Inorganic Solid Electrolyte Interphase Engineering Rationales Inspired by Hexafluorophosphate Decomposition Mechanisms
Not Available
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
SEARCH · Search NASA
Results for “inorganic solid electrolytes”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Solid inorganic electrolyte regenerative fuel cell system.
Electrochemical properties of zirconium phosphate membranes containing zeolites related to independent electrolysis, fuel cell operation and regenerative fuel cell cycle
Berger, C.↗
Realizing high-capacity all-solid-state lithium-sulfur batteries using a low-density inorganic solid-state electrolyte
Abstract Lithium-sulfur all-solid-state batteries using inorganic solid-state electrolytes are considered promising electrochemical energy storage technologies. However, developing positive electrodes with high sulfur content, adequate sulfur utilization, and high mass loading is challenging. Here, to address these concerns, we propose using a liquid-phase-synthesized Li 3 PS 4 -2LiBH 4 glass-ceramic solid electrolyte with a low density (1.491 g cm −3 ), small primary particle size (~500 nm) and bulk ionic conductivity of 6.0 mS cm −1 at 25 °C for fabricating lithium-sulfur all-solid-state batteries. When tested in a Swagelok cell configuration with a Li-In negative electrode and a 60 wt% S positive electrode applying an average stack pressure of ~55 MPa, the all-solid-state battery delivered a high discharge capacity of about 1144.6 mAh g −1 at 167.5 mA g −1 and 60 °C. We further demonstrate that the use of the low-density solid electrolyte increases the electrolyte volume ratio in the cathode, reduces inactive bulky sulfur, and improves the content uniformity of the sulfur-based positive electrode, thus providing sufficient ion conduction pathways for battery performance improvement.
25 ENERGY STORAGE↗
Boosting the interfacial superionic conduction of halide solid electrolytes for all-solid-state batteries
Designing highly conductive and (electro)chemical stable inorganic solid electrolytes using cost-effective materials is crucial for developing all-solid-state batteries. Here, we report halide nanocomposite solid electrolytes (HNSEs) ZrO 2 (-ACl)-A 2 ZrCl 6 (A = Li or Na) that demonstrate improved ionic conductivities at 30 °C, from 0.40 to 1.3 mS cm -1 and from 0.011 to 0.11 mS cm -1 for Li + and Na + , respectively, compared to A 2 ZrCl 6 , and improved compatibility with sulfide solid electrolytes. The mechanochemical method employing Li 2 O for the HNSEs synthesis enables the formation of nanostructured networks that promote interfacial superionic conduction. Via density functional theory calculations combined with synchrotron X-ray and 6 Li nuclear magnetic resonance measurements and analyses, we demonstrate that interfacial oxygen-substituted compounds are responsible for the boosted interfacial conduction mechanism. Compared to state-of-the-art Li 2 ZrCl 6 , the fluorinated ZrO 2 -2Li 2 ZrCl 5 F HNSE shows improved high-voltage stability and interfacial compatibility with Li 6 PS 5 Cl and layered lithium transition metal oxide-based positive electrodes without detrimentally affecting Li + conductivity. We also report the assembly and testing of a Li-In||LiNi 0.88 Co 0.11 Mn 0.01 O 2 all-solid-state lab-scale cell operating at 30 °C and 70 MPa and capable of delivering a specific discharge of 115 mAh g -1 after almost 2000 cycles at 400 mA g -1 .
