Far infrared luminescence
Far infrared luminescence from solids illuminated by visible light
Stoddard, A. E.↗
SEARCH · Search NASA
Results for “infrared luminescence”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Heterovalent Substitution of K 2 SrP 2 O 7 :Cr 3+ to Achieve Anti-Thermal-Quenching Broadband Near-Infrared Luminescence
Broadband near-infrared (NIR) light sources based on phosphor-converted light-emitting diodes are highly desirable for biochemical analysis and medical diagnosis applications. However, thermal quenching remains a demanding challenge for developing efficient NIR phosphors. Herein, we report the enhancement of both quantum efficiency and thermal stability in Cr 3+ -activated K 2 SrP 2 O 7 phosphors through a heterovalent substitution strategy by replacing Sr 2+ with Al 3+ in K 2 Sr 1–x Al x P 2 O 7 (0.05 ≤ x ≤ 0.2) to obtain optimized broadband NIR emission. Structural modulation via Al 3+ substitution leads to the optimized composition, K 2 Sr 0.88 Al 0.1 P 2 O 7 :0.02Cr 3+ , which emits across a broad NIR range of 650–1100 nm peaking at 807 nm with a full width at half-maximum of ∼130 nm under 448 nm excitation. Remarkably, its emission intensity at 150 °C remains 120% of the initial value at room temperature, demonstrating a rare antithermal-quenching behavior. Temperature-dependent XRD studies further reveal that Al 3+ substitution effectively suppresses lattice expansion at elevated temperatures, indicating enhanced lattice stability under thermal excitation. Detailed structural and spectral analyses show that the substitution enhances local site symmetry, reduces electron–phonon coupling, increases thermally induced absorption probability, and fortifies energetic barriers against nonradiative transitions. These synergistic effects collectively endow this NIR phosphor with a superior thermal stability. Furthermore, NIR light-emitting diodes fabricated with this phosphor exhibit strong potential for applications in information identification, nondestructive detection, and night vision technologies. This study demonstrates a local structure engineering strategy for designing thermally robust Cr 3+ -activated NIR phosphors, offering valuable insights into material discovery and NIR spectroscopy device development.
Cr3+↗
Near Infrared Luminescence Properties of Mn(5+): Ca5(PO4)3F
We report a spectroscopic investigation of Mn(5+) doped Ca5(PO4)(sub 3)F or FAP. Mn(5+) doped crystals have recently attracted world wide attention for potential solid-state laser applications. Following optical excitation of Mn: FAP with the 600 nm output of a Nd: YAG OPO laser system, we observed a strong near infrared luminescence centered at around 1150 nm. The room temperature luminescence decay time was measured to be approximately 635 microseconds. We attribute the infrared luminescence to the(1)E yields (3)A2 transition of tetrahedrally coordinated Mn5+ ions located in a strong crystal field environment. Absorption, luminescence and lifetime data of Mn: FAP will be presented and discussed.
Davis, Valetta R.↗
Detecting Thermal Barrier Coating Delamination Using Visible and Near-Infrared Luminescence from Erbium-Doped Sublayers
Nondestructive diagnostic tools are needed to monitor early stages of delamination progression in thermal barrier coatings (TBCs) because the risk of delamination induced coating failure will compromise engine performance and safety. Previous work has demonstrated that for TBCs composed of yttria-stabilized zirconia (YSZ), luminescence from a buried europium-doped sublayer can be utilized to identify the location of TBC delamination from the substantially higher luminescence intensity observed from the delaminated regions of the TBC. Luminescence measurements from buried europium-doped layers depend on sufficient transmittance of the 532 nm excitation and 606 nm emission wavelengths through the attenuating undoped YSZ overlayer to produce easily detected luminescence. In the present work, improved delamination indication is demonstrated using erbium-doped YSZ sublayers. For visible-wavelength luminescence, the erbium-doped sublayer offers the advantage of a very strong excitation peak at 517 nm that can be conveniently excited a 514 nm Ar ion laser. More importantly, the erbium-doped sublayer also produces near-infrared luminescence at 1550 nm that is effectively excited by a 980 nm laser diode. Both the 980 nm excitation and the 1550 nm emission are transmitted through the TBC with much less attenuation than visible wavelengths and therefore show great promise for delamination monitoring through thicker or more highly scattering TBCs. The application of this approach for both electron beam physical vapor deposited (EB-PVD) and plasma-sprayed TBCs is discussed.
