Search NASA⌕ Search

SEARCH · Search NASA

Results for “internal reaction mass”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Internal Reaction Mass Taxonomy and Narrow-Down Study

Internal reaction mass (IRM) wave energy converters (WEC) capture wave energy by reacting against a moving mass that is suspended within their hulls. Due to their hermetically sealed Power Take Off (PTO), compact form factor and relatively simple mooring requirements, the National Renewable Energy Laboratory has identified IRM WECs are good candidates for applications such as ocean observation. A literature review of existing IRM mechanisms lead to the classification of IRM WECs based on their principal method of energy capture and principal axes of operation. The IRM categories include sliding mass, pendular and gyroscopic devices. A narrow down study was conducted to ascertain the most promising mechanisms for further investigation; devices were evaluated based on a decision matrix of weighted criteria that included device power output, prototypability and power to mass ratio. The narrow down study identified the issue of achieving resonance with pendulum-based designs, as well as the poor response produced by reaction to long period waves. Chaotic pendula and methods to multiply agitation were identified as a means to increase power output. Alternative methods of power generation, such as triboelectric nanogenerators, were also identified as a technology that would benefit from multiplied agitation and chaotic motion. This work was funded under the U.S. Department of Energy's Water Power Technologies Office's Powering the Blue Economy portfolio.

ENGINEERING,TIDAL AND WAVE POWER↗
DOE OSTI2022

Internal Standard Triggered-Parallel Reaction Monitoring Mass Spectrometry Enables Multiplexed Quantification of Candidate Biomarkers in Plasma

Despite advances in proteomic technologies, clinical translation of plasma biomarkers remains low, partly due to a major bottleneck between the discovery of candidate biomarkers and costly clinical validation studies. Due to a dearth of multiplexable assays, generally only a few candidate biomarkers are tested, and the validation success rate is accordingly low. Previously, mass spectrometry-based approaches have been used to fill this gap but feature poor quantitative performance and were generally limited to hundreds of proteins. Here, we demonstrate the capability of an internal standard triggered-parallel reaction monitoring (IS-PRM) assay to greatly expand the numbers of candidates that can be tested with improved quantitative performance. The assay couples immunodepletion and fractionation with IS-PRM and was developed and implemented in human plasma to quantify 5176 peptides representing 1314 breast cancer biomarker candidates. Characterization of the IS-PRM assay demonstrated the precision (median % CV of 7.7%), linearity (median R 2 > 0.999 over 4 orders of magnitude), and sensitivity (median LLOQ < 1 fmol, approximately) to enable rank-ordering of candidate biomarkers for validation studies. Using three plasma pools from breast cancer patients and three control pools, 893 proteins were quantified, of which 162 candidate biomarkers were verified in at least one of the cancer pools and 22 were verified in all three cancer pools. The assay greatly expands capabilities for quantification of large numbers of proteins and is well suited for prioritization of viable candidate biomarkers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1968

Dynamics of a rotating space station.

Equations formulated for space vehicle reaction to rotating machinery and internal mass motion, evaluating dynamics of cylindrical space station rotating about major axis

Polstorff, W. K.↗
NASA NTRS1973

Control of spin ambiguity during reorientation of an energy dissipating body

A quasi-rigid body initially spinning about its minor principal axis and experiencing energy dissipation will enter a tumbling mode and eventually reorient itself such that stable spin about its major principal axis is achieved. However, in this final state the body may be spinning in a positive or negative sense with respect to its major axis and aligned in a positive or negative sense with the inertially fixed angular momentum vector. This ambiguity can be controlled only through an active system. The associated dynamical formulations and simulations of uncontrolled reorientations are presented. Three control schemes are discussed and results offered for specific examples. These schemes include displacement of internal masses, spinning up of internal inertia, and reaction jets, all of which have demonstrated the ability to control spin ambiguity.

