SEARCH · Search NASA
Results for “internal contact”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The L76V Drug Resistance Mutation Decreases the Dimer Stability and Rate of Autoprocessing of HIV-1 Protease by Reducing Internal Hydrophobic Contacts
The mature HIV-1 protease (PR) bearing the L76V drug resistance mutation (PR{sub L76V}) is significantly less stable, with a >7-fold higher dimer dissociation constant (K{sub d}) of 71 {+-} 24 nM and twice the sensitivity to urea denaturation (UC{sub 50} = 0.85 M) relative to those of PR. Differential scanning calorimetry showed decreases in T{sub m} of 12 C for PR{sub L76V} in the absence of inhibitors and 5-7 C in the presence of inhibitors darunavir (DRV), saquinavir (SQV), and lopinavir (LPV), relative to that of PR. Isothermal titration calorimetry gave a ligand dissociation constant of 0.8 nM for DRV, {approx}160-fold higher than that of PR, consistent with DRV resistance. Crystal structures of PR{sub L76V} in complexes with DRV and SQV were determined at resolutions of 1.45-1.46 {angstrom}. Compared to the corresponding PR complexes, the mutated Val76 lacks hydrophobic interactions with Asp30, Lys45, Ile47, and Thr74 and exhibits closer interactions with Val32 and Val56. The bound DRV lacks one hydrogen bond with the main chain of Asp30 in PR{sub L76V} relative to PR, possibly accounting for the resistance to DRV. SQV shows slightly improved polar interactions with PR{sub L76V} compared to those with PR. Although the L76V mutation significantly slows the N-terminal autoprocessing of the precursor TFR-PR{sub L76V} to give rise to the mature PR{sub L76V}, the coselected M46I mutation counteracts the effect by enhancing this rate but renders the TFR-PRM46I/L76V precursor less responsive to inhibition by 6 {micro}M LPV while preserving inhibition by SQV and DRV. The correlation of lowered stability, higher K{sub d}, and impaired autoprocessing with reduced internal hydrophobic contacts suggests a novel molecular mechanism for drug resistance.
Determining Stress Orientation in Rock Valley, Nevada, Using Ambient Seismic Noise
The stress field and the mechanical properties of rocks are important to consider for nuclear explosion monitoring due to their effect on seismic wave radiation from earthquakes and explosions. At the Rock Valley Direct Comparison site, the regional orientation of the maximum horizontal compressive stress (SH max ) is well constrained, but it is unknown whether there are local heterogeneities. Here, I show that stress-induced anisotropy in nonlinear elasticity can be used to estimate the orientation of SH max . Rocks have compliant internal contacts, such as fractures and mineral grain boundaries, that respond to applied strains more strongly than individual mineral crystals. This strain response is asymmetric between compressive and dilatational strains and is affected by anisotropy in the ambient stress field. Traditional seismic velocity measurements are of strain-averaged velocity, which is less sensitive than nonlinear elasticity to the behavior of compliant internal contacts and therefore the stress field and fracture behavior. My results show that the orientation of SH max measured using ambient seismic noise aligns with regional estimates, with some heterogeneity that can also be explained by the limitations of the seismic array. I demonstrate the potential of a passive technique for monitoring the stress field in places that currently lack local measurements.
Crash Models for Advanced Automotive Batteries: A Review of the Current State of the Art
Safety is a critical aspect of lithium-ion (Li-ion) battery design. Impact/crash conditions can trigger a complex interplay of mechanical contact, heat generation and electrical discharge, which can result in adverse thermal events. The cause of these thermal events has been linked to internal contact between the opposite electrodes, i.e. internal short circuit. The severity of the outcome is influenced by the configuration of the internal short circuit and the battery state. Different loading conditions and battery states may lead to micro (soft) shorts where material burnout due to generated heat eliminates contact between the electrodes, or persistent (hard) shorts which can lead to more significant thermal events and potentially damage the entire battery system and beyond. Experimental characterization of individual battery components for the onset of internal shorts is limited, since it is impractical to canvas all possible variations in battery state of charge, operating conditions, and impact loading in a timely manner. This report provides a survey of modeling and simulation approaches and documents a project initiated and funded by DOT/NHTSA to improve modeling and simulation capabilities in order to design tests that provide leading indicators of failure in batteries. In this project, ORNL has demonstrated a computational infrastructure to conduct impact simulations of Li-ion batteries using models that resolve internal structures and electro-thermo-chemical and mechanical conditions. Initial comparisons to abuse experiments on cells and cell strings conducted at ORNL and Naval Surface Warfare Center (NSWC) at Carderock MD for parameter estimation and model validation have been performed. This research has provided insight into the mechanisms of deformation in batteries (both at cell and electrode level) and their relationship to the safety of batteries.