Eldridge, J. I.↗
Molecular Origins of Near-Infrared Luminescence in Molybdenum and Tungsten Oxyhalide Perovskites
Materials with near-infrared (near-IR) luminescence are desirable for applications in communications and sensing, as well as biomedical diagnostics and imaging. The most used inorganic near-IR emitters rely on precise doping of host crystal structures with select rare-earth or transition metal ions. Recently, another class of materials with intrinsic near-IR emission has been reported. The compositions of these materials were initially described as vacancy-ordered halide double perovskites Cs 2 MoCl 6 and Cs 2 WCl 6 , but further investigation by some of us on the compound reported as Cs2WCl6 revealed an oxyhalide instead, with a composition Cs 2 WO x Cl 6–x , where 1 < x < 2. Here we demonstrate that the Mo compounds similarly possess the composition Cs 2 MoO x Cl 6–x or Cs 2 MoO x Br 6–x where 1 < x < 2. Preparing the pure halide appears harder for Mo than for W, and we have not succeeded in doing so. The distinctly different composition requires the coordination environment and oxidation state for the Mo and W centers to be reconsidered from what was assumed for the pure halides. In this work, we examine the mechanism for near-IR emission in these materials given their true structures and compositions. We demonstrate that the luminescence is due to the specific d-orbital splitting caused by the presence of oxygen in the distorted [MOX 5 ] 2– octahedra (X is Cl or Br). The fine structure in the emission spectra at low temperatures has been resolved and is attributed to vibronic coupling to the Mo–O and W–O bond stretches. Understanding the true structure and composition of these interesting materials, besides explaining the near-IR luminescence, suggests how this desirable emission can be realized and manipulated.
36 MATERIALS SCIENCE↗
Source of Bright Near-Infrared Luminescence in Gold Nanoclusters
Gold nanoclusters with near-infrared (NIR) photoluminescence (PL) have great potential as sensing and imaging materials in biomedical and bioimaging applications. In this work, Au 21 (S-Adm) 15 and Au 38 S 2 (S-Adm) 20 are used to unravel the underlying mechanisms for the improved quantum yields (QY), large Stokes shifts and long PL lifetimes in gold nanoclusters. Both nanoclusters show decent PL QY. In particular, the Au 38 S 2 (S-Adm) 20 nanocluster shows a bright NIR PL at 900 nm with QY up to 15% in normal solvents (such as toluene) at ambient conditions. The relatively lower QY for Au 21 (S-Adm) 15 (4%) compared to Au 38 S 2 (S-Adm) 20 is attributed to the lowest-lying excited state being symmetry-disallowed, as evidenced by the pressure-dependent anti-spectral shift of the absorption spectra compared to PL. Yet, Au 21 (S-Adm) 15 maintains some emissive properties due to a nearby symmetry-allowed excited state. Furthermore, our results show that suppression of non-radiative decay due to the surface “lock rings” which encircle the Au kernel and the surface “lock atoms” which bridge the fundamental Au-kernel units (e.g., tetrahedra, icosahedra, etc.) is the key to obtain high QYs in gold nanoclusters. Here, the complicated excited-state processes and the small absorption coefficient of the band-edge transition lead to the large Stokes shifts and the long PL lifetimes that are widely observed in gold nanoclusters.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Shaping the Infrared luminescence of Colloidal Nanocrystals Using a Dielectric Microcavity
As they have gained maturity, colloidal nanocrystals (NCs) have also expand the spectral range over of which they could be used for photonic and optoelectronic applications. In particular, the infrared use of NCs has become of utmost interest to develop cost-effective alternatives to current technologies. It is then critical not to let the material dictate the light–matter interaction, which is why the coupling of NCs to photonic cavities has been proposed. For infrared NCs, this approach has first been devoted to the control of absorption with in mind the increase of the signal magnitude for detectors. A Lot of efforts have been focused on the use of metallic metasurfaces. However, these generate significant optical losses and yield low quality factor. Here, this study rather focus on the coupling of infrared NCs to a dielectric mirror cavity. HgTe/CdS core-shell NCs are used and integrated into a cavity made of aperiodic dielectric mirrors. The effect of the substrate is systematically study on spectral linewidth, carrier dynamic, and emission directivity. The cavity is shown to narrow the PL by a factor 10, while focusing the emission over a 12° angle. Monitoring the power dependence of the emission, this study shows that the cavity leads to 250 K increase in the effective electronic temperature.