Kaplan, M. H.↗
NASA NTRS2007

Transient Numerical Modeling of Catalytic Channels

This paper presents a transient model of catalytic combustion suitable for isolated channels and monolith reactors. The model is a lumped two-phase (gas and solid) model where the gas phase is quasi-steady relative to the transient solid. Axial diffusion is neglected in the gas phase; lateral diffusion, however, is accounted for using transfer coefficients. The solid phase includes axial heat conduction and external heat loss due to convection and radiation. The combustion process utilizes detailed gas and surface reaction models. The gas-phase model becomes a system of stiff ordinary differential equations while the solid phase reduces, after discretization, into a system of stiff ordinary differential-algebraic equations. The time evolution of the system came from alternating integrations of the quasi-steady gas and transient solid. This work outlines the numerical model and presents some sensitivity studies on important parameters including internal transfer coefficients, catalytic surface site density, and external heat-loss (if applicable). The model is compared to two experiments using CO fuel: (1) steady-state conversion through an isothermal platinum (Pt) tube and (2) transient propagation of a catalytic reaction inside a small Pt tube. The model requires internal mass-transfer resistance to match the experiments at lower residence times. Under mass-transport limited conditions, the model reasonably predicted exit conversion using global mass-transfer coefficients. Near light-off, the model results did not match the experiment precisely even after adjustment of mass-transfer coefficients. Agreement improved for the first case after adjusting the surface kinetics such that the net rate of CO adsorption increased compared to O2. The CO / O2 surface mechanism came from a sub-set of reactions in a popular CH4 / O2 mechanism. For the second case, predictions improved for lean conditions with increased external heat loss or adjustment of the kinetics as in the first case. Finally, the results show that different initial surface-species distribution leads to different steady-states under certain conditions. These results demonstrate the utility of a lumped two-phase model of a transient catalytic combustor with detailed chemistry.

Struk, Peter M.↗
DOE OSTI2021

Mass transport in nanoarray monolithic catalysts: An experimental-theory study

Reducing the mass transfer resistance globally of a catalyst is a key to enhancing the catalytic reaction kinetics and fully utilizing the catalyst activity. Despite the success in tailoring the external mass transfer in the widely studied washcoat monoliths, the internal mass transfer resistance is difficult to be reduced due to the requirement of increasing macroporosity while maintaining high specific surface area and mechanical stability. Therefore, nanostructured array-based monolithic catalysts (nanoarray catalysts) have been developed in the past decade as a promising class of structured catalysts that may complement or substitute washcoat catalysts. This work fundamentally elucidates the enhanced mass transport properties of the nanoarray monolithic catalysts by a combination of experimental measurements and theoretical modeling. Using a low-dimensional model, the relative contributions of resistances were quantified in terms of chemical kinetics, internal and external mass transfers based on a probe model of C2H4 oxidation over the TiO2 supported Pt-based monolithic catalysts. The nanoarray catalysts displayed a lower internal mass transfer resistance than the washcoat counterparts as a result of the high macroporosity and small thickness of nanoarray layers. Finally, the nanoarray configuration provides a new pathway towards designing high-performance monolithic reactors and catalysts with low internal diffusion limitations for various gas phase reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Estimating viscoelastic compliance of desiccating cementitious materials using drying prism tests

Highlights: • Determining relative humidity and degree of reaction of desiccating cementitious materials via an integrated method • Extracting moisture diffusion coefficient of cement mortar using the mass loss data of the prism specimens • Estimating uniaxial viscoelastic compliance of cement mortar using the shrinkage strain data of the prism specimens An integrated modeling approach to determining internal relative humidity and degree of reaction of desiccating cementitious materials has been developed. By simultaneously accounting for both self-desiccation and external drying, the model is capable of predicting the evolution of material properties of desiccating cementitious materials. Using the mass loss data of the prism specimens, the moisture diffusion coefficient of a nonlinear model for cement mortar was determined. Additionally, a previous poroviscoelastic shrinkage model was modified and extended. Through comparison of predicted and measured axial strain of the prism specimens, the viscoelastic compliance of cement mortar was extracted. The present work revealed that it is possible to use a simple drying prism test to fit the moisture diffusion coefficient and creep compliance of cementitious materials, though the comparison of the extracted viscoelastic compliance with measured compliance was only reasonable if the outer layer of the drying mortar was presumed to have microcracking.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Unexpected Formation of Metallofulleroids from Multicomponent Reactions, with Crystallographic and Computational Studies of the Cluster Motion

