Search NASA⌕ Search

SEARCH · Search NASA

Results for “intragranular strain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Measuring residual stress in Ti-6Al-4V with HR-EBSD, using reference patterns from annealed material

In this study, elastic strain and residual stress values in an engineering material were determined by high-resolution EBSD (HR-EBSD) using reference patterns from annealed, recrystallized material. Specifically, rolled Ti-6Al-4V sheet was analyzed using HR EBSD in both an as-annealed and a strained state, the latter established via a static two-point bend fixture. The commercial software CrossCourt4 (CC4) was used to evaluate the relative intragranular strain tensor components of the alpha grains mapped by HR-EBSD. The intragranular reference patterns identified in each grain by the software were then replaced with similarly-oriented patterns from scans of the as-annealed, recrystallized material. The CC4 analysis was then repeated to provide calibrated strain and residual stress values. Elastic strains on the order of 10–3 were detected, with corresponding residual stress values on the order of 1 GPa. Subsequent analyses using high energy synchrotron x-ray diffraction showed good correlation with the elastic strains measured by HR-EBSD using the annealed reference patterns. Additionally, the maximum macroscopic stress analytically predicted for two-point bending was in agreement with the residual stress observed. Good repeatability of the methodology and insight into the state of individual grains were also observed. The findings provide encouraging evidence that accurate intragranular and long-range residual stress measurements of engineering significance can be made with HR-EBSD using a physical reference pattern library.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Local residual stresses and microstructure within recrystallizing grains in iron

The intragranular strains and the microstructure within recrystallizing grains in single phase pure iron have been systematically studied in 3D using synchrotron micro-diffraction. In contradiction to common knowledge we observe that residual elastic strains of up to 1–2 × 10 –3 are present in the recrystallizing grains. The local strain variations within individual grains can be similar in magnitude to those between different grains. The effects of processing parameters, including rolling reduction, recrystallized volume fraction, and cooling rate, as well as microstructural parameters, including grain size, orientation and internal misorientation, on the development of local residual elastic strains and microstructure have been quantified. It is suggested that the difference in local defect density between recrystallized grains and the surrounding deformed matrix, as well as the redistribution of medium to long-range residual stresses in the deformed grains, are the main reasons for the development of such strains in the recrystallized grains. The local residual stress levels are calculated and their possible impact on the mechanical properties and recrystallization processes are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The effect of microstructure on the relationship between grain boundary sliding and slip transmission in high purity aluminum

The relationship between grain boundary sliding (GBS) and slip transmission is investigated experimentally at grain boundaries in 99.99% aluminum with a through-thickness, coarse grained microstructure deformed in tension at 190 °C. Using scanning electron microscope enabled digital image correlation (SEM-DIC) and electron backscatter diffraction (EBSD), high resolution strain fields and microstructural information were measured to examine the influence of microstructural neighborhoods on interactions between GBS and slip transmission and strain localization. Several distinct cases are presented that highlight important microstructural factors that govern deformation near grain boundaries. The findings include (1) direct transmission and GBS were anti-compatible and facilitated by opposing boundary types (low misorientation and high energy grain boundaries respectively); (2) increased GBS activity was correlated with decreased indirect transmission behavior; (3) GBS accommodation at triple junctions was enabled by intragranular plasticity; and (4) the local intragranular plastic strain discontinuity between grains determined the magnitude of GBS gradients. Finally, this work provides insight into the nature of these mechanisms and can be used to identify strain transfer criteria that can lead to improved GBS-sensitive crystal plasticity models.

36 MATERIALS SCIENCE↗
DOE OSTI2022

($\mathrm{INVITED}$)Counter-ion effect on the diffusion behavior of $\mathrm{Y}$b, $\mathrm{L}$u, and $\mathrm{N}$d ions in $\mathrm{YAG}$ transparent ceramics

The ability to fabricate additively manufactured laser waveguides with sharp dopant concentration interfaces is limited by diffusion of the dopants at the temperatures required to fully densify the material. Compositional analysis of bilayer samples, where each layer was either undoped YAG or YAG doped with Yb, Lu, or Nd, were fabricated such that all combinations were available for testing. Samples were fabricated at both 1750°C and 1850°C to determine the diffusion behavior of each dopant alone and also in the presence of a second dopant. It was found that the experimental concentration profiles exhibited both intragranular (bulk) and grain boundary contributions, and thus fitting to a complementary error function equation required the use of two diffusion coefficients. Nd always diffused further along grain boundaries than the other dopants, due in part to its small segregation coefficient in YAG. It is shown that the presence of Nd as a counter dopant inhibits intragranular diffusion of other dopants while enhancing their grain boundary diffusion. All the observed trends were attributed to a combination of intragranular lattice strain due to: dopant ions replacing yttrium substitutionally, the relative driving forces for the segregation of dopant ions to grain boundaries, and the ability of one dopant to affect the diffusion of a different dopant in the other direction to maintain charge neutrality.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Accumulative Roll Bonding of Alloy 2205 Duplex Steel and the Accompanying Impacts on Microstructure, Texture, and Mechanical Properties