36 MATERIALS SCIENCE↗
Mid-infrared luminescence properties of erbium and dysprosium doped lanthanum titanate glasses
Glasses of composition x RE 2 O 3 -(17− x ) La 2 O 3 -83 TiO 2 were prepared by levitation melting from x = 0.1 to 9 for RE=Er and at x =0.1 and 1 for RE=Dy. The glasses have high transition temperature, exhibit low OH, and 1 mm thick discs are transparent out to 6 μ m. Mid-infrared emission lineshapes and lifetimes are comparable to what is seen in tellurite glasses containing Er 3+ and Dy 3+ . For x fixed at 1, the Er 3+ : 4 I 11/2 → 4 I 13/2 transition at 2716 nm has a fluorescence lifetime of 254 μ s and the Dy 3+ : 6 H 13/2 → 6 H 15/2 transition at 2957 nm has a fluorescence lifetime of 9.09 μ s. The results indicate that doped lanthanum titanate glasses offer the thermal stability of a ’hard’ glass with the host properties typically associated with ’soft’ glasses. Problems with the measurement of spectral features in the mid-infrared that could erroneously be assigned as resulting from rare-earth ion emissions are presented and discussed.
36 MATERIALS SCIENCE↗
The Preparation Conditions of Chromium Doped ZnSe and Their Effect on The Infrared Luminescence Properties
We report the investigation by photoluminescence lifetime measurements of the near-IR emissions from a series of chromium-doped ZnSe samples, correlated to their preparation conditions. The samples were polycrystalline or single crystals prepared by post growth diffusion doping or single crystals doped during growth by the Physical Vapor Transport method. Room temperature lifetime values between 6 and 8 microseconds were measured for samples with Cr (2+) concentrations from low 10 (exp 17) to high 10 (exp 18) per cubic centimeter range. Lifetime data taken down to 78 K was found to be rather temperature independent, reconfirming previous reports indicating a quantum yield of the corresponding emission of close to 100% at room temperature. A strong decrease in the room temperature lifetime was found for chromium concentrations higher than 10 (exp 19) per cubic centimeter.
Burger, A.↗
The Preparation Conditions of Chromium Doped ZnSe and Their Effect on the Infrared Luminescence Properties
We report the investigation by photoluminescence lifetime measurements of the near-IR emissions from a series of chromium-doped ZnSe samples, correlated to their preparation conditions. The samples were polycrystalline or single crystals prepared by post growth diffusion doping or single crystals doped during growth by the physical vapor transport method. Room temperature lifetime values between 6 and 8 micro seconds were measured for samples with Cr2+ from low 10(exp 17) to high 10(exp 18) / cubic cm range. Lifetime data taken down to 78 K was found to be rather temperature independent, reconfirming previous reports indicating a quantum yield of the corresponding emission of close to 100% at room temperature. A strong decrease in the room temperature lifetime was found for chromium concentrations higher than 10(exp 19) / cubic CM.
Burger, A.↗
Stimulated Mid-Infrared Luminescence Experiment: Contribution to the Study of Pre-Earthquake Phenomena and UV Absorption by Interstellar Dust
The work performed under this proposal is based on the experimentally supported observation - or inference - that a small fraction of the oxygen anions in silicate minerals in igneous and high-grade metamorphic rocks on Earth may not be in the usual 2- oxidation state, O(sup 2-), but in a higher oxidation state, as O(sup -). If this is true, the same would likely apply to the fine dust that fills the diffuse interstellar medium. An (sup -) in a matrix of O(sup 2-) represents a defect electron in the valence band, also known as positive hole or p-hole for short. When two O(sup -) combine, they undergo spin-pairing and form a positive hole pair, PHP. Chemically speaking a PHP is a peroxy bond. In an oxide matrix a peroxy bond takes the form of a peroxy anion, O2(sup 2-). In a silicate matrix it probably exists in the form of peroxy links between adjacent [SiO4] tetrahedral, O3Si00\SiO3. From a physics perspective a PHP is an electrically inactive point defect, which contains dormant electronic charge carriers. When the peroxy bond breaks, p-hole charge carriers are released. These p-holes are diffusively mobile and spread through the O 2p-dominated valence band of the otherwise insulating mineral matrix.