Abstract New multicomponent reactions involving an isocyanide, terminal or internal alkynes, and endohedral metallofullerene (EMF) Lu 3 N@C 80 yield metallofulleroids which are characterized by mass‐spectrometry, HPLC, and multiple 1D and 2D NMR techniques. Single crystal studies revealed one ketenimine metallofulleroid has ordered Lu 3 N cluster which is unusual for EMF monoadducts. Computational analysis, based on crystallographic data, confirm that the endohedral cluster motion is controlled by the position of the exohedral organic appendants. Our findings provide a new functionalization reaction for EMFs, and a potential facile approach to freeze the endohedral cluster motion at relatively high temperatures.

Li, Yanbang↗
NASA NTRS2020

Pterodactyl: Development and Comparison of Control Architectures for a Mechanically Deployed Entry Vehicle

The Pterodactyl project, seeks to advance the current state-of-the-art for entry vehicles by developing novel guidance and control technologies for Deployable Entry Vehicles (DEVs) that can be applied to various entry vehicle configurations. This paper details the efforts on the NASA-funded Pterodactyl project to investigate and implement multiple control techniques for an asymmetric mechanical DEV. We design multiple control architectures for a Pterodactyl Baseline Vehicle (PBV) and evaluate their performance in achieving varying guidance commands during entry. The control architectures studied are (i) propulsive control systems such as reaction control systems and (ii) non-propulsive control systems such as aerodynamic control surfaces and internal moving masses. For each system, state-feedback integral controllers based on linear quadratic regulator (LQR) optimal control methods are designed to track guidance commands of either (i) bank angle or (ii) angle of attack and sideslip angle as determined by the desired guidance trajectory. All control systems are compared for a lunar return reference mission and by providing a comparative analysis of these systems, configurations, and performance, the efforts detailed in this paper and the Pterodactyl project as a whole will help entry vehicle system designers determine suitable control architectures for integration with DEVs and other entry vehicle types.

Okolo, Wendy A.↗
NASA NTRS1991

The effects of shock wave precursors ahead of hypersonic entry vehicles

A model has been developed to predict the magnitude and characteristics of the shock wave precursor ahead of a hypervelocity vehicle. This model includes both chemical and thermal nonequilibrium, utilizes detailed mass production rates for the photodissociation and photoionization reactions, and accounts for the effects of radiative absorption and emission on the individual internal energy modes of both atomic and diatomic species. Comparison of the present results with shock tube data indicates that the model is reasonably accurate. A series of test cases representing earth aerocapture return from Mars indicate that there is significant production of atoms, ions and electrons ahead of the shock front due to radiative absorption and that the precursor is characterized by an enhanced electron/electronic temperature and molecular ionization. However, the precursor has a negligible effect on the shock layer flow field.

Stanley, Scott A.↗
NASA NTRS2007

Determination of Scopolamine in Human Saliva Using Solid Phase Extraction and LC/MS/MS