The mechanical and microstructural evolution of Alloy 2205 during severe plastic deformation is examined in this study. A combination of accumulative roll bonding (ARB) and cold rolling results in the successful formation of a nanograined dual-phase microstructure of austenite and ferrite with some transformed martensite. Severe deformation to cumulative reductions of 80.5, 92.5, 95, and 97 pct were performed. Microscopy indicates that grain dimensions in the sheet normal direction is less than 100 nm for reductions ≥ 92.5 pct. Shear banding is observed at reductions ≥ 95 pct while twinning is only observed at reductions < 92.5 pct. Neutron diffraction measurements indicated the presence of martensite for reductions ≥ 95 pct at ~ 8 pct volume fraction. Taken in conjunction, it appears that during initial ARB processing, both slip and twinning are active plastic mechanisms. As twinning becomes exhausted, martensitic transformation, slip, and intermittent shear banding account for the active plasticity mechanisms. Material hardness saturates at 92.5 pct reduction, with a maximum hardness of 45 HRC. Sub-sized tensile testing confirms this approximate hardness with measurements indicating a UTS of ~ 1440 MPa. Texture analysis of crystal orientation distributions in the plate normal direction suggest an approximate Kurdjumov–Sachs orientation relationship at all reductions above 80 pct indicating stability of the orientation relationship at high strains. The intragranular structure develops a fine scale sub-grain content with increasing deformation, resulting in a continual evolution of texture up to and including 97 pct reduction. The final structure presents strong components of Goss and rotated cube texture in both the austenite and ferrite. In this body of work we aim to compare ARB of an industrially relevant FCC/BCC system (Alloy 2205) to historical model FCC/BCC systems such as Cu/Nb.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Shear strain gradient in Cu/Nb nanolaminates: Strain accommodation and chemical mixing

Disentangling the intragranular and interfacial plasticity contribution to the overall strain accommodation is crucial to understanding the microstructural evolution and mass transport upon deformation in materials with the nanoscale feature size. In this study, we devise a new approach to tackle the issue by introducing shear strain gradients into Cu/Nb nanolaminates of different layer thicknesses with the shear perpendicular to the laminate interfaces. The measurement of the strain gradient and the resultant lattice disorientation enables a quantitative understanding of the intragranular and interfacial plasticity contribution. We found that intragranular slip entirely governs the deformation in the 300 nm-layer laminate and, unexpectedly, contributes ~80% of the total plasticity in the 30 nm-layer laminate. The high intragranular plasticity in the thin laminate is attributed to the large width of confined slip planes and their remnant potential for storing dislocations. In addition, substantial forced chemical mixing is observed in the top region of the 30 nm-layer laminate where the effective layer thickness is reduced below 8 nm. The transition of deformation mechanism from confined layer slip to dislocation transmission is largely responsible for the initiation of substantial mixing. Our method and findings shed light on the deformation mechanism and deformation-induced mass transport behavior in nanostructured materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Modeling of the thermo-mechanical response and texture evolution of WE43 Mg alloy in the dynamic recrystallization regime using a viscoplastic self-consistent formulation

This paper presents a microstructure sensitive model for predicting mechanical response and texture evolution of metals in the dynamic recrystallization regime. A recently proposed viscoplastic self-consistent (VPSC) formulation for the prediction of recrystallization driven by strain energy and intragranular misorientation is extended to hexagonal close-packed (hcp) metals. The model is applied to the dynamic recrystallization of magnesium alloy WE43 at different temperatures and strain rates. Model predictions in terms of stress-strain response and texture evolution are compared to the experimental measurements and acceptable agreement is achieved. According to the model predictions, superplastic behavior of nuclei was found to be the dominant softening mechanism at high temperatures and low strain rates. High concentration of precipitates at the grain boundaries and presence of alloying elements are the likely causes of low boundary mobility, resulting in nucleation dominated dynamic recrystallization. Relatively strong basal compression textures indicate dominant activity of basal slip, which can be achieved only through large difference in slip resistance between soft basal and hard prismatic and pyramidal modes.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High-resolution 3D strain and orientation mapping within a grain of a directed energy deposition laser additively manufactured superalloy