36 MATERIALS SCIENCE↗
Li 2 GeS 3 : Lithium Ionic Conductor with an Unprecedented Structural Type
Lithium-ion batteries (LIBs) are widely used in electric vehicles, mobile electronic devices, and large-scale stationary energy storage systems. However, their liquid electrolytes present significant safety concerns due to their inherent flammability. To address this, the focus has shifted toward all-solid-state batteries (ASSBs) utilizing inorganic solid electrolytes that promise enhanced safety. In this work, we report the discovery of a new crystal structural type of Li-ion conductor, Li 2 GeS 3 , with a unique structure, synthesized by a solid-state reaction from Li 2 S and GeS 2 . It was first reported in 2000 with an orthorhombic unit cell, but its detailed crystal structure remains veiled. Here, we have unveiled its structure for the first time, employing an ab initio structure determination technique from powder X-ray and time-of-flight neutron diffraction data. The compound has an unprecedented crystal structural type with a hexagonal $P6_1$ symmetry and a unit cell of α = 6.79364(4) Å and c = 17.90724(14) Å. Its structure is comprised of a distorted hexagonal close-packed arrangement of sulfur anions with three asymmetric metal atoms: Li1, Li2, and Ge are in tetrahedral cavities surrounded by sulfur atoms. The ionic conductivity of Li 2 GeS 3 was measured to be 1.63 × 10 –8 S cm –1 at 303 K and 2.45 × 10 –7 S cm –1 at 383 K. Bond valence energy landscape calculations revealed three-dimensional lithium diffusion pathways within the structure. This novel crystal structure in Li 2 GeS 3 holds the potential for developing high-performance ionic conductors through suitable chemical substitution and offers valuable insights into designing new ionic conductors for ASSBs.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Flux Synthesis of A-site Disordered Perovskite La 0.5 M 0.5 TiO 3 (M$=$Li, Na, K) Nanorods Tailored for Solid Composite Electrolytes
Inorganic fillers play an important role in improving the ionic conductivity of solid composite electrolytes (SCEs) for Li-ion batteries. Among inorganic fillers, perovskite-type lithium lanthanum titanate (LLTO) stands out for its high bulk Li + conductivity on the order of 10 -3 S cm -1 at room temperature. According to a literature survey, the optimal LLTO filler should possess the following characteristics: i) a single-crystal structure to minimize grain boundaries; ii) a small particle size to increase the filler/polymer interface area; iii) a 1D morphology for efficient interface channels; and iv) cubic symmetry to facilitate rapid bulk Li + diffusion within the filler. However, the synthesis of single crystal, 1D LLTO nanomaterials with cubic symmetry is challenging. Herein, a flux strategy is developed to synthesize La 0.5 M 0.5 TiO 3 (LMTO, M$=$Li, Na, and K) single-crystal nanorods with an A-site-disordered, cubic perovskite phase. The flux media promotes the oriented growth of nanorods, prevents nanorods from sintering, and provides multiple alkali metal ion doping at M sites to stabilize the cubic phase. SCEs compositing the Li + -conducting LMTO nanorods as fillers and poly[vinylene carbonate- co -lithium sulfonyl(trifluoromethane sulfonyl)imide methacrylate] matrix exhibit more than twice the conductivity of the neat polymer electrolyte (30.6 vs 14.0 µS cm -1 at 303 K).
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Lithium Dendrite-Free Li 7 N 2 I-LiOH Solid Electrolytes for High Energy Lithium Batteries
All-solid-state lithium batteries (ASSLBs) hold great potential to improve the safety and energy density of today’s lithium-ion batteries by using non-flammable inorganic solid electrolytes. Solid electrolytes (SEs) are believed to prevent Li dendrite growth because of high mechanical strength and high Li+ transference numbers. Significant advances in SE have been achieved, among which, Li7La3Zr2O12 (LLZO) and Li2S–P2S5 (LPS) are the most promising SEs for bulk-type solid-state lithium batteries because of high ionic conductivities (>10-4 S/cm2). However, in contrast to our expectations, the growth of lithium dendrites is not suppressed but is facilitated in LLZOs and LPSs regardless of dopants, porosity, and crystallinity of the electrolytes. Despite the unity Li transference number and over two-times of shear modulus than that of Li metal, the critical current densities for Li plating and stripping in these SEs are less than 1.0 mA cm-2, which is one-fourth to one-tenth of that in liquid electrolytes at room temperature. The incompatibility between LLZO and LPS with Li metal seriously limits the energy density of all-solid-state batteries. The mechanism for lithium dendrite formation and growth in SEs are still disputable. Lack of understanding of the Li dendrite formation mechanism seriously impeded the development of solid-state lithium batteries. The development of the criterion for Li dendrite suppression is essential for the success of solid electrolyte lithium batteries. In this project, a criterion for Li dendrite suppression will be developed through thermodynamics and kinetics analysis of lithium dendrite nucleation/growth, which will guide the solid-state electrolyte design. Li7N2I-LiOH, Li5NI2-LiOH and Li3YCl6 solid electrolyte with high ionic conductivity and low electronic conductivity were used to validate the criterion for lithium dendrite suppression. Different surface modifications were also explored to enhance the dendrite suppression capability of SSEs.