Purpose: Scopolamine is the preferred treatment for motion sickness during space flight because of its quick onset of action, short half-life and favorable side-effect profile. The dose administered depends on the mode of administration and usually ranges between 0.1 and 0.8 mg. Such small doses make it difficult to detect concentrations of scopolamine in biological fluids by using conventional HPLC methods. To measure scopolamine in saliva and thereby to evaluate the pharmacokinetics of scopolamine, we developed an LC/MS/MS method using off-line solid phase extraction. Method: Samples (0.5mL) were loaded onto Waters Oasis HLB co-polymer cartridges (10 mg, 1 mL) and eluted with 0.5 mL methanol without evaporation and reconstitution. HPLC separation of the eluted sample was performed using an Agilent Zorbax SB-CN column (50 x 2.1 mm) at a flow rate of 0.2 mL/min for 4 minutes. The mobile phase for separation was 90:10 (v/v) methanol: ammonium acetate (2 mM) in water, pH 5.0 +/- 0.1. Concentrations of scopolamine were determined using a Micromass Quattro Micro(TM) mass spectrometer with electrospray ionization (ESI). ESI mass spectra were acquired in positive ion mode with multiple reaction monitoring for the determination of scopolamine m/z = 304.2 yields 138.1 and internal standard (IS) hyoscyamine m/z = 290.2 yields 124.1. Results: The method is rapid, reproducible, specific and has the following parameters: scopolamine and the IS are eluted at 1.7 and 3.2 min respectively. The linear range is 50-5000 pg/mL for scopolamine in saliva with correlation coefficients > 0.99 with a CV < 0.5 %. The intra-day and inter-day CVs are < 15 % for quality control samples with concentrations of 75, 300, 750 and 3000 pg/mL of scopolamine in human saliva. Conclusion: Solid phase extraction allows more rapid sample preparation and greater precision than liquid extraction. Furthermore, we increased the sensitivity and specificity by adjusting the LC mobile phase and using an MS/MS detector.

Wang, Zuwei↗
NASA NTRS1993

Critical review of electrical conductivity measurements and charge distribution analysis of magnesium oxide

The electrical conductivity sigma of MgO single crystals shows a sharp increase at 500-800 C, in particular of sigma surface, generally attributed to surface contamination. Charge Distribution Analysis (CDA), a new technique providing information on fundamental properties that was previously unavailable, allows for the determination of surface charges, their sign and associated internal electric field. Data on 99.99% purity, arc-fusion grown MgO crystals show that mobile charge carriers start to appear in the bulk of the MgO crystals between 200 and 400 C when sigma (measured by conventional techniques) is in t he 10(exp -14) to 10(exp -16) /omega/cm range. Above 500 C, as sigma increases to 10(exp -6) to 10(exp -7)/omega/cm, more charges appear giving rise to a strong positive surface charge supported by a strong internal field. This indicates that charges are generated in the bulk and diffuse to the surface by an internally controlled process. On the basis of their positive sign they are identified as holes (defect electrons). Because of the low cation content of these very pure MgO crystals, theses holes cannnot be associated with transition metal impurties. Instead, they are associated with the O(2-) sublattice, e.g. consist of O(-) states or positive holes. This conclusion is supported by magnetic susceptibility data showing the appearance of 1000 +/- 500 ppm paramagnetic species between 200-500 C. The magnetic data are consistent with strongly coupled, diamagnetic O(-) pairs below 200-500 C, chemically equivalent to peroxy anions, O2(2-), and probably associated with cation vacancies in the MgO matrix. The formation of O2(2-) in arc-fusion grown MgO crystals is very unexpected because of the highly reducing growth conditions. Their presence implies an internal redox reaction involving dissolved 'water' by which OH(-) pairs convert to O2(2-) plus H2 molecules. This redox conversion is supported by mass spectroscopic measurements of the H2 release from highly OH(-)-doped, finely divided MgO and by wet-chemical analysis of its oxidant concentration.

Freund, Friedemann↗
NASA NTRS2008

A Modified LC/MS/MS Method with Enhanced Sensitivity for the Determination of Scopolamine in Human Plasma