The industrialization of Laser Additive Manufacturing (LAM) is challenged by the undesirable microstructures and high residual stresses originating from the fast and complex solidification process. Non-destructive assessment of the mechanical performance controlling deformation patterning is therefore critical. Here, we use Dark Field X-ray Microscopy (DFXM) to map the 3D subsurface intragranular orientation and strain variations throughout a surface-breaking grain within a directed energy deposition nickel superalloy. DFXM results reveal a highly heterogenous 3D microstructure in terms of the local orientation and lattice strain. The grain comprises ≈ 5 μm-sized cells with alternating strain states, as high as 5 x10 -3 , and orientation differences <0.5°. The DFXM results are compared to Electron Backscatter Diffraction measurements of the same grain from its cut-off surface. Here, we discuss the microstructure developments during LAM, rationalising the development of the deformation patterning from the extreme thermal gradients during processing and the susceptibility for solute segregation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Void coalescence and ductile failure in IN718 investigated via high-energy synchrotron X-ray tomography and diffraction

Ductile failure through the growth and coalescence of voids is of particular relevance for many engineering materials. Yet, the lack of experimental measurements of the mechanical state of the material at an appropriate length scale has limited further understanding of the regime of ductile failure. In this study, local grain-scale experimental measurements are used to determine their relevance for describing and predicting ductile failure. Additive manufactured materials, due to the presence of inherent porosity, as well as the ability to tailor internal porosity, provides a promising avenue to study ductile failure. Selective laser melting is used to manufacture a specially designed specimen with two large, internal voids, in addition to the natural porosity, which is characteristic to the production process. The initial porosity and its evolution upon tensile loading are characterized via micro tomography. Several locations of void coalescence are captured in the sample, revealing activity of multiple modes of failure. Finite element simulations, with a simplified J2 plasticity model, instantiated with the initial void structure, is deployed, in which geometric localizations of stress concentration corresponded with experimentally observed sites of coalescence but was inadequate in capturing the appropriate failure mechanism. Furthermore, from the experimental results of the far-field high-energy diffraction microscopy, the heterogeneous micromechanical state is identified and tracked around voids due to the local grain interactions. These experiments determine narrow bands of low stress triaxiality, at the onset of failure, which highlight the path of coalescence through intervoid shearing. Diffraction spot spreading analysis aided characterization of intragranular plasticity and strain heterogeneity, which can be coupled with high triaxiality to form the conditions inducive for coalescence through intervoid necking. In this study, the experimentally determined grain-scale description of the micromechanical state provides a physical basis that can accurately capture both the sites and the mechanism of void coalescence at the onset of ductile failure.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Resolving intragranular stress fields in plastically deformed titanium using point-focused high-energy diffraction microscopy

Abstract The response of a polycrystalline material to a mechanical load depends not only on the response of each individual grain, but also on the interaction with its neighbors. These interactions lead to local, intragranular stress concentrations that often dictate the initiation of plastic deformation and consequently the macroscopic stress–strain behavior. However, very few experimental studies have quantified intragranular stresses across bulk, three-dimensional volumes. In this work, a synchrotron X-ray diffraction technique called point-focused high-energy diffraction microscopy (pf-HEDM) is used to characterize intragranular deformation across a bulk, plastically deformed, polycrystalline titanium specimen. The results reveal the heterogenous stress distributions within individual grains and across grain boundaries, a stress concentration between a low and high Schmid factor grain pair, and a stress gradient near an extension twinning boundary. This work demonstrates the potential for the future use of pf-HEDM for understanding the local deformation associated with networks of grains and informing mesoscale models. Graphical abstract

36 MATERIALS SCIENCE↗
DOE OSTI2025

The influence of kinematics of deformation on polycrystalline halite dynamic recrystallization: Full-field simulation of simple shear versus pure shear