25 ENERGY STORAGE↗
Crack‐Free Single‐Crystalline LiNiO 2 for High Energy Density All‐Solid‐State Batteries
Abstract Single‐crystalline layered oxide (LiNi 1‐ x ‐ y Mn x Co y O 2 ) cathodes have been found to exhibit exceptional electrochemical properties when coupled with various inorganic solid electrolytes (ISEs) in all‐solid‐state batteries (ASSBs). Their advantages stem from the robust morphological integrity with the absence of grain boundaries and the high electrochemical oxidative stability. Here, ASSBs featuring single‐crystalline LiNiO 2 (LNO) with the highest Ni content are reported, offering a high theoretical specific capacity of 275 mAh g ‐1 alongside a high average discharge voltage (3.7 V vs Li + /Li). Through a careful investigation, it is demonstrated that micron‐sized single‐crystalline LNO (µSC‐LNO) composite cathodes with a halide ISE exhibit a high initial discharge capacity of 205 mAh g ‐1 with an outstanding cycle performance over 200 cycles in room‐temperature ASSBs. The significance of engineering parameters is emphasized, such as particle size and specific density, in promoting a homogeneous and fast Li + transport within the composite cathodes. Furthermore, the formation of undesirable interphase between the halide ISE in the cathode and sulfide ISE separator is elucidated, which may be a critical factor impeding long‐term cyclability of ASSBs. This work provides insights into the design of composite cathodes for high‐energy‐density ASSBs.
Chemistry↗
Stable Cycling with Intimate Contacts Enabled by Crystallinity–Controlled PTFE–Based Solvent–Free Cathodes in All–Solid–State Batteries
All-solid-state batteries (ASSBs) employing Li-metal anodes and inorganic solid electrolytes are attracting great attention due to high safety and energy density for next-generation energy storage devices. However, the volume change of cathode active materials can cause contact loss, resulting in charge carrier isolation, heterogeneous current distribution, and poor electrochemical properties in ASSBs. Here, a simple, yet effective, solvent-free electrode engineering approach with polytetrafluoroethylene (PTFE) as a binder for ASSBs is reported, enabling intimate contact and stable interfaces with the cathode. It is substantiated that the crystallinity of PTFE can be controlled depending on the heat history, and highly crystalline PTFE displays robust mechanical properties. High-nickel LiNi 0.8 Mn 0.1 Co 0.1 O 2 cathode prepared with crystalline PTFE show improved cycle and rate performances in ASSBs. In addition, it is revealed that the intimate contact between cathode particles with a stable cathode electrolyte layer is maintained during cycling by postmortem studies. Furthermore, this simple engineering method can be applied to prepare cathodes with a variety of active materials and solid electrolytes in ASSBs.
25 ENERGY STORAGE↗
Kinetic pathways of fast lithium transport in solid electrolyte interphases with discrete inorganic components
The transport of lithium ions in the solid electrolyte interphase (SEI) has been previously accepted to proceed in two steps: a fast pore diffusion through the outer, porous organic layer followed by a slow knock-off or vacancy diffusion in the inner, dense inorganic layer. The second step is believed to be the rate-limiting step during fast-charging. In this study, we have intentionally constructed a thicker SEI (SEI-rich) structure on the surface of monoclinic Nb 2 O 5 (H-Nb 2 O 5 ) by adding LiNO 3 into a conventional ethylene carbonate based electrolyte. The electrochemical performance of two electrodes, one SEI-rich and one with few SEI (SEI-lean), was found to be almost the same, including their fast-charging capability and cycling stability, despite the significant difference in their SEI structure. Importantly, analysis using cryogenic scanning/transmission electron microscopy showed the discrete decoration of individual inorganic particles (e.g., Li 2 O) and amorphous species (LiN x O y /organic components) over the surface of H-Nb 2 O 5 . These discrete inorganic particles are in contradiction to the formation of dense inner inorganic layer, which has been commonly postulated. Based on these findings, we propose a new mechanism for Li ion transport through the SEI: one-step pore diffusion, without the second step slow diffusion. This one-step pore diffusion process provides an extremely fast Li ion transport, and effectively removes the kinetic limitation of Li ion transport in the SEI for fast charging. Finally, these results strongly suggest that the influence of SEI structure on the transport kinetics of lithium ions is much less significant than previously accepted. These results offer a new understanding of possible lithium ion transport pathway within SEI and may have implications for the future designs of fast-charging battery materials.
25 ENERGY STORAGE↗
In Situ Alloying Enabled by Active Liquid Metal Filler for Self‐Healing Composite Polymer Electrolytes
Abstract Solid inorganics, known for kinetically inhibiting polymer crystallization and enhancing ionic conductivity, have attracted significant attention in solid polymer electrolytes. However, current composite polymer electrolytes (CPEs) are still facing challenges in Li metal batteries, falling short of inhibiting severe dendritic growth and resulting in very limited cycling life. This study introduces Ga 62.5 In 21.5 Sn 16 (Galinstan) liquid metal (LM) as an active liquid alternative to conventional passive solid fillers, aiming at realizing self‐healing protection against dendrite problems. Compared to solid inorganics, for example silica, LM droplets could more significantly reduce polymer crystallinity and enhance Li‐ion conductivity due to their liquid nature, especially at temperatures below the polymer melting point. More importantly, LMs are unraveled as dynamic chemical traps, which are capable of blocking and consuming lithium dendrites upon contact via in situ alloying during battery operation and further inhibiting dendritic growth due to the lower deposition energy barrier of the formed Li‐LM alloy. As a proof of concept, by strategically designing an asymmetric CPE with the active LM filling, a solid‐state Li/LiFePO 4 battery achieves promising full‐cell functionality with notable rate performance and stable cycle life. This active filler‐mediated self‐healing approach could bring new insights into the battery design in versatile solid‐state systems.