Intranasal scopolamine is a choice drug for the treatment of motion sickness during space flight because of its quick onset of action, short half-life and favorable sideeffects profile. The dose administered usually ranges between 0.1 and 0.4 mg. Such small doses make it difficult to detect concentrations of scopolamine in biological fluids using existing sensitive LC/MS/MS method, especially when the biological sample volumes are limited. To measure scopolamine in human plasma to facilitate pharmacokinetic evaluation of the drug, we developed a sensitive LC/MS/MS method using 96 well micro elution plates for solid phase extraction (SPE) of scopolamine in human plasma. Human plasma (100-250 micro L) were loaded onto Waters Oasis HLB 96 well micro elution plate and eluted with 50 L of organic solvent without evaporation and reconstitution. HPLC separation of the eluted sample was performed using an Agilent Zorbax SB-CN column (50 x 2.1 mm) at a flow rate of 0.2 mL/min for 3 minutes. The mobile phase for separation was 80:20 (v/v) methanol: ammonium acetate (30 mM) in water. Concentrations of scopolamine were determined using a Micromass Quattro Micro(TM) mass spectrometer with electrospray ionization (ESI). ESI mass spectra were acquired in positive ion mode with multiple reaction monitoring for the determination of scopolamine m/z = 304.2 right arrow 138.1 and internal standard hyoscyamine m/z = 290.2 right arrow 124.1. The method is rapid, reproducible, specific and has the following parameters: scopolamine and the IS are eluted at about 1.1 and 1.7 min respectively. The linear range is 25-10000 pg/mL for scopolamine in human plasma with correlation coefficients greater than 0.99 and CV less than 0.5%. The intra-day and inter-day CVs are less than 15% for quality control samples with concentrations of 75,300, and 750 pg/mL of scopolamine in human plasma. SPE using 96 well micro elution plates allows rapid sample preparation and enhanced sensitivity for the LC/MS/MS determination of scopolamine in a small volume of biological samples. The new method is also cost effective since it uses a small volume of organic solvents compared to the methods using SPE cartridges or regular 96 well SPE plates. This method can be successfully used for bioavailability and pharmacokinetic evaluations of scopolamine, especially when volumes of biological samples are limited. Further investigation to use automated SPE system with 96 well micro elution plates is planned.

Wang, Zuwei↗
NASA NTRS1976

Photoionization and ion cyclotron resonance studies of the ion chemistry of ethylene oxide

The formation of the ethylene oxide molecular ion and its subsequent ion-molecule reactions leading to the products C2H5O(+) and C3H5O(+) have been studied using time-resolved photoionization mass spectroscopy, ion cyclotron resonance spectroscopy, and photoelectron spectroscopy. An examination of the effects of internal energy on reactivity shows that the ratio of C3H5O(+) to C2H5O(+) increases by an order of magnitude with a single quantum of vibrational energy. The formation of (C2H4O/+/)-asterisk in a collision-induced isomerization is found which yields a ring-opened structure by C-C bond cleavage. The relaxed ring-opened C2H4O(+) ion reacts with neutral ethylene oxide by CH2(+) transfer to yield an intermediate product ion C3H6O(+) which gives C3H5O(+) by loss of H.

Corderman, R. R.↗
DOE OSTI2023

Constraining the Reaction Rate of Criegee Intermediates with Carboxylic Acids during the Multiphase Ozonolysis of Aerosolized Alkenes

Criegee intermediates (CIs) are central to the ozonolysis of unsaturated organic compounds, controlling the formation of small fragmentation reaction products and higher molecular weight oligomeric compounds through competing unimolecular and bimolecular pathways. In particular, the reaction of thermalized CI with carboxylic acids (RCOOH) to produce oligomeric α-acyloxyalkyl hydroperoxides (AAHPs) is of interest to the chemical transformation of organic compounds in the atmosphere. In the gas phase, the CI + RCOOH reaction proceeds at supercollisional rates, consistent with a barrierless reaction mechanism. However, the rate of this reaction in condensed phases remains uncertain. Here, we report the results of aerosol flow tube studies of the ozonolysis of submicron organic aerosol containing mixtures of an internal n-alkene (Z-9-tricosene, tri) and a saturated acid (2-hexyldecanoic acid, HDA). The decay of the reactants and formation of reaction products are monitored using atmospheric pressure chemical ionization mass spectrometry (APCI–MS). A 6-fold decrease in the reactive uptake of ozone is observed with increasing acid concentration, consistent with a previous study using alcohol additives. The decay of HDA with ozone exposure shows that HDA scavenges CIs at rates comparable to competing unimolecular pathways involving CIs. The decay kinetics of HDA are analyzed using a simple kinetic model in order to constrain the ratio of the CI + RCOOH and unimolecular CI rate constants. Empirical fitting to this model, combined with theoretical estimates of the unimolecular loss rate, yields a CI + RCOOH rate constant of 1.85 ± 0.27 × 10 –19 cm 3 molec –1 s –1 , which is six orders of magnitude slower than the expected diffusion limit in a liquid organic matrix. Stochastic kinetic simulations are conducted with different values of the CI + RCOOH rate constant to validate this result and show that the diffusion-limited rate is indeed much too rapid to reproduce the experimental results.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2020