Rock salt, composed mainly of halite, flows viscoplastically over a wide range of geological conditions, strongly impacting the dynamic evolution of sedimentary basins and orogens. Understanding how dislocation creep, which involves dislocation glide, intracrystalline recovery and dynamic recrystallization, influences the microstructure and rheology of halite under various deformation kinematics and temperatures is crucial for enhancing knowledge of salt flow dynamics. Here, this study employs a full-field numerical simulation method to compare the viscoplastic deformation of polycrystalline halite under simple shear and pure shear conditions up to a natural strain of ε = 1.5 at temperatures ranging from 100 °C to 300 °C. The results are presented in terms of crystallographic preferred orientation (CPO), grain shape preferred orientation (SPO), subgrain boundary direction, grain size and strain rate distribution. The results indicate that the crystallographic anisotropy of individual halite crystals is transferred to the polycrystalline scale, resulting in strain localization, particularly in simple shear simulations. The kinematics of deformation affect the evolution and distribution of high strain-rate bands, determining the direction of intragranular substructures and the morphology of strain-induced grain boundaries, with minimal impact on grain size. The intensity of grain boundary migration increases with temperature, significantly influencing grain morphology and size, thereby obscuring strain localization, while having little effect on CPOs. At low strain (ε < 1.0), CPOs relative to both the maximum shortening direction and the grain SPO are similar regardless of the deformation kinematics. At high strain (ε > 1.0), simple shear CPOs exhibit three stronger {100} maxima with a monoclinic symmetry relative to the grain SPO compared to the six {100} maxima with an orthotropic symmetry relative to the grain SPO generated under pure shear. Therefore, microstructures and CPOs can serve as indicators of the strain path in polycrystalline halite under various conditions, aiding in determining the shear sense and elucidating the deformation kinematics of salt structures.

58 GEOSCIENCES↗
DOE OSTI2022

Spatiotemporal mapping of microscopic strains and defects to reveal Li-dendrite-induced failure in all-solid-state batteries

Solid-state electrolytes (SSEs) are key to the success and reliability of all-solid-state lithium batteries, potentially enabling improvements in terms of safety and energy density over state-of-the-art lithium-ion batteries. However, there are several critical challenges to their implementation, including the interfacial instability stemming from the dynamic interaction of as-formed dendritic lithium during cycling. Here, we emphasize the importance of studying the spatial distribution and temporal evolution of strains and defects in crystalline solid-state electrolytes at the micro-scale, and how this affects dendrite growth. A proof-of-principle study is demonstrated using the synchrotron radiation based micro Laue X-ray diffraction method, and a custom-developed in-situ cycling device. Defects and residual strains are mapped, and the evolution of intragranular misorientation is observed. The feasibility of using this technique is discussed, and recommendations for micro-strain engineering to address the Li/SSEs interfacial issues are given. Additionally, work directions are pointed out with the consideration of combining multi-techniques for “poly-therapy”.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Micromechanical and fatigue in situ synchrotron characterization of an additively manufactured superalloy with porosity

Additive manufacturing (AM) has the potential to transform component production, but its widespread adoption is constrained by defects, such as pores, that compromise structural integrity. Here, this study investigates the influence of porosity on the micromechanical and fatigue response of AM Inconel 718 (IN718), a widely used aerospace superalloy. One baseline specimen with minimal stochastic porosity and another intentionally seeded with lack of fusion (LOF) pores were examined using high-energy X-ray diffraction microscopy (HEDM) and micro-computed tomography during cyclic loading. Fatigue cracks in the LOF specimen initiated more frequently and at lower cycle counts than in the baseline specimen. The number fraction of fatigue cracks that grew was comparatively higher in the LOF specimen. Grain-level metrics, including stress and diffraction spot widths, were quantified using far-field HEDM. Across the thousands of grains detected in both specimens, the pores in the LOF specimen increased the variability of stress and spot width evolution in the azimuthal direction, the latter serving as a surrogate measure of plastic deformation. However, no correlations emerged between these metrics and grain proximity to fatigue crack initiation sites or pores, underscoring the limitations of grain-averaged metrics for predicting fatigue. Nonetheless, the rich dataset reported here provides a foundation for future modeling efforts.

High-energy X-ray diffraction microscopy↗
DOE OSTI2024

Resolving crystallographic geometrically necessary dislocations in three dimensions in a hexagonal close packed titanium alloy

Abstract Geometrically necessary dislocation (GND) content is measured from mm 3 -scaled Ti7Al three-dimensional (3D) microstructural data using a theory extended for hexagonal close packed crystals, which accounts for basal, prismatic and pyramidal ⟨ c + a ⟩ type dislocation content. The Ti7Al samples have been mechanically pre-strained to two different strain levels, and will then be strained along the same axis in uniaxial tension during simulation. Both inter- and intragranular GNDs across the microstructures have been characterized, with a large contribution of pyramidal ⟨ c + a ⟩ GNDs, consistent with the relative slip activity involved in pre-straining. The spatially resolved crystallographic GND distributions within the 3D microstructures are used to instantiate a microstructure model for forward modeling deformation simulations by a dislocation density hardening elasto-viscoplastic fast Fourier transform framework. Coarsening the voxel resolution during the initial microstructure construction procedure is shown to strongly impact both the magnitude and spatial distribution of the GNDs and in turn the forward deformation response of the pre-strained material. This study indicates that the voxel resolution desired when transferring from measured to model microstructures need not only be proportionally scaled with the microstructure but also sufficiently fine to capture the subgranular orientation gradients that may already be present in the material.

