SEARCH · Search NASA
Results for “inkjet printing”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Inkjet-printed SnO x as an effective electron transport layer for planar perovskite solar cells and the effect of Cu doping
Inkjet printing is a more sustainable and scalable fabrication method than spin coating for producing perovskite solar cells (PSCs). Although spin-coated SnO 2 has been intensively studied as an effective electron transport layer (ETL) for PSCs, inkjet-printed SnO 2 ETLs have not been widely reported. Here, we fabricated inkjet-printed, solution-processed SnO x ETLs for planar PSCs. A champion efficiency of 17.55% was achieved for the cell using a low-temperature processed SnO x ETL. The low-temperature SnO x exhibited an amorphous structure and outperformed high-temperature crystalline SnO 2 . The improved performance was attributed to enhanced charge extraction and transport and suppressed charge recombination at ETL/perovskite interfaces, which originated from enhanced electrical and optical properties of SnO x , improved perovskite film quality, and well-matched energy level alignment between the SnO x ETL and the perovskite layer. Furthermore, SnO x was doped with Cu. Cu doping increased surface oxygen defects and upshifted energy levels of SnO x , leading to reduced device performance. A tunable hysteresis was observed for PSCs with Cu-doped SnO x ETLs, decreasing at first and turning into inverted hysteresis afterwards with increasing Cu doping level. This tunable hysteresis was related to the interplay between charge/ion accumulation and recombination at ETL/perovskite interfaces in the case of electron extraction barriers.
Fully Inkjet‐Printed, 2D Materials‐Based Field‐Effect Transistor for Water Sensing
Abstract Despite significant progress in solution‐processing of 2D materials, it remains challenging to reliably print high‐performance semiconducting channels that can be efficiently modulated in a field‐effect transistor (FET). Herein, electrochemically exfoliated MoS 2 nanosheets are inkjet‐printed into ultrathin semiconducting channels, resulting in high on/off current ratios up to 10 3 . The reported printing strategy is reliable and general for thin film channel fabrication even in the presence of the ubiquitous coffee‐ring effect. Statistical modeling analysis on the printed pattern profiles suggests that a spaced parallel printing approach can overcome the coffee‐ring effect during inkjet printing, resulting in uniform 2D flake percolation networks. The uniformity of the printed features allows the MoS 2 channel to be hundreds of micrometers long, which easily accommodates the typical inkjet printing resolution of tens of micrometers, thereby enabling fully printed FETs. As a proof of concept, FET water sensors are demonstrated using printed MoS 2 as the FET channel, and printed graphene as the electrodes and the sensing area. After functionalization of the sensing area, the printed water sensor shows a selective response to Pb 2+ in water down to 2 ppb. This work paves the way for additive nanomanufacturing of FET‐based sensors and related devices using 2D nanomaterials.
Additive‐Free Aqueous MXene Inks for Thermal Inkjet Printing on Textiles
Abstract Direct printing of functional inks onto flexible substrates allows for scalable fabrication of wearable electronics. However, existing ink formulations for inkjet printing require toxic solvents and additives, which make device fabrication more complex, limit substrate compatibility, and hinder device performance. Even water‐based carbon or metal nanoparticle inks require supplemental surfactants, binders, and cosolvents to produce jettable colloidal suspensions. Here, a general approach is demonstrated for formulating conductive inkjet printable, additive‐free aqueous Ti 3 C 2 T x MXene inks for direct printing on various substrates. The rheological properties of the MXene inks are tuned by controlling the Ti 3 C 2 T x flake size and concentration. Ti 3 C 2 T x ‐based electrical conduits and microsupercapacitors (MSCs) are printed on textile and paper substrates by optimizing the nozzle geometry for high‐resolution inkjet printing. The chemical stability and electrical properties of the printed devices are also studied after storing the devices for six months under ambient conditions. Current collector‐free, textile‐based MSCs show areal capacitance values up to 294 mF cm −2 (2 mV s −1 ) in poly(vinyl alcohol)/sulfuric acid gel electrolyte, surpassing reported printed MXene‐based MSCs and inkjet‐printed MSCs using other 2D nanomaterials. This work is an important step toward increasing the functional capacity of conductive inks and simplifying the fabrication of wearable textile‐based electronics.