Nonlinear convergence in contact mechanics: Immersed boundary finite volume
In this report we present an immersed boundary finite volume (IBM) method for simulating quasistatic contact mechanics of linearly elastic domains at small strains. In IBM, all external boundaries and internal contacts of an object are represented by embedded surfaces inside a Cartesian mesh, which need not conform to the grid lines. The contact constraints consist of the non-penetrability condition and Coulomb’s friction law, which are discretized using special interpolation stencils and enforced via penalty parameters. The resulting nonlinear system depends on displacement unknowns only. To solve it, we use the Newton method but find that it diverges frequently. To understand the divergence pattern, we analyze a simplified 2-cell problem and show that the global convergence of Newton cannot be ensured for any choice of penalty parameters. We thus propose a modified Newton solver, which guarantees convergence for the 2-cell problem and is numerically verified to converge for all the challenging simulations considered herein. While both 1 st - and 2 nd -order variants of IBM, in displacement unknowns, are proposed, the modified Newton solver applies only to the 1 st -order variant.
Ignition thresholds of aluminized HMX-based polymer-bonded explosives
Here, the ignition of aluminized HMX-based polymer-bonded explosives (PBXs) under shock loading is studied via mesoscale simulations. The conditions analyzed concern loading pulses of 20 nanoseconds to 0.8 microseconds in duration and impact piston velocities on the order of 400-1000 m/s or loading stresses on the order of 3-14 GPa. The sets of samples studied have stochastically similar microstructures consisting of a bimodal distribution of HMX grains, an Estane binder, and aluminum particles 50-100 µm in diameter. The computational model accounts for constituent elasto-viscoplasticity, viscoelasticity, bulk compressibility, fracture, interfacial debonding, internal contact, bulk and frictional heating, and heat conduction. The analysis focuses on the development of hotspots under different material settings and loading conditions. In particular, the ignition thresholds in the forms of the James relation and the Walker-Wasley relation and the corresponding ignition probability are calculated and expressed as functions of the aluminum volume fraction for the PBXs analyzed. Lastly, it is found that the addition of aluminum raises the ignition thresholds, causing the materials to be less sensitive. Dissipation and heating mechanism changes responsible for this trend are delineated.
GLANCING VIEWS OF THE EARTH: FROM A LUNAR ECLIPSE TO AN EXOPLANETARY TRANSIT
It has been posited that lunar eclipse observations may help predict the in-transit signature of Earth-like extrasolar planets. However, a comparative analysis of the two phenomena addressing in detail the transport of stellar light through the planet's atmosphere has not yet been presented. Here, we proceed with the investigation of both phenomena by making use of a common formulation. Our starting point is a set of previously unpublished near-infrared spectra collected at various phases during the 2008 August lunar eclipse. We then take the formulation to the limit of an infinitely distant observer in order to investigate the in-transit signature of the Earth-Sun system as being observed from outside our solar system. The refraction bending of sunlight rays that pass through Earth's atmosphere is a critical factor in the illumination of the eclipsed Moon. Likewise, refraction will have an impact on the in-transit transmission spectrum for specific planet-star systems depending on the refractive properties of the planet's atmosphere, the stellar size, and the planet's orbital distance. For the Earth-Sun system, at mid-transit, refraction prevents the remote observer's access to the lower {approx}12-14 km of the atmosphere and, thus, also to the bulk of the spectroscopically active atmospheric gases. We demonstrate that the effective optical radius of the Earth in-transit is modulated by refraction and varies by {approx}12 km from mid-transit to internal contact. The refractive nature of atmospheres, a property which is rarely accounted for in published investigations, will pose additional challenges to the characterization of Earth-like extrasolar planets. Refraction may have a lesser impact for Earth-like extrasolar planets within the habitable zone of some M-type stars.