Materials Science↗
DOE OSTI2020

High-Energy X-Ray Diffraction Microscopy in Materials Science

High-energy diffraction microscopy (HEDM) is an implementation of three-dimensional X-ray diffraction microscopy. HEDM yields maps of internal crystal orientation fields, strain states, grain shapes and locations as well as intragranular orientation distributions, and grain boundary character. Because it is nondestructive in hard materials, notably metals and ceramics, HEDM has been used to study responses of these materials to external fields including high temperature and mechanical loading. Currently available sources and detectors lead to a spatial resolution of ~1 μm and an orientation resolution of <0.1°. With the penetration characteristic of high energies ( E ≥ 50 keV), sample cross-section dimensions of ~1 mm can be studied in materials containing elements across much of the Periodic Table. This review describes hardware and software associated with HEDM as well as examples of applications. Overall, these applications include studies of grain growth, recrystallization, texture development, orientation gradients, deformation twinning, annealing twinning, plastic deformation, and additive manufacturing. We also describe relationships to other X-ray-based methods as well as prospects for further development.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Nanoindentation Investigation of Chloride-Induced Stress Corrosion Crack Propagation in an Austenitic Stainless Steel Weld

Transgranular chloride-induced stress corrosion cracking (TGCISCC) is a mounting concern for the safety and longevity of arc welds on austenitic stainless steel (AuSS) nuclear waste storage canisters. Recent studies have shown the key role of crystallography in the susceptibility and propagation of TGCISCC in SS weldments. Given that crystallography underlies mechanical heterogeneities, the mechanical-crystallographic relationship during TGCISCC growth must be understood. In this study, welded SS 304L coupons are loaded in four-point bend fixtures and then boiled in magnesium chloride to initiate TGCISCC. Nanoindentation mapping is paired with scanning electron microscopy (SEM) electron backscatter diffraction (EBSD) to understand the correlation between grain orientation, grain boundaries, and hardening from TGCISCC propagation. The nanoindentation hardness of individual grains is found to not be a controlling factor for TGCISCC propagation. However, intragranular hardness is generally highest immediately around the crack due to localized strain hardening at the crack tip. This work shows that nanoindentation techniques can be useful in understanding CISCC behaviors when paired with electron microscopy.

36 MATERIALS SCIENCE↗
DOE OSTI2020

New self-consistent homogenization for thermo-elastic polycrystals with imperfect interfaces

Here we present a new thermo-elastic self-consistent formulation to calculate the thermo-mechanical response of polycrystalline aggregates with imperfect interfaces. The new model is based on an improved treatment of the effect of imperfect interfaces on the micromechanical response of the grains compared to pre-existing models. New expressions/algorithms are derived for the effective elastic and thermal properties, localization relations, and calculation of intragranular field fluctuations. In addition, derivation of a novel integral equation for the strain field in a heterogeneous elastic medium subjected to arbitrary thermal strain field and displacement jumps is presented. The new model is applied to study the effective thermo-elastic properties and average field fluctuations as a function of the interface properties for imperfectly-bonded triaminotrinitrobenzene (TATB) polycrystalline granular aggregates. The proposed formulation is general in the sense that it can be extended to other material systems and deformation regimes that require a proper consideration of the effect of imperfect interface properties on the material's thermo-mechanical response.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Intralattice-bonded phase-engineered ultrahigh-Ni single-crystalline cathodes suppress strain evolution

Single crystallization remains a debated strategy for advancing Ni-rich cathode materials. While it mitigates particle cracking and improves tap density by eliminating particle boundaries, extended diffusion pathways introduce volumetric and lattice distortions, compromising electrochemical and structural stability. These challenges hinder the commercialization of high-Ni single-crystal cathodes, calling for a reassessment of their viability. Here, in this study, we report a structural design: intralattice-bonded phase single-crystal LiNi 0.92 Co 0.03 Mn 0.05 O 2 (IBP-SC92). This architecture maintains structural integrity while shortening diffusion pathways, resulting in almost zero electrochemical degradation during cycling. The robust structure and fast ion transport mitigate lattice strain, as confirmed by multiscale high-resolution diffraction and imaging techniques, preventing intragranular cracks and irreversible phase transitions. As a result, IBP-SC92 shows outstanding cycling stability, with nearly 100% capacity retention after 100 cycles in half cells and 94.5% retention after 1,000 cycles in full cells. This redefined single-crystal cathode represents a significant step towards the industrial adoption of high-energy-density materials.

36 MATERIALS SCIENCE↗