A Review of Inkjet Printed Graphene and Carbon Nanotubes Based Gas Sensors
Graphene and carbon nanotube (CNT)-based gas/vapor sensors have gained much traction for numerous applications over the last decade due to their excellent sensing performance at ambient conditions. Inkjet printing various forms of graphene (reduced graphene oxide or modified graphene) and CNT (single-wall nanotubes (SWNTs) or multiwall nanotubes (MWNTs)) nanomaterials allows fabrication onto flexible substrates which enable gas sensing applications in flexible electronics. This review focuses on their recent developments and provides an overview of the state-of-the-art in inkjet printing of graphene and CNT based sensors targeting gases, such as NO 2 , Cl 2 , CO 2 , NH 3 , and organic vapors. Moreover, this review presents the current enhancements and challenges of printing CNT and graphene-based gas/vapor sensors, the role of defects, and advanced printing techniques using these nanomaterials, while highlighting challenges in reliability and reproducibility. The future potential and outlook of this rapidly growing research are analyzed as well.
A Reactive Inkjet Printing Process for Fabricating Biodegradable Conductive Zinc Structures
A novel reactive inkjet printing (RIJ) process for fabricating environmentally benign, conductive zinc structures on biodegradable substrates is reported. A precursor consisting of oxidized zinc microparticles is formulated into a viscous ink for high‐resolution, high‐repeatability screen printing. A single RIJ process is performed to selectively dispense an acid‐based oxide etching agent onto the screen‐printed zinc ink to significantly improve its electrical conductivity, up to 4 × 10 4 S m −1 . The RIJ process enables precise control of the amount of deposited etching agent, allowing control of conductivity and avoiding damage caused by excessive acid exposure. The RIJ process deposits the etching agent selectively on the screen‐printed, water‐soluble zinc patterns, thus preserving the print fidelity by avoiding ink smearing that can occur when using a blanket treatment such as submersion. A printed biodegradable antenna with a minimum feature size of 500 μm for use with a batteryless radio frequency identification (RFID) chip is fabricated as demonstration. Due to the higher ink conductivity and improved pattern fidelity, the antenna fabricated by the RIJ process shows a ≈2.2× increase in reading distance compared with a similar antenna that is screen printed and activated using a drop‐casting process.
The Influence of Microstructure on TCR for Inkjet-Printed Resistive Temperature Detectors Fabricated Using AgNO 3 /Ethylene-Glycol-Based Inks
This study investigated the influence of microstructure on the performance of Ag inkjet-printed, resistive temperature detectors (RTDs) fabricated using particle-free inks based on a silver nitrate (AgNO 3 ) precursor and ethylene glycol as the ink solvent. Specifically, the temperature coefficient of resistance (TCR) and sensitivity for sensors printed using inks that use monoethylene glycol (mono-EG), diethylene glycol (di-EG), and triethylene glycol (tri-EG) and subjected to a low-pressure argon (Ar) plasma after printing were investigated. Scanning electron microscopy (SEM) confirmed previous findings that microstructure is strongly influenced by the ink solvent, with mono-EG inks producing dense structures, while di- and tri-EG inks produce porous structures, with tri-EG inks yielding the most porous structures. RTD testing revealed that sensors printed using mono-EG ink exhibited the highest TCR (1.7 × 10 -3 /°C), followed by di-EG ink (8.2 × 10 -4 /°C) and tri-EG ink (7.2 × 10 -4 /°C). These findings indicate that porosity exhibits a strong negative influence on TCR. Sensitivity was not strongly influenced by microstructure but rather by the resistance of RTD. The highest sensitivity (0.84 Ω/°C) was observed for an RTD printed using mono-EG ink but not under plasma exposure conditions that yield the highest TCR.