Helmet blastometer
A helmet blastometer for characterizing the direction, speed, magnitude, and duration of a blast event to determine the likelihood of blast-induced traumatic brain injury (biTBI). Time of arrival (TOA) gage sensors are mounted on a rigid outer shell of the helmet each producing a TOA signal in response to a fast rising blast induced positive pressure change above a predetermined threshold. A receiver analyzes the positive pressure changes from the gages to determine direction, speed, and magnitude of a blast. Other TOA gauge sensors can be used to produce a TOA signal in response to a negative pressure change below a predetermined threshold. The positive and negative pressure change TOA signals are used to determine blast duration. A second set of internal contact pressure sensors is connected to an inner liner of the helmet to detect contact pressure on a user's head to determine if biTBI has been sustained.
Development of Internal Non-Contacting Profilomerty Superconducting RF Cavities
Under the scope of this CRADA Microdynamics contributed only by transferring to JLab the control source code (on non-disclosure basis) for the CYCLOPS system that we purchased from them earlier. They invested no additional design or engineering time. They made the business decision that there was no market for this system as a product. We at JLab budgeted in-house funds to work on on continued improvements. Per Costpoint, we spent a total of $21,699 loaded on this project. Additional funds were available to hire a contract programmer to make needed program changes, however, the source language used is an older one, no longer taught or in use. I was unable to find any capable programmer. So, the work came to a halt. The CRADA expired. The system is not presently functional. We estimate that a meaningful redesign would require $250,000 in labor and materials. So, while the promised function of the system would be unique and very helpful for some of our technical trouble-shooting needs, it is presently dead in the water and very, very far down on our unfunded priorities list.
Investigating PID Shunting in Polycrystalline Silicon Modules via Multi-Scale, Multi-Technique Characterization
Here we present a method for calculating the TCO sheet resistance of complete thin film modules using EL imaging. The method uses the characteristic decay of the junction voltage over the width of a cell stripe to derive four simple analytic equations for the TCO sheet resistance and the internal and contact resistances. Experimentally, only the module dark JV curve, Jsc-Voc curve, and electroluminescence imaging is required. Unlike previous methods, the internal and contact resistances of the modules are accounted for, and the method does not require curve fitting. The TCO sheet resistances of four 10cm x 10cm amorphous silicon modules are calculated and show excellent agreement with the experimentally measured values.
Thin Films in Partial Wetting: Internal Selection of Contact-Line Dynamics
When 5 a liquid touches a solid surface, it spreads to minimize the system’s energy. The classic thin-film model describes the spreading as an interplay between gravity, capillarity and viscous forces, but cannot see an end to this process as it does not account for the nonhydrodynamic liquid–solid interactions. Even though these interactions are important only close to the contact line, where the liquid, solid and gas meet, they have macroscopic implications: in the partial-wetting regime, a liquid puddle ultimately stops spreading. We show that 10 by incorporating these intermolecular interactions, the free energy of the system at equilibrium can be cast in a Cahn–Hilliard framework with a height-dependent interfacial tension. Utilizing this free energy, we derive a mesoscopic thin-film model that describes statics and dynamics of liquid spreading in the partial-wetting regime. The height-dependence of the interfacial tension introduces a localized apparent slip in the contact-line region and leads to compactly-supported spreading states. In our model, the contact line dynamics emerge naturally as 15 part of the solution and are therefore nonlocally coupled to the bulk flow. Surprisingly, we find that even in the gravity-dominated regime, the dynamic contact angle follows the Cox–Voinov law.
