 0.9 (Petters and Kreidenweis 2007).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Cloud Condensation Nuclei Hygroscopicity Value-Added Product Report

The purpose of the U.S. Department of Energy Atmospheric Radiation Measurement (ARM) user facility’s Cloud Condensation Nuclei Hygroscopicity Parameter (AOSCCNSMPSKAPPA and AOSCCNUHSASKAPPA) Value-Added Product (VAP) is to calculate the hygroscopicity parameter, kappa, to quantify the ability of aerosols to activate into cloud water droplets. The hygroscopicity parameter is often used to model the cloud condensation nuclei (CCN) activity of atmospheric aerosols of different sizes and compositions, providing additional insight on the influence of aerosols on climate. The AOSCCNUHSASKAPPA VAP was recently developed to provides kappa data for ARM sites where AOSCCNSMPSKAPPA was missing. Laboratory experiments show that the kappa values for highly hygroscopic aerosols vary from 0.5 to 1.4 (Petters and Kreidenweis 2007). For organic compounds they are observed to vary between 0.01 and 0.5. For non-hygroscopic aerosols, such as soot, kappa values are very close to zero. Ambient aerosols are complex mixtures of organic and inorganic compounds and previous observations indicate that kappa values for these aerosols typically vary from 0.05 to 0.9 (Petters and Kreidenweis 2007).

54 ENVIRONMENTAL SCIENCES↗