Inkjet Printing to Scale Perovskite and Silicon Tandem Solar Cell: Cooperative Research and Development Final Report, CRADA Number CRD-17-00690
The proposed project seeks to develop a method for inkjet printing of the active layer in perovskite solar cells for application in stand-alone products or added to conventional silicon solar cells in a mechanically-stacked tandem configuration. This technology presents significant advanced manufacturing challenges and opportunities in getting to scale, including development of novel uses for printing technologies and development of predictive quality control techniques.
Origami Terahertz Detectors Realized by Inkjet Printing of Carbon Nanotube Inks
Terahertz (THz) technology has shown promise for several applications, but limitations in sources and detectors have prevented broader adoption. Existing THz detectors are rigid, planar, and fabricated using complex technology, making it difficult to integrate into systems. Here we demonstrate THz detectors fabricated by inkjet printing on submicrometer thick, ultraflexible substrates. By developing p- and n-type carbon nanotube inks, we achieve optically thick p–n junction and p-type devices, enabling antenna-free pixels for THz imaging. By further designing and folding the printed devices, we realize origami-inspired architectures with improved performance over single devices, achieving a noise-equivalent power of 12 nW/Hz 1/2 at room temperature with no voltage bias. Finally, our approach opens avenues for nonplanar, foldable, deployable, insertable, and retractable THz detectors for applications in nondestructive inspection.
Inkjet-printed Ce-doped SnO x electron transport layer for improved performance of planar perovskite solar cells
Inkjet-printed Ce-doped SnO x ETLs achieved improved photovoltaic performance originating from the increased conductivity, suppressed surface defects, and improved energy level alignment at the ETL/perovskite interface, compared to undoped SnO x ETLs.
Statistical Modeling and Analysis of k -Layer Coverage of Two-Dimensional Materials in Inkjet Printing Processes
Two-dimensional layered materials/flakes, also known as crystalline atom-thick layer nanosheets, have recently been receiving great attention in electronics fabrication due to their unique and intriguing properties. The k-layer coverage area (i.e., the area covered by k number of overlapping layers) of the printed flake pattern significantly impacts on the properties of the printed electronics. In this work, we constructed a statistical model to describe the k-layer coverage of randomly distributed two-dimensional materials. A series of results are obtained to provide not only the expectation but also the variance of the coverage area. The boundary effects on the random flakes coverage are also studied. In addition, an approximated statistical testing approach is also developed in this work to detect abnormal coverage patterns. Furthermore, the case studies based on simulated data and real flakes images obtained from the inkjet printing process demonstrate the accuracy and effectiveness of the proposed model and analysis methods.
A Microchannel Heat Exchanger Produced From a Metal Matrix Composite by Hybrid Laser Powder Bed Fusion and Inkjet Printing
Abstract This paper explores the production of an oxide dispersion strengthened (ODS) 304L stainless steel microchannel heat exchanger (HX) using a hybrid additive manufacturing process of laser powder bed fusion and inkjet printing. The study investigates the capabilities and economics of the hybrid inkjet-laser powder bed fusion (LPBF) process and evaluates the dimensional accuracy, functionality, and mechanical properties of the resulting ODS alloy. The effectiveness and pressure drop of the ODS heat exchangers produced by the hybrid LPBF tool are also determined. Results show that the inkjet-doped samples have a lower mean channel height with higher standard deviation than samples produced by LPBF alone. This is attributed to greater absorption of laser energy for the powder coated with the oxide precursor. The economic analysis shows that the hybrid process has a potential for reducing the unit cost of the heat exchanger based on cost modeling assumptions.