Pterodactyl: Control Architectures Development for Integrated Control Design of a Mechanically Deployed Entry Vehicle

The need to return high mass payloads is driving the development of a new class of vehicles, Deployable Entry Vehicles (DEV) for which feasible and optimized control architectures have not been developed. The Pterodactyl project, seeks to advance the current state-of-the-art for entry vehicles by developing a design, test, and build capability for DEVs that can be applied to various entry vehicle configurations. This paper details the efforts on the NASA-funded Pterodactyl project to investigate multiple control techniques for the Lifting Nano-ADEPT (LNA) DEV. We design and implement multiple control architectures on the LNA and evaluate their performance in achieving varying guidance commands during entry.First we present an overview of DEVs and the Lifting Nano-ADEPT (LNA), along with the physical LNA configuration that influences the different control designs. Existing state-of-the-art for entry vehicle control is primarily propulsive as reaction control systems (RCS) are widely employed. In this work, we analyze the feasibility of using both propulsive control systems such as RCS to generate moments, and non-propulsive control systems such as aerodynamic control surfaces and internal moving mass actuations to shift the LNA center of gravity and generate moments. For these diverse control systems, we design different multi-input multi-output (MIMO) state-feedback integral controllers based on linear quadratic regulator (LQR) optimal control methods. The control variables calculated by the controllers vary, depending on the control system being utilized and the outputs to track for the controller are either the (i) bank angle or the (ii) angle of attack and sideslip angle as determined by the desired guidance trajectory. The LQR control design technique allows the relative allocation of the control variables through the choice of the weighting matrices in the cost index. Thus, it is easy to (i) specify which and how much of a control variable to use, and (ii) utilize one control design for different control architectures by simply modifying the choice of the weighting matrices.By providing a comparative analysis of multiple control systems, configurations, and performance, this paper and the Pterodactyl project as a whole will help entry vehicle system designers and control systems engineers determine suitable control architectures for integration with DEVs and other entry vehicle types.

Okolo, Wendy A.↗
NASA NTRS1994

Characterization of Hybrid Rocket Internal Heat Flux and HTPB Fuel Pyrolysis

None given. From statement of problem:The broad nature of this work has been to extend our understanding of the nature of the conventional or classical hybrid rocket combustion process (fuel decomposition, heat and mass transfer, and chemical reaction), and the critical engineering parameters that define this process.

rocket↗
DOE OSTI2021

Membrane-Confined Iron Oxychloride Nanocatalysts for Highly Efficient Heterogeneous Fenton Water Treatment

Heterogeneous advanced oxidation processes (AOPs) allow for the destruction of aqueous organic pollutants via oxidation by hydroxyl radicals ( • OH). However, practical treatment scenarios suffer from the low availability of short-lived • OH in aqueous bulk, due to both mass transfer limitations and quenching by water constituents, such as natural organic matter (NOM). In this work, we overcome these challenges by loading iron oxychloride catalysts within the pores of a ceramic ultrafiltration membrane, resulting in an internal heterogeneous Fenton reaction that can degrade organics in complex water matrices with pH up to 6.2. With • OH confined inside the nanopores (~ 20 nm), this membrane reactor completely removed various organic pollutants with water fluxes of up to 100 L m –2 h –1 (equivalent to a retention time of 10 s). This membrane, with a pore size that excludes NOM (>300 kDa), selectively exposed smaller organics to •OH within the pores under confinement and showed excellent resiliency to representative water matrices (simulated surface water and sand filtration effluent samples). Moreover, the membrane exhibited sustained AOPs (>24 h) and could be regenerated for multiple cycles. Our results suggest the feasibility of exploiting ultrafiltration membrane-based AOP platforms for organic pollutant degradation in complex water scenarios.

36 MATERIALS SCIENCE↗