Freund, Friedemann↗
Morphology and Luminescence Properties of Transition Metal Doped Zinc Selenide Crystals
Zinc selenide is an excellent matrix material to dope with rare-earth and transition metal to achieve mid-infrared luminescence to develop high power lasers. The luminescence, morphology and refractive index is significantly affected by the doping and defects generated due to size and valency of dopants, concentration, growth process and convection during the growth. The aim of the study is to investigate effect of point and line defects generated due to low doping of iron and chromium on the emission and morphology of the zinc selenide. Luminescence and morphological properties of large iron and chromium doped zinc selenide single crystals were studied to evaluate the effect of extremely low residual impurities and defects associated with the doping process. The emission properties following both short wavelength (i.e., ultraviolet; 350 – 370 nm) excitation and longer wavelength (i.e., near infrared; 850 – 870 nm) excitation were characterized. Luminescence emission bands were identified in both doped crystals. In addition to the primary emission bands, satellite peaks and intra-center transitions were also observed. Due to local population defects associated with the residual impurities (ppm to ppb) in the Fe-ZnSe and Cr-ZnSe crystals, peak emission wavelengths were observed to shift. Raman studies using 266 and 532 – nm excitation revealed different positions of longitudinal and transverse peaks for Fe-ZnSe and Cr-ZnSe crystals, associated with different levels of defects due to the different ion sizes. The emission bands were found to decrease in intensity due to recombination of residual impurity co-dopants and complex defects generated during growth and fabrication. Cryogenic temperature analyses revealed a very clean emission band due to freezing of some of the point and line defects. An emission band observed at 980 nm for both crystals at room temperature as well as cryogenic temperatures indicates a vibronic peak in ZnSe. The scanning electron microscopy (SEM) images of the local morphology support the conclusion that small crystallites in doped crystals are also present.
Zinc selenide↗
Optical Diagnostics for High-Temperature Thermal Barrier Coatings
Thermal barrier coatings (TBCs) are typically composed of translucent ceramic oxides that provide thermal protection for metallic components exposed to high-temperature environments, such as in jet turbine engines. Taking advantage of the translucent nature of TBCs, optical diagnostics have been developed that can provide an informed assessment of TBC health that will allow mitigating action to be taken before TBC degradation threatens performance or safety. In particular, rare-earth-doped luminescent sublayers have been integrated into the TBC structure to produce luminescence that monitors TBC erosion, delamination, and temperature gradients. Erosion monitoring of TBC-coated specimens is demonstrated by utilizing visible luminescence that is excited from a sublayer that is exposed by erosion. TBC delamination monitoring is achieved in TBCs with a base rare-earth-doped luminescent sublayer by the reflectance-enhanced increase in luminescence produced in regions containing buried delamination cracks. TBC temperature monitoring is demonstrated using the temperature-dependent decay time for luminescence originating from the specific coating depth associated with a rare-earth-doped luminescent sublayer. The design and implementation of these TBCs with integrated luminescent sublayers is discussed, including co-doping strategies to produce more penetrating near-infrared luminescence. It is demonstrated that integration of the rare-earth-doped sublayers is achieved with no reduction in TBC life. In addition, results for multilayer TBCs designed to also perform as radiation barriers are also presented.
Eldridge, Jeffrey I.↗
Cross-section of electrical impact excitation in bulk n-type monocrystalline Al:Cr:ZnSe
Middle-infrared luminescence of bulk Al:Cr:ZnSe crystal under direct electrical excitation of Cr 2+ , 5 E− 5 T 2 transition, is reported. Effective cross-section of electrical excitation was estimated based on comparative luminescence measurements under electrical and optical (1560 nm) excitations. Calculation of the threshold current density for lasing under electrical excitation of this material was also performed.