Wu, Kai↗
Progress and Prospects of Inorganic Solid-State Electrolyte-Based All-Solid-State Pouch Cells
Here, all-solid-state batteries have piqued global research interest because of their unprecedented safety and high energy density. Significant advances have been made in achieving high room-temperature ionic conductivity and good air stability of solid-state electrolytes (SSEs), mitigating the challenges at the electrode–electrolyte interface, and developing feasible manufacturing processes. Along with the advances in fundamental study, all-solid-state pouch cells using inorganic SSEs have been widely demonstrated, revealing their immense potential for industrialization. This review provides an overview of inorganic all-solid-state pouch cells, focusing on ultrathin SSE membranes, sheet-type thick solid-state electrodes, and bipolar stacking. Moreover, several critical parameters directly influencing the energy density of all-solid-state Li-ion and lithium–sulfur pouch cells are outlined. Finally, perspectives on all-solid-state pouch cells are provided and specific metrics to meet certain energy density targets are specified. This review looks to facilitate the development of inorganic all-solid-state pouch cells with high energy density and excellent safety.
25 ENERGY STORAGE↗
Solid-state battery designed for electric aviation
The demand for higher energy density batteries increases as the demand for portable electronic devices and electric automotive increases, as well as a variety of other applications requiring substantially higher power and energy than attainable with current lithium-ion capabilities which includes the areas of high performance vehicles, military applications, and electric aviation. However, the improvement of energy density is insufficient alone for enabling electric aviation when considering the high flammability and risk of thermal runaway inherent in current state-of-the-art liquid electrolytes. The development of high energy, high power, and safe batteries are required to enable hybrid and fully electric aircraft. Next generation chemistries such as lithium-sulfur provide high theoretical specific energy density suitable for electric aviation without as strict of volumetric requirements observed in the automotive industry. However, due to the phase transition during discharge where sulfur generates a series of soluble intermediate polysulfides, which are lost to the liquid electrolyte, cause detrimental side effects, and severely limit cycle life battery performance is severely reduced. Additionally, the low electrical conductivity of sulfur requires a large amount of inactive carbon dramatically increasing parasitic mass. The dissolution issue make sulfur a desirable candidate to pair with a solid-state electrolyte in order to avoid polysulfide dissolution and shuttling. In addition, inorganic solid-electrolytes have low flammability providing the improved safety required. Combining this chemistry with a solid-state electrolyte provides a path for achieving the energy and safety required for electric aviation. The development of scalable thin solid-state electrolytes paired with lithium-sulfur chemistry will be discussed and how their development will aid in enabling a unique application.
Donald A. Dornbusch↗
Salt‐in‐Salt Reinforced Carbonate Electrolyte for Li Metal Batteries
Abstract The instability of carbonate electrolyte with metallic Li greatly limits its application in high‐voltage Li metal batteries. Here, a “salt‐in‐salt” strategy is applied to boost the LiNO 3 solubility in the carbonate electrolyte with Mg(TFSI) 2 carrier, which enables the inorganic‐rich solid electrolyte interphase (SEI) for excellent Li metal anode performance and also maintains the cathode stability. In the designed electrolyte, both NO 3 − and PF 6 − anions participate in the Li + ‐solvent complexes, thus promoting the formation of inorganic‐rich SEI. Our designed electrolyte has achieved a superior Li CE of 99.7 %, enabling the high‐loading NCM811||Li (4.5 mAh cm −2 ) full cell with N/P ratio of 1.92 to achieve 84.6 % capacity retention after 200 cycles. The enhancement of LiNO 3 solubility by divalent salts is universal, which will also inspire the electrolyte design for other metal batteries.