Introduction of Chalcogenide Glasses to Additive Manufacturing: Nanoparticle Ink Formulation, Inkjet Printing, and Phase Change Devices Fabrication
Abstract Chalcogenide glasses are one of the most versatile materials that have been widely researched because of their flexible optical, chemical, electronic, and phase change properties. Their application is usually in the form of thin films, which work as active layers in sensors and memory devices. In this work, we investigate the formulation of nanoparticle ink of Ge–Se chalcogenide glasses and its potential applications. The process steps reported in this work describe nanoparticle ink formulation from chalcogenide glasses, its application via inkjet printing and dip-coating methods and sintering to manufacture phase change devices. We report data regarding nanoparticle production by ball milling and ultrasonication along with the essential characteristics of the formed inks, like contact angle and viscosity. The printed chalcogenide glass films were characterized by Raman spectroscopy, X-ray diffraction, energy dispersive spectroscopy and atomic force microscopy. The printed films exhibited similar compositional, structural, electronic and optical properties as the thermally evaporated thin films. The crystallization processes of the printed films are discussed compared to those obtained by vacuum thermal deposition. We demonstrate the formation of printed thin films using nanoparticle inks, low-temperature sintering and proof for the first time, their application in electronic and photonic temperature sensors utilizing their phase change property. This work adds chalcogenide glasses to the list of inkjet printable materials, thus offering an easy way to form arbitrary device structures for optical and electronic applications.
Anisotropic Thermal Conductivity of Inkjet-Printed 2D Crystal Films: Role of the Microstructure and Interfaces
Two-dimensional (2D) materials are uniquely suited for highly anisotropic thermal transport, which is important in thermoelectrics, thermal barrier coatings, and heat spreaders. Solution-processed 2D materials are attractive for simple, low-cost, and large-scale fabrication of devices on, virtually, any substrate. However, to date, there are only few reports with contrasting results on the thermal conductivity of graphene films, while thermal transport has been hardly measured for other types of solution-processed 2D material films. In this work, inkjet-printed graphene, h-BN and MoS2 films are demonstrated with thermal conductivities of ∼10 Wm−1K−1 and ∼0.3 Wm−1K−1 along and across the basal plane, respectively, giving rise to an anisotropy of ∼30, hardly dependent on the material type and annealing treatment. First-principles calculations indicate that portion of the phonon spectrum is cut-off by the quality of the thermal contact for transport along the plane, yet the ultra-low conductivity across the plane is associated with high-transmissivity interfaces. These findings can drive the design of highly anisotropic 2D material films for heat management applications.
Inkjet printing of epitaxially connected nanocrystal superlattices
Access to a blossoming library of colloidal nanomaterials provides building blocks for complex assembled materials. The journey to bring these prospects to fruition stands to benefit from the application of advanced processing methods. Epitaxially connected nanocrystal (or quantum dot) superlattices present a captivating model system for mesocrystals with intriguing emergent properties. The conventional processing approach to creating these materials involves assembling and attaching the constituent nanocrystals at the interface between two immiscible fluids. Processing small liquid volumes of the colloidal nanocrystal solution involves several complexities arising from the concurrent spreading, evaporation, assembly, and attachment. The ability of inkjet printers to deliver small (typically picoliter) liquid volumes with precise positioning is attractive to advance fundamental insights into the processing science, and thereby potentially enable new routes to incorporate the epitaxially connected superlattices into technology platforms. In this study, we identified the processing window of opportunity, including nanocrystal ink formulation and printing approach to enable delivery of colloidal nanocrystals from an inkjet nozzle onto the surface of a sessile droplet of the immiscible subphase. We demonstrate how inkjet printing can be scaled-down to enable the fabrication of epitaxially connected superlattices on patterned sub-millimeter droplets. Furthermore, we anticipate that insights from this work will spur on future advances to enable more mechanistic insights into the assembly processes and new avenues to create high-fidelity superlattices.
Green synthesis of germanium nano ink and inkjet printing of Si/Ge heterostructure
Not Available