Accelerated beta radiation aging of interlayer titanium nitride in gallium nitride contacts
Currently, there is no good way to determine the influence of the radiation on the aging of betavoltaic electrical contacts. Here, this work tested a method to accelerate the aging of the contacts inside a betavoltaic by enhancing energy deposition within the interfacial region of interest. An electrical contact of gold-titanium on gallium nitride was aged by exposure to tritium betas and electrons in a beamline. The interface stoichiometry was compared to the electrical performance of the contact. The method to age the betavoltaic component could help predict lifetime performance of the internal electrical contacts and provide assurance of deployment reliability.
Accelerated Beta Radiation Aging of Interlayer Titanium Nitride in Gallium Nitride Contacts
Research conducted under the Laboratory Directed Research and Development Program at Pacific Northwest National Laboratory, a multiprogram national laboratory operated by Battelle for the U.S. Department of Energy. An NNSS author co-authored this paper, and portions of this work were supported by the Mission Support and Test Services, LLC, under Contract No. DE-NA0003624 with the U.S. Department of Energy, National Nuclear Security Administration, NA-10 USDOE NA Office of Defense Programs (NA-10). PNNL-SA-163618 Currently, there is no good way to determine the influence of radiation on the aging of betavoltaic electrical contacts. This work tested a method to accelerate the aging of the contacts inside a betavoltaic by enhancing energy deposition within the interfacial region of interest. An electrical contact of gold-titanium on gallium nitride was aged by exposure to tritium betas and electrons in a beamline. The interface stoichiometry was compared to the electrical performance of the contact. The method to age the betavoltaic component could help predict the lifetime performance of the internal electrical contacts and provide assurance of deployment reliability.
Microwave heating device for internal heating convection experiments, applied to Earth's mantle dynamics
We report the design, construction, and performances of a microwave (MW) heating device for laboratory experiments with non-contact, homogeneous internal heating. The device generates MW radiation at 2.47 GHz from a commercial magnetron supplied by a pulsed current inverter using proprietary, feedback based command and control hardware and software. Specially designed MW launchers direct the MW radiation into the sample through a MW homogenizer, devised to even the MW power distribution into the sample's volume. An adjustable MW circuit adapts the MW generator to the load (i.e., the sample) placed in the experiment chamber. Dedicated heatsinks maintain the MW circuits at constant temperature throughout the experiment. Openings for laser scanning for image acquisition with a CCD camera and for the cooling circuits are protected by special MW filters. The performances of the device are analyzed in terms of heating uniformity, long term output power stability, and load matching. The device is used for small scale experiments simulating Earth's mantle convection. The 30 × 30 × 5 cm{sup 3} convection tank is filled with a water‑based viscous fluid. A uniform and constant temperature is maintained at the upper boundary by an aluminum heat exchanger and adiabatic conditions apply at the tank base. We characterize the geometry of the convective regime as well as its bulk thermal evolution by measuring the velocity field by Particle Image Velocimetry and the temperature field by using Thermochromic Liquid Crystals.
Computational design of metamaterials with self contact
Inverse homogenization in combination with contact modeling, topology optimization and shape optimization is used to design metamaterials with optimized macroscopic response. The homogenization assumes length scale separation which allows the non-linear macroscopic behavior to be obtained by analyzing a single unit cell in a lattice structure. Self contact in the unit cell, which is modeled using a third medium contact method, is leveraged to obtain a complex homogenized response. The inverse homogenization problem is initially formulated as a topology optimization problem, where the macroscopic stress–strain behavior is tuned to our liking. However, it is well known that boundary phenomena are difficult to model in topology optimization and that interface modeling is crucial to accurately analyze contact. For that reason, the boundary representation of the topology optimized design is extracted and used as initial design in a subsequent shape optimization. The behaviors of our designs are verified by performing rigorous post-processing analyzes using conforming meshes and conventional contact formulations.