Liu, Sufu↗
Salt‐in‐Salt Reinforced Carbonate Electrolyte for Li Metal Batteries
Abstract The instability of carbonate electrolyte with metallic Li greatly limits its application in high‐voltage Li metal batteries. Here, a “salt‐in‐salt” strategy is applied to boost the LiNO 3 solubility in the carbonate electrolyte with Mg(TFSI) 2 carrier, which enables the inorganic‐rich solid electrolyte interphase (SEI) for excellent Li metal anode performance and also maintains the cathode stability. In the designed electrolyte, both NO 3 − and PF 6 − anions participate in the Li + ‐solvent complexes, thus promoting the formation of inorganic‐rich SEI. Our designed electrolyte has achieved a superior Li CE of 99.7 %, enabling the high‐loading NCM811||Li (4.5 mAh cm −2 ) full cell with N/P ratio of 1.92 to achieve 84.6 % capacity retention after 200 cycles. The enhancement of LiNO 3 solubility by divalent salts is universal, which will also inspire the electrolyte design for other metal batteries.
25 ENERGY STORAGE↗
A Fluoride-Rich Solid-Like Electrolyte Stabilizing Lithium Metal Batteries
To address the problems associated with Li metal anodes, a fluoride-rich solid-like electrolyte (SLE) that combines the benefits of solid-state and liquid electrolytes is presented. Its unique triflate-group-enhanced frame channels facilitate the formation of a functional inorganic-rich solid electrolyte interphase (SEI), which not only improves the reversibility and interfacial charge transfer of Li anodes but also ensures uniform and compact Li deposition. Furthermore, these triflate groups contribute to the decoupling of Li + and provide hopping sites for rapid Li + transport, enabling a high room-temperature ionic conductivity of 1.1 mS cm -1 and a low activation energy of 0.17 eV, making it comparable to conventional liquid electrolytes. Consequently, Li symmetric cells using such SLE achieve extremely stable plating/stripping cycling over 3500 h at 0.5 mA cm -2 and support a high critical current up to 2 mA cm -2 . Here, the assembled Li||LiFePO 4 solid-like batteries exhibit exceptional cyclability for over 1 year and a half, even outperforming liquid cells. Additionally, high-voltage cylindrical cells and high-capacity pouch cells are demonstrated, corroborating much simpler processibility in battery assembly compared to all-solid-state batteries.
25 ENERGY STORAGE↗
High-Voltage Sodium–Metal Batteries with Asymmetric Fluoroalkoxylated Organoborate Anion Chemistry
The high reactivity of sodium (Na) metal restricts its compatibility to ether-based electrolytes, while the poor oxidative stability of ethers precludes their coupling to high-voltage cathodes, fundamentally limiting the operating voltage and energy density of sodium–metal batteries (SMBs). We present here a coordination-asymmetry strategy to reconcile this thermodynamic mismatch by generating in situ an asymmetric fluoroalkoxylated organoborate anion, [FB(OCH(CF 3 ) 2 ) 3 ] − (BOF – ), via a Lewis acid–base adduct reaction in ether electrolyte. The asymmetric ligand architecture differentiates oxidative and fluorination pathways: oxidizable B–O moieties mediate controlled interfacial reconstruction, whereas the terminal B–F units supply fluorine for chemical passivation. This self-adaptive chemistry yields nanoscale, conformal, compositionally graded interphases: a boron-oxide/boron-oxycarbide-rich cathode-electrolyte interphase (CEI) that mitigates ether oxidation and a bilayered inorganic–organic solid–electrolyte interphase (SEI) that regulates Na deposition. The nanostructured interphases enable highly reversible Na plating/stripping with an average Coulombic efficiency (CE) of 99.98% and sustain stable 4.3 V operation of anode-free SMBs in oxidation-prone ether electrolytes. Furthermore, this work establishes asymmetric boron coordination as a molecular-level design principle for creating chemically adaptive interphases that overcome the redox asymmetry in energy-dense electrochemical systems.
Anions↗
Advancements in active filler-contained polymer solid-state electrolytes for lithium-metal batteries: A concise review
Lithium-metal batteries (LMBs) usually are regarded as the pinnacle of next-generation energy storage due to the high specific capacity and low redox potential of the Li-metal anode. However, their development is hindered by safety hazards related to flammable electrolytes and uncontrolled side reactions within the battery. Both polymer and solid-state inorganic electrolytes, despite their potential, exhibit shortcomings that limit their practical applications. Active filler-containing polymer electrolytes (AFPEs) offer a promising solution by combining the benefits of both types. Enhanced by supramolecular interactions between the polymer matrix and active fillers, AFPEs demonstrate superior electrochemical performance over traditional polymer electrolytes. This review discusses the progress in active fillers and various polymer matrices, examining the factors that enhance performance, particularly ionic conductivity. It also outlines the future research directions of AFPEs, aiming to broaden the application of solid electrolytes in high-performance LMBs.
All solid-state batteries↗