36 MATERIALS SCIENCE↗
Infrared optically stimulated luminescence of rare earth doped CaF 2 and co-doped with Al or Li produced by combustion synthesis
The aim of this paper is to characterize the IRSL response of rare earth doped CaF 2 and co-doped with Al or Li, produced by the solution combustion synthesis (SCS). The results showed a high intensity of the infrared optically stimulated luminescence (IRSL) response for the samples of CaF 2 doped with Tb and co-doped with Li. For the samples of CaF 2 doped with Ce and co-doped with Li present better IRSL response than the samples co-doped with Al. It was also observed that the samples of CaF 2 :Ce,Li present a high fading with 50% reduction of the IRSL signal in a period of 60 min. In case of the CaF 2 :Tb,Li there is no significant fading during this period. For clinical dosimetry the fast fading of the dosimeter is not adequate. However, this feature can be exploited for other applications such as tamper-proof passive systems that detect and timestamp the movement of undeclared nuclear materials, by the estimation of the OSL response of materials with different fading rates.
73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
Monitoring Delamination of Thermal Barrier Coatings by Near-Infrared and Upconversion Luminescence Imaging
Previous work has demonstrated that TBC delamination can be monitored by incorporating a thin luminescent sublayer that produces greatly increased luminescence intensity from delaminated regions of the TBC. Initial efforts utilized visible-wavelength luminescence from either europium or erbium doped sublayers. This approach exhibited good sensitivity to delamination of electron-beam physical-vapor-deposited (EB-PVD) TBCs, but limited sensitivity to delamination of the more highly scattering plasma-sprayed TBCs due to stronger optical scattering and to interference by luminescence from rare-earth impurities. These difficulties have now been overcome by new strategies employing near-infrared (NIR) and upconversion luminescence imaging. NIR luminescence at 1550 nm was produced in an erbium plus ytterbium co-doped yttria-stabilized zirconia (YSZ) luminescent sublayer using 980-nm excitation. Compared to visible-wavelength luminescence, these NIR emission and excitation wavelengths are much more weakly scattered by the TBC and therefore show much improved depth-probing capabilities. In addition, two-photon upconversion luminescence excitation at 980 nm wavelength produces luminescence emission at 562 nm with near-zero fluorescence background and exceptional contrast for delamination indication. The ability to detect TBC delamination produced by Rockwell indentation and by furnace cycling is demonstrated for both EB-PVD and plasma-sprayed TBCs. The relative strengths of the NIR and upconversion luminescence methods for monitoring TBC delamination are discussed.
Eldridge, J. I.↗
Enhancing the Infrared Emission from Silver Chalcogenide Quantum Dots Through Microcavity Coupling
Nanocrystals (NCs) appear as a promising platform for cost effective infrared optoelectronics, while offering a simplified coupling to the CMOS platform. However, this perspective is slowed down by toxicity concerns, the most effective materials being based on Pb and Hg. There is currently a large effort to bring forth new platforms that are active in the infrared with a reduced heavy metal content. Here, in this study, the focus is on silver chalcogenides, which, thanks to a combination of inter‐ and intraband transitions, is suited to cover both short and mid wave infrared ranges. However, this material being less mature, the achieved photoluminescence (PL) appears quite broad, which is problematic for device integration. Here, it is demonstrated that a strong control over the PL spectrum can be obtained through integration into a dielectric cavity that magnifies the electric field by a factor 20 and narrows the PL full width at half maximum down to 15 nm for an emission at telecom wavelength. The PL is also highly directional to avoid most waveguiding effects which is of utmost interest for enhancing the efficiency of NC‐based light emitting diodes.
infrared luminescence↗
Rigid cationic ligands enable high-efficiency NIR-II photoluminescence in copper( i ) iodide hybrid semiconductors
Near-infrared (NIR) luminescent materials are pivotal for advanced optoelectronic and biomedical applications, yet attaining efficient emission in the NIR-II region (950-1400 nm) remains challenging. Here, we introduce a ligand cationization strategy for designing copper(i) iodide-organic hybrid materials that emit in the NIR-II region (920-1120 nm) with PLQYs up to 8.58%. By incorporating rigid cationic ligands with CuI modules, we synergistically achieve bandgap narrowing (to 1.51 eV) and structural rigidification via ionic-dative bonding, effectively suppressing non-radiative decay while extending emission beyond 1100 nm. Coupled with solution processability-enabled by the successful synthesis of nanometer-sized nanoparticles in various shapes-and excellent thermal stability (≥210 °C), this work establishes ligand cationization as a universal approach for designing efficient NIR-II emitters.
Chen, Jingwen↗