Energy dissipation in polymer-bonded explosives with various levels of constituent plasticity and internal friction
The ignition of energetic materials (EM) under dynamic loading is mainly controlled by localized temperature spikes known as hotspots. Hotspots occur due to several dissipation mechanisms, including viscoplasticity, viscoelasticity, and internal friction along crack surfaces. In this work, to analyze the contributions of these mechanisms, we quantify the ignition probability, energy dissipation, damage evolution, and hotspot characteristics of polymer-bonded explosives (PBXs) with various levels of constituent plasticity of the energetic phase and internal crack face friction. Using PBX9501 consisting of HMX (Octahydro-1,3,5,7-Tetranitro-1,2,3,5-Tetrazocine) and Estane as a reference material, we analyze variants of this material with several values of the yield stress of the energetic phase and coefficients of internal crack face friction, while other parameters are kept unchanged. The impact loading involves piston velocities between 200 and 1200 m/s. The analysis uses a Lagrangian cohesive finite element framework that explicitly accounts for finite-strain elastic-viscoplastic deformation of the grains, viscoelastic deformation of the binder, arbitrary crack initiation and propagation in the grains and the binder, debonding between the grains and the binder, contact between internal surfaces, friction and frictional heating along internal surfaces, heat generation resulting from inelastic bulk deformation, and heat conduction. To determine the ignition status of the material or “go” or “no-go” state, we use a criterion based on a criticality threshold obtained from chemical kinetics calculations. For PBX with various levels of HMX plasticity and friction, the probability of ignition, the evolution of dissipation caused by plasticity and friction, the density of cracks, and the locations of cracks are quantified. Results show that samples with higher levels of constituent plasticity (lower yield strengths) or lower levels of internal friction are less likely to ignite. The relative importance of plasticity and friction depends on load intensity, with frictional heating decreasing as load intensity increases. Although the overall viscoplastic heating outweighs the overall frictional heating, friction plays a very important role in hotspot development at all load intensities analyzed, owing to the fact that frictional heating is more localized than viscoplastic heating. Finally, the predicted thresholds and ignition probabilities are expressed in a load intensity-load duration relation for PBX with different constituent properties.
A smeared crack modeling framework accommodating multi-directional fracture at finite strains
A generic smeared crack modeling framework predicated on the deformation gradient decomposition (DGD) approach is proposed for use in dynamic fracture problems at finite strains, accommodating failure along multiple mutually orthogonal fracture planes embedded within an independently defined bulk material model. Within this constitutive framework, the traction equilibrium conditions imposed at each failure surface are used to determine the associated crack displacements stored as internal state variables. In general, the enforcement of interfacial equilibrium entails the implicit solution of a non-linear system of equations within the constitutive update procedure. However, if inertial effects arising due to the relative motion of the fractured material are incorporated within the model, the traction equilibrium conditions are shown to give rise to corresponding dynamic equations of motion governing the time-evolution of the crack opening displacements. For dynamic problems, an explicit time-integration procedure is devised to efficiently update the material state, subject to a set of internal frictionless contact constraints to prevent material inversion. Finally, the efficacy of the proposed modeling framework is investigated through several benchmark dynamic fracture problems run within the explicit finite element code DYNA3D.
Decoupling the degradation factors of Ni-rich NMC/Li metal batteries using concentrated electrolytes
Battery degradation results from multiple factors that usually correlate with each other. Electrochemical corrosion of the current collector is one of the main reasons for battery failure, leading to poor internal electrical contact and the dissolution of harmful ions into electrolytes. This phenomenon is especially evident in lithium bistrifluoromethanesulfonimidate (LiTFSI)-based electrolytes, although they have many advantages over conventional lithium hexafluorophosphate (LiPF 6 )-based electrolytes, such as low viscosity, good thermal stability, and stable to water. Recently, highly concentrated electrolytes are found hopeful of inhibiting aluminum's corrosion and boosting new electrolyte development. Here we discuss the solvation structures of liquid electrolytes and decouple the degradation mechanisms of using LiTFSI-based electrolytes in Li(Ni 0.8 Co 0.1 Mn 0.1 )O 2 /Li metal batteries. The results suggest although concentrated electrolytes inhibit the Al corrosion, the growth of lithium dendrites and the protection of the cathode-electrolyte interphase are not significantly improved. Furthermore, this paper provides a paradigm to evaluate the performance of electrolytes comprehensively.